IllustrationPOWER STEERING GOES OUT SPORADICALLY. THERE HAVE BEEN THREE OCCASIONS SO FAR IN THE PAST YEAR THAT THE POWER STEERING HAS WENT OUT ON MY MAZDA 5. TWICE I WAS ABLE TO STOP THE CAR WAIT TEN SECONDS AND RESTART THE CAR AND IT RESET. ONCE IT TOOK TWO HOURS OF SITTING OFF BEFORE IT RESET ITSELF. *TR
2008 Mazda MAZDA5
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2008 Mazda MAZDA5 do not stand out strongly from the model-year median of 37.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA5 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
240–25K
1525–50K
950–75K
375–100K
6100–150K
3150K+
60 reports with mileage · 7 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 37 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Suspension. Review the 9 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Tires. Review the 7 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
4 crash reports1 fire reports2 injury reports
What owners actually said
67 reportsDRIVING FOR 2 HOURS OF A 4 HOUR DRIVE, POWER STEERING WENT OUT ON VEHICLE. I WAS STOPPED AT A GAS STATION AND WENT TO PULL OUT WHEN IT HAPPENED. IT HAD NOT HAPPENED BEFORE AND 24 HOURS LATER IT WAS WORKING AGAIN. MAZDA HAS TAKEN MY CAR FOR REPAIR AND HAS GIVEN ME A RENTAL CAR. HOWEVER DUE TO THE FREQUENCY WITH WHICH THIS HAS…
Read full complaint
DRIVING FOR 2 HOURS OF A 4 HOUR DRIVE, POWER STEERING WENT OUT ON VEHICLE. I WAS STOPPED AT A GAS STATION AND WENT TO PULL OUT WHEN IT HAPPENED. IT HAD NOT HAPPENED BEFORE AND 24 HOURS LATER IT WAS WORKING AGAIN. MAZDA HAS TAKEN MY CAR FOR REPAIR AND HAS GIVEN ME A RENTAL CAR. HOWEVER DUE TO THE FREQUENCY WITH WHICH THIS HAS BEEN HAPPENING TO THE MAZDA 5 THE PARTS (PUMP AND PIPE) ARE ON BACK ORDER AND MY CAR WILL NOT BE REPAIRED AND RETURNED FOR 15 WEEKS. IF I WERE TO TAKE POSSESSION OF MY CAR I WOULD HAVE TO SIGN A WAIVER THAT MAZDA IS NOT RESPONSIBLE FOR ANY ACCIDENT IF IT IS CAUSED BY THE PART FAILURE. *TR
DRIVERS FLOOR MAT RETAINING CLIP BEGINS TO SEPARATE FROM NORMAL USAGE. SEPARATION ALLOWS MAT TO MOVE FORWARD ENOUGH THAT EDGE OF MAT IS CAUGHT BY CLUTCH PEDAL DURING GEAR CHANGES. MAT LIFTS OVER CLUTCH PEDAL AND BECOMES ENTANGLED WITH CLUTCH AND BRAKE PEDAL WHEN TRYING TO SHIFT GEARS. MAT INTERFERENCE CAUSES ACCIDENTAL AND AGGRE…
Read full complaint
DRIVERS FLOOR MAT RETAINING CLIP BEGINS TO SEPARATE FROM NORMAL USAGE. SEPARATION ALLOWS MAT TO MOVE FORWARD ENOUGH THAT EDGE OF MAT IS CAUGHT BY CLUTCH PEDAL DURING GEAR CHANGES. MAT LIFTS OVER CLUTCH PEDAL AND BECOMES ENTANGLED WITH CLUTCH AND BRAKE PEDAL WHEN TRYING TO SHIFT GEARS. MAT INTERFERENCE CAUSES ACCIDENTAL AND AGGRESSIVE BRAKE APPLICATION WHEN ATTEMPTING TO SHIFT GEARS. MAT HAS BEEN REPLACED BY DEALER PREVIOUSLY BUT PROBLEM RETURNS AFTER A FEW MONTHS OF USAGE. *TR
VAN HAS 15,000 MILES AND IS APPROX 14 MONTHS OLD. VEHICLE WAS DIAGNOSED WITH EXCESSIVE TIRE WEAR IN THE FRONT AND TIRE CUPPING IN THE REAR, CREATING EXCESSIVE ROAD/TIRE NOISE INSIDE OF THE VEHICLE CABIN. *TR
TL*THE CONTACT OWNS A 2008 MAZDA 5. THE CONTACT STATED THAT THERE WERE LOOSE BOLTS ON THE REAR PASSENGER SIDE SUSPENSION. WHILE DRIVING VARIOUS SPEEDS, THE CONTACT HEARD LOUD POPPING NOISES. THE VEHICLE WAS TAKEN TO THE DEALER ONCE AND THEY PLANNED ON REPLACING THE BUSHING AND TIGHTENING THE BOLTS ON THE SUSPENSION. THE INNE…
Read full complaint
TL*THE CONTACT OWNS A 2008 MAZDA 5. THE CONTACT STATED THAT THERE WERE LOOSE BOLTS ON THE REAR PASSENGER SIDE SUSPENSION. WHILE DRIVING VARIOUS SPEEDS, THE CONTACT HEARD LOUD POPPING NOISES. THE VEHICLE WAS TAKEN TO THE DEALER ONCE AND THEY PLANNED ON REPLACING THE BUSHING AND TIGHTENING THE BOLTS ON THE SUSPENSION. THE INNER WALLS OF THE TIRES WERE WEARING OFF DUE TO THE LOOSE BOLTS, WHICH ALSO CAUSED THE SUSPENSION TO SLOWLY DETACH. THE VEHICLE IS CURRENTLY IN THE SHOP FOR REPAIR. THE CONTACT DISCOVERED THAT SEVERAL OTHER CONSUMERS WERE EXPERIENCING SUSPENSION FAILURE AS WELL. THE FAILURE MILEAGE WAS 17,000 AND CURRENT MILEAGE WAS 21,000.
WE BOUGHT A 2008 MAZDA5 AND HAVE HAD TO TAKE IT TO THE DEALER TWICE FOR LOOSE BOLTS ON THE REAR RIGHT SUSPENSION. THE CAR HAS LESS THAN 2000 MILES ON IT. WE ARE CONCERNED ABOUT THE SAFETY OF THE CAR. *TR
TL*THE CONTACT OWNS A 2008 MAZDA 5. WHILE DRIVING 65 MPH, THE SUNROOF SUDDENLY EXPLODED. THE SUNROOF WAS CLOSED AT THE TIME OF THE FAILURE. THE VEHICLE WAS TAKEN TO THE DEALER AND THEY STATED THAT SOMEONE IN THE VEHICLE CAUSED THE FAILURE. THE CURRENT AND FAILURE MILEAGES WERE 4,100.
Official recalls
110V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.