IllustrationEACH OF MY HEADLIGHTS HAVE GONE OUT 3 TIMES WITHIN 25,000 MILES AND 1 1/2 YEARS OF DRIVING IT. *TR
2008 Mazda MAZDA3
Owner reports · Recalls · Investigations
More warning signs than most MAZDA3 years
Owner complaints for the 2008 Mazda MAZDA3 are substantially higher than the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
620–25K
8925–50K
4050–75K
3475–100K
25100–150K
6150K+
256 reports with mileage · 47 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 117 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Tires. Review the 41 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Wheels. Review the 33 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
29 crash reports1 fire reports16 injury reports
What owners actually said
303 reportsTIRE SENSOR CAME ON DURING DRIVE INTO WORK. MADE TO CALL DEALERSHIP TO HAVE IT CHECKED OUT BY LUNCH TIME THE REAR PASSENGER SIDE TIRE WAS COMPLETELY FLAT AND THE STEM OF THE TIRE PRESSURE MONITOR HAD COMPLETELY SNAPPED OFF. WHEN I GOT THE CAR TO A DEALER THEY STATE 3 OF THE 4 MONITORS HAD CORRODED TO THE POINT THEY SHOULD BE R…
Read full complaint
TIRE SENSOR CAME ON DURING DRIVE INTO WORK. MADE TO CALL DEALERSHIP TO HAVE IT CHECKED OUT BY LUNCH TIME THE REAR PASSENGER SIDE TIRE WAS COMPLETELY FLAT AND THE STEM OF THE TIRE PRESSURE MONITOR HAD COMPLETELY SNAPPED OFF. WHEN I GOT THE CAR TO A DEALER THEY STATE 3 OF THE 4 MONITORS HAD CORRODED TO THE POINT THEY SHOULD BE REPLACED. THIS ADDED NEARLY $400 DOLLARS TO GETTING THE TIRES ON THE CAR REPLACED. HOW IS IT A TIRE SENSOR CAN'T LAST AS LONG AS THE TIRES ON A BRAND NEW CAR? IF A TIRE SENSOR IS ADDED TO A CAR TO MAKE IT SAFER AND MORE EFFICIENT MAYBE IT SHOULD LAST MORE THAN 3 YEARS AND NOT CAUSE THE CAR TO BECOME UNSAFE. *TR
FACTORY TIRES (GOODYEAR RSA) WORE OUT IN <15K, EXCESSIVE INSIDE WEAR. REPLACED WITH BRIDGESTONE POTENZA GRID G019 205/50/R17. STARTED SHOWING INSIDE WEAR AROUND 45K, AND EXTREMELY LOUD ROAD NOISE AT 50K. ALL NEED TO BE REPLACED AGAIN. TIRES HAVE BEEN ROTATED AS PER WARRANTY REQUIREMENTS. ALIGNMENT IS FACTORY SPECIFICATIONS. CAR …
Read full complaint
FACTORY TIRES (GOODYEAR RSA) WORE OUT IN <15K, EXCESSIVE INSIDE WEAR. REPLACED WITH BRIDGESTONE POTENZA GRID G019 205/50/R17. STARTED SHOWING INSIDE WEAR AROUND 45K, AND EXTREMELY LOUD ROAD NOISE AT 50K. ALL NEED TO BE REPLACED AGAIN. TIRES HAVE BEEN ROTATED AS PER WARRANTY REQUIREMENTS. ALIGNMENT IS FACTORY SPECIFICATIONS. CAR HAS NEVER TOUCHED A TRACK AND IS USED AS A COMMUTER VEHICLE. ONLINE REPORTS HAVE BLAMED THE CAMBER WHICH IS NOT ADJUSTABLE ON THE MAZDA 3. SO THIS ISSUE WILL CONTINUE THROUGHOUT THE LIFE OF THE VEHICLE. SERIOUS DEFECT AND DANGEROUS. *TR
TIRE VALVE SPLIT AND ENTERED TIRE WELL CAUSING IT TO GO FLAT WHILE DRIVING AT 70MPH ON HIGHWAY. NOT ONLY DID I HAVE TO REPLACE THE TIRE VALVE 115.00 $ BUT I HAD TO REPLACE THE TIRE SINCE THE LITTLE WAYS THAT I DROVE ON IT TO PULL OVER SHREDDED THE INSIDE OF THE TIRE!!! THIS IS NOW THE SECOND VALVE THAT HAS BEEN REPLACED, LUCKILY…
Read full complaint
TIRE VALVE SPLIT AND ENTERED TIRE WELL CAUSING IT TO GO FLAT WHILE DRIVING AT 70MPH ON HIGHWAY. NOT ONLY DID I HAVE TO REPLACE THE TIRE VALVE 115.00 $ BUT I HAD TO REPLACE THE TIRE SINCE THE LITTLE WAYS THAT I DROVE ON IT TO PULL OVER SHREDDED THE INSIDE OF THE TIRE!!! THIS IS NOW THE SECOND VALVE THAT HAS BEEN REPLACED, LUCKILY THE FIRST WAS DISCOVERED BY THE MECHANIC WHILE REPLACING MY TIRES. THE OTHER TWO SEEM TO BE ON THERE WAY OUT AS WELL. *TR
2008 MAZDA 3 4-DOOR - TIRE PRESSURE MONITOR VALVE IS CORRODED AND SPLIT. A NUMBER OF COMPLAINTS ON-LINE ABOUT THIS SERIOUS SAFETY ISSUE. WILL CHECK IF WARRANTY COVERS REPLACEMENT TPM, BUT FROM READING OTHER COMPLAINTS, PROBABLY NOT! I AM AFRAID TO DRIVE THE CAR ON THE FREEWAY NOW. THE WARNING LIGHT GOES ON BECAUSE IT APPEAR…
Read full complaint
2008 MAZDA 3 4-DOOR - TIRE PRESSURE MONITOR VALVE IS CORRODED AND SPLIT. A NUMBER OF COMPLAINTS ON-LINE ABOUT THIS SERIOUS SAFETY ISSUE. WILL CHECK IF WARRANTY COVERS REPLACEMENT TPM, BUT FROM READING OTHER COMPLAINTS, PROBABLY NOT! I AM AFRAID TO DRIVE THE CAR ON THE FREEWAY NOW. THE WARNING LIGHT GOES ON BECAUSE IT APPEARS AIR IS LEAKING FROM THE VALVE STEM. MAZDA SHOULD RECALL ALL THESE POOR QUALITY TPM'S. *TR
TL* THE CONTACT OWNS A 2008 MAZDA MAZDA3. THE CONTACT WAS DRIVING 50 MPH IN RAINY WEATHER WHEN SHE ATTEMPTED TO ACTIVATE THE WINDSHIELD WIPERS, BUT THE WIPERS WOULD NOT TURN ON. THE VEHICLE WAS TAKEN TO AN AUTHORIZED DEALER WHERE THE GROUND HARNESS WAS REPLACED. APPROXIMATELY THREE MONTHS LATER, THE FAILURE RECURRED. THE VEHICLE…
Read full complaint
TL* THE CONTACT OWNS A 2008 MAZDA MAZDA3. THE CONTACT WAS DRIVING 50 MPH IN RAINY WEATHER WHEN SHE ATTEMPTED TO ACTIVATE THE WINDSHIELD WIPERS, BUT THE WIPERS WOULD NOT TURN ON. THE VEHICLE WAS TAKEN TO AN AUTHORIZED DEALER WHERE THE GROUND HARNESS WAS REPLACED. APPROXIMATELY THREE MONTHS LATER, THE FAILURE RECURRED. THE VEHICLE WAS TAKEN BACK TO HAVE THE FAILURE DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 30,000. UPDATED 01/13/12*LJ THE CONSUMER STATED A WIRE WAS FOUND NOT PROPERLY SECURED. UPDATED 01/19/12
ENGINE MOUNTS FAILED. NOTICED VIBRATION IN THE CABIN WHEN THE CAR WAS IN DRIVE. THERE WAS NO NOTICED VIBRATION WHEN THE CAR WAS IDLING. WHEN THE ENGINE WAS IN DRIVE, WITH THE HOOD POPPED, THE ENGINE WAS NOTICEABLY PITCHING FORWARD AND RETURNING TO IT'S DEFAULT POSITION WHEN THE GAS WAS RELEASED. I CHECKED RECALLS AND THERE W…
Read full complaint
ENGINE MOUNTS FAILED. NOTICED VIBRATION IN THE CABIN WHEN THE CAR WAS IN DRIVE. THERE WAS NO NOTICED VIBRATION WHEN THE CAR WAS IDLING. WHEN THE ENGINE WAS IN DRIVE, WITH THE HOOD POPPED, THE ENGINE WAS NOTICEABLY PITCHING FORWARD AND RETURNING TO IT'S DEFAULT POSITION WHEN THE GAS WAS RELEASED. I CHECKED RECALLS AND THERE WERE NONE SHOWN, BUT THERE WERE MANY COMPLAINTS ABOUT THIS ON THE INTERNET. LOCAL MECHANIC ALSO STATED THAT THIS IS A KNOWN. *TR
VEHICLE WAS TRAVELING IN LEFT LANE ON INTERSTATE AND SUDDENLY TURNED INTO CONCRETE DIVIDER. *TR
TL* THE CONTACT OWNS A 2008 MAZDA MAZDA3. WHILE DRIVING APPROXIMATELY 35 MPH, THE CONTACT EXPERIENCED A LOSS OF ELECTRONIC POWER STEERING ASSIST AND AS A RESULT, CRASHED INTO A CURB. THE VEHICLE WAS TOWED TO THE DEALER FOR DIAGNOSTICS WHERE THE TECHNICIANS ADVISED THE CONTACT OF NHTSA CAMPAIGN ID NUMBER: 10V374000 (STEERING:ELEC…
Read full complaint
TL* THE CONTACT OWNS A 2008 MAZDA MAZDA3. WHILE DRIVING APPROXIMATELY 35 MPH, THE CONTACT EXPERIENCED A LOSS OF ELECTRONIC POWER STEERING ASSIST AND AS A RESULT, CRASHED INTO A CURB. THE VEHICLE WAS TOWED TO THE DEALER FOR DIAGNOSTICS WHERE THE TECHNICIANS ADVISED THE CONTACT OF NHTSA CAMPAIGN ID NUMBER: 10V374000 (STEERING:ELECTRIC POWER ASSIST SYSTEM), WHICH THE VEHICLE WAS INCLUDED. THE TECHNICIAN AGREED TO REPAIR THE VEHICLE UNDER THE RECALL BUT WOULD NOT COVER THE REPAIRS FOR THE DAMAGE TO THE WHEEL DUE TO THE CRASH. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 25,000.
TL* THE CONTACT OWNS A 2008 MAZDA MAZDA3. THE CONTACT RECEIVED A RECALL NOTICE ASSOCIATED WITH NHTSA CAMPAIGN ID NUMBER 10V374000 (STEERING:ELECTRIC POWER ASSIST SYSTEM). AN AUTHORIZED DEALER WAS NOTIFIED AND THE CONTACT WAS INFORMED THAT THEY WERE WAITING ON THE NECESSARY PARTS TO ARRIVE BEFORE PERFORMING THE REPAIR. APPROXIMAT…
Read full complaint
TL* THE CONTACT OWNS A 2008 MAZDA MAZDA3. THE CONTACT RECEIVED A RECALL NOTICE ASSOCIATED WITH NHTSA CAMPAIGN ID NUMBER 10V374000 (STEERING:ELECTRIC POWER ASSIST SYSTEM). AN AUTHORIZED DEALER WAS NOTIFIED AND THE CONTACT WAS INFORMED THAT THEY WERE WAITING ON THE NECESSARY PARTS TO ARRIVE BEFORE PERFORMING THE REPAIR. APPROXIMATELY ONE YEAR LATER, THE CONTACT WAS STILL BEING INFORMED THAT THE PARTS WERE NOT AVAILABLE. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS UNKNOWN. THE VIN WAS UNAVAILABLE.
Official recalls
211V329000 · Visibility:windshield Wiper/washer:motor
Jun 15, 2011
MAZDA IS RECALLING CERTAIN MODEL YEAR 2008-2009 MAZDA3 AND MAZDASPEED3 VEHICLES MANUFACTURED FROM JANUARY 7, 2008, THROUGH NOVEMBER 28, 2008. THE GROUND TERMINAL OF THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN INADVERTENTLY BENT DURING ASSEMBLY. IF THIS CONDITION EXISTS THEN OVER TIME THE ELECTRICAL RESISTANCE OF THE MOTOR CIRCUIT MAY INCREASE UP TO A POINT THAT THE WINDSHIELD WIPERS WOULD NOT WORK.
Consequence & remedy
Consequence: THE LOSS OF WIPER FUNCTION IN ADVERSE WEATHER COULD POTENTIALLY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL INSTALL AN ADDITIONAL GROUND HARNESS ON THE WIPER MOTOR FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE JULY 15, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.