IllustrationMY TAIL LIGHTS HAVE MELTED THE RED PLASTIC COVER SEVERELY IN BOTH LIGHTS. MY FRIEND DRIVING BEHIND ME THOUGHT MY REVERSE LIGHTS WERE ON EVERY TIME I BRAKED. MY LIGHTS WERE THE ORIGINAL BULBS AND NOT AFTERMARKET. I DID NOT NOTICE THE MELTING UNTIL AUGUST 2014. *TR
2008 Mazda MAZDA3
Owner reports · Recalls · Investigations
More warning signs than most MAZDA3 years
Owner complaints for the 2008 Mazda MAZDA3 are substantially higher than the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
620–25K
8925–50K
4050–75K
3475–100K
25100–150K
6150K+
256 reports with mileage · 47 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 117 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Tires. Review the 41 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Wheels. Review the 33 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
29 crash reports1 fire reports16 injury reports
What owners actually said
303 reportsCOMPLETE ENGINE FAILURE ON WELL MAINTAINED MAZDA 3I AT 75000 MILES. TRAVELING ON FREEWAY IN SLOWEST LANE OF TRAFFIC, FIRST HEARD A CLICKING NOISE AND ENGINE LIGHT WENT ON. CAR SEEMED TO BE LOSING POWER. CALLED AAA ROADSIDE HELP, WHO CHECKED THE CAR AND DETERMINED IT WAS OK AND COULD BE DRIVEN HOME, ABOUT 10 MILES AWAY. P…
Read full complaint
COMPLETE ENGINE FAILURE ON WELL MAINTAINED MAZDA 3I AT 75000 MILES. TRAVELING ON FREEWAY IN SLOWEST LANE OF TRAFFIC, FIRST HEARD A CLICKING NOISE AND ENGINE LIGHT WENT ON. CAR SEEMED TO BE LOSING POWER. CALLED AAA ROADSIDE HELP, WHO CHECKED THE CAR AND DETERMINED IT WAS OK AND COULD BE DRIVEN HOME, ABOUT 10 MILES AWAY. PROCEEDED TO DRIVE HOME, 5 MILES INTO TRIP BEGAN LOSING POWER, CLICKING NOISE RETURNED SO I PULLED OVER TO SHOULDER AS CAR COMPLETELY LOST POWER, ENGINE OVERHEATED. PROGNOSIS: TIMING CHAIN BROKE, ENGINE OVERHEATED AND THIS CAR IS A TOTAL LOSS. FINDING NOW THERE ARE THOUSANDS OF CONSUMERS THAT HAVE EXPERIENCED THIS ISSUE WITH MAZDA ENGINES. THIS COMPANY IS A FRAUD, AND PEOPLE'S LIVES ARE IN DANGER AS THE RESULT. NEVER AGAIN WILL I HAVE ANYTHING TO DO WITH MAZDA CARS. *TR
TL * THE CONTACT OWNS A 2008 MAZDA3. WHILE DRIVING 65 MPH, THE STEERING WHEEL SUDDENLY SEIZED. THE CONTACT DEPRESSED THE BRAKE PEDAL, BUT THE BRAKES FAILED TO RESPOND. THE VEHICLE SPUN AND CRASHED INTO A GUARD RAIL. THE CONTACT WAS TRANSPORTED TO THE EMERGENCY ROOM BY AMBULANCE AND WAS TREATED FOR BRUISING, WHIPLASH, ACUTE N…
Read full complaint
TL * THE CONTACT OWNS A 2008 MAZDA3. WHILE DRIVING 65 MPH, THE STEERING WHEEL SUDDENLY SEIZED. THE CONTACT DEPRESSED THE BRAKE PEDAL, BUT THE BRAKES FAILED TO RESPOND. THE VEHICLE SPUN AND CRASHED INTO A GUARD RAIL. THE CONTACT WAS TRANSPORTED TO THE EMERGENCY ROOM BY AMBULANCE AND WAS TREATED FOR BRUISING, WHIPLASH, ACUTE NECK, BACK, SHOULDER, AND LEG TRAUMAS. THE MANUFACTURER WAS NOTIFIED AND STATED THAT THE VEHICLE WAS PREVIOUSLY REPAIRED ACCORDING TO NHTSA CAMPAIGN NUMBER: 10V374000 (STEERING). THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS UNKNOWN.
I WAS INFORMED BY MY FRIEND DRIVING IN BACK OF ME THAT MY BRAKE LIGHTS SEEMED TO BE MELTING AWAY, I LOOKED AT THE LIGHT AND REALIZED IT WAS THE LIGHT BULB MELTING THE COVER FOR THE BRAKE. I ASKED MAZDA WHAT WAS THE REASON BUT THEY DIDN'T LOOK INTO IT AND JUST ADVISED ME THE AMOUNT I WOULD NEED TO HAVE THIS FIXED BUT BECAUSE THE…
Read full complaint
I WAS INFORMED BY MY FRIEND DRIVING IN BACK OF ME THAT MY BRAKE LIGHTS SEEMED TO BE MELTING AWAY, I LOOKED AT THE LIGHT AND REALIZED IT WAS THE LIGHT BULB MELTING THE COVER FOR THE BRAKE. I ASKED MAZDA WHAT WAS THE REASON BUT THEY DIDN'T LOOK INTO IT AND JUST ADVISED ME THE AMOUNT I WOULD NEED TO HAVE THIS FIXED BUT BECAUSE THEY ADVISED ME THAT I HAVE TO PAY FOR THIS DAMAGE THAT LOOKS LIKE A MANUFACTURER DAMAGE, I JUST LEFT IT ALONE UNTIL THE LIGHT BULB WENT OUT AND I HAVE TO BE VERY CAREFUL TO REPLACE IT NOT TO GET HURT FROM IT. AS 1 MONTH PASSED, I REALIZED THAT THE COVER WAS MELTING AWAY AND IT LOOKED JUST LIKE A BACKUP LIGHT AND ALSO REALIZED THAT MY RIGHT SIDE WAS DOING THE SAME. I THOUGHT IT THIS RED COVER WEARS AWAY, THIS CAN BE DANGEROUS FOR THE DRIVERS IN BACK OF ME THAT WOULD ONLY PAY ATTENTION TO THE RED LIGHTS WHEN I HIT THE BRAKE. THIS MAY BE A HAZARD ON THE ROAD AND LEAD TO ACCIDENTS IF DRIVERS WERE NOT PAYING CLOSE ATTENTION THAT MY BRAKE LIGHT WAS NO LONGER RED. I THEN STARTED DOING RESEARCH AND NOTICED ON THE MAZDA FORUM THAT MANY OTHERS HAD THE SAME SITUATION AS ME, HOPEFULLY YOU CAN LOOK INTO IT. *JS
IN THE PAST MONTH THE RADIO, LIGHTS, THE CLUSTER, ALL SHUT DOWN AND RESTART AS DRIVING. LAST NIGHT AS DRIVING ON TELEGRAPH RD, 45 MPH, THE POWER STEERING SUDDENLY STOPPED WORKING, I COULD NOT CONTROL THE CAR, AND ANOTHER VEHICLE BEHIND ME ALMOST HIT ME, AS I WAS SWITCHING IN NEUTRAL, AND BACK IN DRIVE. ALL OF THE SUDDEN REGAIN C…
Read full complaint
IN THE PAST MONTH THE RADIO, LIGHTS, THE CLUSTER, ALL SHUT DOWN AND RESTART AS DRIVING. LAST NIGHT AS DRIVING ON TELEGRAPH RD, 45 MPH, THE POWER STEERING SUDDENLY STOPPED WORKING, I COULD NOT CONTROL THE CAR, AND ANOTHER VEHICLE BEHIND ME ALMOST HIT ME, AS I WAS SWITCHING IN NEUTRAL, AND BACK IN DRIVE. ALL OF THE SUDDEN REGAIN CONTROL AND WAS ABLE TO TURN RIGHT INTO A PARKING LOT. I REMEMBER HAVING THIS ISSUE BACK IN JAN. OF 2011, AND THERE WAS A RECALL FOR IT, THAT I HAVE HAD FIXED. THE PATTERN IS THAT I BOUGHT THE VEHICLE IN 2008, 3 YEARS LATER - IN 2011 THE RECALL TOOK CARE OF THE DEFECTIVE PART, AND NOW, 3 YEARS AFTER THE REPLACEMENT THE SAME ISSUE ARISE. THIS IS VERY DANGEROUS, CAN CAUSE ACCIDENTS, AS IS HAPPENS AS DRIVING UNEXPECTEDLY. *TR
ABOUT A YEAR AGO I BOUGHT 4 NEW TIRES FOR MY MAZDA 3. SIX MONTHS LATER I WENT IN FOR MY ROUTINE ALIGNMENT AND TIRE ROTATION. THEY SAID MY TWO REAR TIRES WERE WORN DOWN TO SHOWING THE WIRING AND COULD POTENTIALLY CAUSE A BLOW OUT. THEY REFUSED TO PUT THE TIRES BACK ON FOR SAFETY CONCERNS. I HAD TO PURCHASE TWO USED TIRES THAT…
Read full complaint
ABOUT A YEAR AGO I BOUGHT 4 NEW TIRES FOR MY MAZDA 3. SIX MONTHS LATER I WENT IN FOR MY ROUTINE ALIGNMENT AND TIRE ROTATION. THEY SAID MY TWO REAR TIRES WERE WORN DOWN TO SHOWING THE WIRING AND COULD POTENTIALLY CAUSE A BLOW OUT. THEY REFUSED TO PUT THE TIRES BACK ON FOR SAFETY CONCERNS. I HAD TO PURCHASE TWO USED TIRES THAT HAD ABOUT THE SAME MILEAGE MY OTHER TIRES HAD ON THEM. AGAIN 5-6 MONTHS LATER I GO INTO LES SCHWAB FOR MY TIRE ROTATION AND ALIGNMENT AND AGAIN THEY TELL ME MY TWO REAR TIRES ARE SHOWING EXCESSIVE WEAR. WHEN COMPLAINING ABOUT HAVING TO GET TIRES SO SOON THEY STATED THAT MAZDA DESIGNED THE CAR THIS WAY TO HAVE A TOE IN ALIGNMENT. BASICALLY THIS WILL BE A RECURRING ISSUE UNLESS I PUT A $500 CAMBER KIT ON THE BACK. WHEN I ASKED ABOUT THAT THEY SAID IT MAY CHANGE THE WAY THE CAR HANDLES AND HAVE LOUDER ROAD NOISE. NONE OF THIS WAS MENTIONED BY MAZDA WHEN I PURCHASED THAT CAR BACK IN 2008. NOT ONLY IS THIS ISSUE CAUSING ME TO SPEND MONEY EVERY 5-6 MONTHS BUT IF I WERE TO GO TO LONG WITHOUT CHECKING MY TIRES I COULD HAVE A BLOWOUT WHILE DRIVING, POSSIBLY CAUSING AN ACCIDENT, INJURY OR DEATH. I SEE THIS AS BEING A VERY BIG ISSUE WITH THE MAZDA AND I WOULD LIKE TO SEE MAZDA HAVE TO RECALL AND FIX THIS PROBLEM. *TR
THE RED PLASTIC ON MY TAIL LIGHT HAS MELTED. I ASSUME THAT THIS COULD HAVE AT SOME POINT CREATED A FIRE OR SOME OTHER SAFETY HAZARD. THERE ARE MANY COMPLAINTS ABOUT THIS VERY PROBLEM IN THIS MAKE AND MODEL CAR AND THIS NEEDS TO BE ADDRESSED BY MAZDA EVEN IF THE CAR IS NO LONGER UNDER WARRANTY. THIS IS A SAFETY ISSUE AND I BEL…
Read full complaint
THE RED PLASTIC ON MY TAIL LIGHT HAS MELTED. I ASSUME THAT THIS COULD HAVE AT SOME POINT CREATED A FIRE OR SOME OTHER SAFETY HAZARD. THERE ARE MANY COMPLAINTS ABOUT THIS VERY PROBLEM IN THIS MAKE AND MODEL CAR AND THIS NEEDS TO BE ADDRESSED BY MAZDA EVEN IF THE CAR IS NO LONGER UNDER WARRANTY. THIS IS A SAFETY ISSUE AND I BELIEVE THE GOVERNMENT SHOULD TAKE THIS SERIOUSLY AND MOVE TO ACTION AGAINST MAZDA FOR THIS FLAW IN THEIR MANUFACTURING. WE ARE NOW HAVING TO REPLACE THIS PART AND IT WILL COST ABOUT $600.00. *TR
TPMS LIGHT ALERTED LOW TIRE PRESSURE CONDITION. FOUND TIRE WITH LOW PRESSURE. DURING INSPECTION OF TIRE, A SMALL AIR LEAK WAS DISCOVERED AT THE VALVE STEM MID SECTION OF THREADS DUE TO CORROSION. THE TPMS SENSOR ASSEMBLY REPLACEMENT WAS NECESSARY TO CORRECT THE FAILURE. APPROXIMATELY EIGHTEEN MONTHS AFTERWARDS, THE SAME E…
Read full complaint
TPMS LIGHT ALERTED LOW TIRE PRESSURE CONDITION. FOUND TIRE WITH LOW PRESSURE. DURING INSPECTION OF TIRE, A SMALL AIR LEAK WAS DISCOVERED AT THE VALVE STEM MID SECTION OF THREADS DUE TO CORROSION. THE TPMS SENSOR ASSEMBLY REPLACEMENT WAS NECESSARY TO CORRECT THE FAILURE. APPROXIMATELY EIGHTEEN MONTHS AFTERWARDS, THE SAME EXACT FAILURE RE-OCCURRED IN ANOTHER TPMS SENSOR. THE ALUMINUM ALLOY VALVE STEMS ON THESE SENSORS ARE HIGHLY SUSCEPTIBLE TO CORROSION DAMAGE AND NEED TO BE RE-CALLED. THIS FAILURE IS A COMMON PROBLEM WITH THESE SENSORS, ESPECIALLY WHERE VEHICLES EQUIPPED WITH THESE ARE DRIVEN WHERE ROAD "SALTING" IS ROUTINE. THE POTENTIALLY DANGEROUS LOW TIRE PRESSURE CONDITION CAUSED BY THESE FAULTY STEMS MAY LEAD TO AN ACCIDENT RESULTING IN DEATH. *TR
THE TIRE PRESSURE MONITORING SYSTEM SEEMS TO BE OVERSENSITIVE THE WARNING LIGHT STAYS ON EVEN WHEN THE TIRES ARE PROPERLY INFLATED. *TR
I PARKED MY CAR ON NUMEROUS OCCASIONS IN THE LAST FEW MONTHS WHERE THE TRANSMISSION FAILED TO ENGAGE IN PARK. IT REQUIRED MULTIPLE TRIES TO GET THE PARK INDICATOR LIGHT ON THE DASH TO REFLECT THAT THE CAR WAS SAFELY ENGAGED IN PARK. BEFORE I REALIZED WHAT WAS HAPPENING WITH THE TRANSMISSION. ON AT LEAST 3 OCCASIONS I WAS UNABLE …
Read full complaint
I PARKED MY CAR ON NUMEROUS OCCASIONS IN THE LAST FEW MONTHS WHERE THE TRANSMISSION FAILED TO ENGAGE IN PARK. IT REQUIRED MULTIPLE TRIES TO GET THE PARK INDICATOR LIGHT ON THE DASH TO REFLECT THAT THE CAR WAS SAFELY ENGAGED IN PARK. BEFORE I REALIZED WHAT WAS HAPPENING WITH THE TRANSMISSION. ON AT LEAST 3 OCCASIONS I WAS UNABLE TO START MY CAR AT ALL WHEN I RETURNED FROM A BRIEF STOP. THE PROBLEM WITH FAILING TO START HAPPENED WHEN THE CAR WAS ON A SLIGHT INCLINE AND I HAD ENGAGED THE PARKING BRAKE. AFTER JIGGLING THE AUTOMATIC TRANSMISSION LEVER REPEATEDLY, MOVING THE STEERING WHEEL AND APPLYING THE BRAKE VIGOROUSLY, I WAS EVENTUALLY ABLE TO GET THE CAR TO START. I'M NOT SURE WHETHER IT WAS ROCKING OF THE VEHICLE FROM FRUSTRATION OR JIGGLING THE GEAR SELECTOR THAT FINALLY WORKED. THE CAR HAS A NEW BATTERY AND HAS HAD ALL SCHEDULED MAINTENANCE PERFORMED BY MY LOCAL MAZDA DEALER. WHEN THIS HAPPENS, OTHER ELECTRICAL EQUIPMENT FUNCTIONS BUT THERE IS ABSOLUTELY NO RESPONSE FROM THE IGNITION SYSTEM. *TR
Official recalls
211V329000 · Visibility:windshield Wiper/washer:motor
Jun 15, 2011
MAZDA IS RECALLING CERTAIN MODEL YEAR 2008-2009 MAZDA3 AND MAZDASPEED3 VEHICLES MANUFACTURED FROM JANUARY 7, 2008, THROUGH NOVEMBER 28, 2008. THE GROUND TERMINAL OF THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN INADVERTENTLY BENT DURING ASSEMBLY. IF THIS CONDITION EXISTS THEN OVER TIME THE ELECTRICAL RESISTANCE OF THE MOTOR CIRCUIT MAY INCREASE UP TO A POINT THAT THE WINDSHIELD WIPERS WOULD NOT WORK.
Consequence & remedy
Consequence: THE LOSS OF WIPER FUNCTION IN ADVERSE WEATHER COULD POTENTIALLY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL INSTALL AN ADDITIONAL GROUND HARNESS ON THE WIPER MOTOR FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE JULY 15, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.