IllustrationThe power steering on my 2008 Mazda 3 went out. I took it to a mechanic shop who diagnosed the power steering pump is creating pressure that is getting to the rack and pinion and the fluid is just bouncing off of the rack and pinion and the computer system does not know how to function, so the power steering is not working.
2008 Mazda MAZDA3
Owner reports · Recalls · Investigations
More warning signs than most MAZDA3 years
Owner complaints for the 2008 Mazda MAZDA3 are substantially higher than the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
620–25K
8925–50K
4050–75K
3475–100K
25100–150K
6150K+
256 reports with mileage · 47 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 117 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Tires. Review the 41 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Wheels. Review the 33 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
29 crash reports1 fire reports16 injury reports
What owners actually said
303 reportsThere is a plastic ring on top of the gas tank that holds down the fuel pump.I filled up my tank and looked under the car afterwards,at this time I noticed gas coming out from the tank until is was flushed with the top and then stopped.I pulled out the back seat,found the inspection plate and for sure this was and did happen,no…
Read full complaint
There is a plastic ring on top of the gas tank that holds down the fuel pump.I filled up my tank and looked under the car afterwards,at this time I noticed gas coming out from the tank until is was flushed with the top and then stopped.I pulled out the back seat,found the inspection plate and for sure this was and did happen,now nothing could be done at the time because the inspection plat hole was smaller than the ring,the tank had to be dropped.It had to be fixed,about $600.00 later and tank filled up it was repaired.I still have the ring and pictures where the ring was cracked around the threads.send me a e-mail address and I can send pictures and a copy of the bill.later on I went on line and discovered that I was not the only one.This happen about 2 years back.
Transmission control module.
Drivers side lower control arm failed at the lower ball joint mounting hole, allowing the ball joint to separate from the arm. All vehicle steering and control was lost due to the failure. This failure: 1. Has extreme danger for traffic fatalities. 2. Suggests substandard materials, design, or manufacturing. Control arm manufac…
Read full complaint
Drivers side lower control arm failed at the lower ball joint mounting hole, allowing the ball joint to separate from the arm. All vehicle steering and control was lost due to the failure. This failure: 1. Has extreme danger for traffic fatalities. 2. Suggests substandard materials, design, or manufacturing. Control arm manufacturer: DLZ Sold by: partsgoing Vendor: Amazon.com
2008 MAZDA 3. CONSUMER WRITES IN REGARDS TO DEFECTIVE FUEL PUMP.
TL* THE CONTACT OWNS A 2008 MAZDA MAZDA3. THE CONTACT STATED THAT THE VEHICLE EXPERIENCED LOSS OF POWER STEERING ASSIST WHILE DRIVING AT VARIOUS SPEED AND MAKING TURN. THE POWER STEERING FAILED AND THE STEERING WHEEL BECAME DIFFICULT TO TURN. THE PARKING BRAKE AND POWER STEERING ASSIST WARNING LIGHTS WERE ILLUMINATED. THE CONTAC…
Read full complaint
TL* THE CONTACT OWNS A 2008 MAZDA MAZDA3. THE CONTACT STATED THAT THE VEHICLE EXPERIENCED LOSS OF POWER STEERING ASSIST WHILE DRIVING AT VARIOUS SPEED AND MAKING TURN. THE POWER STEERING FAILED AND THE STEERING WHEEL BECAME DIFFICULT TO TURN. THE PARKING BRAKE AND POWER STEERING ASSIST WARNING LIGHTS WERE ILLUMINATED. THE CONTACT STATED THAT THE FAILURE OCCURRED FIVE TIMES IN TWO DAYS. THE CONTACT MENTIONED THAT AN UNKNOWN RECALL REPAIR WAS COMPLETED ON THE VEHICLE FOR THE POWER STEERING, HOWEVER THE REPAIR HAD NOT CORRECTED THE FAILURE. THE VEHICLE WAS NOT TAKEN TO A DEALER OR AN INDEPENDENT MECHANIC FOR DIAGNOSTIC TESTING. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND INFORMED THE CONTACT THAT A RECALL REPAIR WAS COMPLETED FOR THE SAME FAILURE AND IT WAS A ONE-TIME FREE FIX AND PROVIDED A CASE NUMBER. THE FAILURE MILEAGE WAS APPROXIMATELY 90,000.
MY MAZDA3 DIES WHILE I AM DRIVING WITHOUT ANY INDICATION OF WHAT IS GOING ON (NO CHECK ENGINE LIGHT). WHEN IT DOES, I WAIT FOR A WHILE AND IT WILL START BACK UP AGAIN! MY SHOP AND I HAVE TRIED EVERYTHING WE CAN, BUT WE CAN'T FIGURE OUT WHY IT IS DOING THAT! I CALLED THE MANUFACTURE AND THEY SAID IT WAS RECALLED FOR POWER STE…
Read full complaint
MY MAZDA3 DIES WHILE I AM DRIVING WITHOUT ANY INDICATION OF WHAT IS GOING ON (NO CHECK ENGINE LIGHT). WHEN IT DOES, I WAIT FOR A WHILE AND IT WILL START BACK UP AGAIN! MY SHOP AND I HAVE TRIED EVERYTHING WE CAN, BUT WE CAN'T FIGURE OUT WHY IT IS DOING THAT! I CALLED THE MANUFACTURE AND THEY SAID IT WAS RECALLED FOR POWER STEERING ASSIST FAILURE AND FIXED IN 2010 BUT TO US IT SOUNDS IT IS THAT ISSUE CAUSING IT TO STOP WHILE IN MOTION! THIS CAR IS UNSAFE!! NO CAR SHOULD STOP IN MOTION FROM NOWHERE! THE MANUFACTURE SHOULD BE RESPONSIBLE FOR THAT!
AIRBAG LIGHT IS ON.....LOST POWER STEERING AT ONLY 110,000 MILES...ABS BREAK SYSTEM NOT WORKING
AT AND YELLOW CHECK ENGINE LIGHT CAME ON AND CAR WAS IN LIMP MODE FIRST THING IN MORNING AFTER HAVING NO ISSUES WITH MY MAZDA PREVIOUSLY. CODES CAME BACK WITH SOLENOIDS A, B, C, D, E ALL HAVE ELECTRICAL FAILURE, AND ISSUES WITH THE OXYGEN SENSOR. MY CAR HAS HAD REGULAR MAINTENANCE DONE ON IT. NO SIGNS OR SYMPTOMS OF TRANSMISSION…
Read full complaint
AT AND YELLOW CHECK ENGINE LIGHT CAME ON AND CAR WAS IN LIMP MODE FIRST THING IN MORNING AFTER HAVING NO ISSUES WITH MY MAZDA PREVIOUSLY. CODES CAME BACK WITH SOLENOIDS A, B, C, D, E ALL HAVE ELECTRICAL FAILURE, AND ISSUES WITH THE OXYGEN SENSOR. MY CAR HAS HAD REGULAR MAINTENANCE DONE ON IT. NO SIGNS OR SYMPTOMS OF TRANSMISSION FAILURE BEFOREHAND. HAPPENED INSTANTLY OVERNIGHT. TCM IS NOT IN STOCK ANYWHERE AND I SUSPECT THAT IS THE CULPRIT DUE TO OTHER MAZDA OWNERS SIMILAR SITUATIONS. 95K MILES.
BRAKES BECAME SPONGY AFTER HARD BRAKING AT INTERSTATE HIGHWAY SPEED OF 65 MPH. AFTERWARD, SPORADICALLY, BRAKES WOULD REQUIRE SEVERAL PUMPS OF THE PEDAL TO BUILD ENOUGH HYDRAULIC PRESSURE TO STOP THE VEHICLE. I'M REPORTING THIS INCIDENT NOW AFTER LEARNING ABOUT FORD RECALL 19S54, NHTSA IDENTIFIER 19V904. BRAKE PARTS ON THIS CA…
Read full complaint
BRAKES BECAME SPONGY AFTER HARD BRAKING AT INTERSTATE HIGHWAY SPEED OF 65 MPH. AFTERWARD, SPORADICALLY, BRAKES WOULD REQUIRE SEVERAL PUMPS OF THE PEDAL TO BUILD ENOUGH HYDRAULIC PRESSURE TO STOP THE VEHICLE. I'M REPORTING THIS INCIDENT NOW AFTER LEARNING ABOUT FORD RECALL 19S54, NHTSA IDENTIFIER 19V904. BRAKE PARTS ON THIS CAR WERE MADE BY FOMOCO. ABS HYDRAULIC UNIT, P/N BVSN-43-7AZD, WAS REPLACED BY MAZDA DEALER TO CORRECT PROBLEM AT A COST OF $1200.
Official recalls
211V329000 · Visibility:windshield Wiper/washer:motor
Jun 15, 2011
MAZDA IS RECALLING CERTAIN MODEL YEAR 2008-2009 MAZDA3 AND MAZDASPEED3 VEHICLES MANUFACTURED FROM JANUARY 7, 2008, THROUGH NOVEMBER 28, 2008. THE GROUND TERMINAL OF THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN INADVERTENTLY BENT DURING ASSEMBLY. IF THIS CONDITION EXISTS THEN OVER TIME THE ELECTRICAL RESISTANCE OF THE MOTOR CIRCUIT MAY INCREASE UP TO A POINT THAT THE WINDSHIELD WIPERS WOULD NOT WORK.
Consequence & remedy
Consequence: THE LOSS OF WIPER FUNCTION IN ADVERSE WEATHER COULD POTENTIALLY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL INSTALL AN ADDITIONAL GROUND HARNESS ON THE WIPER MOTOR FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE JULY 15, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.