IllustrationBRAKE ROTORS WARP EARLY ON 2008 MAZDA 3 CAUSING EXCESSIVE VIBRATION WHEN BRAKING OVER 45 MPH AND CAUSES THE STEERING WHEEL TO SHAKE. *TR
2008 Mazda MAZDA3
Owner reports · Recalls · Investigations
More warning signs than most MAZDA3 years
Owner complaints for the 2008 Mazda MAZDA3 are substantially higher than the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
620–25K
8925–50K
4050–75K
3475–100K
25100–150K
6150K+
256 reports with mileage · 47 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 117 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Tires. Review the 41 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Wheels. Review the 33 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
29 crash reports1 fire reports16 injury reports
Service Brakes, Hydraulic complaints
6 reportsFIRST INCIDENT OCCURRED AT 25,900 MILES; BRAKE WARNING LIGHT APPEARED ON CONSOLE DASH. DEALER IDENTIFIED A FAILURE OF THE ABS (ANTI-LOCK BRAKE SYSTEM) MODULE WHICH WAS LEAKING BRAKE FLUID. DEALER REPLACED ABS MODULE UNDER WARRANTY. SECOND OCCURRENCE AT 37,600 MILES; BRAKE, ABS, AND TRACTION CONTROL WARNING LIGHTS APPEARED ON …
Read full complaint
FIRST INCIDENT OCCURRED AT 25,900 MILES; BRAKE WARNING LIGHT APPEARED ON CONSOLE DASH. DEALER IDENTIFIED A FAILURE OF THE ABS (ANTI-LOCK BRAKE SYSTEM) MODULE WHICH WAS LEAKING BRAKE FLUID. DEALER REPLACED ABS MODULE UNDER WARRANTY. SECOND OCCURRENCE AT 37,600 MILES; BRAKE, ABS, AND TRACTION CONTROL WARNING LIGHTS APPEARED ON DASH. DEALER IDENTIFIED FAILURE OF THE ABS MODULE WHICH HAD STOPPED COMMUNICATING WITH THE PCM. AS A RESULT OF THIS SECOND FAILURE, THE ABS AND/OR TRACTION CONTROL SYSTEM WAS NOT FUNCTIONING NORMALLY. DEALER COULD NOT IDENTIFY A ROOT CAUSE FOR THE CONSECUTIVE FAILURES OF THE ABS MODULE. COST TO REPLACE THE ABS MODULE WAS QUOTED BY DEALER AT APPROXIMATELY $1,600.00 (PART + LABOR). UPDATED PORTABLE 02/24/11
WHILE TURNING THROUGH AN INTERSECTION ON AN EXTREMELY COLD DAY (BELOW -10 DEGREES FAHRENHEIT) DRIVER DEPRESSES BRAKES ON AN ICY SURFACE. ANT-ILOCK BRAKING SYSTEM FAILS AND VEHICLE BEGINS TO HANDLE UNEXPECTEDLY. BRAKE WARNING LIGHT AND ABS WARNING LIGHT ILLUMINATE. AFTER ~2 MILES OF DRIVING, SYSTEM STILL INACTIVE. DRIVER PU…
Read full complaint
WHILE TURNING THROUGH AN INTERSECTION ON AN EXTREMELY COLD DAY (BELOW -10 DEGREES FAHRENHEIT) DRIVER DEPRESSES BRAKES ON AN ICY SURFACE. ANT-ILOCK BRAKING SYSTEM FAILS AND VEHICLE BEGINS TO HANDLE UNEXPECTEDLY. BRAKE WARNING LIGHT AND ABS WARNING LIGHT ILLUMINATE. AFTER ~2 MILES OF DRIVING, SYSTEM STILL INACTIVE. DRIVER PULLS OVER AND SHUTS OFF VEHICLE FOR 30 SECONDS. WHEN VEHICLE IS RESTARTED, ONLY THE ABS WARNING LIGHT STILL ACTIVE. AFTER BRAKING IN SAFE LOCATION, ABS SYSTEM ACTIVATES, AND WARNING LIGHT GOES OFF. DEALER INVESTIGATION STATES THAT THE MALFUNCTION IS LIKELY CAUSED BY EXTREME LOW TEMPERATURES. NO CORRECTIVE ACTION TAKEN. *TR
I OWN A 2008 MAZDA 3. ON THIS PARTICULAR MODE OF MAZDA THE BRAKE AND GAS PEDALS ARE LESS THAN 1/4 INCH FROM EACH OTHER. I HAVE BEEN IN NUMEROUS NEAR MISSES WITH SEVERAL CARS, THE MOST RECENT BEING TODAY BECAUSE ALOT OF TIMES WHEN YOU GO TO STEP ON THE BRAKE PEDAL YOU GET THE GAS AT THE SAME TIME BECAUSE THEY ARE SO CLOSE TOGET…
Read full complaint
I OWN A 2008 MAZDA 3. ON THIS PARTICULAR MODE OF MAZDA THE BRAKE AND GAS PEDALS ARE LESS THAN 1/4 INCH FROM EACH OTHER. I HAVE BEEN IN NUMEROUS NEAR MISSES WITH SEVERAL CARS, THE MOST RECENT BEING TODAY BECAUSE ALOT OF TIMES WHEN YOU GO TO STEP ON THE BRAKE PEDAL YOU GET THE GAS AT THE SAME TIME BECAUSE THEY ARE SO CLOSE TOGETHER. *TR
WHILE DRIVING ON THE FREEWAY AT 75 MPH, TRIED TO AVOID A VEHICLE THAT WAS UNSAFELY CHANGING LANES. PUSHED BRAKES AND VEERED TOWARDS LEFT. THE BRAKES (WHICH ARE NOT ABS) RESPONDED SLOWLY AND I SLAMMED IN THE MIDDLE DIVIDER. A COUPLE MONTH BEFORE THE ACCIDENT THE DEALER HAD THE ROTORS RESURFACED SINCE THE CAR WAS SHAKING VIGOROUSL…
Read full complaint
WHILE DRIVING ON THE FREEWAY AT 75 MPH, TRIED TO AVOID A VEHICLE THAT WAS UNSAFELY CHANGING LANES. PUSHED BRAKES AND VEERED TOWARDS LEFT. THE BRAKES (WHICH ARE NOT ABS) RESPONDED SLOWLY AND I SLAMMED IN THE MIDDLE DIVIDER. A COUPLE MONTH BEFORE THE ACCIDENT THE DEALER HAD THE ROTORS RESURFACED SINCE THE CAR WAS SHAKING VIGOROUSLY WHILE BRAKING AT HIGH SPEEDS. ALSO THE AIR BAGS DID NOT DEPLOY DURING THE ACCIDENT. TOOK CAR TO A MECHANIC AND THE MECHANIC WAS AMAZED THAT BASED ON THE VISUAL FRONTAL DAMAGE TO THE CAR THE AIR BAGS DID NOT DEPLOY. *TR
AFTER DRIVING ON SNOW COVERED ROAD, ABS WARNING LIGHT COMES ON AND ABS IS NON-OPERATIONAL. THE ABS WOULD RESUME FUNCTION AFTER AT LEAST 30-45 MIN OF DRIVING. DEALER STATED THAT SNOW BECAME TRAPPED IN ABS SENSOR BUT PROBLEM CANNOT BE RESOLVED. ABS FAILURE OCCURRED 3-4 TIMES OVER THE PAST WINTER WHEN ABS WAS ESSENTIAL. *TR
Official recalls
211V329000 · Visibility:windshield Wiper/washer:motor
Jun 15, 2011
MAZDA IS RECALLING CERTAIN MODEL YEAR 2008-2009 MAZDA3 AND MAZDASPEED3 VEHICLES MANUFACTURED FROM JANUARY 7, 2008, THROUGH NOVEMBER 28, 2008. THE GROUND TERMINAL OF THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN INADVERTENTLY BENT DURING ASSEMBLY. IF THIS CONDITION EXISTS THEN OVER TIME THE ELECTRICAL RESISTANCE OF THE MOTOR CIRCUIT MAY INCREASE UP TO A POINT THAT THE WINDSHIELD WIPERS WOULD NOT WORK.
Consequence & remedy
Consequence: THE LOSS OF WIPER FUNCTION IN ADVERSE WEATHER COULD POTENTIALLY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL INSTALL AN ADDITIONAL GROUND HARNESS ON THE WIPER MOTOR FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE JULY 15, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.