IllustrationLOW TIRE PRESSURE LIGHT CAME ON. FOUND VALVE STEM CRACKED AND LEAKING AIR FROM ITS SIDE. HAS HAPPENED TO TWO DIFFERENT VALVE STEMS. SOUTHERN CAR NEVER EXPOSED TO SALT. VALVE STEMS LOOK NEW. TIRE STORE CHARGES OVER $200 TO REPLACE EACH ONE. *TR
2007 Mazda MAZDA3
Owner reports · Recalls · Investigations
More warning signs than most MAZDA3 years
Owner complaints for the 2007 Mazda MAZDA3 are substantially higher than the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
270–25K
3325–50K
3250–75K
3475–100K
39100–150K
18150K+
183 reports with mileage · 39 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 89 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 36 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 22 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
28 crash reports3 fire reports16 injury reports
What owners actually said
222 reportsDRIVING AND LOST POWER STEERING INDICATOR LIGHT WENT ON, ABS, LIGHT CAME ON LOST POWER ON RADIO AND DASH, CALLED DEALER AND FOUND NO RECALLS , CALLED MAZDA THEY SAID VIN DOES NOT SHOW RECALLS . THIS IS A MAJOR SAFETY CONCERN AND MAZDA SHOULD FIX THIS AS WELL AS OTHERS. *JB
I WAS MAKING A TURN AND MY VEHICLE HAD SUDDENLY BECOME VERY DIFFICULT TO STEER. HAPPENED TWICE THAT DAY AND WHEN I PARKED, MY VEHICLE SHUT OFF. I TOOK IT IN TO GET IT CHECKED AND WAS INFORMED THERE WAS A SAFETY RECALL FOR POWER STEERING ISSUES ON MAZDA 3 2007-2009. I CALLED MAZDA CUSTOMER SERVICE AND WAS INFORMED MY VEHICLE V…
Read full complaint
I WAS MAKING A TURN AND MY VEHICLE HAD SUDDENLY BECOME VERY DIFFICULT TO STEER. HAPPENED TWICE THAT DAY AND WHEN I PARKED, MY VEHICLE SHUT OFF. I TOOK IT IN TO GET IT CHECKED AND WAS INFORMED THERE WAS A SAFETY RECALL FOR POWER STEERING ISSUES ON MAZDA 3 2007-2009. I CALLED MAZDA CUSTOMER SERVICE AND WAS INFORMED MY VEHICLE VIN DID NOT FALL UNDER THE RECALL AND THAT THEY WOULD NOT REPAIR MY VEHICLE UNLESS IT WAS AT MY OWN EXPENSE. MAZDA ONLY RECALLS SPECIFIC VEHICLES AND NOT ALL. *TR
I HAVE CONSTANTLY REPLACED MY DRIVER WINDOW MOTOR. THE DRIVER WINDOW SWITCH/MOTOR STOPS WORKING FOR NO REASON. IN ADDITION THE ENTIRE HEADUNIT STOPS WORKING. IT SHUTS ON AND OFF WHILE IN THE MIDDLE OF DRIVING. SOMETIMES TO POWERS RIGHT BACK ON AND OTHER TIMES IT CAN TAKE DAYS FOR IT TO TURN BACK ON. *TR
TL* THE CONTACT OWNS A 2007 MAZDA MAZDA3. THE CONTACT STATED THAT WHILE DRIVING 55 MPH, THE STEERING WHEEL BECAME DIFFICULT TO MANEUVER. IN ADDITION, THE VEHICLE BEGAN STUTTERING AND MISFIRING. THE VEHICLE WAS TOWED TO AN INDEPENDENT MECHANIC FOR DIAGNOSIS AND THE CONTACT WAS INFORMED THAT THE FUEL PUMP WOULD NEED TO BE REPLACED…
Read full complaint
TL* THE CONTACT OWNS A 2007 MAZDA MAZDA3. THE CONTACT STATED THAT WHILE DRIVING 55 MPH, THE STEERING WHEEL BECAME DIFFICULT TO MANEUVER. IN ADDITION, THE VEHICLE BEGAN STUTTERING AND MISFIRING. THE VEHICLE WAS TOWED TO AN INDEPENDENT MECHANIC FOR DIAGNOSIS AND THE CONTACT WAS INFORMED THAT THE FUEL PUMP WOULD NEED TO BE REPLACED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE VEHICLE HAD NOT BEEN REPLACED. THE FAILURE AND CURRENT MILEAGE WAS 108,000.
DROVE VEHICLE A SHORT DISTANCE, PARKED & SHUT OFF ENGINE. STARTED ENGINE A SHORT TIME LATER AND AS SOON AS I TURNED THE STEERING WHEEL THE POWER STEERING ASSIST MALFUNCTION LAMP TURNED ON AND THE WHEEL COULD NOT BE TURNED WITH REASONABLE EFFORT (CAR WAS STILL STOPPED). *TR
MY HUSBAND WAS DRIVING TO WORK WHEN HE EXPERIENCED A PROBLEM WITH THE POWER STEERING, IT BECAME VERY HARD TO STEER. HE MADE IT TO WORK, AND THE MAZDA CONTINUES TO HAVE POWER STEERING ISSUES. TODAY 5/11/13, A FRIEND INFORMED US THAT THERE IS A MAZDA 3 2007 POWER STEERING RECALL. I AM UPSET THAT MAZDA NEVER SENT ME ANY INFORMATIO…
Read full complaint
MY HUSBAND WAS DRIVING TO WORK WHEN HE EXPERIENCED A PROBLEM WITH THE POWER STEERING, IT BECAME VERY HARD TO STEER. HE MADE IT TO WORK, AND THE MAZDA CONTINUES TO HAVE POWER STEERING ISSUES. TODAY 5/11/13, A FRIEND INFORMED US THAT THERE IS A MAZDA 3 2007 POWER STEERING RECALL. I AM UPSET THAT MAZDA NEVER SENT ME ANY INFORMATION REGARDING THE RECALL. THAT IS UNACCEPTABLE, THAT IS A VERY REAL CONCERN. I CALLED THE MAZDA DEALER NUMBER, AND IT JUST STATES TO WAIT FOR "SECOND" LETTER, WELL, IT WOULD HAVE BEEN NICE TO HAVE THE FIRST LETTER.THIS IS A HUGE SAFETY PROBLEM, AND VERY IRRESPONSIBLE OF MAZDA NOT TO NOTIFY ALL OWNERS. *TR
I HAVE EXPERIENCED SUDDEN LOSS OF POWER STEERING (ABOUT ONCE A WEEK). ALTHOUGH MAZDA HAS ISSUED A RECALL FOR 2007-2009 MAZDA3 WITH THE SAME PROBLEM, THEY REFUSE TO PAY FOR MY REPAIR BECAUSE THE MANUFACTURING DATE IS A FEW DAYS BEFORE THE RECALL. *TR
2007 MAZDA 3, WHENEVER I COME TO A STOP MY VEHICLE VIBRATES REALLY BAD AS IF IT WANT TO STOP. I HAVE TOOK THE MAZDA BACK TO FLOW MAZDA AND THEY SAID IT WAS NOTHING BUT EVERYTIME I STOP IT DOES THE SAME THING. I ALSO TOOK IT TO SEARS AND THEY SAID THEY SEE NOTHING WRONG WITH THE VEHICLE BUT SOMETHING IS CALLING THE VEHICLE TO VI…
Read full complaint
2007 MAZDA 3, WHENEVER I COME TO A STOP MY VEHICLE VIBRATES REALLY BAD AS IF IT WANT TO STOP. I HAVE TOOK THE MAZDA BACK TO FLOW MAZDA AND THEY SAID IT WAS NOTHING BUT EVERYTIME I STOP IT DOES THE SAME THING. I ALSO TOOK IT TO SEARS AND THEY SAID THEY SEE NOTHING WRONG WITH THE VEHICLE BUT SOMETHING IS CALLING THE VEHICLE TO VIBRATE WHENEVER IT ISN'T MOVING. *TR
WHILE INFLATING TIRES FOR A CUSTOMER THEIR VALVE STEM BROKE. A NEW TPMS SENSOR NEEDED TO BE INSTALLED. *TR
Official recalls
221V494000 · Air Bags:frontal
Jul 1, 2021
Mazda North American Operations (Mazda) is recalling certain 2004-2007 Mazda3 vehicles. During air bag deployment, the plastic emblem on the steering wheel air bag module cover may shatter, and project plastic fragments into the vehicle.
Consequence & remedy
Consequence: Plastic fragments can hit occupants during air bag deployment, increasing the risk of injury.
Remedy: Dealers will replace the air bag module cover, free of charge. Owner letters were mailed between August 28, 2021 and October 28, 2021. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 4921G.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.