IllustrationAS I SLOWED DOWN TO TURN A CORNER, THE POWER STEERING LIGHT CAME ON THE DASH, THE CAR LOST POWER. A FEW DAYS LATER THE SAME THING HAPPENED BUT THE CAR STALLED. SO FAR THIS HAS HAPPEN 6 TIMES. THE DEALER TOLD ME MY CAR IS NOT UNDER THE RECALL NOTICE. *TR
2007 Mazda MAZDA3
Owner reports · Recalls · Investigations
More warning signs than most MAZDA3 years
Owner complaints for the 2007 Mazda MAZDA3 are substantially higher than the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
270–25K
3325–50K
3250–75K
3475–100K
39100–150K
18150K+
183 reports with mileage · 39 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 89 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 36 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 22 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
28 crash reports3 fire reports16 injury reports
Electrical System complaints
19 reportsTHE BRAKE LIGHT HOUSING (AMBER LENS) WAS HEATED BY THE BULB TO SUCH A DEGREE THAT THE LENS ITSELF MELTED ONTO THE BULB. WE ARE NOT ENTIRELY SURE WHEN THIS HAPPENED AND MAY HAVE BEEN ONGOING FOR QUITE SOME TIME. UPON INSPECTION BY AN EXPERIENCED AUTOMOTIVE TECHNICIAN, IT WAS CONFIRMED THAT THE BULBS WERE THE CORRECT MODEL AND HAD…
Read full complaint
THE BRAKE LIGHT HOUSING (AMBER LENS) WAS HEATED BY THE BULB TO SUCH A DEGREE THAT THE LENS ITSELF MELTED ONTO THE BULB. WE ARE NOT ENTIRELY SURE WHEN THIS HAPPENED AND MAY HAVE BEEN ONGOING FOR QUITE SOME TIME. UPON INSPECTION BY AN EXPERIENCED AUTOMOTIVE TECHNICIAN, IT WAS CONFIRMED THAT THE BULBS WERE THE CORRECT MODEL AND HAD BEEN INSTALLED CORRECTLY. SOME OF THE PLASTIC HAD MELTED DOWN ONTO THE BULB ITSELF AND COULD POTENTIALLY BECOME A FIRE HAZARD. THIS PROBLEM IMPACTED BOTH DRIVER AND PASSENGER SIDES, WITH THE DRIVER SIDE APPEARING MORE SIGNIFICANTLY MELTED. AFTER A QUICK SEARCH ON MAZDA FORUMS, THIS APPEARS TO BE AN ISSUE EXPERIENCED BY MANY OWNERS OF 2007 MAZDA 3 MODELS, BUT ONLY THOSE IN THE HATCHBACK CONFIGURATION. *TR
THE CHECK ENGINE LIGHT CAME ON. CAUSE ,AFTER RUNNING CODE CHECK,P2004. RUNNER CONTROL VALE STUCK. REPLACE SOLENOID. FRONT STRUTS GONE. *TR
I HAVE CONSTANTLY REPLACED MY DRIVER WINDOW MOTOR. THE DRIVER WINDOW SWITCH/MOTOR STOPS WORKING FOR NO REASON. IN ADDITION THE ENTIRE HEADUNIT STOPS WORKING. IT SHUTS ON AND OFF WHILE IN THE MIDDLE OF DRIVING. SOMETIMES TO POWERS RIGHT BACK ON AND OTHER TIMES IT CAN TAKE DAYS FOR IT TO TURN BACK ON. *TR
POWER WINDOW CONTROL ISSUE ON DRIVER'S SIDE ONLY - THE DRIVER'S POWER WINDOW BUTTON WILL WORK FOR AWHILE AND THEN INTERMITTENTLY STOP WORKING FOR A DAY OR SO. IT WILL RANDOMLY START WORKING AGAIN. NOT SURE IF IT HAPPENS MORE WHEN IT RAINS. I DID SEE THAT GM JUST PUT A RECALL DESCRIBING THE EXACT SAME THING I'M EXPERIENCING AN…
Read full complaint
POWER WINDOW CONTROL ISSUE ON DRIVER'S SIDE ONLY - THE DRIVER'S POWER WINDOW BUTTON WILL WORK FOR AWHILE AND THEN INTERMITTENTLY STOP WORKING FOR A DAY OR SO. IT WILL RANDOMLY START WORKING AGAIN. NOT SURE IF IT HAPPENS MORE WHEN IT RAINS. I DID SEE THAT GM JUST PUT A RECALL DESCRIBING THE EXACT SAME THING I'M EXPERIENCING AND WAS WONDERING IF IT MIGHT BE THE SAME ISSUE...THEY DESCRIBE IT AS MOISTURE ENTERING THE DRIVER'S WINDOW RESULTING IN THE POWER CONTROL NOT WORKING INTERMITTENTLY. IT FIRST STARTED HAPPENING IN MY CAR ABOUT BACK IN MAY, BUT IT MIGHT HAVE BEEN EVEN LONGER. *TR
EVERY 3 MONTHS FRONT HEADLIGHT ARE REPLACED. *TR
IN MARCH 2008, MY VEHICLE HAD WARNING LIGHTS TURN ON FOR BOTH THE SEAT BELT AND ABS SYSTEM. THE DEALER CLEARED THE CODE AND CHECKED THE SYSTEM FOR ERRORS. NO CODES RE-OCCURRED AND THE CAR WAS RETURNED TO ME. SUBSEQUENTLY IN DECEMBER 2008, THE AIRBAG LIGHT CAME ON AGAIN. THE DEALER ADJUSTED SOME WIRING AND CLEARED THE LIGHT/C…
Read full complaint
IN MARCH 2008, MY VEHICLE HAD WARNING LIGHTS TURN ON FOR BOTH THE SEAT BELT AND ABS SYSTEM. THE DEALER CLEARED THE CODE AND CHECKED THE SYSTEM FOR ERRORS. NO CODES RE-OCCURRED AND THE CAR WAS RETURNED TO ME. SUBSEQUENTLY IN DECEMBER 2008, THE AIRBAG LIGHT CAME ON AGAIN. THE DEALER ADJUSTED SOME WIRING AND CLEARED THE LIGHT/CODE. NOW IN SEPTEMBER 2011, THE AIRBAG LIGHT IS ON AGAIN. *TR
BUENAS NOCHES! LAMENTABLEMENTE NO HABLO INGLES, PERO QUISIERA OBTENER INFORMACION ACERCA DE LA FALLA DE FABRICACION EN EL SISTEMA HIDRAULICO (EHPAS) DEL MAZDA 3 DEL 2007. TENGO UNO Y PRESNETO UNA FALLA DONDE EL VOLANTE SE PUSO MUY DURO, Y EN VENEZUELA AUN NO HAN HECHO EL RECALLS. ADEMAS QUISIERA SABER SI HAN HECHO ALGUNA INVEST…
Read full complaint
BUENAS NOCHES! LAMENTABLEMENTE NO HABLO INGLES, PERO QUISIERA OBTENER INFORMACION ACERCA DE LA FALLA DE FABRICACION EN EL SISTEMA HIDRAULICO (EHPAS) DEL MAZDA 3 DEL 2007. TENGO UNO Y PRESNETO UNA FALLA DONDE EL VOLANTE SE PUSO MUY DURO, Y EN VENEZUELA AUN NO HAN HECHO EL RECALLS. ADEMAS QUISIERA SABER SI HAN HECHO ALGUNA INVESTIGACION DEL GENERIC ELECTRONIC MODULE, QUE CONTROLA EL FUNCIONAMIENTO DE: LOS LIMPIA PARA BRISAS, LAS LUCES, EL SISTEMA DE DOBLE TRANSMISION, ESPEJOS RETROVISORES, SISTEMA DE CONTROL DE LAS VENTANAS, Y OTROS. MI VEHICULO TAMBIEN PRESENTO FALLAS DE ESE TIPO Y CREO QUE ES UNA FALLA DE FABRICACION DE ESE MODULO (GEM) SI TIENEN ALGUNA EXPERIENCIA O QUEJAS DE LOS USUARIOS, PODRIA POR FAVOR ENVIARME ESA INFORMACION. *TR
2007 MAZDA 3 INSTRUMENT PANEL GAUGES ARE VERY HARD TO READ IN BRIGHT DAYLIGHT. THE SPEEDOMETER IS MY MAIN PROBLEM.*AK
Official recalls
221V494000 · Air Bags:frontal
Jul 1, 2021
Mazda North American Operations (Mazda) is recalling certain 2004-2007 Mazda3 vehicles. During air bag deployment, the plastic emblem on the steering wheel air bag module cover may shatter, and project plastic fragments into the vehicle.
Consequence & remedy
Consequence: Plastic fragments can hit occupants during air bag deployment, increasing the risk of injury.
Remedy: Dealers will replace the air bag module cover, free of charge. Owner letters were mailed between August 28, 2021 and October 28, 2021. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 4921G.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.