IllustrationMy daughter and I were on the way to O'Reilly when we turned at a short curve going under 20 miles and the steering wheel got loose and the brakes wouldn't stop us. The car just kept swerving all over the road and we ended up in a ditch the day after my husband purchased the car.
2007 Mazda MAZDA3
Owner reports · Recalls · Investigations
More warning signs than most MAZDA3 years
Owner complaints for the 2007 Mazda MAZDA3 are substantially higher than the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
270–25K
3325–50K
3250–75K
3475–100K
39100–150K
18150K+
183 reports with mileage · 39 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 89 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 36 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 22 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
28 crash reports3 fire reports16 injury reports
Air Bags complaints
36 reportsGot a email stating I had a recall on my air bags
The airbag light on Dash comes on and goes off randomly then going on for 6 months. Obviously there's an open circuit in system that others have as well See a lot of others on here with the same problem over 100,000 miles
MY DAUGHTER WAS DRIVING ON CITY STREET WHEN SHE WAS INVOLVED IN AN ACCIDENT BACK IN OCTOBER 2018 WERE SHE FLIPPED INTO A STREAM. SHE ESCAPED WITH BRUISES AND CUTS, I AM VERY THANKFUL THAT NOTHING WORSE HAPPEN TO HER. WHEN THE WRECKER WAS PULLING HER CAR OUT, I NOTICED THAT THE ROOF OF THE CAR WAS CRUSHED IN AS WELL AS THE FRONT…
Read full complaint
MY DAUGHTER WAS DRIVING ON CITY STREET WHEN SHE WAS INVOLVED IN AN ACCIDENT BACK IN OCTOBER 2018 WERE SHE FLIPPED INTO A STREAM. SHE ESCAPED WITH BRUISES AND CUTS, I AM VERY THANKFUL THAT NOTHING WORSE HAPPEN TO HER. WHEN THE WRECKER WAS PULLING HER CAR OUT, I NOTICED THAT THE ROOF OF THE CAR WAS CRUSHED IN AS WELL AS THE FRONT AND BACK OF THE VEHICLE. THE MAZDA 3 THAT WE PURCHASED FOR OUR DAUGHTER WAS TOTALED BUT NO AIRBAGS EVER CAME OUT. THE COP, EMS WORKER, AND I WAS WONDERING WHY NONE OF THE AIRBAGS DEPLOYED. I KEPT CHECKING TO SEE IF THERE WAS A RECALL ON HER CAR BUT THE WEBSITE KEEPS SAYING 0. I REALLY THINK THIS SHOULD BE INVESTIGATED PROMPTLY!
TAKATA RECALL. INQUIRING IF THIS VEHICLE IS AFFECTED BY THE RECALL.
TECH SCANNED ECU AND FOUND THE FOLLOWING CODES: B2232 AIRBAG CIRCUIT OPEN- LOOP #2 DRIVERS SIDE. LIGHT SENSOR IS ON, AIRBAGS WILL NOT DEPLOY IF INVOLVED IN ACCIDENT. MANY ONLINE FORUMS HAVE DISCUSSED ISSUE EVOLVING AFTER 100K. MANY PEOPLE HAVE PAID OUT OF POCKET. I AM AND HAVE BEEN THE ONLY OWNER OF THIS VEHICLE. THE WARNING LI…
Read full complaint
TECH SCANNED ECU AND FOUND THE FOLLOWING CODES: B2232 AIRBAG CIRCUIT OPEN- LOOP #2 DRIVERS SIDE. LIGHT SENSOR IS ON, AIRBAGS WILL NOT DEPLOY IF INVOLVED IN ACCIDENT. MANY ONLINE FORUMS HAVE DISCUSSED ISSUE EVOLVING AFTER 100K. MANY PEOPLE HAVE PAID OUT OF POCKET. I AM AND HAVE BEEN THE ONLY OWNER OF THIS VEHICLE. THE WARNING LIGHT DOES NOT GO AWAY IF TRYING TO JUST RESET IT. IT WILL ILLUMINATE AGAIN WITHIN SECONDS OF VEHICLE BEING TURNED ON.
MY AIR BAG WARNING LIGHT IS CONSTANTLY ON, SOMETIMES IT TURNS OFF BUT GOES BACK ON AND STAYS ON. THIS HAS BEEN GOING ON FOR A YEAR NOW. I RECIEVE EMAIL FOR MAZDA RECALLS. I NOTICE THAT WERE TWO MAZDA RECALLS FOR AIR BAGS. RECALL NUMBER 2304J-A CRACK IN THE AIR BAG CRASH ZONE SENSOR HOUSING AND MADA RECALL NUMBER 2504K-A CRAC…
Read full complaint
MY AIR BAG WARNING LIGHT IS CONSTANTLY ON, SOMETIMES IT TURNS OFF BUT GOES BACK ON AND STAYS ON. THIS HAS BEEN GOING ON FOR A YEAR NOW. I RECIEVE EMAIL FOR MAZDA RECALLS. I NOTICE THAT WERE TWO MAZDA RECALLS FOR AIR BAGS. RECALL NUMBER 2304J-A CRACK IN THE AIR BAG CRASH ZONE SENSOR HOUSING AND MADA RECALL NUMBER 2504K-A CRACK IN THE SOLDER CONNECTION ATTACHING THE ACCELERATION SENSOR IN THE SAS UNIT. I CALLED MAZDA ALL THEY HAD TO SAY THAT MY VIN NUMBER SHOWS NO RECALL. IM AFRAID IF I GET INTO AN ACCIDENT MY AIR BAG WILL NOT WORK. THIS RECALL SHOULD COVER MY MAZDA. PLEASE HELP, THANK YOU.
MAZDA DEALERSHIP SAID I NEED TO REPLACE THE CLOCK SPRING DUE TO THE AIR BAG LIGHT BEING ON.
FUEL PROPULSION SYSTEM CRACKED AT COUPLING UNDER THE REAR PASSENGER SEAT SPEWING MASSIVE AMOUNTS OF FUEL INTO THE CAB SOAKING THE REAR SEAT PAD FIRE RISK PRESENT WITH ELECTRIC PLUG THERE STRUTS ARE UNSTABLE AND NOISY VVT MAKES NOISE WHEN STARTED, GRINDING IN FRONT HUBS. VEHICLE HAS SOME OF THESE PROBLEMS DRIVING AND PARKED. AIRB…
Read full complaint
FUEL PROPULSION SYSTEM CRACKED AT COUPLING UNDER THE REAR PASSENGER SEAT SPEWING MASSIVE AMOUNTS OF FUEL INTO THE CAB SOAKING THE REAR SEAT PAD FIRE RISK PRESENT WITH ELECTRIC PLUG THERE STRUTS ARE UNSTABLE AND NOISY VVT MAKES NOISE WHEN STARTED, GRINDING IN FRONT HUBS. VEHICLE HAS SOME OF THESE PROBLEMS DRIVING AND PARKED. AIRBAGS SYSTEM NON ACTIVE. OTHER ISSUES UNKNOWN BUT POSSIBLE 35.
TL* THE CONTACT OWNS A 2007 MAZDA 3. THE CONTACT STATED THAT THE VEHICLE WAS TAKEN TO A MECHANIC FOR INSPECTION DUE TO TWO DIFFERENT AIR BAG WARNING LIGHTS RANDOMLY ILLUMINATING. THE VEHICLE WAS TO BE FURTHER TESTED AND DIAGNOSED TO DETERMINE THE CAUSE OF THE FAILURE. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MIL…
Read full complaint
TL* THE CONTACT OWNS A 2007 MAZDA 3. THE CONTACT STATED THAT THE VEHICLE WAS TAKEN TO A MECHANIC FOR INSPECTION DUE TO TWO DIFFERENT AIR BAG WARNING LIGHTS RANDOMLY ILLUMINATING. THE VEHICLE WAS TO BE FURTHER TESTED AND DIAGNOSED TO DETERMINE THE CAUSE OF THE FAILURE. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS NOT AVAILABLE.
Official recalls
221V494000 · Air Bags:frontal
Jul 1, 2021
Mazda North American Operations (Mazda) is recalling certain 2004-2007 Mazda3 vehicles. During air bag deployment, the plastic emblem on the steering wheel air bag module cover may shatter, and project plastic fragments into the vehicle.
Consequence & remedy
Consequence: Plastic fragments can hit occupants during air bag deployment, increasing the risk of injury.
Remedy: Dealers will replace the air bag module cover, free of charge. Owner letters were mailed between August 28, 2021 and October 28, 2021. Owners may contact Mazda customer service at 1-800-222-5500 Option 4. Mazda's number for this recall is 4921G.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.