IllustrationI PURCHASED THIS VEHICLE USED IN 2014FROM A FORD LINCOLN, MERCURY DEALERSHIP. I AM NOW ATTEMPTING, THROUGH DISCOVERY, TO DETERMINE IF THIS VEHICLE VIA ITS VIN# HAS ANY RECALLS AGAINST IT!
2012 Lincoln Mkz
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2012 Lincoln Mkz do not stand out strongly from the model-year median of 109.
About this comparison →How this year compares
Owner complaints by model year
Compare all Mkz years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
130–25K
1925–50K
1750–75K
875–100K
14100–150K
3150K+
74 reports with mileage · 72 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 68 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Steering. Review the 20 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 17 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
10 crash reports2 fire reports7 injury reports
Vehicle Speed Control complaints
3 reportsTL* THE CONTACT OWNS A 2012 LINCOLN MKZ. WHILE DRIVING APPROXIMATELY 50 MPH AND ATTEMPTING TO ACCELERATE, THE VEHICLE FAILED TO RESPOND. THE FAILURE RECURRED ON SEVERAL OCCASIONS. THE VEHICLE WAS TAKEN TO THE DEALER, BUT THE FAILURE WAS UNABLE TO BE DETERMINED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF…
Read full complaint
TL* THE CONTACT OWNS A 2012 LINCOLN MKZ. WHILE DRIVING APPROXIMATELY 50 MPH AND ATTEMPTING TO ACCELERATE, THE VEHICLE FAILED TO RESPOND. THE FAILURE RECURRED ON SEVERAL OCCASIONS. THE VEHICLE WAS TAKEN TO THE DEALER, BUT THE FAILURE WAS UNABLE TO BE DETERMINED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 21,000.
I FULLY STOPPED IN A PARKING PLACE WHERE I USE TO GO EVERY MONDAY TO PICK UP KIDS FROM A DANCING SCHOOL. AFTER I FULLY STOPPED AND TRY TO PUT THE CLUTCH ON P THE CAR ACCELERATED BY ITSELF. I WENT TROUGH A BUILDING AND AS I TRIED TO CONTROL THE CAR I WAS TRYING TO PUT IN P AND I WAS NOT ABLE. I KEPT MY FOOT ON THE BRAKE AND T…
Read full complaint
I FULLY STOPPED IN A PARKING PLACE WHERE I USE TO GO EVERY MONDAY TO PICK UP KIDS FROM A DANCING SCHOOL. AFTER I FULLY STOPPED AND TRY TO PUT THE CLUTCH ON P THE CAR ACCELERATED BY ITSELF. I WENT TROUGH A BUILDING AND AS I TRIED TO CONTROL THE CAR I WAS TRYING TO PUT IN P AND I WAS NOT ABLE. I KEPT MY FOOT ON THE BRAKE AND TRIED TO STABILIZE THE CAR..EVENTUALLY THE CAR ENDED IN A DITCH AND I WAS ABLE TO EXIT IMMEDIATELY. THE AIR BEGS OPENED ONLY AFTER I EXIT THE CAR. I WAS IN COMPLETE SHOCK AND I WAS TAKEN TO A LOCAL HOSPITAL BY THE RESCUE SQUAD. I ASKED MY INSURANCE TO KEEP THE COMPLETELY DAMAGED CAR TO BE INSPECTED BY LINCOLN INSPECTORS SINCE THE CAR HAD 2 PROBLEMS 1. ACCELERATED WHEN FULLY STOPPED 2 AIR BEGS DID NOT OPEN DURING THE CRASH WITH THE BUILDING MY INSURANCE CHUBB WROTE TO LINCOLN COMPANY BUT UNTIL TODAY NO ONE RESPONDED OR INSPECTED THE DAMAGED CAR. I WAS LUCKY THE KIDS WERE STILL IN CLASS, I COULD HAVE HEARD MANY OF THEM IF I WOULD HAVE BEEN A FEW MINUTES LATER. I REQUEST AN INVESTIGATION OF THE CAR SINCERELY *TR
Official recalls
521V158000 · Air Bags:frontal:driver Side:inflator Module
Mar 10, 2021
Ford Motor Company (Ford) is recalling certain 2007-2011 Ranger, 2006-2012 Fusion, Lincoln Zephyr, Lincoln MKZ, 2006-2011 Mercury Milan, 2007-2010 Ford Edge, and Lincoln MKX vehicles. The driver's side air bag inflator may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will replace the driver-side airbag inflator or module with an alternate one, free of charge. Owner notification letters were mailed on April 9, 2021 for the passenger side, and November 14, 2022 for the driver side. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S12.
19V001000 · Air Bags:frontal:passenger Side:inflator Module
Jan 7, 2019
Ford Motor Company (Ford) is recalling certain 2014 Ford Mustang vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Ford is recalling certain 2011 Ford Ranger and Mercury Milan vehicles, 2011-2012 Ford Fusion and Lincoln Zephyr/MKZ vehicles and 2011-2014 Ford Mustang vehicles sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Ford is also recalling certain 2010 Ford Edge and Lincoln MKX vehicles, 2010-2011 Ford Ranger and Mercury Milan vehicles, 2010-2012 Ford Fusion and Lincoln Zephyr/MKZ vehicles, and 2010-2014 Ford Mustang vehicles sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules, used as original equipment or replacement equipment (such as after a vehicle crash necessitating replacement of the original air bags), that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 13, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall 19S01.
18V775000 · Air Bags:frontal:passenger Side:inflator Module
Nov 1, 2018
Ford Motor Company (Ford) is recalling certain 2010 Ford Fusion, Mercury Milan and 2010-2012 Lincoln MKZ vehicles that previously received a replacement passenger air bag under recall 16V-384, 17V-024 or 18V-046. In the event of a crash requiring deployment of the passenger air bag, the bracket that secures the air bag inflator to the module housing may deform, allowing the gas that inflates the air bag to leak out.
Consequence & remedy
Consequence: If the air bag does not inflate as intended, there is an increased risk of injury in the event of a crash.
Remedy: Ford will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began November 21, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S34.
17V024000 · Air Bags:frontal:passenger Side:inflator Module
Jan 10, 2017
Ford Motor Company (Ford) is recalling certain 2012 Ford Fusion and Mustang and Lincoln Zephyr and MKZ vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Ford is recalling certain 2009 Ford Ranger, Edge, Fusion and Mustang, Lincoln MKX, MKZ and Zephyr and Mercury Milan vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, Ford is recalling certain 2007-2008 Ford Ranger, Edge and Lincoln MKX, 2006-2008 Ford Fusion, Mercury Milan, Lincoln Zephyr and MKZ, 2005-2008 Ford Mustang and 2005-2006 Ford GT vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Interim letters informing owners of the recall and that parts are not yet available began mailing March 1, 2017. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
15V340000 · Steering:electric Power Assist System
Jun 2, 2015
Ford Motor Company (Ford) is recalling certain model year 2011-2012 Ford Fusion vehicles without a 3.5L engine and Lincoln MKZ hybrid electric vehicles, 2011 Mercury Milan vehicles, 2011-2012 Ford Taurus, Ford Flex, Lincoln MKS, and Lincoln MKT vehicles equipped with a 3.5L GTDI engine and 2013 Ford Taurus, Ford Flex, Lincoln MKS, and Lincoln MKT vehicles equipped with any available engine. The affected vehicles have electric power steering assist systems that may shut down as a result of a steering motor sensor fault.
Consequence & remedy
Consequence: If the vehicle experiences a loss of power steering assist, extra steering effort will be required at lower speeds, increasing the risk of a vehicle crash.
Remedy: Ford will notify owners, and dealers will check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTC). If dealers find any loss of steering assist DTCs, the steering gear will be replaced, free of charge. If, no codes are found during the PSCM inspection, the PSCM software will be updated, free of charge. The recall began on July 21, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S18.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE14030 · Electric Power Steering Failure
Opened Oct 2, 2014 · Closed Sep 10, 2015
Status: closed (inferred from source dates) · Steering:electric Power Assist System
The Office of Defects Investigation (ODI) opened a preliminary evaluation to investigate complaints of the loss of power steering while driving. The subject vehicles are equipped with a rack mounted Electric Power Assisted Steering (EPAS) unit.Some of the complaints alleged that the steering assist failed and resulted in increased steering efforts that contributed to a loss of control and in some cases a crash.The EPAS system was manufactured by TRW Automotive for Ford and was designated as Generation I.These units were first produced and put into vehicle production in July 2008 beginning with the model year (MY) 2010 Ford Fusion and Mercury Milan.The system is comprised of a mechanical steering rack-and-pinion gear with torque sensor, electric assist motor, motor position sensor and a power steering control module (PSCM). The PSCM is self-monitoring and designed to detect faults within the system and can store diagnostic trouble codes (DTCs) if a problem is detected.There are 29 potential DTCs the system can detect.Many of these allow the system to go into reduced-assist steering mode by using the default vehicle speed signal should the live speed signal be lost, if voltage to EPAS system falls below 10.7 or goes above 17 volts, the temperature at the PSCM goes above 105C (221F), or if high friction is detected.Some DTCs will cause the system to go into manual steering mode (no assist). On July 1, 2015, Ford filed a Defect Information Report (DIR) identifying a safety related defect in TRW GEN I EPAS systems installed in some of the subject vehicles (NHTSA Recall 15V-340, Ford No. 15S18).The DIR indicated that intermittent electrical connections caused by quality issues associated with conformal coat contamination and ribbon cable pin misalignment within the steering gear motor may lead to a loss of the motor position sensor signal, resulting in a sudden loss of power assist while driving.The recall covers approximately 393,623 vehicles built from September 2010 through February 2012:2011-12 Fusion built SEP 2010 - FEB 2012; 2011-12 Lincoln MKZ built SEP 2010 - FEB 2012; 2011 Milan built SEP 2010 - DEC 2010; 2011-13 Taurus built SEP 2010 - FEB 2012; 2011-13 Flex with 3.5L GTDI engine built SEP 2010 - FEB 2012; and 2011-13 MKS, MKT with 3.5L GTDI engine built SEP 2010 - FEB 2012.The repair consists of updating the PSCM software to prevent a loss of steering assist while driving. The revised software will provide audible and visual warnings to the driver. If one or more of the following DTCs are stored, C1B00-62, C200B-2F, C200B-61, C200B-62, C200C-2F, C200D-49, U0300-00, U2011-49, U2011-61, U3000-46, U3000-49, U3000-61, U3000-72, U3000-96, P07AE-09, the dealer will replace the EPAS system at no charge to the owner.ODI's analysis of failure data for this PE identified a total of 2,584 complaints to ODI and Ford and 9,967 Ford warranty claims related to the alleged defect.The recalled vehicles account for 1,634 of the complaints and 7,311 of the warranty claims.ODI's analysis identified 40 complaints alleging crashes that may be related to loss of steering assist while driving, 20 of which involved vehicles included in Ford's recall.The information available for the alleged crashes were not sufficient to assess specific causes of the incidents or to verify EPAS malfunctions in each case.Most of the crashes were low-speed impacts with curbs or roadside objects resulting in wheel or minor body damage.None of the injury claims indicated medical attention was required.In addition, statistical modeling of the failure data by NHTSA's National Center for Statistics and Analysis projected 10-year failur