← New search

2006 Lexus Is 250

Owner reports · Recalls · Investigations

More warning signs than most Is 250 years

Owner complaints for the 2006 Lexus Is 250 are substantially higher than the model-year median of 35.

About this comparison →

When problems were reported

Mileage at the reported incident

139 reports with mileage · 50 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Structure. Review the 53 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Air Bags. Review the 46 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 19 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

10 crash reports3 fire reports11 injury reports

Engine And Engine Cooling complaints

11 reports
Clear category filter
125,000 miles · Jan 25, 2012
Engine And Engine Cooling

I ENTERED THE HIGHWAY AS I USUALLY DO ON MY WAY TO WORK AND HAD MADE MY WAY TO THE LEFT LANE. I AM IN RUSH HOUR TRAFFIC WHEN ALL OF A SUDDEN MY CAR STARTED TO LOOSE COMPRESSION, IT STARTED TO SLOW DOWN TO ABOUT 25 MILES (WHILE ON A MAIN HIGHWAY) AND A CHECK ENGINE LIGHT CAME ON AND THE VCS NOTIFICATION STARTED FLASHING. I IMME…

Read full complaint

I ENTERED THE HIGHWAY AS I USUALLY DO ON MY WAY TO WORK AND HAD MADE MY WAY TO THE LEFT LANE. I AM IN RUSH HOUR TRAFFIC WHEN ALL OF A SUDDEN MY CAR STARTED TO LOOSE COMPRESSION, IT STARTED TO SLOW DOWN TO ABOUT 25 MILES (WHILE ON A MAIN HIGHWAY) AND A CHECK ENGINE LIGHT CAME ON AND THE VCS NOTIFICATION STARTED FLASHING. I IMMEDIATELY MADE MY WAY TO THE SHOULDER ON THE RIGHT SIDE OF THE HIGHWAY TO LOOK-UP THE CODE AND ALL IT SAID WAS TO TAKE TO THE LEXUS DEALER IMMEDIATELY, WHICH IS WHAT I DID. AFTER ABOUT FOUR HOURS OF WAITING, THE LEXUS DEALER DETERMINED THAT MY 2006 LEXUS NEEDED: VALVE SPRINGS, VALVE LASH ADJUSTER, UPDATED PISTONS AND RINGS AND POSSIBLY A SHORT BLOCK. YES THE ENGINE WAS BAD. *TR

NHTSA ODI #10445181

81,182 miles · Dec 25, 2011
Engine And Engine CoolingStructure

FOR 3-YEARS WE HAVE COMPLAINED TO THE DEALERSHIP REGARDING THE MUSTY SMELL COMING FROM THE A/C VENTS. WE WERE ADVISED BY THE DEALERSHIP TO CUT OFF THE A/C BEFORE ARRIVING HOME TO ALLOW THE UNIT TO DRAIN. WE ALSO WERE ADVISED TO SPRAY LYSOL INTO THE OUTSIDE COWL VENTS WHICH DID IMPROVE THE ODOR BUT THIS A/C MUSTY SMELL HAS ALWAYS…

Read full complaint

FOR 3-YEARS WE HAVE COMPLAINED TO THE DEALERSHIP REGARDING THE MUSTY SMELL COMING FROM THE A/C VENTS. WE WERE ADVISED BY THE DEALERSHIP TO CUT OFF THE A/C BEFORE ARRIVING HOME TO ALLOW THE UNIT TO DRAIN. WE ALSO WERE ADVISED TO SPRAY LYSOL INTO THE OUTSIDE COWL VENTS WHICH DID IMPROVE THE ODOR BUT THIS A/C MUSTY SMELL HAS ALWAYS BEEN AN ISSUE AND IS ALL OVER THE INTERNET. ON 12/20/2011, WE NOTICED WATER WAS APPARENTLY ENTERING THE PASSENGER COMPARTMENT. THE CARPET WAS WET AND THERE WAS EXCESSIVE MOISTURE AND WATER UNDER CARPET. UPON NOTICING THIS PROBLEM WE SCHEDULED AN APPOINTMENT WITH THE DEALERSHIP. I WAS ADVISED THAT MOST LIKELY, THE A/C DRAIN FLAP WAS STUCK AND CORRECTION FOR THIS DEFECT REQUIRED REMOVAL OF THE DRAIN FLAP TO ALLOW THE DRAIN TO FLOW AND NOT BACK UP AND ENTER THE PASSENGER COMPARTMENT. THE DEALER STATED THIS DEFECT HAS OCCURRED BEFORE INVOLVING THE IS250. COST TO CORRECT THIS DEFECT WAS $240 BECAUSE THE TRANSMISSION HAD TO BE DROPPED TO ACCESS THE DRAIN LINE. REMOVING THE WATER/MOISTURE AND DRYING THE CARPET WAS ESTIMATED AT $2K. AGAIN, THIS OBVIOUS DEFECT IS ALL OVER THE NET AND APPARENTLY WELL KNOWN BY THE DEALERSHIP. ALL LEXUS OWNERS SHOULD BE NOTIFIED BY LEXUS SO ALL CAN AVOID THIS POTENTIAL HEALTH ISSUE INVOLVING MOLD AND THE HIGH COST OF REPAIR. IF THE WATER IS NOT NOTICED AND WATER CONTINUES TO BUILD UP IN THE A/C AND UNDER THE CARPETS SERIOUS MOLD RELATED HEALTH ISSUES COULD OCCUR. I DON'T KNOW HOW LONG OUR CAR LEAKED OR BACKED UP WATER BUT A MUSTY SMELL FOR THE PAST 3-YEARS HAS BEEN NOT ONLY OFFENSIVE BUT DANGEROUS CONSIDERING THE HEALTH HAZARDS ASSOCIATED WITH MOLD HERE IN FLORIDA.I RESPECTFULLY SUBMIT THAT THIS DEFECT SHOULD BE ADDRESSED IMMEDIATELY. *TR

NHTSA ODI #10441181

103,501 miles · Aug 23, 2011
Engine And Engine CoolingStructure

HVAC EVAPORATOR DRAIN BLOCKAGE RESULTING IN REPEATED FLOODED INTERIOR AND CARPET MOLD. *TR

NHTSA ODI #10421155

84,000 miles · Aug 7, 2011
Engine And Engine Cooling

I HAVE A 2006 LEXUS IS250. I NOTICED "ROUGH" STARTS AND IDLE. THIS WAS AT OR AROUND 65K MILES. I ASSUMED IT WAS RELATED TO SUPER COLD WEATHER OR "BAD" GAS (AFTER THE CAR SAT UNUSED FOR 2-3 DAYS+) AT AROUND 84K MILES DURING WARM WEATHER - I EXPERIENCED BOTH A ROUGH START AND STALLING AT A STOP SIGN. I TOOK THE VEHICLE INTO M…

Read full complaint

I HAVE A 2006 LEXUS IS250. I NOTICED "ROUGH" STARTS AND IDLE. THIS WAS AT OR AROUND 65K MILES. I ASSUMED IT WAS RELATED TO SUPER COLD WEATHER OR "BAD" GAS (AFTER THE CAR SAT UNUSED FOR 2-3 DAYS+) AT AROUND 84K MILES DURING WARM WEATHER - I EXPERIENCED BOTH A ROUGH START AND STALLING AT A STOP SIGN. I TOOK THE VEHICLE INTO MY LOCAL DEALERSHIP WHERE IT HAS BEEN METICULOUSLY MAINTAINED. THEY DID AN EXTENDED DIAGNOSTIC (KEPT THE CAR OVER A LONG WEEKEND) AND ADVISED MY CAR WAS NOT "FIRING" 65-85% OF THE TIME AND THAT IT WAS CAUSED BY THE VALVE SPRINGS. THIS IS A $5,000 REPAIR. LEXUS CLAIMED BECAUSE THE ISSUE WAS OUTSIDE THE 70K MIKE WARRANTY THEY WOULD PAY FOR THE "PARTS" OF ROUGHLY $4,000 AS "GOODWILL" BUT I WOULD BE RESPONSIBLE FOR THE LABOR AT $945. I DID A SEARCH FOR RECALLS AND LEARNED THAT THE EXACT ISSUE IS UNDER RECALL FOR OTHER MODELS INCLUSIVE OF THE IS350 V6 - WHICH THE COMPANY REGULARLY REFERS TO AS MY CAR'S "SIBLING" AND HAS SHARED PREVIOUS RECALLS WITH. I'VE CONTACTED LEXUS DIRECTLY AND THEY HAVE ADVISED THE OFFER IS FINAL. THEY HAVE REFUSED MY REQUEST TO SPEAK WITH THE MANUFACTURING REP. I BELIEVE THIS "STALL" ISSUE IS A SIGNIFICANT SAFETY CONCERN (PER THE RECALL NOTED) I'VE ASKED LEXUS WHETHER OR NOT THEY HAVE RESEARCHED THIS ISSUE ON THE V6 250 FOR WHICH I'VE NOT RECEIVED A RESPONSE. I BELIEVE THAT LEXUS WOULD HAVE USED THE EXACT SAME MANUFACTURER FOR THESE VALUE SPRINGS AND OR VERY SIMILAR DESIGN SPECIFICATIONS. IT IS INCOMPREHENSIBLE THAT GIVEN THIS SPECIFIC DIAGNOSIS THEY WOULD NOT RESOLVE THIS IMMEDIATELY. I BELIEVE ABSENT A NHTSA INVESTIGATION LEXUS WILL CONTINUE TO HOLD CUSTOMERS HOSTAGE TO PAY FOR THEIR SAFETY ALTHOUGH EVERY INDICATION IS THAT THIS IS A DESIGN/MANUFACTURING DEFECT FOR THIS MODEL AS WELL. *TT

NHTSA ODI #10417820

78,000 miles · Apr 14, 2011
Engine And Engine Cooling

TL* THE CONTACT OWNS A 2006 LEXUS IS250. THE CONTACT WAS DRIVING APPROXIMATELY 70 MPH WHEN THE VEHICLE STALLED WITHOUT WARNING. THE VEHICLE WAS ABLE TO RESTART AND WAS TAKEN TO A DEALER WHERE THEY ADVISED THE CONTACT THAT THEY WERE UNABLE TO DIAGNOSE THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS APPROXIMATE…

Read full complaint

TL* THE CONTACT OWNS A 2006 LEXUS IS250. THE CONTACT WAS DRIVING APPROXIMATELY 70 MPH WHEN THE VEHICLE STALLED WITHOUT WARNING. THE VEHICLE WAS ABLE TO RESTART AND WAS TAKEN TO A DEALER WHERE THEY ADVISED THE CONTACT THAT THEY WERE UNABLE TO DIAGNOSE THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS APPROXIMATELY 78,000. THE VIN WAS UNAVAILABLE.

NHTSA ODI #10395933

37,000 miles · Feb 3, 2011
Engine And Engine CoolingInjury

A YOUNG LADY PARKED HER 2006 IS 250 LEXUS,EQUIPPED WITH A "SMART KEY" SYSTEM, IN HER ATTACHED GARAGE WHICH WAS ON THE GROUND FLOOR OF HER THREE STORY TOWNHOUSE. SHE EXITED THE VEHICLE WITH THE "KEY FOB" ON HER PERSON, BUT EITHER INADVERTENTLY FORGOT TO SHUT DOWN THE ENGINE OR PUSHED THE START BUTTON IN AN EFFORT TO DO SO BUT WAS…

Read full complaint

A YOUNG LADY PARKED HER 2006 IS 250 LEXUS,EQUIPPED WITH A "SMART KEY" SYSTEM, IN HER ATTACHED GARAGE WHICH WAS ON THE GROUND FLOOR OF HER THREE STORY TOWNHOUSE. SHE EXITED THE VEHICLE WITH THE "KEY FOB" ON HER PERSON, BUT EITHER INADVERTENTLY FORGOT TO SHUT DOWN THE ENGINE OR PUSHED THE START BUTTON IN AN EFFORT TO DO SO BUT WAS UNSUCCESSFUL. THE YOUNG LADY DID NOT REALIZE THE VEHICLE WAS RUNNING AND AFTER ENTERING HER TOWNHOUSE FROM THE GARAGE PLACED THE "KEY FOB" ON A TABLE ON THE SECOND FLOOR. THE YOUNG LADY REMAINED IN HER TOWNHOUSE WITH THE VEHICLE RUNNING IN THE GARAGE UNTIL IT RAN OUT OF GASOLINE AND STOPPED. THE YOUNG LADY WAS SUBSEQUENTLY FOUND DEAD IN HER BATHROOM ON THE THIRD FLOOR. THE DEATH WAS DETERMINED TO HAVE BEEN CAUSED BY CARBON MONOXIDE POISONING AS A RESULT OF THE VEHICLE HAVING BEEN LEFT RUNNING IN THE GARAGE. THE VEHICLE LACKED A "SHUT-DOWN" SWITCH TO SHUT THE ENGINE OFF WHEN UNOCCUPIED AND INERT FOR AN INTERVAL OF TIME AND/OR LACKED AN ADEQUATE AURAL WARNING THAT THE "KEY FOB" WAS BEING REMOVED FROM THE VEHICLE WHILE IT WAS RUNNING OR THE OPERATOR HAD EXITED THE VEHICLE WHILE THE ENGINE WAS RUNNING. *TR

NHTSA ODI #10380153

15,000 miles · Feb 25, 2010
Engine And Engine CoolingVehicle Speed ControlCrash

MY LEXUS IS250 SUDDEN ACCELERATION AND CRASH. *TR

NHTSA ODI #10314391

63,000 miles · Feb 23, 2010
Electronic Stability Control (esc)Engine And Engine Cooling

I OWN A 2006 LEXUS IS250 AND THERE IS A PROBLEM THAT I CANNOT SEE TO HANDLE NOR THE DEALER CAN HANDLE. THE PROBLEM WITH THE CAR IS THAT WHEN I'M GOING OVER 60 TO 65 MPH THE CHECK ENGINE LIGHT BLINKS AND THE VSC LIGHT COMES ON. THE CAR DOES NOT ACCELERATE AND JUST THE RPM WOULD GO UP. I TOOK THE CAR IN TO THE DEALER WITH EXTENDED…

Read full complaint

I OWN A 2006 LEXUS IS250 AND THERE IS A PROBLEM THAT I CANNOT SEE TO HANDLE NOR THE DEALER CAN HANDLE. THE PROBLEM WITH THE CAR IS THAT WHEN I'M GOING OVER 60 TO 65 MPH THE CHECK ENGINE LIGHT BLINKS AND THE VSC LIGHT COMES ON. THE CAR DOES NOT ACCELERATE AND JUST THE RPM WOULD GO UP. I TOOK THE CAR IN TO THE DEALER WITH EXTENDED WARRANTY IN HAND ON 4 NOW 5 DIFFERENT OCCASIONS AND EVERYTIME I'M HEARING DIFFERENT STORIES. HERE IS THE LIST. * MAY 22, 2009: 60,000 MILE SERVICE DONE.* SEPT 6, 2009: TOOK THE CAR IN FOR "CHECK VSC & CHECK ENGINE". NEXT DAY THEY TOLD ME NOTHING WAS WRONG WITH THE CAR.* OCT 10, 2009: TOWED CAR TO DEALERSHIP. "CHECK VSC & CHECK ENGINE" LIGHT CAME ON AGAIN.PULLED OVER ON THE HIGHWAY 3 TIMES TO RESET BUT THE LIGHTS DID NOT GO AWAY. PULLED OVER TWICE EARLIER THAT DAY, TWICE THE DAY BEFORE ALSO.* OCT 14, 2009: (LEXUS TOLD YOU THAT THE ISSUES WERE RESOLVED BY SWAPPING THE ENGINE COILS THE DAY OR TWO BEFORE. NO CHARGES.) I REQUESTED AN EMISSIONS TEST BEFORE I CAME TO PICK IT UP. LEXUS CALLED BACK AND TOLD ME THAT THE ENGINE LIGHT CAME BACK ON AGAIN DURING THE EMISSIONS TEST. STILL LOOKING FOR THE PROBLEM.* OCT 18, 2009: LEXUS CALLED, TOLD ME THAT THE PROBLEM WITH THE ENGINE IS BECAUSE OF THE CARBON BUILDUP. THEY WERE GOING TO COVER THE VALVE SPRINGS BUT I WOULD HAVE TO PAY FOR THE CLEANUP WHICH IS $ 960. NOT COVERED BY EXT. WARRANTY. 2 OTHER DEALERS TOLD ME THAT THE CARBON BUILDUP CLEANUP WAS AN INJUNCTION SERVICE AND IT IS SUPPOSED TO ONLY COST 190 DOLLARS. THE FUNNY THING IS THAT THE DEALER WROTE THE PROBLEM IS CAUSED BY "CARBON BUILDUP CLEANUP?" WITH A QUESTION MARK. TOOK THE CAR AND HAD THE INJUNCTION SERVICE DONE. I TOOK THE CAR TO ANOTHER LEXUS DEALER AND THEY TOLD ME THAT WHILE THE OTHER DEALER WAS DOING THE COIL SWAP THEY CRACKED THE COVER FOR IT AND NOW GAS WAS LEAKING. HAD TO GET IT FIXED AND ALSO DID THE CARBON BUILDUP CLEANUP (INJUNCTION SERVICE). FEB 2010 SAME PROBLEM OCCURRED. *TR

NHTSA ODI #10312962

20,000 miles · Nov 8, 2009
Engine And Engine Cooling

I WAS OPERATING MY 2006 LEXUS IS250 AWD AT VERY LOW SPEED IN A PARKING LOT WHEN THE ENGINE BEGAN TO SURGE. I COULD NOT BRING THE CAR TO A STOP USING THE BRAKE PEDAL AND COULD BARELY KEEP IT FROM CREEPING FORWARD. I SHIFTED INTO NEUTRAL AND THE ENGINE REALLY BEGAN TO ROAR, REVVING VERY HIGH, BUT I WAS THEN ABLE TO STOP THE CAR AN…

Read full complaint

I WAS OPERATING MY 2006 LEXUS IS250 AWD AT VERY LOW SPEED IN A PARKING LOT WHEN THE ENGINE BEGAN TO SURGE. I COULD NOT BRING THE CAR TO A STOP USING THE BRAKE PEDAL AND COULD BARELY KEEP IT FROM CREEPING FORWARD. I SHIFTED INTO NEUTRAL AND THE ENGINE REALLY BEGAN TO ROAR, REVVING VERY HIGH, BUT I WAS THEN ABLE TO STOP THE CAR AND TURN IT OFF USING THE STOP/START BUTTON. WHEN I RESTARTED THE CAR IT OPERATED NORMALLY AND THE PROBLEM DID NOT RE-OCCUR. THE FLOOR MAT HAD NOTHING TO DO WITH THE PROBLEM, AS IT WAS A FACTORY MAT HELD IN PLACE BY THE LITTLE HOOKS, AND WAS NOT THE ALL WEATHER MAT. THE MAT WAS IN PLACE AFTER THE INCIDENT. I REPORTED THE OCCURRENCE TO MY DEALER, WARNOCK LEXUS, IN LIVINGSTON, N.J. THEY CHECKED THE CAR OUT AND FOUND NOTHING WRONG AND NO EVIDENCE OF ANYTHING WRONG IN THE COMPUTER'S MEMORY. THE PROBLEM DID NOT RECUR AND THE CAR WAS RETURNED TO LEXUS AT THE END OF THE LEASE. I NOW HAVE A 2009 IS250 AWD AND AM CONCERNED ABOUT THE REPORTS OF THIS PROBLEM. I DON'T FEEL THE FLOOR MAT HAD ANYTHING TO DO WITH IT. THE DATE BELOW IS APPROXIMATE, BUT LEXUS SHOULD HAVE A RECORD OF THE INCIDENT FROM THE DEALER SERVICE DEPARTMENT. *TR

NHTSA ODI #10291405

42,000 miles · Mar 16, 2009
Engine And Engine Cooling

CAR STARTED TO RUN ROUGH, SLOWED DOWN, CHECK ENGINE LIGHT AND SBS LIGHT CAME ON (ITHOUGHT IT WAS AN OXYGEN SENSOR). BOOK SAYS TO TAKE TO DEALER IMMEDIATELY. I TOOK IT IN, THEY DID A CHECK, TOLD ME IT WAS A 'LOOSE GAS CAP'. A MONTH LATER - SAME THING HAPPENED. I TOOK IT BACK, THEY KEPT THE CAR FOR TWO WEEKS - TOLD ME THE VALVE SP…

Read full complaint

CAR STARTED TO RUN ROUGH, SLOWED DOWN, CHECK ENGINE LIGHT AND SBS LIGHT CAME ON (ITHOUGHT IT WAS AN OXYGEN SENSOR). BOOK SAYS TO TAKE TO DEALER IMMEDIATELY. I TOOK IT IN, THEY DID A CHECK, TOLD ME IT WAS A 'LOOSE GAS CAP'. A MONTH LATER - SAME THING HAPPENED. I TOOK IT BACK, THEY KEPT THE CAR FOR TWO WEEKS - TOLD ME THE VALVE SPRINGS WERE NOT THE CORRECT LENGTH AND HAD TO BE REPLACED. *TR

NHTSA ODI #10261991

Official recalls

6

19V741000 · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

Oct 17, 2019

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front driver inflator, front passenger airbag inflator, the airbag assembly, or the front passenger airbag sub-assembly and inflator. The recall began November 20, 2019. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are J0A, J0B, and J0C. Lexus' numbers for this recall are JLI, JLJ, and JLK.

Additional source detail variants (2)

Air Bags:frontal:passenger Side:inflator Module

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front driver inflator, front passenger airbag inflator, the airbag assembly, or the front passenger airbag sub-assembly and inflator. The recall began November 20, 2019. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are J0A, J0B, and J0C. Lexus' numbers for this recall are JLI, JLJ, and JLK.

Air Bags:frontal:driver Side:inflator Module

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front driver inflator, front passenger airbag inflator, the airbag assembly, or the front passenger airbag sub-assembly and inflator. The recall began November 20, 2019. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are J0A, J0B, and J0C. Lexus' numbers for this recall are JLI, JLJ, and JLK.

17V006000 · Air Bags:frontal:passenger Side:inflator Module

Jan 9, 2017

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2012 Toyota 4Runner, Corolla, Corolla Matrix, Sienna, Yaris, Scion xB, Lexus ES350, GX460, IS-F, IS250, IS350, IS250C, IS350C, and Lexus LFA vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Toyota is recalling certain 2009 Toyota Corolla, Corolla Matrix, Yaris, Yaris HB, Scion xB, Pontiac Vibe, Lexus, ES350, IS250, IS350, and IS-F vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, Toyota is recalling certain 2006-2008 Lexus IS250 and IS350, 2007-2008 Lexus ES350, Toyota Yaris, Yaris HB, and 2008 Lexus IS-F and Scion xB vehicles originally sold, or ever registered in Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Toyota will notify the Toyota, Scion and Lexus owners. General Motors will contact the Pontiac owners. Depending on the model, dealers will replace the passenger frontal air bag inflator or the air bag assembly, free of charge. The recall began on February 1, 2017. Owners may contact Toyota customer service at 1-800-331-4331, or Pontiac customer service at 1-800-762-2737. Toyota's numbers for final remedy for this campaign are G0P (Toyota Zone A), G0R (Toyota Zone B), H0A (Toyota Zone C), GLG (Lexus Zone A), GLH (Lexus Zone B) and HLA (Lexus Zone C).

16V340000 · Air Bags:frontal:passenger Side:inflator Module

May 23, 2016

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2008-2011 Scion xB and Lexus IS F, 2009-2011 Toyota Corolla and Corolla Matrix, 2006-2011 Toyota Yaris, Lexus IS250 and Lexus IS350, 2010-2011 Toyota 4Runner, Lexus IS250C, Lexus IS350C and Lexus GX460, 2011 Sienna, 2007-2011 Lexus ES350, and 2009-2010 Pontiac Vibe vehicles, originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Toyota is recalling certain model year 2008 Scion xB and Lexus IS F, 2007-2008 Toyota Yaris, 2006-2008 Lexus IS250 and Lexus IS350 and 2007-2008 Lexus ES350 vehicles, originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Vehicles of these model years and models that were not originally sold or ever registered in either Zones A or B are not subject to this safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Toyota will notify the Toyota and Lexus owners. General Motors will contact the Pontiac owners. Depending on the model, dealers will replace the passenger frontal air bag inflator or the air bag assembly, free of charge. The recall began on December 6, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for interim notification for this campaign are G1P (Toyota Zone A), G1R (Toyota Zone B), G2G (Lexus Zone A), and G2H (Lexus Zone B). Toyota's numbers for final remedy for this campaign are G0P (Toyota Zone A), G0R (Toyota Zone B), GLG (Lexus Zone A), and GLH (Lexus Zone B).

14V647000 · Fuel System, Gasoline:delivery:hoses, Lines/piping, And Fittings

Oct 15, 2014

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2007-2010 Lexus LS vehicles manufactured May 9, 2006, to July 20, 2010, 2006-2011 Lexus GS vehicles manufactured January 6, 2005, to September 10, 2010, and 2006-2011 Lexus IS vehicles manufactured August 30, 2005, to September 10, 2010. Due to anti-corrosion plating remnants, fuel may leak from where the fuel pressure sensor is attached to the fuel delivery pipe.

Consequence & remedy

Consequence: A fuel leak in the presence of an ignition source increases the risk of a fire.

Remedy: Toyota will notify owners, and dealers will clean and reseal the fuel pressure sensor mounting area, free of charge. The recall began March 3, 2015. Owners may contact Toyota customer service at 1-800-331-4331.

13V030000 · Visibility/wiper

Jan 30, 2013

Toyota is recalling certain model year 2006-2012 Lexus IS250 and IS350 vehicles manufactured August 23, 2005, through October 5, 2011; 2010-2012 Lexus IS250C and IS350C vehicles manufactured April 10, 2009, through October 6, 2011; and 2008-2011 Lexus IS-F vehicles manufactured December 14, 2007, through July 10, 2011. The nuts that fasten the wiper arms may be insufficiently torqued such that if the wiper arms are restricted by an external load, such as a buildup of heavy snow, one or both of the wipers may become inoperative.

Consequence & remedy

Consequence: Inoperative wipers could reduce driver visibility and increase the risk of a vehicle crash.

Remedy: Toyota will notify owners, and Lexus dealers will install new wiper arm nuts, free of charge. An interim letter was mailed to owners on April 4, 2013. Owners may contact Toyota at 1-800-331-4331.

05V565000 · Vehicle Speed Control:accelerator Pedal

Dec 19, 2005

ON CERTAIN PASSENGER VEHICLES, THERE IS A POSSIBILITY THAT THE ACCELERATOR PEDAL MAY TEMPORARILY BECOME STUCK IN THE PARTIALLY DEPRESSED POSITION DUE TO INADEQUATE CLEARANCE BETWEEN THE ACCELERATOR PEDAL LINKAGE AND A PLASTIC PAD EMBEDDED INTO THE VEHICLE'S CARPET.

Consequence & remedy

Consequence: THIS CONDITION MAY INTERFERE WITH THE ACCELERATOR PEDAL RETURNING TO THE IDLE POSITION, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT THE CLEARANCE OF THE ACCELERATION PEDAL AND CARPET, REPLACE THE PEDAL ASSEMBLY WITH A REVISED ASSEMBLY, AND MODIFY THE CARPET FREE OF CHARGE. THE RECALL BEGAN ON DECEMBER 27, 2005. OWNERS MAY CONTACT LEXUS AT 1-800-255-3987.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.