2021 Jeep Grand Cherokee L

A vehicle was purchased at McLarty Daniel Chrysler Bentonville, AR. The sales department had a third party install a non-oem windshield. Dealer attempted repairs, but the records show discrepancies of statements and record. The dealer ignored the instructions to recalibrate the windshield, though the receipt stated “elevated risk of collision” if not calibrated. The owner had on going issues that service should have connected to the windshield and calibration. The windshield of this vehicle has immense safety features that were ignored. The liability to willfully hand over the keys of a known unsafe vehicle is high. The dealership sent a repair request to warranty, only to be denied for “faulty or negligent install” then the service department said “long story short sales will cover the repair” after requesting formal warranty communications did the owner become aware on 7/30/26 and start the process of correction.

This is the second time I got into an accident and the (ADAS) made me crash.. I was far enough to brake safely but the system keeps me going forward..it drags me as if there is ice on the ground..if it was off my car would not have been in any of these accidents..this feature is not safe..I feel like my life is in danger when it is on

When a car in front of me is slowing down while the adaptive crusie control is on and I have the distance set to 3 or 4 lengths, the farthest one available, and the adaptive cruise control is set, the car will start slwoing down like the cars ahead of me and if I switch lanes to go around of the car that is slowing down and there is another car in front of me of the lane I move into that adaptive crusie control acts as if there is no car in front of me in the lane and will begin to accelerate until I engage the brake. So for example I'm traveling in the far right lane of a four lane road, two going north and two going south. I have my adaptive crusie control on and set to 50 MPH and the distance set to 4 car lengths (max) and then the car in front of me starts to slw down. The adaptive crusie control will adjust and start to slow down as well. So I decide to get into the next lane over to my left, where there also happens to be another car 1 or 2 car lengths in front of me, the adaptive crusie control will not detect that car after lane change and will begin to accelerate back up to 50 MPH when it should still be slowing down to avoid a collision. This has happened multiple times.

In May 2025 the vehicle randomly, and without warning, the instruments, gauges, and displays switched to Italian, changed to Metric, and we got the update and FCW Off light stuck on. Numerous other settings had been reset. Took to dealer and had to pay for the fix - they noted a STAR bulletin on my invoice. Then this past weekend (May 2, 2026) it happened again. At least this time it didn't go Italian and Metric on me, but lots of other settings were changed. Did not test the paddle shifters but will do that soon. Current software version says FCA-MY24.U29.42-PROD. I've seen other posts with a newer version - not sure if / why not on my Jeep yet.

Randomly, and without warning, the instruments, gauges, and displays will switch to Italian along with cluster and radio display settings reverting to default settings, auto door locks and paddle shifter becomes inoperative (with no menu to enable), pedestrian emergency brake (peb) lamp or forward collision warning (fcw) lamp turns on with no way to disable, units of measurement including speed, temperature, etc. change to metric and many other random settings change as well. ***This is clearly a dangerous situation because of all the functions and gauges that change, and the fact it is difficult if not impossible to recover from this due to the language of the setting menus, and the complexity of discovering and navigating through all these changes. The dealer charge me $300 diagnostic fee before resetting the software. Time goes by and it happens again. Dealer says there is nothing they can do and to wait for a software update from Stellantis, but none has come and it has been over a year. When this happens, I can change "some" of the settings back but some items cannot be reset like the FCA off lamp and paddle shifters. Back to the dealer I go for another $300 charge. Here is an example Jeep forum discussion, indicating many if not all vehicles are affected: https://www.jeepgarage.org/threads/forward-collision-warning-off-light-is-stuck-on.250301/#replies From personal experience, all of these issues started several years ago with an over the air software. This is a well known and widespread problem, and there is even a DOT Bulletin on the issue: dot.report Bulletins Because this is dangerous (for settings/gauges/units to no longer be useful while driving), and it occurs randomly, I strongly believe this issue should be a manufacturer recall. I am available for any needs."

Randomly, and without warning, the instruments, gauges, and displays will switch into a language I do not speak or understand (Italian). Coinciding with the switch to Italian language, cluster and radio display settings revert back to default settings, auto door locks and paddle shifter becomes inoperative (with no menu to enable), pedestrian emergency brake (peb) lamp or forward collision warning (fcw) lamp turns on with no way to disable, units of measurement including speed, temperature, etc. all change, and many other random settings change as well. ***This is clearly a dangerous situation because of all the functions and gauges that change, and the fact it is difficult if not impossible to recover from this due to the language of the setting menus, and the complexity of discovering and navigating through all these changes. I have taken it to the dealer twice, and they say there is nothing they can do and to wait for a possible software update, but none has come and it has been over a year. When this happens, even if one is able to wade through all the settings menus and change setting back, some items cannot be reset (like the FCA off lamp). According to various Jeep owner forums, some dealers have been able to reset something and temporarily correct the issue, but they charge for this service, and the issue returns randomly again. Here is an example forum discussion, indicating many if not all vehicles are affected: [XXX] Many people on the forum believe this issue did not start until a software update a year or so ago. This is a well known and widespread problem, and there is even a DOT Bulletin on the issue: dot.report Bulletins Because this is dangerous (for settings/gauges/units to no longer be useful while driving), and it occurs randomly, I strongly believe this issue should be a manufacturer recall. I am available for any needs. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

The contact owns a 2021 Jeep Grand Cherokee L. The contact stated while driving 70 MPH on an interstate and depressing the brake pedal to avoid a crash, the automatic emergency braking system suddenly engaged, and the vehicle experienced a drivetrain failure. The contact was able to pull over to the side of the road. There was no warning light illuminated. The vehicle was towed to the local dealer, where it was diagnosed that the drive shaft, the transfer case, and the drivetrain control module had failed and needed to be replaced. The drive shaft was replaced, but additional repairs were needed. The vehicle was not repaired. The manufacturer was notified of the failure, but the case was closed, and the contact was referred to the dealer for assistance. The failure mileage was approximately 93,000.

Randomly, and without warning, the instruments, gauges, and displays will switch into a language I do not speak or understand (Italian). Coinciding with the switch to Italian language, cluster and radio display settings revert back to default settings, auto door locks and paddle shifter becomes inoperative (with no menu to enable), pedestrian emergency brake (peb) lamp or forward collision warning (fcw) lamp turns on with no way to disable, units of measurement including speed, temperature, etc. all change, and many other random settings change as well. ***This is clearly a dangerous situation because of all the functions and gauges that change, and the fact it is difficult if not impossible to recover from this due to the language of the setting menus, and the complexity of discovering and navigating through all these changes. I have taken it to the dealer twice, and they say there is nothing they can do and to wait for a possible software update, but none has come and it has been over a year. When this happens, even if one is able to wade through all the settings menus and change setting back, some items cannot be reset (like the FCA off lamp). According to various Jeep owner forums, some dealers have been able to reset something and temporarily correct the issue, but they charge for this service, and the issue returns randomly again. Here is an example forum discussion, indicating many if not all vehicles are affected: [XXX] Many people on the forum believe this issue did not start until a software update a year or so ago. This is a well known and widespread problem, and there is even a DOT Bulletin on the issue: dot.report Bulletins Because this is dangerous (for settings/gauges/units to no longer be useful while driving), and it occurs randomly, I strongly believe this issue should be a manufacturer recall. I am available for any needs." INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

2021 Jeep Grand Cherokee L. I was idling at a light, which means the engine had auto-shut off. The light turned green and I stepped on the accelerator. Car kicked back on like normal and I got back up to speed ~45 mph. So now I'm about 1/4 mile past the light and I hear the engine kick off and lost all acceleration (everything else was normal). Warning popped up on the dash that "vehicle is not in park". I put on my hazards, braked to a stop, put the vehicle in park (nothing happened), hit the push button to turn the vehicle off, waited 2 seconds, hit the button again to turn it back on. It restarted.

My Jeep over the last year has automatically put itself into park while I’m driving down the highway! I’ve had near miss accidents due to this. No warning lights, no signs something is wrong. It just either slams itself into park and locks up, then won’t turn off. The last times without warning my engine shuts off, my screen pops up saying put into park to start engine and the vehicle puts itself into park automatically. It’s happens fast to! I was swerved by other drivers each time. Jeep will do NOTHING about this! My power steering goes out randomly also. This has happened more than once since the end of 2023! I’m now scared to drive it.