← New search

2018 Jeep Cherokee

Owner reports · Recalls · Investigations

More warning signs than most Cherokee years

Owner complaints for the 2018 Jeep Cherokee are substantially higher than the model-year median of 113.

About this comparison →

When problems were reported

Mileage at the reported incident

359 reports with mileage · 324 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Power Train. Review the 292 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 190 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 155 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

11 crash reports5 fire reports3 injury reports

Unknown Or Other complaints

173 reports
Clear category filter
100 miles · Feb 24, 2019
Unknown Or Other

THE CAR VIBRATES EXCESSIVELY WHEN THE SUNROOF IS OPEN. ONCE YOU ALSO OPEN THE WINDOWS, THE VIBRATION SUBSIDES BUT NEVER GOES COMPLETELY AWAY

NHTSA ODI #11182203

9,688 miles · Feb 18, 2019
Unknown Or Other

WHILE VEHICLE WAS IN MOTION A 'SERVICE SHIFTER' LIGHT ELIMINATED AND ALL OF THE GEAR LIGHTS WERE ON WHILE THE CAR WAS IN DRIVE. ONCE I STOPPED THE CAR, PARKED, AND TURNED THE ENGINE OFF, I WAITED A FEW MINUTES AND RESTARTED THE CAR, THE LIGHTS WERE GONE. THIS IS THE SECOND TIME IN ONE WEEK THIS HAS HAPPENED.

NHTSA ODI #11180822

8,000 miles · Jan 29, 2019
Unknown Or OtherCrashInjury

I BACKED OUT OF MY GARAGE INTO THE DRIVEWAY AND STOPPED THE CAR TO BRING IN THE RECYCLING BIN. I SHIFTED INTO WHAT I THOUGHT WAS PARK, RELEASED THE BREAK, AND EXITED THE CAR. AFTER I HAD EXITED, THE CAR BEGAN TO MOVE FORWARD TOWARD THE OPEN GARAGE. I ATTEMPTED TO JUMP BACK INTO THE CAR IN ORDER TO STOP IT AND SUSTAINED A SERIOUS…

Read full complaint

I BACKED OUT OF MY GARAGE INTO THE DRIVEWAY AND STOPPED THE CAR TO BRING IN THE RECYCLING BIN. I SHIFTED INTO WHAT I THOUGHT WAS PARK, RELEASED THE BREAK, AND EXITED THE CAR. AFTER I HAD EXITED, THE CAR BEGAN TO MOVE FORWARD TOWARD THE OPEN GARAGE. I ATTEMPTED TO JUMP BACK INTO THE CAR IN ORDER TO STOP IT AND SUSTAINED A SERIOUS HAND INJURY AS THE JEEP'S DOOR SLAMMED INTO THE SIDE OF THE GARAGE AND CLOSED BACK UPON ME. SIMILAR RUNAWAY CAR EVENTS HAVE OCCURRED TO ME IN THIS CAR (WITH LESS DRAMATIC CONSEQUENCES) TWICE PRIOR, BUT NEVER IN 25 YEARS BEFORE I PURCHASED THIS 2018 GRAND CHEROKEE. SOME 2018 JEEPS HAVE BEEN RECALLED FOR FAULTY PARK LOCK RODS, SO MY CONCERN IS THAT THE EVENTS I EXPERIENCED HAVE BEEN DUE TO THE INABILITY TO ACHIEVE PARK. EVEN IF I ERRONEOUSLY PUT THE CAR IN DRIVE, IT SHOULD TYPICALLY HAVE STARTED TO MOVE FORWARD AS SOON AS I RELEASED THE BREAK, ALERTING ME THAT THE CAR WAS IN GEAR. INSTEAD, NOTHING HAPPENED FOR 3 SECONDS - THIS PROVIDED A FALSE SENSE OF SECURITY THAT THE CAR WAS IN PARK AND WORSE, GAVE ME ENOUGH OPPORTUNITY TO EXIT. THIS DELAY CAN BE REPRODUCED WHEN TRANSITIONING FROM REVERSE TO DRIVE. LASTLY, WHEN THE DOOR IN THE GRAND CHEROKEE IS OPENED WHILE THE CAR IS IN GEAR, IT SIMPLY BEEPS ONCE - A VERY MINIMAL AND INADEQUATE ALERT SYSTEM.

NHTSA ODI #11172805

13,000 miles · Dec 5, 2018
Electrical SystemUnknown Or Other

FOR THE PAST THREE MONTHS SINCE LABOR DAY OF 2018, MY 2018 JEEP CHEROKEE LATITUDE HAS NOT STARTED ON SEVERAL OCCASIONS. EVENTUALLY IT DOES START BUT IT WILL ALWAYS SAY, "CANNOT READ KEY FOB". I HAVE DISCOVERED THAT IT'S WORSE WHEN I USE THE REMOTE START TO WARM IT UP. WHAT'S REALLY WEIRD IS THAT I HAVE DISCOVERED THAT WHEN I …

Read full complaint

FOR THE PAST THREE MONTHS SINCE LABOR DAY OF 2018, MY 2018 JEEP CHEROKEE LATITUDE HAS NOT STARTED ON SEVERAL OCCASIONS. EVENTUALLY IT DOES START BUT IT WILL ALWAYS SAY, "CANNOT READ KEY FOB". I HAVE DISCOVERED THAT IT'S WORSE WHEN I USE THE REMOTE START TO WARM IT UP. WHAT'S REALLY WEIRD IS THAT I HAVE DISCOVERED THAT WHEN I GET OUT OF MY VEHICLE AND GO TO THE BACK HATCH AND USE THE REMOTE TO LOCK AND UNLOCK THE DOORS, IT STARTS AFTER THAT. GO FIGURE. JUST THIS WEEK, THE DRIVER SIDE DOOR WOULDN'T SHUT TWICE WITHIN THREE DAYS. THE LATCH WAS STUCK. EVENTUALLY, AFTER TRYING JUST ABOUT EVERYTHING I COULD THINK OF LIKE TURNING THE VEHICLE ON AND OFF AND LOCKING AND UNLOCKING THE DOORS FROM THE INSIDE OF THE VEHICLE, I TRIED USING THE REMOTE TO LOCK AND UNLOCK THE DOORS, AND THEN THE DRIVER SIDE DOOR SHUT PROPERLY. I DON'T UNDERSTAND WHY SUCH A NEW VEHICLE PURCHASE BRAND NEW IN APRIL OF THIS YEAR WITH LESS THAN 14, 000 MILES ON IT WOULD HAVE SO MANY PROBLEMS. THE DEALERSHIP IS PICKING IT UP AGAIN TOMORROW FOR THE THIRD TIME TO ATTEMPT TO FIX IT. LAST CHANCE. IF NOT FIXED THIS TIME, I WILL BE GETTING LEGAL REPRESENTATION. NOT SURE IF THESE ARE SAFETY ISSUES BUT I KNOW THAT DRIVING DOWN THE ROAD WITH THE DOOR NOT CLOSED PROPERLY COULD BE A HAZARD. I AM JUST WONDERING IF SOMETHING ELSE MIGHT GO WRONG WITH IT NEXT. I AM REALLY DISAPPOINTED IN THIS VEHICLE TO SAY THE LEAST!

NHTSA ODI #11156450

85 miles · Oct 16, 2018
SteeringSuspensionUnknown Or Other

WHILE DRIVING HIGHWAY SPEEDS THERE IS A VIBRATION BETWEEN 60 AND 80 MILES PER HOUR. I HAVE HAD THE TIRES REPLACED, RIMS REPLACED AND NO CHANGE IN VIBRATION. IT HAS STARTED SINCE I OWNED THE VEHICLE WITH 7 MILES ON THE ODOMETER TILL TODAY WITH 9000 MILES ON IT. THE DEALER CLAIMS THAT THIS IS NORMAL THROUGHOUT THE LINE OF CHEROKEE…

Read full complaint

WHILE DRIVING HIGHWAY SPEEDS THERE IS A VIBRATION BETWEEN 60 AND 80 MILES PER HOUR. I HAVE HAD THE TIRES REPLACED, RIMS REPLACED AND NO CHANGE IN VIBRATION. IT HAS STARTED SINCE I OWNED THE VEHICLE WITH 7 MILES ON THE ODOMETER TILL TODAY WITH 9000 MILES ON IT. THE DEALER CLAIMS THAT THIS IS NORMAL THROUGHOUT THE LINE OF CHEROKEES AND IS JUST "ROAD VIBRATION" BUT TALKING WITH OTHER OWNERS THIS IS NOT THE CASE AND THEY DO NOT EXPERIENCE THE SAME THING. IT DOES TEND TO FADE AWAY DURING LONG LEFT TURNS ON THE FREEWAY BUT APPEARS AS SOON AS THE VEHICLE STRAIGHTENS. NUMEROUS ATTEMPTS TO GET THE DEALERSHIP TO FIX THIS HAS RESULTED IN NO HEADWAY AS THE DEALER CLAIMS THAT THIS IS NORMAL.

NHTSA ODI #11140689

14,186 miles · Sep 12, 2018
Power TrainUnknown Or Other

WHILE DRIVING MY DASH WILL SUDDENLY STATE "SERVICE SHIFTER" AND ALL MY GEAR SHIFTER LIGHTS WILL BE LIT UP. THE ONLY WAY I GET THEM OFF IS I HAVE TO PULL OVER, STOP, TURN VEHICLE OFF, AND RESTART IT. THIS HAS HAPPEN IN TOWN AND ON THE HIGHWAY. THIS HAS HAPPENED NOW SEVERAL TIMES OVER APPROXIMATELY 4 MONTHS NOW. THE FIRST TIME BEI…

Read full complaint

WHILE DRIVING MY DASH WILL SUDDENLY STATE "SERVICE SHIFTER" AND ALL MY GEAR SHIFTER LIGHTS WILL BE LIT UP. THE ONLY WAY I GET THEM OFF IS I HAVE TO PULL OVER, STOP, TURN VEHICLE OFF, AND RESTART IT. THIS HAS HAPPEN IN TOWN AND ON THE HIGHWAY. THIS HAS HAPPENED NOW SEVERAL TIMES OVER APPROXIMATELY 4 MONTHS NOW. THE FIRST TIME BEING WHEN I GOT MY FIRST OIL CHANGE.

NHTSA ODI #11129089

14,000 miles · Aug 29, 2018
Unknown Or Other

PANORAMIC SUNROOF EXPLODED OUTWARD - AT 5:15 AM, I WAS JUST STARTING TO GET ON THE ON RAMP TO THE FREEWAY. I WAS NOT UP TO FREEWAY SPEED YET. WEATHER CONDITIONS WERE GOOD AND APPROX. 61 DEGREES. AS I WAS DRIVING ON THE ONRAMP I HEARD A LOUD EXPLOSION THAT FREAKED ME OUT SO BAD I WAS THANKFUL I DID NOT CRASH. I PULLED TO …

Read full complaint

PANORAMIC SUNROOF EXPLODED OUTWARD - AT 5:15 AM, I WAS JUST STARTING TO GET ON THE ON RAMP TO THE FREEWAY. I WAS NOT UP TO FREEWAY SPEED YET. WEATHER CONDITIONS WERE GOOD AND APPROX. 61 DEGREES. AS I WAS DRIVING ON THE ONRAMP I HEARD A LOUD EXPLOSION THAT FREAKED ME OUT SO BAD I WAS THANKFUL I DID NOT CRASH. I PULLED TO THE SIDE OF THE ROAD ALL TIRES WERE FINE. ALL SURROUNDING WINDOWS WERE FINE. I HAD THE SUNROOF BARRIER CLOSED SO I DIDN'T EVEN THINK ABOUT THE SUNROOF UNTIL I HEARD CHARDS OF GLASS BEADS ON THE BARRIER. I PULLED TO THE SIDE OF THE FREEWAY IN THE DARK AND GRADUALLY OPENED UP THE BARRIER TO THE SUN ROOF A LITTLE. I COULD SEE THAT ALMOST THE ENTIRE PANE OF THE BACK PART OF THE PANORAMIC SUNROOF HAD SHATTERED MAKING A HUGE GAPING HOLE. I TURNED THE CAR AROUND AND WENT HOME. IF IT WAS A ROCK OR SOMETHING WAS DROPPED ON IT THE ROCK STILL WOULD HAVE BEEN THERE ON THE BARRIER. THE SUNROOF LITERALLY BOWS UPWARD AND IT CRACKED AT THE SEAMS SO YOU CAN SEE IT HAS DEFINITELY BLOWN OUT. THIS IS A MANUFACTURER DEFECT THAT COULD HAVE CAUSED AN ACCIDENT OR WORSE IF THE BARRIER HAD BEEN OPEN AND THE GLASS HAD SHATTERED ON ME. IT IS OBVIOUSLY MADE OF SAFETY GLASS. THE EXPLOSION WAS VERY LOUD AND EAR PIERCING.

NHTSA ODI #11123336

16,000 miles · Aug 16, 2018
Unknown Or OtherFire

A FEW MINUTES AFTER PARKING MY CAR, NEIGHBORS REPORTED AN "EXPLOSION" AND LOOKED OUTSIDE TO SEE THE FRONT OF THE CAR ENGULFED IN FLAMES *BF UPDATED 11/26/18*JB

NHTSA ODI #11120518

Mileage unknown · Aug 2, 2018
Unknown Or Other

THE SERVICE SHIFTER LIGHT JUST CAME ON

NHTSA ODI #11115455

8,400 miles · May 3, 2018
Unknown Or Other

MY JEEP DOES NOT STAY LOCKED. I CAN LOCK THE CAR, BUT IF SOMEONE TRIES TO OPEN IT, THEY ARE ABLE TO WITHOUT A PROBLEM, EVEN WHEN THE FOB IS NOWHERE NEAR THE CAR. ALL THAT HAPPENS IS THE THEFT ALARM TRIGGERS. MY CAR WAS OPENED BY SOMEONE IN A PARKING GARAGE AT WORK EVEN THOUGH MYSELF AND THE FOB WERE NOT NEAR THE VEHICLE. THE…

Read full complaint

MY JEEP DOES NOT STAY LOCKED. I CAN LOCK THE CAR, BUT IF SOMEONE TRIES TO OPEN IT, THEY ARE ABLE TO WITHOUT A PROBLEM, EVEN WHEN THE FOB IS NOWHERE NEAR THE CAR. ALL THAT HAPPENS IS THE THEFT ALARM TRIGGERS. MY CAR WAS OPENED BY SOMEONE IN A PARKING GARAGE AT WORK EVEN THOUGH MYSELF AND THE FOB WERE NOT NEAR THE VEHICLE. THE ALARM WENT OFF BUT THE PERSON WAS ABLE TO OPEN MY DOOR WITH NO PROBLEM,

NHTSA ODI #11091525

Official recalls

7

25V011000 · Power Train

Apr 29, 2025

Chrysler (FCA US, LLC) is recalling certain 2017-2019 Jeep Cherokee vehicles. The power transfer unit (PTU) may become damaged and disengage the transmission and differential, resulting in a loss of drive power and/or loss of park function.

Consequence & remedy

Consequence: A loss of drive power can increase the risk of a crash. A loss of park function can cause an unintended vehicle rollaway, which can increase the risk of a crash or injury.

Remedy: Dealers will update the drivetrain control module and PTU software and replace the PTU, as necessary free of charge. Owner notification letters were mailed beginning February 19, 2026. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is 01C.

18V524000 · Electrical System:wiring:front Underhood

Aug 9, 2018

Chrysler (FCA US LLC) is recalling certain 2018 Jeep Renegade, Compass and Grand Cherokee, RAM 1500 and Promaster, Fiat 500x, Dodge Journey, Challenger, Charger and Durango and Chrysler 300x vehicles, 2017-2018 Jeep Wrangler, Dodge Grand Caravan and Chrysler Town and Country vehicles and 2018-2019 Jeep Cherokee and 2018 Chrysler Pacifica and Pacifica Hybrid vehicles. The powertrain control module may be equipped with a voltage regulator chip in the circuit board that may fail, causing a stall or a no start condition.

Consequence & remedy

Consequence: A vehicle stall can increase the risk of a crash.

Remedy: Chrysler will notify owners, and dealers will replace the powertrain control module, free of charge. The recall began October 2, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U87.

18V494000 · Power Train:axle Assembly:axle Shaft

Jul 26, 2018

Chrysler (FCA US LLC) is recalling certain 2018 Jeep Cherokee all-wheel-drive vehicles. The bearing cage for the right front halfshaft assembly may not have been properly heat treated, possibly resulting in the bearing cage breaking and a potential halfshaft assembly failure.

Consequence & remedy

Consequence: If the halfshaft bearing cage breaks, the halfshaft may not be able to transmit engine power, causing a loss of drive or it can allow the vehicle to move while in the "Park" position. Either condition may increase the risk of a crash.

Remedy: Chrysler will notify owners, and dealers will replace the front right halfshaft assemblies, free of charge. The recall began September 20, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U78.

18V332000 · Electrical System:software; Electrical System:wiring; Vehicle Speed Control:cruise Control

May 17, 2018

Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.

Consequence & remedy

Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.

Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.

Additional source detail variants (3)

Electrical System:software

Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.

Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.

Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.

Vehicle Speed Control:cruise Control

Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.

Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.

Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.

Electrical System:wiring

Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.

Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.

Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.

18V282000 · Fuel System, Gasoline:delivery:hoses, Lines/piping, And Fittings

May 1, 2018

Chrysler (FCA US LLC) is recalling certain 2018 Jeep Cherokee vehicles equipped with a 2.4L engine. These vehicles may have been manufactured with a fuel tube that may leak fuel into the engine compartment.

Consequence & remedy

Consequence: A fuel leak in the presence of the ignition source can increase the risk of a fire.

Remedy: Chrysler will notify owners, and dealers will inspect the fuel tube, replacing it as necessary, free of charge. The recall began May 24, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U39.

17V670000 · Engine And Engine Cooling:engine

Oct 24, 2017

Chrysler (FCA US LLC) is recalling certain 2018 Jeep Cherokee and Compass vehicles equipped with 2.4L engines. The engines may have a cracked oil pump housing that can result in oil pump failure.

Consequence & remedy

Consequence: If the oil pump fails, the engine will stall, increasing the risk of a crash.

Remedy: Chrysler will notify owners, and dealers will inspect the oil pump, replacing it as necessary, free of charge. The recall began December 5, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T65.

17V543000 · Equipment:other:labels; Wheels:rim

Aug 31, 2017

Chrysler (FCA US LLC) is recalling certain 2017-2018 Jeep Cherokee vehicles. The tire and rim size information required to be on the Certification label was omitted during manufacturing, which may result in an incorrect tire and rim combination being installed on the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."

Consequence & remedy

Consequence: The missing tire and rim designation information may lead to an incorrect combination being installed on the vehicle, increasing the risk of a crash.

Remedy: Chrysler will notify owners and will provide a corrected certification label, free of charge. The recall began October 13, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T53.

Additional source detail variants (2)

Equipment:other:labels

Chrysler (FCA US LLC) is recalling certain 2017-2018 Jeep Cherokee vehicles. The tire and rim size information required to be on the Certification label was omitted during manufacturing, which may result in an incorrect tire and rim combination being installed on the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."

Consequence: The missing tire and rim designation information may lead to an incorrect combination being installed on the vehicle, increasing the risk of a crash.

Remedy: Chrysler will notify owners and will provide a corrected certification label, free of charge. The recall began October 13, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T53.

Wheels:rim

Chrysler (FCA US LLC) is recalling certain 2017-2018 Jeep Cherokee vehicles. The tire and rim size information required to be on the Certification label was omitted during manufacturing, which may result in an incorrect tire and rim combination being installed on the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."

Consequence: The missing tire and rim designation information may lead to an incorrect combination being installed on the vehicle, increasing the risk of a crash.

Remedy: Chrysler will notify owners and will provide a corrected certification label, free of charge. The recall began October 13, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T53.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.