Illustration4wd service light on. Four wheel drive will not work. Makes noises once and awhile. Vehicle parking brake came on and would not work. Was spinning on ice snow and parking brake activated.
2017 Jeep Cherokee
Owner reports · Recalls · Investigations
More warning signs than most Cherokee years
Owner complaints for the 2017 Jeep Cherokee are substantially higher than the model-year median of 113.
About this comparison →How this year compares
Owner complaints by model year
Compare all Cherokee years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
2010–25K
31925–50K
17950–75K
7075–100K
52100–150K
13150K+
834 reports with mileage · 499 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 646 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 342 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 258 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
24 crash reports6 fire reports17 injury reports
Power Train complaints
646 reportsThe contact owns a 2017 Jeep Cherokee. The contact stated while driving at an undisclosed speed through an intersection, the vehicle lost automotive power. No warning light was illuminated. The contact stated that after restarting the vehicle, the vehicle failed to remain in park(P) and the parking brake was activated to keep th…
Read full complaint
The contact owns a 2017 Jeep Cherokee. The contact stated while driving at an undisclosed speed through an intersection, the vehicle lost automotive power. No warning light was illuminated. The contact stated that after restarting the vehicle, the vehicle failed to remain in park(P) and the parking brake was activated to keep the vehicle from moving. The contact pulled over to the shoulder of the roadway and the vehicle was towed to a local dealer and was repaired for a power transfer unit (PTU) failure. The vehicle was repaired; however, the failure had reoccurred. The vehicle was taken back to the same local dealer and was left for further investigation. The contact received notification of NHTSA Campaign Number: 25V011000 (Power Train) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 70,000. VIN tool confirms parts not available.
Recently there was a recall for 63,082 Jeep Cherokees from the years 2017-2019. I have yet to see my VIN in this list and I'm just not sure why. I have been dealing with a SVC 4WD light on for awhile now and am hearing the noted vibration noises of the safety recall. Why isn't my vehicle included, especially when it's literal…
Read full complaint
Recently there was a recall for 63,082 Jeep Cherokees from the years 2017-2019. I have yet to see my VIN in this list and I'm just not sure why. I have been dealing with a SVC 4WD light on for awhile now and am hearing the noted vibration noises of the safety recall. Why isn't my vehicle included, especially when it's literally having the same problem that other people are being covered on, with my same Jeep year and model. If someone could give me more information on if they will be adding more vehicles to the list...especially ones experiencing this same problem. Thank you for your time. Best, [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The contact owns a 2017 Jeep Cherokee. The contact stated while driving at an undisclosed speed, the vehicle stalled the contact could not confirm which warning light was illuminated. The vehicle was able to restart. The contact received notification of NHTSA Campaign Number: 25V011000 (Power Train); however, the part to do the …
Read full complaint
The contact owns a 2017 Jeep Cherokee. The contact stated while driving at an undisclosed speed, the vehicle stalled the contact could not confirm which warning light was illuminated. The vehicle was able to restart. The contact received notification of NHTSA Campaign Number: 25V011000 (Power Train); however, the part to do the recall repair was unavailable. The dealer was contacted. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was approximately 110,922. VIN tool confirms parts not available.
The contact owns a 2017 Jeep Cherokee. The contact stated that while attempting to drive from a complete stop and depressing the accelerator pedal, the vehicle failed to respond immediately, but responded after several attempts. Additionally, the contact stated that while driving at various speeds and depressing the accelerator …
Read full complaint
The contact owns a 2017 Jeep Cherokee. The contact stated that while attempting to drive from a complete stop and depressing the accelerator pedal, the vehicle failed to respond immediately, but responded after several attempts. Additionally, the contact stated that while driving at various speeds and depressing the accelerator pedal, the vehicle jerked and shuddered, and there was an abnormal grinding sound coming from underneath the vehicle. The vehicle was taken to JMB Automotive, where the diagnostic trouble code C14A7-97 was retrieved. The mechanic informed the contact that the VIN was included in NHTSA Campaign Number: 25V011000 (Power Train) and determined that the failure was related to the recall. The vehicle was taken to the dealer, where the same assessment was made; however, the dealer informed the contact that the part to repair the vehicle was not yet available. The vehicle was not repaired. The contact was referred to the manufacturer. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was contacted and informed the contact that the dealer would be contacted and would be advised to add the vehicle to the recall waiting list. The failure mileage was approximately 90,000. VIN tool confirms parts not available.
There is still no remedy available for a recall with my PTU that was issued at the beginning of 2025. I have to drive my car daily for work and I am afraid for my life while doing so. I don’t have the financial means to purchase a new car, so I’m at the mercy of a company to decide on if the cost to fix this is worth the lives o…
Read full complaint
There is still no remedy available for a recall with my PTU that was issued at the beginning of 2025. I have to drive my car daily for work and I am afraid for my life while doing so. I don’t have the financial means to purchase a new car, so I’m at the mercy of a company to decide on if the cost to fix this is worth the lives of their customers.
The contact owns a 2017 Jeep Cherokee. The contact stated that while the vehicle was parked in his driveway, powered on, parked, and unattended, it began to roll back and crashed into his other vehicle, a 2017 GMC Sierra. The service shift message was displayed. There were no reported injuries, air bag deployment, or fire. A pol…
Read full complaint
The contact owns a 2017 Jeep Cherokee. The contact stated that while the vehicle was parked in his driveway, powered on, parked, and unattended, it began to roll back and crashed into his other vehicle, a 2017 GMC Sierra. The service shift message was displayed. There were no reported injuries, air bag deployment, or fire. A police report was not filed. The contact received notification of NHTSA Campaign Number: 25V011000 (Power Train); however, the part to do the recall repair was not yet available. The local dealer was contacted. The vehicle was taken to the local dealer, who inspected it and determined there was no evidence of a manufacturer defect. The vehicle was not diagnosed or repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The manufacturer opened a case on the contact's behalf. VIN tool confirms parts not available. The failure mileage was approximately 70,000.
The contact owns a 2017 Jeep Cherokee. The contact stated that while driving at an undisclosed speed, the vehicle made an abnormally loud sound. The vehicle was taken to two independent mechanics, who determined that there was grease being splashed from the drive axle. The contact was informed that the drive axle needed to be re…
Read full complaint
The contact owns a 2017 Jeep Cherokee. The contact stated that while driving at an undisclosed speed, the vehicle made an abnormally loud sound. The vehicle was taken to two independent mechanics, who determined that there was grease being splashed from the drive axle. The contact was informed that the drive axle needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 91,000.
My parking brake goes on out of the blue and my warning lights next to the shifter are on indicating there is a problem. My mechanic cannot fix it and the dealership said there is a recall but does not have a remedy, but says it is a SAFETY ISSUE.(!) I am afraid I will get into an accident. Please advise.
The contact owns a 2017 Jeep Cherokee. The contact stated while driving at an undisclosed speed, the 4WD warning light illuminated. The contact stated that the failure had occurred several times in one day. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The dealer was made aware of the failur…
Read full complaint
The contact owns a 2017 Jeep Cherokee. The contact stated while driving at an undisclosed speed, the 4WD warning light illuminated. The contact stated that the failure had occurred several times in one day. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The dealer was made aware of the failure; however, the contact was informed that parts to repair the vehicle were not available. The contact had received notification of NHTSA Campaign Number: 25V011000 (Power Train); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was 40,000. VIN tool confirms parts not available.
Official recalls
625V011000 · Power Train
Apr 29, 2025
Chrysler (FCA US, LLC) is recalling certain 2017-2019 Jeep Cherokee vehicles. The power transfer unit (PTU) may become damaged and disengage the transmission and differential, resulting in a loss of drive power and/or loss of park function.
Consequence & remedy
Consequence: A loss of drive power can increase the risk of a crash. A loss of park function can cause an unintended vehicle rollaway, which can increase the risk of a crash or injury.
Remedy: Dealers will update the drivetrain control module and PTU software and replace the PTU, as necessary free of charge. Owner notification letters were mailed beginning February 19, 2026. Owners may contact FCA customer service at 1-800-853-1403. FCA's number for this recall is 01C.
23V302000 · Power Train:automatic Transmission
Apr 27, 2023
Chrysler (FCA US, LLC) is recalling certain 2016-2017 Jeep Cherokee vehicles. The power transfer unit (PTU) may become damaged and disengage the transmission and differential, resulting in a loss of drive power or loss of park function.
Consequence & remedy
Consequence: A loss of drive power can increase the risk of a crash. A loss of park function can cause an unintended vehicle rollaway which can increase the risk of a crash or injury.
Remedy: FCA US LLC will notify owners, and dealers will perform a software update, free of charge. Owner notification letters were mailed May 11, 2023. Owners may contact FCA USA LLC customer service at 1-800-853-1403. FCA's number for this recall is 45A. This recall expands previous recall number 20V-343.
20V343000 · Power Train:automatic Transmission; Power Train:driveline:differential Unit
Jun 11, 2020
Chrysler (FCA US LLC) is recalling certain 2014-2017 Jeep Cherokee vehicles equipped with a two-speed Power Transfer Unit (PTU). Relative movement in the Power Transfer Unit (PTU) between the differential input splines and the transmission output shaft may cause some input spline teeth to wear off, which may eventually cause a loss of engagement between the transmission and the differential inside the PTU. If this occurs, power cannot be transferred between the front wheels and the transmission which results in a loss of drive while the vehicle is in motion and a loss of the Park function while stationary.
Consequence & remedy
Consequence: A loss of drive can cause a vehicle crash without prior warning. A loss of the Park function can cause unintended vehicle rollaway which can increase the risk of a crash or injury.
Remedy: FCA US LLC will notify owners, and dealers will perform a software update that will maintain vehicle propulsion by engaging rear wheel drive and prevent rolling in Park by activating the electronic parking brake if a failed input spline occurs. This recall began July 14, 2020. Owners may contact FCA USA LLC customer service at 1-800-853-1403. FCA's number for this recall is W47.
Additional source detail variants (2)
Power Train:driveline:differential Unit
Chrysler (FCA US LLC) is recalling certain 2014-2017 Jeep Cherokee vehicles equipped with a two-speed Power Transfer Unit (PTU). Relative movement in the Power Transfer Unit (PTU) between the differential input splines and the transmission output shaft may cause some input spline teeth to wear off, which may eventually cause a loss of engagement between the transmission and the differential inside the PTU. If this occurs, power cannot be transferred between the front wheels and the transmission which results in a loss of drive while the vehicle is in motion and a loss of the Park function while stationary.
Consequence: A loss of drive can cause a vehicle crash without prior warning. A loss of the Park function can cause unintended vehicle rollaway which can increase the risk of a crash or injury.
Remedy: FCA US LLC will notify owners, and dealers will perform a software update that will maintain vehicle propulsion by engaging rear wheel drive and prevent rolling in Park by activating the electronic parking brake if a failed input spline occurs. This recall began July 14, 2020. Owners may contact FCA USA LLC customer service at 1-800-853-1403. FCA's number for this recall is W47.
Power Train:automatic Transmission
Chrysler (FCA US LLC) is recalling certain 2014-2017 Jeep Cherokee vehicles equipped with a two-speed Power Transfer Unit (PTU). Relative movement in the Power Transfer Unit (PTU) between the differential input splines and the transmission output shaft may cause some input spline teeth to wear off, which may eventually cause a loss of engagement between the transmission and the differential inside the PTU. If this occurs, power cannot be transferred between the front wheels and the transmission which results in a loss of drive while the vehicle is in motion and a loss of the Park function while stationary.
Consequence: A loss of drive can cause a vehicle crash without prior warning. A loss of the Park function can cause unintended vehicle rollaway which can increase the risk of a crash or injury.
Remedy: FCA US LLC will notify owners, and dealers will perform a software update that will maintain vehicle propulsion by engaging rear wheel drive and prevent rolling in Park by activating the electronic parking brake if a failed input spline occurs. This recall began July 14, 2020. Owners may contact FCA USA LLC customer service at 1-800-853-1403. FCA's number for this recall is W47.
18V332000 · Electrical System:software; Electrical System:wiring; Vehicle Speed Control:cruise Control
May 17, 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence & remedy
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Additional source detail variants (3)
Electrical System:software
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Vehicle Speed Control:cruise Control
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Electrical System:wiring
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
17V543000 · Equipment:other:labels; Wheels:rim
Aug 31, 2017
Chrysler (FCA US LLC) is recalling certain 2017-2018 Jeep Cherokee vehicles. The tire and rim size information required to be on the Certification label was omitted during manufacturing, which may result in an incorrect tire and rim combination being installed on the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: The missing tire and rim designation information may lead to an incorrect combination being installed on the vehicle, increasing the risk of a crash.
Remedy: Chrysler will notify owners and will provide a corrected certification label, free of charge. The recall began October 13, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T53.
Additional source detail variants (2)
Equipment:other:labels
Chrysler (FCA US LLC) is recalling certain 2017-2018 Jeep Cherokee vehicles. The tire and rim size information required to be on the Certification label was omitted during manufacturing, which may result in an incorrect tire and rim combination being installed on the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."
Consequence: The missing tire and rim designation information may lead to an incorrect combination being installed on the vehicle, increasing the risk of a crash.
Remedy: Chrysler will notify owners and will provide a corrected certification label, free of charge. The recall began October 13, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T53.
Wheels:rim
Chrysler (FCA US LLC) is recalling certain 2017-2018 Jeep Cherokee vehicles. The tire and rim size information required to be on the Certification label was omitted during manufacturing, which may result in an incorrect tire and rim combination being installed on the vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."
Consequence: The missing tire and rim designation information may lead to an incorrect combination being installed on the vehicle, increasing the risk of a crash.
Remedy: Chrysler will notify owners and will provide a corrected certification label, free of charge. The recall began October 13, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T53.
16V799000 · Air Bags:knee Bolster
Nov 2, 2016
Chrysler (FCA US LLC) is recalling certain model year 2017 Jeep Cherokee vehicles manufactured October 13, 2016, to October 17, 2016. Improper welds on the driver's knee air bag inflator may prevent the air bag from properly inflating.
Consequence & remedy
Consequence: If the driver's knee air bag does not properly inflate, there is an increased risk of injury in the event of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the driver's knee air bag module, free of charge. The recall began November 9, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S84.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.