IllustrationWAS DRIVING THE CAR AND STEERING WHEEL LOCKED ON A HIGHWAY ON MY WAY TO WORK. WAS ABLE TO PULL IT OVER CUT THE CAR OFF. STARTED IT BACK UP AND WAS FIND. THEN ON THE WAY BACK HOME HAPPENED AGAIN WHEN TRIED TO EXIT OFF THE HIGHWAY AND ENDED UP IN A DITCH.
2012 Hyundai Genesis
Owner reports · Recalls · Investigations
More warning signs than most Genesis years
Owner complaints for the 2012 Hyundai Genesis are substantially higher than the model-year median of 109.
About this comparison →How this year compares
Owner complaints by model year
Compare all Genesis years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
340–25K
5925–50K
5350–75K
4375–100K
13100–150K
8150K+
210 reports with mileage · 49 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine. Review the 68 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 49 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 39 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
8 crash reports1 fire reports5 injury reports
What owners actually said
259 reportsTRANSMISSION SLIPS. I'M AT 80K MILES. I THOUGHT I COULD DETERMINE WHICH GEARS IT'S SLIPPING BUT AT TIMES IT'S BEEN BETWEEN 2 &3, 3&4. THE CAR WILL REV HIGH ON RPMS WITH OUT CORRELATING SPEED AND THEN CATCH. JERKS BETWEEN GEARS AT TIMES. I FEEL SO UNSAFE IN THIS HYUNDAI AND I DON'T I CAN AFFORD THE COST. I KNOW IT'S NOT FROM M…
Read full complaint
TRANSMISSION SLIPS. I'M AT 80K MILES. I THOUGHT I COULD DETERMINE WHICH GEARS IT'S SLIPPING BUT AT TIMES IT'S BEEN BETWEEN 2 &3, 3&4. THE CAR WILL REV HIGH ON RPMS WITH OUT CORRELATING SPEED AND THEN CATCH. JERKS BETWEEN GEARS AT TIMES. I FEEL SO UNSAFE IN THIS HYUNDAI AND I DON'T I CAN AFFORD THE COST. I KNOW IT'S NOT FROM MY DRIVING.
TL* THE CONTACT OWNED A 2012 HYUNDAI GENESIS. THE CONTACT STATED THAT WHILE ON A HIGHWAY STATIONERY IN TRAFFIC, THE VEHICLE BEHIND HIM CRASHED INTO THE BACK OF HIS VEHICLE. THE CONTACT'S VEHICLE THEN COLLIDED WITH STOPPED VAN IN FRONT OF HIM; THAT VAN ALSO HIT THE VEHICLE IN FRONT OF IT AS WELL. THE AIR BAGS DID NOT DEPLOY UPON …
Read full complaint
TL* THE CONTACT OWNED A 2012 HYUNDAI GENESIS. THE CONTACT STATED THAT WHILE ON A HIGHWAY STATIONERY IN TRAFFIC, THE VEHICLE BEHIND HIM CRASHED INTO THE BACK OF HIS VEHICLE. THE CONTACT'S VEHICLE THEN COLLIDED WITH STOPPED VAN IN FRONT OF HIM; THAT VAN ALSO HIT THE VEHICLE IN FRONT OF IT AS WELL. THE AIR BAGS DID NOT DEPLOY UPON IMPACT. THE CONTACT'S CHEST HIT THE STEERING WHEEL AND THE CONTACT'S HEAD BROKE THE HEAD REST. HE RECEIVED MEDICAL ATTENTION AT THE SCENE AND WAS TRANSPORTED TO THE HOSPITAL. THE CONTACT WAS TREATED FOR A CHEST CONTUSION AND BRUISING TO HIS NECK AREA. INJURIES TO THE OTHER VEHICLES OCCUPANTS WERE UNKNOWN. A POLICE REPORT WAS FILED. AFTER BEING RELEASED FROM THE HOSPITAL, THE CONTACT WAS ABLE TO DRIVE THE VEHICLE TO AN INDEPENDENT BODY SHOP AND WAS LATER DEEMED TOTALED BY A MECHANIC. THE MANUFACTURER NOR A DEALER HAVE BEEN NOTIFIED OF THE FAILURE. UPON, INVESTIGATION THE CONTACT LINKED NHTSA CAMPAIGN NUMBER: 16V722000 (AIR BAGS) WITH HIS FAILURE. THE FAILURE MILEAGE WAS 71,244.
AT APPROXIMATELY 10:30 PM. WHILE DRIVING ON HWY AT FAIRLY GOOD SPEED OF 73-75 MPH, WHILE ON CRUISE CONTROL, THE ENGINE DIED AND STEERING BECAME DIFFICULT TO NONE AT ALL, ALL WHILE ENGINE WAS COMPLETELY OFF. CAR COULD NOT BE STARTED AGAIN. VEHICLE IS CURRENTLY NON-OPERABLE AND PARKED. IT APPEARS I AM THE THIRD OWNER OF THE IS …
Read full complaint
AT APPROXIMATELY 10:30 PM. WHILE DRIVING ON HWY AT FAIRLY GOOD SPEED OF 73-75 MPH, WHILE ON CRUISE CONTROL, THE ENGINE DIED AND STEERING BECAME DIFFICULT TO NONE AT ALL, ALL WHILE ENGINE WAS COMPLETELY OFF. CAR COULD NOT BE STARTED AGAIN. VEHICLE IS CURRENTLY NON-OPERABLE AND PARKED. IT APPEARS I AM THE THIRD OWNER OF THE IS VEHICLE. YOUR ASSISTANCE IS APPRECIATED.
WHEN TURNING STEERING WHEEL A NUMBER OF THINGS CAN HAPPEN, RADIO TURNS OFF,STEERING LOCKS UP. ALL DASH LIGHTS COME ON AND POWER BATT LIGHT LIGHTS UP. HAS STALLED IN INTERSECTION WHEN TURNING. TRANS SHIFTS HARD AND SLIPS INTO GEAR WHEN ON A LONG DRIVE
WHEN IN MOTION, THE VEHICLE STARTS TO MAKE A CLANKING SOUND REPETITIVLY AS IF IT WAS ON A ROTATION. IT'S LIKE A METRONOME BEST AT 128BPM
THE BRAKE PEDAL OF MY CAR IS SOFT AND DEEP, AND THE BRAKING IS NOT DONE PROPERLY. AFTER ABOUT A MONTH AND A HALF, THE SYMPTOMS APPEARED AND I CHANGED THE BRAKE PADS. EVERY DAY DRIVING IS A CONTINUATION OF TENSION. I WENT TO THE DESIGNATED SERVICE CENTER AND INSPECTED IT. DURING THE RE-RUN, THE SAME PHENOMENON CONTINUED, AND AFT…
Read full complaint
THE BRAKE PEDAL OF MY CAR IS SOFT AND DEEP, AND THE BRAKING IS NOT DONE PROPERLY. AFTER ABOUT A MONTH AND A HALF, THE SYMPTOMS APPEARED AND I CHANGED THE BRAKE PADS. EVERY DAY DRIVING IS A CONTINUATION OF TENSION. I WENT TO THE DESIGNATED SERVICE CENTER AND INSPECTED IT. DURING THE RE-RUN, THE SAME PHENOMENON CONTINUED, AND AFTER A WEEK AGAIN, I HAD TO CHANGE THE ABS MODULE. HOW MUCH OF AN ABS MODULE DOES IT HAVE GROUNDED LIKE A BRAKE PAD? I CAN'T UNDERSTAND IT. I LOOKED AT THE INTERNET AND THE MODEL I WAS RIDING WAS SUBJECT TO RECALL.
I OWN A 2012 HYUNDAI GENESIS AND EXPERIENCE A VERY LOW GRIP ON MY BRAKE PEDAL. IT HAS JUST BEEN CONFIRMED FROM A HYUNDAI DEALERSHIP THAT THE HECU IS BAD AND NEEDS TO BE REPLACED (11/20/19). HYUNDAI HAS RECALLED CERTAIN MODEL YEAR 2009-2012 GENESIS SEDANS UNDER RECALL 114 OR NHTSA CAMPAIGN 13V489 FOR THE HECU. I HAVE BEEN TOL…
Read full complaint
I OWN A 2012 HYUNDAI GENESIS AND EXPERIENCE A VERY LOW GRIP ON MY BRAKE PEDAL. IT HAS JUST BEEN CONFIRMED FROM A HYUNDAI DEALERSHIP THAT THE HECU IS BAD AND NEEDS TO BE REPLACED (11/20/19). HYUNDAI HAS RECALLED CERTAIN MODEL YEAR 2009-2012 GENESIS SEDANS UNDER RECALL 114 OR NHTSA CAMPAIGN 13V489 FOR THE HECU. I HAVE BEEN TOLD, HOWEVER, THAT MY VIN DOES NOT QUALIFY FOR THE SAFETY REPAIR. I FIND IT HIGHLY UNUSUAL THAT I AM EXPERIENCING THE IDENTICAL PROBLEM THAT SO MANY OTHER GENESIS SEDANS HAVE FACED, YET AM BEING DENIED THE NECESSARY REPAIR. I AM ASKING THAT MY VIN BE INCLUDED IN THE RECALL AS I AM VERY CONCERNED FOR MY SAFETY AT THIS POINT. KEEPING IN MIND THE SAFETY OF OTHERS AS WELL, ALL GENESIS SEDANS MADE DURING 2009 AND 2012 SHOULD BE RE-LOOKED AT AGAIN. IT IS A $3000 FIX AND I CANNOT TELL YOU HOW UNFAIR IT IS TO KNOW THAT OTHER HYUNDAI GENESIS OWNERS HAVE HAD THEIR HECU'S REPLACED UNDER THE RECALL. WHY IS THEIR SAFETY MORE IMPORTANT THAN MINE?
GENESIS STALLS AT SLOW SPEEDS EITHER TURNING FOR GOING STRAIGHT. REPLACED THROTTLE BODY, BUT STILL STALLS. ALSO HAS TROUBLE STARTING SOMETIMES. BATTERY IS NEW.
ON OCTOBER 23RD, 2019, THE BRAKES ON MY 2012 HYUNDAI GENESIS R-SPEC SEDAN SUDDENLY FAILED WITH THE BRAKE PEDAL GOING ALL THE WAY TO THE FLOOR BEFORE THE VEHICLE EVENTUALLY STOPPED LUCKILY AVOIDING AN ACCIDENT. I WAS DRIVING ON THE HIGHWAY. THE VEHICLE HAS 79K MILES. I THEN TOOK THE CAR TO THE HYUNDAI DEALER IN ST. LOUIS PARK,…
Read full complaint
ON OCTOBER 23RD, 2019, THE BRAKES ON MY 2012 HYUNDAI GENESIS R-SPEC SEDAN SUDDENLY FAILED WITH THE BRAKE PEDAL GOING ALL THE WAY TO THE FLOOR BEFORE THE VEHICLE EVENTUALLY STOPPED LUCKILY AVOIDING AN ACCIDENT. I WAS DRIVING ON THE HIGHWAY. THE VEHICLE HAS 79K MILES. I THEN TOOK THE CAR TO THE HYUNDAI DEALER IN ST. LOUIS PARK, MN AND THEY DETERMINED THAT THE BRAKE MASTER CYLINDER WAS FAULTY AND REPLACED. THE DIAGNOSIS AND REPAIR DID NOT FIX THE ISSUE AS THE BRAKE PEDAL WAS STILL SPONGY AND GOING TO THE FLOOR INTERMITTENTLY. I WILL BE TAKING THE CAR BACK TO THE DEALER TO HAVE THEM FIX IT CORRECTLY. WHILE RESEARCHING THE ISSUE, I HAVE FOUND THAT MULTIPLE OTHER OWNERS OF THE SAME CAR HAVE EXPERIENCED THIS ISSUE AND THE DEALER HAD TO REPLACE THE ABS HYDRAULIC ELECTRONIC CONTROL UNIT (HECU) AS IT CONTAINED CORROSION WITHIN THE UNIT DUE TO BAD DESIGN WHICH CAUSES HYDRAULIC BRAKING FAILURE TO OCCUR AT ANY TIME. THIS CAMPAIGN/RECALL BELOW OUTLINES THE ISSUE WHICH I AM GOING TO PRESENT TO THE DEALER TO FIX CORRECTLY AS I AM STILL UNDER WARRANTY. TO ME, THIS IS A LIFE OR DEATH TYPE FAILURE AND COULD RESULT IN INJURIES. HYUNDAI SHOULD BE RESPONSIBLE FOR REPLACING ALL ABS HECU BEFORE LIVES ARE LOST FOR ALL 2009-2012 HYUNDAI GENESIS, NOT JUST SOME VINS THAT THEY DEEMED TROUBLESOME. THEY SHOULD TAKE RESPONSIBILITY FOR ALL CARS AND IMMEDIATELY CONTACT THEIR OWNERS. HYUNDAI RECALL - CAMPAIGN 12-01-052 TSB: BH GENESIS SEDAN HECU INSPECTION AND BRAKE FLUID REPLACEMENT (RECALL 114) ORIGINAL RECALL FROM THE NHTSA MANUFACTURER'S REPORT DATE OCTOBER 29, 2013 NHTSA ACTION NUMBER PE13033 POTENTIAL NUMBER OF UNITS AFFECTED 43,500
Official recalls
216V117000 · Visibility:windshield Wiper/washer:motor
Feb 29, 2016
Hyundai Motor America (Hyundai) is recalling certain model year 2012 Genesis vehicles manufactured August 1, 2011, to April 30, 2012, and 2011-2013 Equus vehicles manufactured July 10, 2011, to June 12, 2012. The windshield wiper motor cover seal on the affected vehicles may degrade allowing corrosion on the wiper motor's circuit board. The corrosion can cause intermittent or total loss of wiper function.
Consequence & remedy
Consequence: Inoperative wipers during inclement weather can decrease driver visibility, increasing the risk of a crash.
Remedy: Hyundai will notify owners, and dealers will replace the wiper motor cover and seal, free of charge. The recall began on April 22, 2016. Owners may contact Hyundai customer service at 1-800-633-5151. Hyundai's number for this recall is 140.
13V489000 · Service Brakes, Hydraulic:fluid
Oct 29, 2013
Hyundai is recalling certain model year 2009-2012 Genesis vehicles manufactured April 30, 2008, through March 28, 2012. The vehicles may contain brake fluid which does not protect against corrosion of the Hydraulic Electronic Control Unit (HECU).
Consequence & remedy
Consequence: If the module corrodes, reduced brake effectiveness may result, increasing the risk of a crash.
Remedy: Hyundai will notify owners and instruct them to bring their vehicle to a dealer for service. Hyundai will inspect the HECU module for proper operation, and will replace the modules as necessary. Hyundai will replace the factory brake fluid in those vehicles that have not previously had the factory brake fluid replaced. These repairs will be done free of charge. The recall began on December 24, 2013. Owners may contact Hyundai at 1-800-633-5151 or by email at consumeraffairs@hmausa.com. Hyundai's recall number is 114.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE13033 · Brake Hydraulic Control Module Failure
Opened Oct 17, 2013 · Closed Apr 4, 2014
Status: closed (inferred from source dates) · Service Brakes, Hydraulic; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354
Additional source detail variants (3)
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354
Service Brakes, Hydraulic
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354