When the car gets wet, it sends my dashboard lights flashing, and I’m able to put the car in gear without stepping on the brake, I brought it to numerous of Honda dealerships and other mechanical shops, and they are undetermined to find the cause
2011 Hyundai Genesis
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2011 Hyundai Genesis do not stand out strongly from the model-year median of 109.
About this comparison →How this year compares
Owner complaints by model year
Compare all Genesis years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
99 reports with mileage · 23 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 19 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Vehicle Speed Control. Review the 16 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 15 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
Electrical System complaints
19 reportsHeadlights will intermittently flicker off for several seconds when using turn signal. I understand this is already noted in TSB 20-BE-009H
THE CAR WAS PARKED (NOT RUNNING OR MOVING) IN AN OPEN AIR GROCERY STORE PARKING LOT. I WAS IN THE GROCERY STORE FOR APPROXIMATELY 20 MINUTES AND CAME OUT TO FIND A CROWD AND A FIRE CREW WHO HAD JUST PUT OUT THE FIRE IN THE HOOD AREA OF MY CAR. I HAVE PHOTOS OF THE CAR BUT THEY ARE ON MY PHONE AND I DON'T KNOW HOW TO SEND THEM …
Read full complaint
THE CAR WAS PARKED (NOT RUNNING OR MOVING) IN AN OPEN AIR GROCERY STORE PARKING LOT. I WAS IN THE GROCERY STORE FOR APPROXIMATELY 20 MINUTES AND CAME OUT TO FIND A CROWD AND A FIRE CREW WHO HAD JUST PUT OUT THE FIRE IN THE HOOD AREA OF MY CAR. I HAVE PHOTOS OF THE CAR BUT THEY ARE ON MY PHONE AND I DON'T KNOW HOW TO SEND THEM TO COMPUTER.
IN 2016, I FILED COMPLAINT # 1084551 REGARDING THE ENGINE SHUTTING DOWN WHEN MY CAR HAD ONLY 23000 MILES. UNFORTUNATELY NEITHER THIS AGENCY OR HYUNDAI USA GAVE ME THE AN EXPLANATION AS TO WHY THIS HAPPENED, AND HAPPY HYUNDAI KEPT MY CAR FOR 43 DAYS TO REPLACE VARIOUS ENGINE PARTS. NOW IN 2019, THE CONNECTOR TO THE COOLANT FAN ME…
Read full complaint
IN 2016, I FILED COMPLAINT # 1084551 REGARDING THE ENGINE SHUTTING DOWN WHEN MY CAR HAD ONLY 23000 MILES. UNFORTUNATELY NEITHER THIS AGENCY OR HYUNDAI USA GAVE ME THE AN EXPLANATION AS TO WHY THIS HAPPENED, AND HAPPY HYUNDAI KEPT MY CAR FOR 43 DAYS TO REPLACE VARIOUS ENGINE PARTS. NOW IN 2019, THE CONNECTOR TO THE COOLANT FAN MELTED WHICH IS RELATED TO THE ECM MODULE. THERE WAS AN ECM RECALL AT THE TIME IN MARCH 2016 BUT IT APPEARS THAT THE SPECIFICATIONS OF THE RECALL DIDNT ADDRESS/FIX THE PROBLEM. FURTHER, IT APPEARS THAT THE PROBLEM I ENCOUNTERED IN 2016, THEE ECM RECALL AND THE PROBLEM I HAVE ENCOUNTERED ON JULY 25, 2019 ARE VERY RELATED. I CAN ONLY HOPE AND IMPLORE THOS AGENCY TO LOOK FURTHER INTO THESE ISSUES. THE CAR WAS IN MOTION WHEN THE ENGINE LIGHT CAME ON. TOOK TO THE DEALER AND THE DIAGANOSTIC I WAS GIVEN SAID THEE THERMOSTATE NEEDED TO BE REPLACED ALONG WITH THE TEMPERATURE SENSOR AND A COOLANT FLUSH. ALSO TOLD THE A/C COMPRESSOR AND HOSE NEEDED TO BE REPLACED. ON AUGUST 14TH THE THERMOSTATE, SENSOR AND COOLANT FLUSH WAS COMPLETED BY HAPPY HYUNDAI BUT THE ENGINE CAME BACK ON THE SAME DAY AFTER I DROVE ON THE EXPRESSWAY. I TOOK MY CAR INTO ANOTHER O. AUGUST 20, 2019 AND WAS TOLD MY CAR WASS MISSED DIAGNOSED AND THAT THE COOLANT FAN CONTROLLER HAD SHORTED AND THE CONNECTOR TO THAT COMPONENT HAD MELTED. THIS IS ALL RELATED TO THE ECM MODULE.
RECALL ON CAR BACK IN 2014 FOR BRAKE FAILURE. IMPROPER FLUID USED CAUSING ABS ASSIST MODULE TO FAIL RESULTING IN SOFT BREAK PEDAL. PURCHASED VEHICLE IN 2014 USED AND NEVER TOLD OF THIS ISSUE AFTER PURCHASING VEHICLE NOR NEVER SENT ANY INFO. ELECTRICAL PROBLEMS , DRIVE SEAT WONT RESPOND , WIND SHIELD WIPERS RANDOMLY TURNING ON .…
Read full complaint
RECALL ON CAR BACK IN 2014 FOR BRAKE FAILURE. IMPROPER FLUID USED CAUSING ABS ASSIST MODULE TO FAIL RESULTING IN SOFT BREAK PEDAL. PURCHASED VEHICLE IN 2014 USED AND NEVER TOLD OF THIS ISSUE AFTER PURCHASING VEHICLE NOR NEVER SENT ANY INFO. ELECTRICAL PROBLEMS , DRIVE SEAT WONT RESPOND , WIND SHIELD WIPERS RANDOMLY TURNING ON . TAIL LIGHTS NOT WORKING ALSO ON RECALL. THIS NOTIFICATION ALSO NEVER SENT TO USE RESULTING IN THE VEHICLE BEING REAR ENDED LAST YEAR . PASSENGER SEAT HEAD REST DEPLOYED AND NOT DRIVERS. CAR WAS FIXED AND A COUPLE OF WEEKS AGO THE PASSENGER HEAD RESET DEPLOYED AGAIN HITTING MY DAUGHTER AND AT THE SAME EXPLODED AND CAME OF ITS FRAME LANDING IN THE BACK SEAT. HYUNDIA DEALER WONT DO ANYTHING OTHER THAN WHATS ON RECALL NOW.
THE VEHICLE HAS ISSUES WITH THE BLUETOOTH SOUND SYSTEM WHERE IT RANDOMLY DISCONNECTS REGARDLESS IF THE CAR IS IN MOTION OR STATIONARY. THE CAR USES A LEXICON SOUND SYSTEM. HOWEVER, THE CAR EXPERIENCES ANOTHER ISSUE WITH THE DISPLAY REGARDING SELECTING A BLUETOOTH DEVICE AND THE SCREEN APPEARS BLANK. FROM WHERE THE ISSUE DERIVES …
Read full complaint
THE VEHICLE HAS ISSUES WITH THE BLUETOOTH SOUND SYSTEM WHERE IT RANDOMLY DISCONNECTS REGARDLESS IF THE CAR IS IN MOTION OR STATIONARY. THE CAR USES A LEXICON SOUND SYSTEM. HOWEVER, THE CAR EXPERIENCES ANOTHER ISSUE WITH THE DISPLAY REGARDING SELECTING A BLUETOOTH DEVICE AND THE SCREEN APPEARS BLANK. FROM WHERE THE ISSUE DERIVES IS UNKNOWN TO PIN POINT. ONE POSSIBILITY IS THAT THE SYSTEM READS A CD RANDOMLY WITHOUT A DISK BEING INSIDE AND IT RESETS THE SYSTEM.
WHILE DRIVING VEHICLE, THE LIGHTS SOME TIMES FLASH AND/OR THE VEHICLE STOPS RUNNING EVEN AT HIGHWAY SPEEDS.
TL* THE CONTACT OWNS A 2011 HYUNDAI GENESIS. WHILE DRIVING 20 MPH, THE VEHICLE STALLED WITHOUT WARNING. THE CONTACT STATED THAT THE FAILURE ALSO OCCURRED WHILE REVERSING. EACH TIME, THE CONTACT WAS ABLE TO CORRECT THE FAILURE BY OPENING AND CLOSING THE DRIVER'S DOOR. THE DEALER AND MANUFACTURER WERE NOT MADE AWARE OF THE FAILURE…
Read full complaint
TL* THE CONTACT OWNS A 2011 HYUNDAI GENESIS. WHILE DRIVING 20 MPH, THE VEHICLE STALLED WITHOUT WARNING. THE CONTACT STATED THAT THE FAILURE ALSO OCCURRED WHILE REVERSING. EACH TIME, THE CONTACT WAS ABLE TO CORRECT THE FAILURE BY OPENING AND CLOSING THE DRIVER'S DOOR. THE DEALER AND MANUFACTURER WERE NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 80,000. THE VIN WAS NOT AVAILABLE.
MY TAIL LIGHTS AND BRAKE LIGHTS STOPPED WORKING. REPLACED TAIL LIGHT SWITCH.DIDN'T SOLVE THE PROBLEM.
"TAKATA RECALL" > MY 2011 HYUNDAI GENESIS SEDAN HAS BEEN GRANTING MANY PROBLEMS WITH STARTING. SOMETIMES IT WILL START UP IMMEDIATELY, THEN SOMETIMES IT WILL START SLOWLY OR NOT START AT ALL AND SIMPLY REVERT TO A CLICKING AND NO START. THIS SEEMS TO ALSO BE GIVING MANY OTHER DRIVERS PROBLEMS AS I LOOK ONLINE. PLEASE UPDATE THI…
Read full complaint
"TAKATA RECALL" > MY 2011 HYUNDAI GENESIS SEDAN HAS BEEN GRANTING MANY PROBLEMS WITH STARTING. SOMETIMES IT WILL START UP IMMEDIATELY, THEN SOMETIMES IT WILL START SLOWLY OR NOT START AT ALL AND SIMPLY REVERT TO A CLICKING AND NO START. THIS SEEMS TO ALSO BE GIVING MANY OTHER DRIVERS PROBLEMS AS I LOOK ONLINE. PLEASE UPDATE THIS INFORMATION AS I DO NOT WISH TO BE LEFT STRANDED. THE VEHICLE IS OFF WHEN THIS PROBLEM OCCURS.
Official recalls
314V713000 · Exterior Lighting:brake Lights:switch
Nov 7, 2014
Hyundai Motor America (Hyundai) is recalling certain 2009-2011 Hyundai Genesis vehicles manufactured April 30, 2008, to November 21, 2010, and 2011 Hyundai Equus vehicles manufactured July 31, 2010, to November 21, 2010. Due to a circuit failure, the stop lamps in the affected vehicles may not illuminate.
Consequence & remedy
Consequence: A following vehicle may not recognize that the vehicle is slowing or coming to a stop if the stop lamps on the vehicle do not illuminate as expected. There is an increased risk of a rear-end crash as a result.
Remedy: Hyundai will notify owners, and dealers will repair the stop lamp switch circuit, free of charge. Hyundai issued an interim notification to owners on January 6, 2015. The recall began on March 23, 2015. Owners may contact Hyundai customer service at 1-855-671-3059. Hyundai's number for this recall is 125.
13V489000 · Service Brakes, Hydraulic:fluid
Oct 29, 2013
Hyundai is recalling certain model year 2009-2012 Genesis vehicles manufactured April 30, 2008, through March 28, 2012. The vehicles may contain brake fluid which does not protect against corrosion of the Hydraulic Electronic Control Unit (HECU).
Consequence & remedy
Consequence: If the module corrodes, reduced brake effectiveness may result, increasing the risk of a crash.
Remedy: Hyundai will notify owners and instruct them to bring their vehicle to a dealer for service. Hyundai will inspect the HECU module for proper operation, and will replace the modules as necessary. Hyundai will replace the factory brake fluid in those vehicles that have not previously had the factory brake fluid replaced. These repairs will be done free of charge. The recall began on December 24, 2013. Owners may contact Hyundai at 1-800-633-5151 or by email at consumeraffairs@hmausa.com. Hyundai's recall number is 114.
13V113000 · Exterior Lighting:brake Lights:switch
Apr 1, 2013
Hyundai Motor Company (Hyundai) is recalling certain model year 2006-2009 Accent, model year 2007-2011 Azera, Sonata and Sante Fe,2006-2011 Tucson, 2009-2011 Elantra Touring, 2007-2010 Elantra, 2008-2011 Veracruz, 2009-2011 Genesis, 2010-2011 Genesis Coupe, 2007-2008 Entourage, and 2006-2008 Tiburon vehicles. Originally, in April 2013, Hyundai recalled 1,059,824 model year 2007-2009 Accent and Tucson, model year 2007-2010 Elantra, model year 2007-2011 Santa Fe, model year 2008-2009 Veracruz, model year 2010-2011 Genesis Coupe, and model year 2011 Sonata vehicles. In September 2013, Hyundai informed the agency that it was adding more vehicles to this campaign, representing an additional 652,512 units. The total number of vehicles being recalled is now 1,712,336. In the affected vehicles, the stop lamp switch may malfunction. A malfunctioning stop lamp switch may cause the brake lights to not illuminate when the brake pedal is depressed or may cause an inability to deactivate the cruise control by depressing the brake pedal. Additionally, a malfunctioning stop lamp switch may also result in intermittent operation of the push-button start feature, affect the operation of the brake transmission shift interlock feature, preventing the shifter from being moved out of the PARK position and cause the Electronic Stability Control (ESC) malfunction light to illuminate.
Consequence & remedy
Consequence: Failure to illuminate the stop lamps during braking or inability to disengage the cruise control could increase the risk of a crash. Additionally, when the ignition is in the 'ON' position, the transmission shifter may be able to be moved out of Park without first applying the brake. This may lead to unintentional movement of the car which may increase the risk of a crash.
Remedy: Hyundai will notify owners, and dealers will replace the stop lamp switch, free of charge. The safety recall began on April 22, 2013. Owners may contact Hyundai at 1-800-633-5151. Hyundai's recall campaign number is 110.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE13033 · Brake Hydraulic Control Module Failure
Opened Oct 17, 2013 · Closed Apr 4, 2014
Status: closed (inferred from source dates) · Service Brakes, Hydraulic; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354
Additional source detail variants (3)
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354
Service Brakes, Hydraulic
On October 28, 2013, Hyundai Motor Company (Hyundai) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect in the braking system of approximately 43,500 model year (MY) 2009 through 2012 Hyundai Genesis sedans (NHTSA Recall No. 13V-489).The Hyundai report indicates that the recalled vehicles may contain brake fluid that does not sufficiently inhibit corrosion on the zinc plating of control valve armatures in the Hydraulic Electronic Control Unit (HECU) module. The DIR indicated that, over time, the build-up of corrosion products may affect operation of HECU control valves, resulting in a low/soft brake pedal with reduced brake effectiveness, which may increase the risk of a crash.In October 2011, the HECU supplier notified Hyundai that the brake fluid used in production plants was causing corrosion of valve armatures in the control module.The supplier changed the coating of the valve armatures in late March 2012 to correct the problem in production vehicles.Hyundai's recall includes Genesis vehicles produced prior to the implementation of the HECU change.In March 2013, Hyundai initiated a Service Campaign (TL6) to replace brake fluid in the subject vehicles with brake fluid with better corrosion resistance properties.According to Hyundai's DIR letter, after PE13-033 was opened, the company noted that some of the vehicles serviced in the TL6 campaign subsequently required HECU replacement.This was an indication that internal corrosion had progressed enough to affect valve operation and brake performance, prompting Hyundai to conduct a safety recall.Hyundai's repair procedures for 13V-489 require brake system flushing and replacement in all recalled vehicles with a new fluid containing the necessary corrosion inhibitor.In addition, for vehicles produced prior to June 1, 2010, dealers will perform an inspection procedure to verify that the HECU is functioning properly and replace units that do not meet the test requirements.Hyundai indicated that, based on analysis of claim data, only vehicles produced prior to June 1, 2010 have been in service long enough to require the additional inspection/replacement of the HECU. Analysis of failure data reported to NHTSA and provided by Hyundai in response to ODI's information request letter for PE13-033 identified 756 complaints and 1,683 warranty claims for 30,114 subject vehicles produced prior to June 1, 2010, resulting in a complaint rate of 25.1 incidents per thousand vehicles (IPTV) and a claim rate of 5.6 percent.The MY 2009 vehicles, with the longest exposure times, experienced the highest complaint (33.5 IPTV) and warranty (7.0 percent) rates.For the 45,639 subject vehicles produced after June 1, 2010, ODI identified 13 complaints and 34 warranty claims, resulting in a complaint rate of 0.3 IPTV and a warranty claim rate of 0.1 percent, indicating that the brake fluid corrosion concern had not progressed far enough to result in significant rates of brake system performance symptoms in those vehicles.This investigation is closed.ODI will continue to monitor complaints to evaluate the effectiveness of Hyundai's recall.The VOQs noted in the Failure Report are: 10569231, 10560898, 10560495, 10559360, 10558279, 10558264, 10556964, 10556631, 10556577, 10556322, 10554988, 10554802, 10554122, 10552958, 10551817, 10551157, 10551110, 10551092, 10550791, 10550773, 10550431, 10549750, 10549634, 10549629, 10549567, 10549402, 10549376, 10549270, 10549228, 10549186, 10549021, 10548903, 10548823, 10548791, 10548737, 10548722, 10548716, 10548705, 10546565, 10544803, 10543663, 10542962, 10541959, 10541741, 10538208, 10537934, 10536652, 105354
Illustration