Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 18 of 84 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
Engine And Engine Cooling. Review the 42 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Tires. Review the 16 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Power Train. Review the 6 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
1 crash reports0 fire reports3 injury reports
What owners actually said
84 reports
Mileage unknown · Jun 27, 2021
Service Brakes
On 06/26/2021, Approx 4pm. Traffic heavy. Speed 20 mph or less. This caused consistent brake use. Rear brakes locked up. I was very close to the right edge of the road and bike stopped. I quickly activated emergency flashers and avoided any incident. This bike has ABS. There was a service recall performed about 4 yrs ago- at…
Read full complaint
On 06/26/2021, Approx 4pm. Traffic heavy. Speed 20 mph or less. This caused consistent brake use. Rear brakes locked up. I was very close to the right edge of the road and bike stopped. I quickly activated emergency flashers and avoided any incident. This bike has ABS. There was a service recall performed about 4 yrs ago- at Barneys MC shop, St Petersburg- related to brakes. I was able to shut off the bike twice. Pumped/tapped FR/R brakes twice and the brakes finally released. No further incident. Will have bike inspected tomorrow. No warning lamps. This bike has very low mileage at 21,000.
NHTSA ODI #11422482
28,500 miles · Jun 22, 2017
Suspension
CHAMPION SIDE CAR TRIKE KIT FRAME FAILURE ON A GL1800 WITH ONLY 28.K MILES AND NO ACCIDENTS.
NHTSA ODI #11000691
52 miles · Jun 20, 2017
Service BrakesInjury
I BOUGHT A 1800 HONDA GOLDWING TOURING BIKE 2-3 YEARS AGO HAD A BRAKE RECALL AND STILL DO? MINE WAS WORKED ON TWICE? AFTER I BOUGHT I DROVE IT 54 MILES THE REAR WHEEL LOCKED UP PULLING ME IN THE DITCH? FLIPPING THE BIKE AND SENDING IT END OVER END TOTAL? THAT WAS ALL DON,T BEFORE I GOT OUT OF THE ER AND HOSPITOL....UPDATED 06/21…
Read full complaint
I BOUGHT A 1800 HONDA GOLDWING TOURING BIKE 2-3 YEARS AGO HAD A BRAKE RECALL AND STILL DO? MINE WAS WORKED ON TWICE? AFTER I BOUGHT I DROVE IT 54 MILES THE REAR WHEEL LOCKED UP PULLING ME IN THE DITCH? FLIPPING THE BIKE AND SENDING IT END OVER END TOTAL? THAT WAS ALL DON,T BEFORE I GOT OUT OF THE ER AND HOSPITOL....UPDATED 06/21/17 *BF THE CONSUMER STATED THE VEHICLE WAS TOTALED AND SOLD. UPDATED 08/04/2017*JS
NHTSA ODI #11000149
179,971 miles · Apr 4, 2017
Unknown Or Other
ON 3/27/17 DURING ROUTINE MAINTENANCE AND CLEANING IN MY GARAGE, I REMOVED THE SIDE COVERS AND FOUND THE FRAME WAS BROKEN COMPLETELY APART ON BOTH SIDES OF THE MOTORCYCLE. FRAME BRAKE WAS IN THE LOWER TUBE SECTION OF THE REAR TRIANGLE OF MAIN FRAME DIRECTLY AFT OF THE WELD. THIS IS A KNOWN WEAK SPOT, SINCE HONDA REINFORCED THI…
Read full complaint
ON 3/27/17 DURING ROUTINE MAINTENANCE AND CLEANING IN MY GARAGE, I REMOVED THE SIDE COVERS AND FOUND THE FRAME WAS BROKEN COMPLETELY APART ON BOTH SIDES OF THE MOTORCYCLE. FRAME BRAKE WAS IN THE LOWER TUBE SECTION OF THE REAR TRIANGLE OF MAIN FRAME DIRECTLY AFT OF THE WELD. THIS IS A KNOWN WEAK SPOT, SINCE HONDA REINFORCED THIS AREA OF THE ALUMINUM FRAME IN MID-2004. THIS BREAK WAS REPORTED TO HONDA POWERSPORTS CUSTOMER SERVICE IN TORRANCE, CA ON 3/28/17. HAD THE BROKEN FRAME INSPECTED AND PHOTOGRAPHED BY AUTHORIZED HONDA SERVICE MANAGER 3/31/17. NOW WAITING TO HEAR FROM HONDA.
NHTSA ODI #10970451
23,153 miles · Jul 19, 2016
Service Brakes
HAD BRAKE RECALL WORK DONE AT HONDA DEALERSHIP. AFTER THAT & HAS TEMP GOT HOTTER I DEVELOPED A EXTREMELY VIOLENT BRAKE SHUTTER.RETURNED IT TO THE DEALERSHIP. THEY NOTIFIED HONDA AND ATTEMPTED TO REWORK THE BRAKES BUT DID NOT FIX THE PROBLEM. I DID SOME RESEARCH ON THE INTERNET GOLDWING BRAKE SHUDDERING & FOUND OUT I WAS NOT THE …
Read full complaint
HAD BRAKE RECALL WORK DONE AT HONDA DEALERSHIP. AFTER THAT & HAS TEMP GOT HOTTER I DEVELOPED A EXTREMELY VIOLENT BRAKE SHUTTER.RETURNED IT TO THE DEALERSHIP. THEY NOTIFIED HONDA AND ATTEMPTED TO REWORK THE BRAKES BUT DID NOT FIX THE PROBLEM. I DID SOME RESEARCH ON THE INTERNET GOLDWING BRAKE SHUDDERING & FOUND OUT I WAS NOT THE ONLY ONE HAVING THIS PROBLEM & HONDA IS AWARE OF IT.CALLED HONDA CS TOLD THEM WHAT IT WAS DOING. THEY INFORM ME IF I READ MY OWNER MANUAL ON BRAKE OPERATIONS THAT IT'S OPERATOR ERROR .I HAVE OWNED THIS BIKE SINCE IT WAS NEW. IT DOES NOT MATTER WHAT BRAKE COMBINATION YOU USE FRONT/REAR /SIMULTANEOUSLY IT CREATES THE SHUTTER. THIS STARTS WHEN THE TEMP GETS ABOVE 80 DEGREES IT DOES NOT MATTER SLOW OR HIGH SPEEDS IN CURVES OR TURNING A CORNER OR ONTO A PARKING LOT YOU HAVE TO RELEASE THE BRAKE TO GET IT TO STOP. THIS PROBLEM DID NOT START UNTIL AFTER THE RECALL WORK WAS DONE.THERE IS STILL SOME KIND OF BRAKE PROBLEM WITH THE GOLDWING GL 1800. I GUESS IT WILL TAKE SOMEONE GETTING KILLED BEFORE HONDA DOES SOMETHING ABOUT. I WISH YOU'D DO SOME RESEARCH ON THE BRAKE SHUTTERING. JUST LOOK UP GOLDWING BRAKE SHUTTER IT STARTED 2002 AND GOES TO 2015. I DON'T KNOW IF ANYONE ELSE HAS FILED A COMPLAINT?
NHTSA ODI #10885934
156,000 miles · Feb 29, 2016
Electrical System
ENGINE STOP SWITCH IS OVERLY SENSITIVE. IF MOTORCYCLE HITS A BUMP THE ENGINE MAY SHUT OFF. IF SWITCH IS TOUCHED IT WILL STOP ENGINE.
NHTSA ODI #10838942
60,000 miles · Apr 7, 2011
Electrical SystemEquipment
I PURCHASED MY 2001 GOLDWING 1800 USED FROM A LOCAL DEALER IN PLAINFIELD, CT. THE GOLDWING WAS SOLD TO ME WITH THE STEREO SYSTEM INSTALLED WHICH INCLUDED THE 5 DISC CD CHANGER UNDER THE REAR TRUNK. FROM DAY 1 I HAD PROBLEMS WITH THIS CD CHANGER NOT WORKING CORRECTLY, BECOMING JAMMED UP WITH ALL 5 DISCS IN ONE SLOT, ETC. I HAD T…
Read full complaint
I PURCHASED MY 2001 GOLDWING 1800 USED FROM A LOCAL DEALER IN PLAINFIELD, CT. THE GOLDWING WAS SOLD TO ME WITH THE STEREO SYSTEM INSTALLED WHICH INCLUDED THE 5 DISC CD CHANGER UNDER THE REAR TRUNK. FROM DAY 1 I HAD PROBLEMS WITH THIS CD CHANGER NOT WORKING CORRECTLY, BECOMING JAMMED UP WITH ALL 5 DISCS IN ONE SLOT, ETC. I HAD TAKEN OUT THE EXTENDED WARRANTY FROM THE DEALERSHIP BUT ALL THEY EVER TOLD ME WAS THAT THEY WERE LOOKING INTO THE PROBLEM. THEY DID PROVIDE ME WITH A PRINT OUT OF ALL OF THE WORK DONE FOR THE PREVIOUS OWNER WHICH ALSO SHOWED THE SAME ISSUE WITH THE CD CHANGER BUT THEY REPLACED IT TWICE FOR HIM YET NOTHING WAS EVER DONE TO HELP WITH MY PROBLEM EXCEPT " WE ARE LOOKING INTO THE PROBLEM." SINCE THEN THE DEALERSHIP HAS FOLDED AND A NEW OWNER IS RUNNING THE PLACE AND OF COURSE THEY ARE NOT BACKING ANYTHING THAT THE OLD DEALERSHIP DID OR SAID ( CAN NOT BLAME THEM THERE THOUGH!) I WAS TOLD BY SOMEONE THAT THERE WAS SOME KIND OF A RECALL ON THE CD CHANGER WHICH IS MADE BY PIONEER, CAN SOMEONE PLEASE TELL ME HOW TO GET THIS FIXED, REPAIRED, REPLACED, ANYTHING?? *TR
NHTSA ODI #10395158
Mileage unknown · Sep 28, 2010
Tires
METZELER ME880 MARATHON, 180/60R16, FOR HONDA GL1800 REAR TIRE OUT OF ROUND CAUSING MOTORCYCLE TO SHIMMY. TIRE WAS INSTALLED SUMMER OF 2009. SHIMMY BEGAN AFTER TIRE MILEAGE ABOUT 5,000. THERE WAS NO DETECTABLE DEFLECTION IN TIRE, BUT PROBLEM STEADILY GOT WORSE. TIRE WAS CHECKED FREQUENTLY, PRESSURE CHECKED DAILY (KEPT AT 42PSI).…
Read full complaint
METZELER ME880 MARATHON, 180/60R16, FOR HONDA GL1800 REAR TIRE OUT OF ROUND CAUSING MOTORCYCLE TO SHIMMY. TIRE WAS INSTALLED SUMMER OF 2009. SHIMMY BEGAN AFTER TIRE MILEAGE ABOUT 5,000. THERE WAS NO DETECTABLE DEFLECTION IN TIRE, BUT PROBLEM STEADILY GOT WORSE. TIRE WAS CHECKED FREQUENTLY, PRESSURE CHECKED DAILY (KEPT AT 42PSI). AT ABOUT 9500 MILES ON TIRE, SHIMMY GOT WORSE, AND TIRE FOUND TO HAVE OVER 1/2 IN. RADIAL AND AXIAL RUNOUT. THIS IS THIRD METZELER ON MY GL1800. 1ST ONE, SUMMER OF 2006, HAD SLIGHT SHIMMY FROM START, LASTED ONLY 925 MILES - BLOWOUT FROM ROAD DEBRIS. HAD THAT TIRE REPLACED BY HONDA DEALER IN FERGUS FALLS, MINNESOTA. REPLACEMENT TIRE HAD NO SHIMMY UNTIL ABOUT 800 MILES. SHIMMY WORLENED UNTIL DANGEROUS CONDITION AND TIRE REPLACED WITH DIFFERENT BRAND. E-MAIL SENT TO METZELER WITH NO RESPONSE. *TR
NHTSA ODI #10358058
93,457 miles · Apr 12, 2010
Structure
MOTORCYCLE, HONDA GOLDWING, 2001 LEFT FRAME CRACK: THERE HAVE BEEN NUMEROUS INSTANCES OF FRAMES BEING CRACKED AND UPON INSPECTION OF MY MOTORCYCLE FRAME I NOTICED THAT I HAVE THE IDENTICAL CRACK IN MY FRAME. THE CRACK IS LOCATED ADJACENT TO THE LEFT PASSENGER FOOTREST AND IS VISIBLE BY REMOVING THE REAR TIRE AND VIEWING IT FROM…
Read full complaint
MOTORCYCLE, HONDA GOLDWING, 2001 LEFT FRAME CRACK: THERE HAVE BEEN NUMEROUS INSTANCES OF FRAMES BEING CRACKED AND UPON INSPECTION OF MY MOTORCYCLE FRAME I NOTICED THAT I HAVE THE IDENTICAL CRACK IN MY FRAME. THE CRACK IS LOCATED ADJACENT TO THE LEFT PASSENGER FOOTREST AND IS VISIBLE BY REMOVING THE REAR TIRE AND VIEWING IT FROM UNDER THE BIKE. THE CRACK EXTENDS DOWN FROM A WELD THAT ATTACHES THE LOWER LEFT REAR SUPPORT TUBE TO THE CENTER SECTION OF THE FRAME. *TR
NHTSA ODI #10325068
56,300 miles · Feb 10, 2009
Structure
THE VEHICLE IS A 2001 HONDA GL1800 MOTORCYCLE WITH 56300 MILES. VEHICLE WAS RECALLED FOR POSSIBLE WELD DEFECTS IN THE FRAME SEVERAL YEARS AGO. VEHICLE PASSED INSPECTION. NO WELD DEFECTS OR CRACKS WERE FOUND AT THAT TIME. UPON DOING CLEANING AND MAINTENANCE ON THE VEHICLE OVER THE PAST 10 DAYS I DISCOVERED A CRACK IN A FRAME W…
Read full complaint
THE VEHICLE IS A 2001 HONDA GL1800 MOTORCYCLE WITH 56300 MILES. VEHICLE WAS RECALLED FOR POSSIBLE WELD DEFECTS IN THE FRAME SEVERAL YEARS AGO. VEHICLE PASSED INSPECTION. NO WELD DEFECTS OR CRACKS WERE FOUND AT THAT TIME. UPON DOING CLEANING AND MAINTENANCE ON THE VEHICLE OVER THE PAST 10 DAYS I DISCOVERED A CRACK IN A FRAME WELD. THE CRACK IS LOCATED IN THE MIDDLE OF A WELD AND EXTENDS APPROXIMATELY 1.5 INCHES. THE CRACK IS AT THE JUNCTION OF A TUBULAR PROTRUBANCE OFF THE MAIN FRAME AND TUBULAR SUPPORT FOR THE MOTORCYCLE SEAT. THE ALUMINUM TUBULAR SUPPORT IS ON THE LEFT SIDE OF THE MOTORCYCLE. I HAVE NOTIFIED AMERICAN HONDA IN CALIFORNIA. THE MOTORCYCLE IS AT THE FOX VALLEY HONDA DEALERSHIP IN AURORA, ILLINOIS. FOX VALLEY HONDA IS NOTIFYING THE DISTRICT MANAGER WHO WILL EVALUATE THE FRAME PROBLEM. *TR
American Honda Motor Co., Inc. (Honda) is recalling certain model year 2001-2010 and 2012-2015 GL1800, 2001-2005 GL1800A and 2013-2015 GL1800B motorcycles. The rear brakes of the affected motorcycles may drag after the brakes are released.
Consequence & remedy
Consequence: A rear brake that drags may increase the risk of a vehicle crash. Additionally, extended riding with the rear brake dragging could generate enough heat to result in a fire.
Remedy: Honda will notify owners, and dealers will replace the secondary brake master cylinder and the rear brake master cylinder, and flush the brake fluid, free of charge. The recall began on December 7, 2015. Owners may contact Honda customer service at 1-866-784-1870. Honda's number for this recall is JV6. Note: This recall supercedes recall 14V-472.
HONDA IS RECALLING CERTAIN MODEL YEAR 2001-2010, AND MODEL YEAR 2012 GL1800 GOLDWING MOTORCYCLES. UNDER CERTAIN CONDITIONS, THERE IS A POSSIBILITY THAT THE COMBINED BRAKING SYSTEM'S SECONDARY MASTER CYLINDER MAY CAUSE THE REAR BRAKE TO DRAG.
Consequence & remedy
Consequence: UNEXPECTED BRAKING INCREASES THE RISK OF A CRASH, AND RIDING THE MOTORCYCLE WITH THE REAR BRAKE DRAGGING MAY GENERATE ENOUGH HEAT TO CAUSE THE REAR BRAKE TO CATCH FIRE.
Remedy: HONDA WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT THE SECONDARY MASTER CYLINDER AND IF NECESSARY, REPLACE IT, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 6, 2012. OWNERS MAY CONTACT HONDA CUSTOMER SERVICE AT 1-866-784-1870.
ON SOME MOTORCYCLES, CERTAIN FRAME WELDS DO NOT MEET MANUFACTURING SPECIFICATIONS. HIGH LOADS CREATED WHEN RIDING ON ROUGH ROAD SURFACES OR THROUGH POTHOLES CAN CAUSE THE AFFECTED WELDS TO CRACK.
Consequence & remedy
Consequence: THE WELDED AREA COULD BREAK, RESULTING IN REAR SUSPENSION COLLAPSE OR LOWER CROSS MEMBER SEPARATION, INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL INSPECT AND, IF NECESSARY, REINFORCE THE WELDS ON 2001-2002 MOTORCYCLES FREE OF CHARGE. ON 2003-2004 MOTORCYCLES, THE UNITS WILL BE REPAIRED, NO INSPECTION WILL BE NECESSARY. THE RECALL BEGAN ON FEBRUARY 9, 2005. OWNERS MAY CONTACT HONDA AT 1-866-784-1870.
VEHICLE DESCRIPTION: MOTORCYCLES EQUIPPED WITH A NEWLY DESIGNED ENGINE STOP SWITCH. THE ENGINE STOP SWITCH IS SENSITIVE TO ACCIDENTAL CONTACT OR STRONG JOLTING, SUCH AS HITTING A POTHOLE OR RIDING OVER RAILROAD TRACKS,WHICH COULD CAUSE THE ENGINE TO CUT OUT MOMENTARILY OR EVEN SHUT OFF.
Consequence & remedy
Consequence: SUDDEN LOSS OF ENGINE POWER COULD LEAD TO A CRASH.
Remedy: DEALERS WILL INSTALL A CONTACT PLATE, E-CLIP, AND 2 CONTACT PLATE SPRINGS. OWNER NOTIFICATION BEGAN APRIL 19, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT HONDA AT 1-310-532-9811.
VEHICLE DESCRIPTION: MOTORCYCLES EQUIPPED WITH A NEWLY DESIGNED PULSE ROTOR. THE CRANKSHAFT PULSE ROTOR, A DEVICE USED FOR IGNITION TIMING, COULD FAIL AND CAUSE THE ENGINE TO STALL.
Consequence & remedy
Consequence: THIS SUDDEN LOSS OF ENGINE POWER COULD LEAD TO A CRASH.
Remedy: DEALERS WILL INSTALL A REDESIGNED PULSE ROTOR. OWNER NOTIFICATION BEGAN APRIL 19, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT HONDA AT 1-800-999-1009.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4
AQ12001 · Southern Honda Powersports
Opened May 14, 2012 · Closed May 13, 2013
Status: closed (inferred from source dates) · Unknown Or Other
NHTSA opened Audit Query (AQ) 12-001 to determine whether Southern Honda Powersports (Southern Honda) of Chattanooga, Tennessee, had complied with the requirements of the National Traffic and Motor Vehicle Safety Act, as amended, 49 U.S.C. Chapter 301 (Safety Act) and its implementing regulations. The Safety Act requires, among other things, that a motor vehicle or equipment manufacturer notify its dealers of defects related to motor vehicle safety and non-compliances with federal motor vehicle safety standards.In turn, a dealer may not sell and deliver a new vehicle subject to a recall unless the recall remedy has been performed.(see 49 U.S.C. 30120(i); 49 C.F.R. 573.11)NHTSA issued an information request to Southern Honda on May 14, 2012 to which they responded on July 6, 2012.NHTSA?s inquiry led it to believe that Southern Honda had failed to complete the requirements of five recalls that required inspections and/or repairs of motorcycles prior to their sale or delivery.NHTSA believes that 329 motorcycles affected by recalls had not been inspected and/or repaired prior to their sale and delivery between 2007 and 2012.The agency is unaware of any deaths or injuries involving these vehicles.NHTSA concluded that it had a potential civil penalty claim against Southern Honda for violations of the Safety Act.Southern Honda denied any violations of the Safety Act.In order to settle this matter, Southern Honda agreed to pay a civil penalty in the amount of $125,000, to be paid in five annual installments.This AQ is closed.
RQ04009 · Frame Crossmemeber Weld Failures
Opened Sep 21, 2004 · Closed Feb 2, 2005
Status: closed (inferred from source dates) · Structure:frame And Members
HONDA IS AMENDING THE SCOPE OF 03V-350 TO ADD 34,919 POTENTIALLY AFFECTED GL1800 GOLD WING MOTORCYCLES.THE INITIAL RECALL RANGE INCLUDED FRAMES MANUFACTURED WITH ONE OF A NUMBER OF WELDING PROCESSES.HONDA BELIEVED, ON THE BASIS OF DATA AVAILABLE AT THAT TIME, THAT ONLY THOSE GL'S BUILT WITH THAT ONE PROCESS WERE AT RISK OF FAILURE.WITH THE ORIGINAL RECALL (IN SEPTEMBER, 2003), HONDA INTRODUCED YET ANOTHER WELD PROCESS.SUBSEQUENTLY, HONDA BECAME AWARE OF INCIDENTS INVOLVING GL'S NOT INCLUDED IN THE ORIGINAL RECALL, BUILT USING ANOTHER EARLY WELDING PROCESS.THUS, HONDA HAS DECIDED TO RECALL ALL GL1800'S BUILT PRIOR TO SEPTEMBER 20, 2003 REGARDLESS OF WHAT WELD PROCESS WAS BEING USED AT THE TIME.THIS RECALL EXPANSION AFFECTS THE 2001, 2002, 2003 AND 2004 MODEL YEARS AND THE TOTAL NUMBER OF AFFECTED U.S. GL1800 MOTORCYCLES INCREASES FROM 8,196 TO 43,115.
PE03039 · Rear Suspension Collapse
Opened Aug 11, 2003 · Closed Oct 10, 2003
Status: closed (inferred from source dates) · Structure:frame And Members
THE SUBJECT MOTORCYCLES, INTRODUCED WITH THE 2001 MODEL YEAR, UTILIZE AN ALUMINUM FRAME INDIVIDUALLY WELDED BY HONDA EMPLOYEES IN THE COMPANY?S MARYSVILLE, OHIO ASSEMBLY PLANT.NHTSA/ODI OPENED THIS INVESTIGATION AFTER LEARNING THAT SOME 2002 MODEL YEAR GL1800?S WERE EXPERIENCING REAR SUSPENSION COLLAPSE WHEN THE LOWEST CROSSMEMBER WOULD COMPLETELY SEPARATE FROM THE FRAME.IT APPEARED THE CROSSMEMBER WAS SEPARATING DUE TO SUB-STANDARD WELDING OF THE CROSSMEMBER TO THE FRAME. ON SEPTEMBER 4, 2003 HONDA BRIEFED ODI STAFF AND ADVISED THAT THE SUBJECT WELD FAILURES RESULTED FROM A COMBINATION OF PRODUCTION LINE CHANGES THAT TOOK EFFECT ON MARCH 1, 2002.THESE CHANGES WERE:1) FEW, IF ANY, REINFORCING TIG WELDS APPLIED TO THE CROSSMEMBER MIG WELDS; 2) A RELATIVELY INEXPERIENCED WELDER BEGAN WELDING FRAMES AS OF THAT DATE; AND 3) A LESS ROBUST WELD QUALITY CONTROL INSPECTION WAS INTRODUCED.EFFECTIVE SEPTEMBER 11, 2002 HONDA ADDRESSED THESE ASSEMBLY LINE ISSUES.ON SEPTEMBER 16, 2003 HONDA ADVISED NHTSA/ODI THAT IT WAS CONDUCTING A SAFETY RECALL OF ALL MYR 2002/2003 GL1800?S BUILT FROM MARCH 1, 2002 THROUGH SEPTEMBER 10, 2002.THIS IS A WORLDWIDERECALL INVOLVING 9,521 MOTORCYCLES, OF WHICH 8,196 ARE IN THE UNITED STATES.FOR MORE INFORMATION CONCERNING BOTH HONDA?S SEPTEMBER 4TH BRIEFING AND THE RECALL, PLEASE REFER TO NHTSA?S OCTOBER 2, 2003 MEMO.BASED ON INFORMATION PROVIDED BY HONDA CONCERNING THE PRODUCTION LINE CHANGES; THE FIELD PERFORMANCE OF ALL 2001-2003 GL1800?S; AND NHTSA?S INDEPENDENT INFORMATION GATHERING ACTIVITIES; THE SCOPE OF HONDA?S RECALL APPEARS JUSTIFIED.ODI WILL CLOSELY MONITOR SUBJECT CROSSMEMBER WELD INTEGRITY FOR BIKES BUILT OUTSIDE THE RECALL SCOPE, AS WELL AS THE EFFECTIVENESS OF HONDA?S RECALL REMEDY FOR THOSE BIKES WITHIN IT, AND WILL TAKE ADDITIONAL ACTION IF WARRANTED BY FUTURE DEVELOPMENTS.
PE02077 · Motorcycle Coolant Spray Onto Rear Tire
Opened Oct 15, 2002 · Closed Mar 28, 2003
Status: closed (inferred from source dates) · Engine And Engine Cooling
SEE THE ATTACHED REPORT WITH ODI'SFINDINGS.
2001 Honda GL1800 Problems, Complaints & Recalls | Skip That Year
Illustration