IllustrationThe car lost all engine power on the interstate of I10. Leaving me without power, barely able to get to the side of the road. Warning only when lost engine power on the highway. Cannot be driven.
2016 GMC Yukon
Owner reports · Recalls · Investigations
More warning signs than most Yukon years
Owner complaints for the 2016 GMC Yukon are substantially higher than the model-year median of 103.
About this comparison →How this year compares
Owner complaints by model year
Compare all Yukon years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
150–25K
4225–50K
4550–75K
2575–100K
15100–150K
3150K+
145 reports with mileage · 122 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Exterior Lighting. Review the 104 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 53 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 52 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
4 crash reports0 fire reports4 injury reports
Engine complaints
34 reportsTicking sound coming from engine, possible damaged camshaft lobe due to lifter roller failure. It can cause sudden engine failure, significant power loss, and unexpected stalling while driving, increasing crash risks. The issue is linked to AFM (Active Fuel Management) system failures. The problem has been diagnosed by dealer s…
Read full complaint
Ticking sound coming from engine, possible damaged camshaft lobe due to lifter roller failure. It can cause sudden engine failure, significant power loss, and unexpected stalling while driving, increasing crash risks. The issue is linked to AFM (Active Fuel Management) system failures. The problem has been diagnosed by dealer service department. No warning lamp or message, problem first appeared 7 April 2026.
The contact owns a 2016 GMC Yukon. The contact stated that the vehicle was initially repaired under warranty for a bent push rod in cylinder #4; however, the failure recurred. The vehicle was repaired another time at the expense of the contact's son, who previously owned the vehicle; however, the failure persisted. The contact s…
Read full complaint
The contact owns a 2016 GMC Yukon. The contact stated that the vehicle was initially repaired under warranty for a bent push rod in cylinder #4; however, the failure recurred. The vehicle was repaired another time at the expense of the contact's son, who previously owned the vehicle; however, the failure persisted. The contact stated that while idling and while driving, the engine was misfiring and running rough. Additionally, there was a significant amount of smoke coming from the exhaust pipe. The check engine warning light was illuminated. The vehicle was taken back to the dealer, where it was diagnosed, and the dealer determined that the engine needed to be replaced. The vehicle was not repaired due to the cost. The manufacturer was contacted and informed that the repair would not be covered because the vehicle was out of warranty. The failure mileage was approximately 27,000.
Misfire then replaced plugs,coils and wires, then change fuel injector, and problem still there, then started truck and was tossing power and motor started ticking. Every shop told me this is the same common problem they're having with all 6.2L engine and they're all on recall by GM. I know 2016 are not in recall but I think th…
Read full complaint
Misfire then replaced plugs,coils and wires, then change fuel injector, and problem still there, then started truck and was tossing power and motor started ticking. Every shop told me this is the same common problem they're having with all 6.2L engine and they're all on recall by GM. I know 2016 are not in recall but I think they should be because this problem is in all 6.2L engine
On [XXX], while idling in my driveway the engine abruptly stopped with a loud clunk and refused to turn over when I attempted to restart it. The vehicle was towed to Bergstrom GMC in Appleton WI. Upon inspection it was determined that a connecting rod and crankshaft bearing had failed requiring replacement of the engine. The veh…
Read full complaint
On [XXX], while idling in my driveway the engine abruptly stopped with a loud clunk and refused to turn over when I attempted to restart it. The vehicle was towed to Bergstrom GMC in Appleton WI. Upon inspection it was determined that a connecting rod and crankshaft bearing had failed requiring replacement of the engine. The vehicle has a 6.2-litre V-8 engine with 106,000 miles on it. The vehicle is currently still at the dealership waiting for the engine replacement at an estimated cost of $18,000. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
A side detection module pin was corroded and was disrupting the electrical signals to major vehicle components, such as the dash (DIC). The DIC would lose communication with the rest of the vehicle while driving so no vehicle operation data was visible such as speed, alerts messages, etc. This likely also caused engine failure d…
Read full complaint
A side detection module pin was corroded and was disrupting the electrical signals to major vehicle components, such as the dash (DIC). The DIC would lose communication with the rest of the vehicle while driving so no vehicle operation data was visible such as speed, alerts messages, etc. This likely also caused engine failure due to the incorrect operation of the afm which is on the same electrical circuit. No warning messages were given. The bad side detection module was diagnosed and fixed at a dealer and shortly after engine issues were noticed.
Check engine light came on. Immediately went to reputable local repair shop. Shop advised push rod bent due to faulty engine. Advised to call GMC because not normal wear and tear. Called GMC expressed my frustration about this being preexisting issue w this engine. GMC corp told me I had to ship to GMC dealership at my own expe…
Read full complaint
Check engine light came on. Immediately went to reputable local repair shop. Shop advised push rod bent due to faulty engine. Advised to call GMC because not normal wear and tear. Called GMC expressed my frustration about this being preexisting issue w this engine. GMC corp told me I had to ship to GMC dealership at my own expense then they could help me. Local GMCs backed up 6-8 wks. Towed car 1.5 hrs away. Mechanic told me not to worry this happens all of the time, GMC will take care of it. Pointed out a row of new trucks with my incl new Escalade with same issue. I spoke to a sales rep about trading my car in for new but he said engine issue still not resolved. He advised me to lease Escalade for $900 because by the time my engine blew my lease would be up; if not GMC fix under warranty!! Mechanic said new engine but GMC will take care of it. I waited 3+ months for GMC to authorize repair. GMC said they did not get docs but mechanic sent me verification of conversation and repair order sent to GMC. Mechanic received an unrelated warranty from GMC that said my issue was not covered. Mechanic said docs sent made no sense bc he sent the right warranty and he was sorry and embarrassed by GMC behavior. I finally paid over 14K for new engine. Picked up my car and drive a block and car still knocking and engine light came back on. I had returned my rental and no way home. In tears dealership gave me my rental keys back still all at my expense. The mechanic calls me two days later to tell me my torque needs to be replaced. I am hysterical, 14k spent, and car still not fixed. GMC told me to pay additional funds for torque converter or pick up. Threatened to charge storage fees. When I discussed their liability GMC became very rude and antagonistic. They cut off my communication with their lead mechanic. Took care of back to local repair shop. He said this smells of a law suit so would not touch vehicle. I all communication 106 more files to share.
2 months ago our 16 gmc Yukon Denali 6.2 bent a push rod on cylinder 4 . So had to fix it when I took out DOD lifters put them on work bench and about 10 minutes out the DOD lifters flew apart and know having transmission issues it’s starting to shudder ! So I would liked the [XXX] thing recalled because engine still isn’t right…
Read full complaint
2 months ago our 16 gmc Yukon Denali 6.2 bent a push rod on cylinder 4 . So had to fix it when I took out DOD lifters put them on work bench and about 10 minutes out the DOD lifters flew apart and know having transmission issues it’s starting to shudder ! So I would liked the [XXX] thing recalled because engine still isn’t right either it only has 130000 miles. I’ll never buy a [XXX] gmc because of problems! I want the [XXX] thing fixed ASAP we paid to much money for it to be having problems!!!! Please send a recall letter to fix it ! [XXX] . 4/29/2025 6:53 p:m INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The contact owns a 2016 GMC Yukon. The contact stated that while driving at an undisclosed speed, the vehicle unexpectedly downshifted with the check engine warning light illuminated. The vehicle was taken to the dealer, where it was diagnosed that the transmission had failed and needed to be replaced. The vehicle was not repair…
Read full complaint
The contact owns a 2016 GMC Yukon. The contact stated that while driving at an undisclosed speed, the vehicle unexpectedly downshifted with the check engine warning light illuminated. The vehicle was taken to the dealer, where it was diagnosed that the transmission had failed and needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 250,000.
The contact owns a 2016 GMC Yukon. The contact stated that while driving at 65 MPH and attempting to accelerate, the vehicle briefly shuddered before returning to normal functionality. The check engine warning light was illuminated. The vehicle was taken to an independent mechanic, who diagnosed a failure with the torque convert…
Read full complaint
The contact owns a 2016 GMC Yukon. The contact stated that while driving at 65 MPH and attempting to accelerate, the vehicle briefly shuddered before returning to normal functionality. The check engine warning light was illuminated. The vehicle was taken to an independent mechanic, who diagnosed a failure with the torque converter. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was unknown.
Official recalls
519V761000 · Electronic Stability Control (esc); Service Brakes; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:wheel Speed Sensor/tone Ring
Oct 24, 2019
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence & remedy
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Additional source detail variants (3)
Service Brakes
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:wheel Speed Sensor/tone Ring
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Electronic Stability Control (esc)
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
19V645000 · Service Brakes, Hydraulic:power Assist:vacuum
Sep 6, 2019
General Motors LLC (GM) is recalling certain 2015-2017 Cadillac Escalade, 2014-2018 Chevrolet Silverado, GMC Sierra, 2015-2018 Chevrolet Suburban, Tahoe, GMC Yukon vehicles. The amount of vacuum created by the vacuum pump may decrease over time.
Consequence & remedy
Consequence: As the vacuum level drops, the brake assist decreases, increasing braking effort, extending the distance required to stop the vehicle, thereby increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began October 8, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438, Cadillac customer service at 1-800-458-8006 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192268490.
17V437000 · Air Bags:frontal; Air Bags:frontal:sensor/control MODULE-INACTIVE ; Seat Belts:pretensioner
Jul 10, 2017
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
16V651000 · Air Bags:frontal; Air Bags:frontal:sensor/control MODULE-INACTIVE ; Seat Belts:pretensioner
Sep 8, 2016
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
16V256000 · Suspension:front:control Arm
Apr 28, 2016
General Motors LLC (GM) is recalling certain model year 2016-2017 Chevrolet Silverado 1500 and 2016 Cadillac Escalade, Cadillac Escalade ESV, Chevrolet Suburban, Chevrolet Tahoe, GMC Sierra, GMC Yukon and GMC Yukon XL vehicles. The front upper control arms may have inadequate welds near the control arm bushing.
Consequence & remedy
Consequence: Inadequate welds may allow the control arm to separate from the bushing, compromising steering and increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the left and right front upper control arms and realign the vehicle, free of charge. The recall began on May 18, 2016. Until the repairs have been made, owners are advised not to drive their vehicles. Owners may contact Chevrolet customer service at 1-800-222-1020, Cadillac customer service at 1-800-458-8006, or GMC customer service at 1-800-462-8782. GM's number for this recall is 42190.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE18012 · Brake Vacuum Pump Failure
Opened Nov 20, 2018 · Closed Apr 10, 2022
Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Hydraulic; Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Additional source detail variants (3)
Service Brakes
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.