2024 GMC Sierra 2500

While driving my truck on the highway at 65 mph the truck bucked hard and immediately downshifted into 2nd gear. This caused me to rapidly decelerate to approximately 40 mph, I am lucky there was not another vehicle behind me when this happened since rapid unexpected deceleration without brake lights is very dangerous. I had to drive the truck in limp mode at 45mph and approximately 4500 rpms to the nearest exit. This event illuminated the trucks check engine light and displayed a brief service 4WD message followed by a permanent reduced acceleration message on the dash.

The contact owns a 2024 GMC Sierra 2500. The contact stated that while driving at an undisclosed speed and approaching a stop, the contact simultaneously depressed the brake pedal and accelerator pedal, causing the vehicle to move forward and to stop simultaneously. The contact stated that the pedals were significantly close to each other. The contact’s foot was sliding off the pedals. The vehicle was taken to the local dealer, and the contact requested for an adjustment of the pedals. The vehicle was not diagnosed or repaired. The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 10.

First date was 04/23/2024 my truck went into limp mode with an alert reading engine and transmission control module problem. Brought it in and they reset the sensors. Shortly after the alert warning goes off again and I turn the engine off and start it back up. It cleared the alert, I brought it back in on 06/15/2024. They reset sensor and fixed a recall on tailgate. I picked up truck, drove it for 2 months and TCM warning came up and threw truck into limp mode while pulling a 2 horse trailer. It turned a 3 hr drive into a 6 hr drive. I brought back to dealer on 8/19/2024 they had it for 4 days and they notified me that this is an on going problem. It is a transmission solenoid valve stuck open and they ordered the part and told me it could be months before the part gets here due to the ongoing backorder from all the other trucks that have the same problem. I use this truck for work and leisure to pull my boat and 2 horse trailer and now I have a vehicle payment to make and no vehicle to use. I cannot use it to work or anything else because it is at the dealer for an unspecified amount of time. I have read online that this is a major problem with this truck and GMC as well as the dealerships know about this problem and they still sold it to me. There are so many complaints online about this GMC 2500 AT4 truck problem that GMC should stop selling this truck.

The contact owns a 2024 GMC Sierra 2500. The contact stated while stopped at an intersection, the vehicle moved forward while the brake pedal was fully depressed. The contact also stated on a level surface, the vehicle accelerated about 4 MPH without the accelerator pedal being depressed. The failure occurred on several occasions. The vehicle was taken to the dealer where the failure was duplicated; however, the dealer stated that the vehicle operated as designed. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 100.

The Column Shifter that is installed on all 2024 GMC Sierra 2500HDs and 3500HDs poses a potential safety risk to its passengers and other drivers on the road. When the column shifter of the vehicle is in the standard drive position the shifter covers part of the screen and the direct path to the radio volume control dial and infotainment home button. It has been found and replicated that attempting to interact with the infotainment screen UI and the home button/volume control dial the driver may easily accidentally bump the shifter into the neutral position. Bumping this 8000lbs+ vehicle into neutral unintentionally can be extremely dangerous to its passengers and fellow motorists especially when hauling a heavy trailer or load like heavy-duty pickup trucks are designed to do. Bumping the truck into neutral can allow the truck to lose its acceleration capabilities and degrade braking capabilities as the engine would be disconnected from the drive wheels, limiting engine braking and exhaust braking. This kind of braking is commonly used to help stop the truck with heavy trailers and loads. This problem has been commonly referred to in multiple Facebook groups relating to the 2024 GMC Heavy Duty Truck. I personally have not had it inspected by any third party as there is not much they can do to remedy the issue. I personally recommend that General Motors redesign the column shifter in these trucks shortening it to come no further than the diameter of the steering wheel eliminating any interference with the infotainment system and the home button/volume dial. GM shall replace this updated shifter free of charge in all trucks just recently built. For GM's sake, it is important that this issue is remedied ASAP as the truck just began production and there is a limited amount on the road. This is available for inspection upon request.