IllustrationGM refuses to repair the defective finish on my truck, their claim is that it only applies to trucks covered under the 3 year -36k warranty. This is a manufacturing defect that they admit to in the attached TSB. There should be a recall mandated for this. We spent a ton of hard earned money on these trucks.
2014 GMC Sierra 2500
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2014 GMC Sierra 2500 do not stand out strongly from the model-year median of 46.
About this comparison →How this year compares
Owner complaints by model year
Compare all Sierra 2500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
70–25K
625–50K
350–75K
475–100K
3100–150K
0150K+
23 reports with mileage · 7 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 6 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Steering. Review the 6 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 4 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
2 crash reports1 fire reports0 injury reports
Unknown Or Other complaints
7 reportsI OWN A 2014 GMC SIERRA 2500HD. IT IS IN VERY GOOD CONDITION AND WELL MAINTAINED WITH LESS THAN 140,000 ON IT. ONE DAY AFTER WORK I GOT INTO MY TRUCK AND AS SOON AS I STARTED IT I HEARD MY DASH CRACK. IT CRACKED JUST TO THE RIGHT OF THE INSTRUMENT PANEL BY THE DASH VENT AND WINDSHIELD. AND HAS BEEN GROWING EVER SINCE. IF THE DAS…
Read full complaint
I OWN A 2014 GMC SIERRA 2500HD. IT IS IN VERY GOOD CONDITION AND WELL MAINTAINED WITH LESS THAN 140,000 ON IT. ONE DAY AFTER WORK I GOT INTO MY TRUCK AND AS SOON AS I STARTED IT I HEARD MY DASH CRACK. IT CRACKED JUST TO THE RIGHT OF THE INSTRUMENT PANEL BY THE DASH VENT AND WINDSHIELD. AND HAS BEEN GROWING EVER SINCE. IF THE DASH IS THIS BRITTLE IN A TRUCK THAT IS ONLY 6 YEARS OLD AND BEEN VERY WELL TAKEN CARE OF IT IS A SAFETY ISSUE. IF I WERE TO GET INTO A CRASH AND MY AIRBAGS WERE TO DEPLOY, SHARDS OF HARD BRITTLE PLASTIC WOULD BE SENT THROUGH THE CAB POSSIBLY CAUSING MORE INJURIES.
DASH IS FULLY CRACKED AT THE CORNER OF THE PASSENGER AIRBAG. IN ADDITION, A CRACK FORMED ABOVE THE INSTRUMENT PANEL AND CONTINUED TO SPREAD.
THE DASHBOARD IS CRACKED ON PASSENGER SIDE NEXT TO THE AIRBAG.
I PURCHASED THIS TRUCK NOVEMBER 26 2016, WITHIN A MONTH I WAS SITIING IN MY DRIVEWAY I TURNED THE TRUCK ON WHEN I WENT OUT TO GO TO WORK IN THE MORNING I GOT A BUNCH OF FLASHING LIGHTS SERVICE STABILITRAK, SERVICE 4WHEEL DRIVE, SERVICE TRACTION CONTROL, MADE MULTIPLE ATTEMPTS TO CONTACT FIVE STAR AUTO IN BIDDEFORD, BROUGHT THE T…
Read full complaint
I PURCHASED THIS TRUCK NOVEMBER 26 2016, WITHIN A MONTH I WAS SITIING IN MY DRIVEWAY I TURNED THE TRUCK ON WHEN I WENT OUT TO GO TO WORK IN THE MORNING I GOT A BUNCH OF FLASHING LIGHTS SERVICE STABILITRAK, SERVICE 4WHEEL DRIVE, SERVICE TRACTION CONTROL, MADE MULTIPLE ATTEMPTS TO CONTACT FIVE STAR AUTO IN BIDDEFORD, BROUGHT THE TRUCK IN THEY REFUSED TO FIX ISSUES, ASKED FOR A TRADE NOTHING ON THE LOT WAS WORTH PURCHASING WITHOUT PUTTING ME OUT MORE THAN I ALREADY OWED,CHRISTMAS MORNING THE TRUCK WAS TOWED TO WEIRS IN ARUNDEL THEY PULLED THE TRUCK APART AND FOUND A BUNCH OF WIRES WERE CORRODED AND THE FRAME OF THE TRUCK WAS CAKED WITH ROCKS MUD AND SAND WHICH HAD CAUSED THE CORROSION, THEY FIXED THE ISSUE. WITHIN A COUPLE MONTHS THE SAME ISSUE CAME BACK UP AND ONCE AGAIN THE TRUCK WAS IN THE SHOP GETTING WORKED ON. THE PROBLEM IS NOT FIXED AFTER SPENDING MONEY TO FIX A PROBLEM I HAD LESS THAN 30 DAYS FROM BUYING THIS VEHICLE(DRIVING COMPLETELY NORMAL WILL CAUSE THESE LIGHTS TO FLASH AT RANDOM TIMES) , ALL THE LIGHTS DO STILL COME ON RANDOMLY AND TODAY WHILE AT THE DAYTON COUNTRY STORE MY TRANSMISSION IN MY TRUCK WENT, I AM WAITING TO GET MY TRUCK TOWED FROM THE STORE TO A SHOP! FOR A VEHICLE THAT THE CARFAX CAME BACK CLEAN AND THE DEALERSHIP MADE NO ATTEMPT IN HELPING ME FIX OR PAY FOR ANY ISSUES I HAVE HAD. IM NOW STRUGGLING WITH A VEHICLE THAT I WAS LIED TO ABOUT THE CONDITION IT WAS IN AFTER PAYING $32,000 FOR A TRUCK. I HAVE KEPT ALL DOCUMENTATION AND HAVE IMAGES THAT WERE SENT TO ME FROM WEIRS
THERE IS A SMALL CRACK IN THE DASHBOARD NEXT TO THE AIRBAG. GMC WILL NOT REPAIR IT AT THEIR COST.
MY DASH CRACKED AND I SEE THIS IS A REAL PROBLEM. THEY SAY $900 TO FIX AND MY TRUCK HAS JUST 40K ON IT AND LESS THEN 2 YEARS OLD.
Official recalls
221V054000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally GM is recalling certain 2011-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, Yukon XL and 2011-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Additionally, GM is recalling certain 2010-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL and 2010-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 25, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed to 40 VIN owners on May 11, 2021. A second owner notification letter was mailed to all other owners on January 24, 2022. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328800.
18V267000 · Equipment
Apr 26, 2018
General Motors LLC (GM) is recalling certain 2009-2014 Chevrolet Silverado HD and GMC Sierra HD, 2009 GMC Topkick 5000, 6000, 7000 and 8000 Series and Isuzu F Series, and 2009-2018 Chevrolet Express, and GMC Savana vehicles, equipped with certain Plastic-Handle Fire Extinguishers or Push Button 'Pindicator' Fire Extinguishers. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.
Remedy: GM will notify owners, instructing them to contact Kidde to get a replacement fire extinguisher, free of charge. The recall began June 11, 2018. Owners may contact Chevrolet customer service at 1-800-222-1020, GMC customer service at 1-800-462-8782, and Isuzu customer service at 1-866-441-9638. GM's number for this recall is 18146.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.