2025 GMC Sierra 1500

Either while stopping while driving or parking (forward or reverse) the engine RPMs go up thus wanting to move the vehicle in that direction causing the breaks needing to be applied harder. When you shift into neutral the RPMs go way up (3000). This has happened on this vehicle 3-4 times of which I have video of the latest occurrence. When put into R or D the RPMs are still over 1000. This also happened on the courtesy vehicle same make and model) I was given but on this one the RPMs went up to 5000 of which I also have a video. The dealership has not been able to duplicate the issue as of yet. My fear is that the vehicle will hit someone or something if the break isn't pressed to the floor. It happens very randomly. The dealer currently has my vehicle trying to figure it out. They say GM says there's nothing they can do. No warning lights or messages appeared.

Rough idle started at 11,400 miles. Took to GMC dealer near me and had thrust bearing clearance measured. Measured .0054"(within spec). They released truck back to me. 19,400 mile oil change found large metal(non magnetic) slivers in the filter media. I cut filters to check for issues due to known issues with this engine(metal). I called gmc corporate, i was told to not drive the truck. I paid out of pocket for the tow 142 miles away. Dealer told me they checked thrust bearing and came in at .0055", no noises, and no check engine light. Idle is very rough on start up. GM corporate stated a service advisor will call. Never got a call. I have sent and displayed the evidence and offered to show oil filter contents to both dealer and corporaten both have not done anything about this safety issue. This is a SEVERE safety issue. Engine is highly likely to lock up and cause serious injury to both me, my family, and others on the road. Dealer has released truck back to me and my family with clean bill stating they didnt find anything wrong. They refused to see my documentation of metal slivers or the 3 rimg binder full of maintenance records. As of now i will be escalating this to higher up in GMC corporate. SEVERE safety risk for my family and everyone on the road. GMC dealers refusing to diagnose.

In normal operation on Tuesday May 26,2026, the engine experienced catastrophic failure. The engine is the GM L87 6.2 Liter. This was on a highway in the country and I was able to maneuver the truck off the road before an accident occurred. It did leave me stranded and I was required to get it towed on a roll off (It was not drivable) to the dealer where I purchased it. The dealer [XXX] ) inspected my truck and has informed me that the issues with my 2025 Sierra match the issues for the recall GM had for the model years 2021-2025. It will require a new engine, radiator, among many other parts. There weren't any previous warnings. A check engine light only came on once the engine was engine came apart. An oil change on the vehicle by GM was done a month ago. The truck is a 2025 and has approximately 6,600 miles is all. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Upon purchase of my 2025 GMC Sierra, it did not come with a physical manual. I asked the dealer about this and they said they did away with them, only providing the digital version. I contacted GMC recently as I saw the a recall dor 2026 models with this exact issue, but they did not seem to care and it was for 2026 models only. I find this to be a loophole GMC is following, and would just like a manual so I can log maintenance like a normal person without a phone or sitting in my vehicle. Thank you

My GMC sierra AT4 with the 3.0L Duramax Diesel, has 1,500 miles on it, when the engine failed. I was traveling from [XXX] to [XXX] , towing a trailer, when the check engine light came, and the truck entered reduced power mode. It immediately slowed the truck without warning - which made for a very dangerous situation for all of the vehicles behind me and for my vehicle. After getting the vehicle and trailer to a dealer, disconnecting the trailer, and then getting the truck in the shop, the dealer defined the OBDII code as being P06DD - Engine oil pressure control solenoid valve stuck off. U0146 - Lost communication with central gateway module, and U1605 - Lost communication with side obstacle detection control module - right on private CAN Bus. The dealer indicated that the P06DD code meant that the thrust bearing on the crankshaft failed and the engine would need to be replaced. The ending only has 1500 miles on it. It turns out that there are MANY GM 3.0L diesel engines that have failed for this issue and that GM issued a Technical Service bulletin in 2025 for this issue - TSB 25-NA-307. I work in the medical device industry and when there is a safety issue with your products - you initiate a RECALL. To date there has been no recall simply the TSB. What is the NHTSA going to do about ensuring that GM, and other manufacturers, are making engines safe? These engines can literally explode - sending metal shards through the engine into the passenger compartment. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

Truck does not automatically shift into park when the door is opened. Getting out of my truck, I forgot to shift into park and opened the door, and the truck moved forward with automatically shifting into park, or applying the parking brake. I have a 2015 Jeep Grand Cherokee that did the same thing. There was a safety recall set forth by the NHTSA to have the car go into park when the door opened to prevent someone for being run over by the vehicle. My 2025 GMC Sierra is experiencing the same issue. I was not harmed, but can definitely see someone getting hurt.