IllustrationDashboard lit up with engine light and stated that there's no compulsion
2021 GMC Sierra 1500
Owner reports · Recalls · Investigations
More warning signs than most Sierra 1500 years
Owner complaints for the 2021 GMC Sierra 1500 are substantially higher than the model-year median of 181.
About this comparison →How this year compares
Owner complaints by model year
Compare all Sierra 1500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 117 of 563 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine. Review the 299 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 134 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 73 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
5 crash reports6 fire reports2 injury reports
Power Train complaints
134 reportsThe contact owns a 2021 GMC Sierra 1500. The contact stated that while driving at an undisclosed speed, the brake pedal was depressed, but the vehicle continued to move forward. There was no warning light illuminated. The vehicle was taken to the dealer and was diagnosed with transmission failure. The contact stated that the val…
Read full complaint
The contact owns a 2021 GMC Sierra 1500. The contact stated that while driving at an undisclosed speed, the brake pedal was depressed, but the vehicle continued to move forward. There was no warning light illuminated. The vehicle was taken to the dealer and was diagnosed with transmission failure. The contact stated that the valve body and torque converter needed to be replaced. The dealer informed the contact that the transmission might need to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 65,561. The VIN was unavailable.
While driving my vehicle, the engine and transmission lost power and the check engine light came on. The vehicle went into limp mode and engine propulsion was limited. Had I been traveling at a faster speed, this would have been very unsafe. After coming to a stop, placing the transmission in reverse did not move the vehicle and…
Read full complaint
While driving my vehicle, the engine and transmission lost power and the check engine light came on. The vehicle went into limp mode and engine propulsion was limited. Had I been traveling at a faster speed, this would have been very unsafe. After coming to a stop, placing the transmission in reverse did not move the vehicle and there was a grinding noise. I was able to savely move forward in limp mode, but the shifting was harsh. I was able to find an empty parking lot to safely park. The truck was towed to Jim Winter dealership in Jackson MI for inspection.
So I made an appointment to have my truck recalled and the Wednesday before I took it, and it cranked no start and I called the dealership. Ask if they had any other those like this and they said that it could be the fuel injector module and so I got it to a mechanic shop to read the codes and it gave me a code p062b and I asked…
Read full complaint
So I made an appointment to have my truck recalled and the Wednesday before I took it, and it cranked no start and I called the dealership. Ask if they had any other those like this and they said that it could be the fuel injector module and so I got it to a mechanic shop to read the codes and it gave me a code p062b and I asked the dealership to look into it and they never figured out what we were not wrong. I just testing the battery. Well, then I got it back after the recall was done and new transmission valve body put in and about 30 miles down the road it started to shake violently and had a flashing engine light so I got it home called the dealership the next morning because they were closed set up another appointment got it to the dealership dealership said it had a couple misfires but since it wasn’t over 100 they weren’t concerned even though I’m pretty sure it is related to the fuel model going out because it has been cranking rapidly whenever I try to start it, but they won’t do anything to figure out what’s wrong?
When pressing on the gas, especially when moderately accelerating, the truck experiences severe shaking, which interferes with acceleration, as well as causing the truck to "jump" when the transmission gear "catches", even while driving. When the truck is at a full stop and the engine is auto off, when it restarts, it does so fr…
Read full complaint
When pressing on the gas, especially when moderately accelerating, the truck experiences severe shaking, which interferes with acceleration, as well as causing the truck to "jump" when the transmission gear "catches", even while driving. When the truck is at a full stop and the engine is auto off, when it restarts, it does so frequently when it reengages that it causes a physical "jump" in the vehicle, causing the driver's foot to come off the brake pedal. This has been most noticeable since my vehicle hit about 70k miles. I currently have 84k miles. I engaged the dealer and was told the transmission is out of warranty. I see that other GMC Sierra models suffer similar problems and recalls have been issued to GMC that they must repair those vehicles. Despite that, my vehicle is not included in any current recall program.
While coasting down or under very light acceleration between 12-20 mph the vehicle has a shudder like driving over a highway rumble strip. While cruising on the highway at 65+ mph, the vehicle has a light shudder or vibration. Vehicle has been checked numerous times for wheel and tire inconsistencies. Brake pads and rotors hav…
Read full complaint
While coasting down or under very light acceleration between 12-20 mph the vehicle has a shudder like driving over a highway rumble strip. While cruising on the highway at 65+ mph, the vehicle has a light shudder or vibration. Vehicle has been checked numerous times for wheel and tire inconsistencies. Brake pads and rotors have also been replaced with no change in issue. Headlights daytime running light changes color from bright white to purple during warm weather. The vehicle has been to 3 different GM dealerships and they acknowledge the issues but do not provide a resolve.
power steering locked up while driving. has been inspected and repaired by manufacturer. recall.
power steering locked up while driving. multiple dash lights turned on, on its own after the issue, 4wd, emergency brake, abs, and other ones im not sure what they are. took it to the dealership for a recall and told them the issue that happened.
The truck randomly will not detect that it was shifted into park. Shifting between gears and back to park does not automatically fix the the issue and has taken up to 10 mins to turn the truck off. The adaptive cruise controls stopped working and can still use regular cruise control. Just not adaptive. It appears greyed out. T…
Read full complaint
The truck randomly will not detect that it was shifted into park. Shifting between gears and back to park does not automatically fix the the issue and has taken up to 10 mins to turn the truck off. The adaptive cruise controls stopped working and can still use regular cruise control. Just not adaptive. It appears greyed out. The truck has thrown the error code: P1098, Engine Coolant Control Valve Position Sensor Minimum Stop Performance. The truck would go into limp mode until the error was cleared. This error has appeared 4 times over the past five months. The most recent date of it happening was today. 06/30/2026
The truck has a studder that comes from the transmission when at highway speeds. the studder can be felt at random intervals (seconds) from all passengers. The studder is also present on starting up a slope or accelerating from a stop at a slow pace. when accelerating slowly the jerk is more prominent. We have taken it to th…
Read full complaint
The truck has a studder that comes from the transmission when at highway speeds. the studder can be felt at random intervals (seconds) from all passengers. The studder is also present on starting up a slope or accelerating from a stop at a slow pace. when accelerating slowly the jerk is more prominent. We have taken it to the GM Dealership, they confirmed the issue was present. The dealership said the GM guidence was to 1st try a re-program and then replace the torque converter. The program flash was unsuccessful, then we paid $4000 to change the torque converter. The Tech stated that this was the GM suggested fix, but noted that we are changing the fluid also which could mask the issue if it is the valve body causing an issue. The replacement torque converter and fluid did somewhat reduce the issue for a short period of about 2 months before it has returned as it did before. The next option from the dealership is in excess of $8,000 for a remanufactured transmission which is outside our reasonable spend, when we dont expect the remanufactured transmission will have any better valve body components. The recent recall did not cover my gas 6.2L sierra 1500, although it clearly is insufficient stating that it just a warning that there is a safety risk present. The valve body of the transmission appears to be an issue across all models and the recall addresses that it is present. We continue to drive this as the primary family vehicle with the hesitation and jerking present as GM dealer offered no support other than $8,000 remanufactured transmission on top of the $4000 we already spent. I believe the recall was insufficent in covering the Gas models with the exact same transmission and known issue. I also believe the offered solution continues to put those driving at risk.
Official recalls
726V083000 · Power Train:automatic Transmission:control Module:software; Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
Feb 12, 2026
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence & remedy
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
Additional source detail variants (2)
Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
Power Train:automatic Transmission:control Module:software
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
25V274000 · Engine And Engine Cooling:engine:hard Parts Internal/mechanical
Apr 24, 2025
General Motors LLC (GM) is recalling certain 2021-2024 Cadillac Escalade and Escalade ESV, Chevrolet Silverado 1500, Suburban, and Tahoe, GMC Sierra 1500, Yukon, and Yukon XL vehicles equipped with a 6.2L V8 gas engine. The connecting rod and/or crankshaft engine components may have manufacturing defects that can lead to engine damage and engine failure.
Consequence & remedy
Consequence: Engine failure increases the risk of a crash.
Remedy: Dealers will inspect the engine, and as necessary, repair or replace the engine. For vehicles that pass inspection, dealers will add higher viscosity oil, install 6 oil fill cap, replace the oil filter, and update the owner's manual. Repairs will be performed free of charge. Owner notification letters were mailed June 18, 2025. Owners may contact Cadillac customer service at 1-800-333-4223, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is N252494000.
24V797000 · Power Train:automatic Transmission:control Module:software; Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
Oct 24, 2024
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence & remedy
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
Additional source detail variants (2)
Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
Power Train:automatic Transmission:control Module:software
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
21V985000 · Tires:temporary/emergency Spare Tire
Dec 16, 2021
General Motors (GM) is recalling certain 2019-2021 GMC Sierra 1500 and Silverado 1500 vehicles equipped with certain accessory road tires and a 17" spare tire. The 17" spare tire provided with the vehicle is not compatible for use with the accessory wheels, which can cause the anti-lock brake system (ABS) to not function properly under certain conditions.
Consequence & remedy
Consequence: An ABS system that does not function properly can increase the risk of a crash.
Remedy: Dealers will provide a new 17" spare tire and wheel assembly that is compatible with the accessory wheels, free of charge. Dealers will also apply a new spare tire information label, and provide owners with an owner's manual insert clarifying which spare tire to use with the accessory road tires and with the 17" original tires. Owner notification letters were mailed February 7, 2022. Owners may contact GM customer service at 1-800-462-8782 or GMC customer service at 1-800-462-8782. GM's number for this recall is N212346510.
20V811000 · Seat Belts; Seat Belts:critical Fasteners
Dec 23, 2020
General Motors, LLC (GM) is recalling certain 2020 Chevrolet Bolt EV and 2021 GMC Canyon and Sierra 1500, 2500 and 3500, Yukon, Yukon XL, Cadillac Escalade and Escalade ESV and Chevrolet Blazer, Camaro, Colorado, Equinox, Silverado 1500, 2500 and 3500, Suburban and Tahoe vehicles. Incorrect bolts may have been used at one or more fastening locations to secure the seat belts to the vehicle. If an incorrect bolt was used, the seat belt may not be properly attached to the vehicle.
Consequence & remedy
Consequence: If a seat belt assembly is not properly attached to the vehicle, the seat belt may not properly restrain an occupant in the event of a crash, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the suspect bolts, free of charge. The recall began January 29, 2021. Owners may contact GMC customer service at 1-800-462-8785, Cadillac customer service at 1-800-458-8006, or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202322230.
Additional source detail variants (2)
Seat Belts:critical Fasteners
General Motors, LLC (GM) is recalling certain 2020 Chevrolet Bolt EV and 2021 GMC Canyon and Sierra 1500, 2500 and 3500, Yukon, Yukon XL, Cadillac Escalade and Escalade ESV and Chevrolet Blazer, Camaro, Colorado, Equinox, Silverado 1500, 2500 and 3500, Suburban and Tahoe vehicles. Incorrect bolts may have been used at one or more fastening locations to secure the seat belts to the vehicle. If an incorrect bolt was used, the seat belt may not be properly attached to the vehicle.
Consequence: If a seat belt assembly is not properly attached to the vehicle, the seat belt may not properly restrain an occupant in the event of a crash, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the suspect bolts, free of charge. The recall began January 29, 2021. Owners may contact GMC customer service at 1-800-462-8785, Cadillac customer service at 1-800-458-8006, or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202322230.
Seat Belts
General Motors, LLC (GM) is recalling certain 2020 Chevrolet Bolt EV and 2021 GMC Canyon and Sierra 1500, 2500 and 3500, Yukon, Yukon XL, Cadillac Escalade and Escalade ESV and Chevrolet Blazer, Camaro, Colorado, Equinox, Silverado 1500, 2500 and 3500, Suburban and Tahoe vehicles. Incorrect bolts may have been used at one or more fastening locations to secure the seat belts to the vehicle. If an incorrect bolt was used, the seat belt may not be properly attached to the vehicle.
Consequence: If a seat belt assembly is not properly attached to the vehicle, the seat belt may not properly restrain an occupant in the event of a crash, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the suspect bolts, free of charge. The recall began January 29, 2021. Owners may contact GMC customer service at 1-800-462-8785, Cadillac customer service at 1-800-458-8006, or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202322230.
20V792000 · Seat Belts; Seat Belts:critical Fasteners
Dec 17, 2020
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence & remedy
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
Additional source detail variants (2)
Seat Belts:critical Fasteners
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
Seat Belts
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
20V684000 · Tires
Nov 5, 2020
General Motors LLC (GM) is recalling certain 2020 Buick Enclave, Cadillac XT5, GMC Acadia and Chevrolet Traverse vehicles and 2020-2021 Chevrolet Silverado 1500, GMC Sierra 1500 vehicles. The vehicles may have been manufactured with Continental tires that were overcured.
Consequence & remedy
Consequence: Overcured tires may experience a carcass break in the sidewall resulting in a sudden air loss or could develop a belt edge separation which could lead to partial or full tread/belt loss. Either condition increases the risk of a crash.
Remedy: GM will notify owners, and dealers will inspect vehicles and replace tires that have DOT number and production mold number combinations identified by Continental, free of charge. The recall began December 17, 2020. Owners may contact GMC customer service at 1-888-988-7267, Buick customer service at 1-866-608-8080, Chevrolet customer service at 1-800-222-1020 or Cadillac customer service at 1-800-458-8006. GM's number for this recall is N202319030.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
5EA26005 · Loss Of Motive Power Due To Engine Failure Post Recall Remedy
Opened Aug 20, 2026 · No close date supplied
Status: open (inferred from source dates) · Engine
On January 16, 2026, the Office of Defects Investigation (ODI) opened Recall Query RQ26001. This investigation was opened to assess the remedy effectiveness of Recall 25V-274. ODI has received complaints alleging engine failure in vehicles after the recall remedy had been completed, whether that remedy involved an oil viscosity change or a complete engine replacement. General Motors (GM) issued Recall 25V-274 to address concerns of engine failure in the L87 engines produced between March 1, 2021 and May 31, 2024. GM cited the root cause as a supplier manufacturing and quality issue. GM’s recall remedy for Recall 25V-274 consisted of two different repairs, either an oil viscosity change or an engine replacement, based on the results of the remedy inspection procedure. ODI continues to receive reports of engine failures after the completion of the recall remedy. To date, ODI has received 499 complaints alleging post-remedy engine failure in vehicles subject to Recall 25V-274, 473 of which involved an oil viscosity change and 26 a complete engine replacement. Additionally, ODI has received 191 reports of L87 engine failures in engines produced after the production period cited in Recall 25V-274. GM reported receiving 6,953 complaints of post-remedy engine failure. ODI is opening this Engineering Analysisto continue investigating complaints of post-remedy engine failure. ODI is expanding the scope of this Investigation to include engines produced after the production period cited in the recall. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
RQ26001 · Loss Of Motive Power Due To Engine Failure Post Recall Remedy
Opened Jan 16, 2026 · Closed Aug 20, 2026
Status: closed (inferred from source dates) · Engine
On January 16, 2026, the Office of Defects Investigation (ODI) opened Recall Query RQ26001. This investigation was opened to assess the remedy effectiveness of Recall 25V-274. ODI has received complaints alleging engine failure in vehicles after the recall remedy had been completed, whether that remedy involved an oil viscosity change or a complete engine replacement. General Motors (GM) issued Recall 25V-274 to address concerns of engine failure in the L87 engines produced between March 1, 2021 and May 31, 2024. GM cited the root cause as a supplier manufacturing and quality issue. GM’s recall remedy for Recall 25V-274 consisted of two different repairs, either an oil viscosity change or an engine replacement, based on the results of the remedy inspection procedure. ODI continues to receive reports of engine failures after the completion of the recall remedy. To date, ODI has received 499 complaints alleging post-remedy engine failure in vehicles subject to Recall 25V-274, 473 of which involved an oil viscosity change and 26 a complete engine replacement. GM reported receiving 6,953 complaints of post-remedy engine failure. ODI will close this RQ and continue to investigate complaints of post-remedy engine failure for Recall 25V-274 as part of an Engineering Analysis (EA26005). To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
EA25007 · Loss Of Motive Power Due To Engine Failure
Opened Oct 23, 2025 · No close date supplied
Status: open (inferred from source dates) · Engine; Engine And Engine Cooling:engine:hard Parts Internal/mechanical
The Office of Defects Investigation (ODI) has received 1,157 reports of engine bearing failure failures in the L87 6.2L engine produced by General Motors (GM). Of the 1,157 reports received, 173 are outside of the scope of recall 25V-274. These engines are installed in Model Years (MY) 2019–2024 Chevrolet Silverado 1500 and GMC Sierra 1500, and 2021-2024MY Chevrolet Suburban and Tahoe, GMC Yukon/Yukon XL, and Cadillac Escalade/Escalade ESV vehicles. The subject engine failures were investigated as part of a Preliminary Evaluation (PE25001). GM determined that these engine failures were due to multiple supplier manufacturing and quality issues. GM issued recall 25V-274 to address the supplier manufacturing and quality issues produced between March 1, 2021, and May 31, 2024. Based on the issuance of recall 25V-274, NHTSA has closed PE25001. ODI continues to receive a significant number of reports of engine failure in vehicles outside the scope of 25V-274. This presents a potential safety risk that warrants further investigation. ODI is opening this Engineering Analysis (EA) to further evaluate the scope and severity of the potential problem and to fully assess the potential safety-related issues of vehicles built outside the recall scope. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:hard Parts Internal/mechanical
The Office of Defects Investigation (ODI) has received 1,157 reports of engine bearing failure failures in the L87 6.2L engine produced by General Motors (GM). Of the 1,157 reports received, 173 are outside of the scope of recall 25V-274. These engines are installed in Model Years (MY) 2019–2024 Chevrolet Silverado 1500 and GMC Sierra 1500, and 2021-2024MY Chevrolet Suburban and Tahoe, GMC Yukon/Yukon XL, and Cadillac Escalade/Escalade ESV vehicles. The subject engine failures were investigated as part of a Preliminary Evaluation (PE25001). GM determined that these engine failures were due to multiple supplier manufacturing and quality issues. GM issued recall 25V-274 to address the supplier manufacturing and quality issues produced between March 1, 2021, and May 31, 2024. Based on the issuance of recall 25V-274, NHTSA has closed PE25001. ODI continues to receive a significant number of reports of engine failure in vehicles outside the scope of 25V-274. This presents a potential safety risk that warrants further investigation. ODI is opening this Engineering Analysis (EA) to further evaluate the scope and severity of the potential problem and to fully assess the potential safety-related issues of vehicles built outside the recall scope. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
The Office of Defects Investigation (ODI) has received 1,157 reports of engine bearing failure failures in the L87 6.2L engine produced by General Motors (GM). Of the 1,157 reports received, 173 are outside of the scope of recall 25V-274. These engines are installed in Model Years (MY) 2019–2024 Chevrolet Silverado 1500 and GMC Sierra 1500, and 2021-2024MY Chevrolet Suburban and Tahoe, GMC Yukon/Yukon XL, and Cadillac Escalade/Escalade ESV vehicles. The subject engine failures were investigated as part of a Preliminary Evaluation (PE25001). GM determined that these engine failures were due to multiple supplier manufacturing and quality issues. GM issued recall 25V-274 to address the supplier manufacturing and quality issues produced between March 1, 2021, and May 31, 2024. Based on the issuance of recall 25V-274, NHTSA has closed PE25001. ODI continues to receive a significant number of reports of engine failure in vehicles outside the scope of 25V-274. This presents a potential safety risk that warrants further investigation. ODI is opening this Engineering Analysis (EA) to further evaluate the scope and severity of the potential problem and to fully assess the potential safety-related issues of vehicles built outside the recall scope. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
PE25001 · Loss Of Motive Power Due To Engine Failure
Opened Jan 16, 2025 · Closed Oct 23, 2025
Status: closed (inferred from source dates) · Engine; Engine And Engine Cooling:engine:hard Parts Internal/mechanical
On January 16, 2025, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE25001 after receiving complaints and field reports concerning engine failures in MY2019-2024 GM’s full-size truck and SUV T1XX platform equipped with the L87 6.2L V8 engine. These complainants alleged engine bearing failures resulting in knocking and growling noises from the engine’s bottom end and in some cases more severe consequences such as broken connecting rods leading to engine damage, or engine failure. If the engine fails during vehicle operation, the vehicle will lose propulsion, increasing the risk of a crash. On April 24, 2025, GM issued recall 25V-274 to address the concern with L87 engines produced between March 1, 2021, and May 31, 2024. GM cited the root cause as a supplier manufacturing and quality issues. GM’s recall remedy will be either an oil change to an oil with a different viscosity or engine replacement depending on the results of the remedy inspection procedure. To date, ODI has received 1,157 allegations of engine bearing failure. GM submitted 55,464 reports in total, with 29,752 unique VINs. ODI continues to receive allegations of L87 engine failures which fall outside of the scope of recall 25V-274. Based on GM’s recall, ODI will close this PE. NHTSA will continue to investigate complaints of engine failure outside the scope of recall 25V-274 as part ofEngineering Analysis (EA25007). To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:hard Parts Internal/mechanical
On January 16, 2025, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE25001 after receiving complaints and field reports concerning engine failures in MY2019-2024 GM’s full-size truck and SUV T1XX platform equipped with the L87 6.2L V8 engine. These complainants alleged engine bearing failures resulting in knocking and growling noises from the engine’s bottom end and in some cases more severe consequences such as broken connecting rods leading to engine damage, or engine failure. If the engine fails during vehicle operation, the vehicle will lose propulsion, increasing the risk of a crash. On April 24, 2025, GM issued recall 25V-274 to address the concern with L87 engines produced between March 1, 2021, and May 31, 2024. GM cited the root cause as a supplier manufacturing and quality issues. GM’s recall remedy will be either an oil change to an oil with a different viscosity or engine replacement depending on the results of the remedy inspection procedure. To date, ODI has received 1,157 allegations of engine bearing failure. GM submitted 55,464 reports in total, with 29,752 unique VINs. ODI continues to receive allegations of L87 engine failures which fall outside of the scope of recall 25V-274. Based on GM’s recall, ODI will close this PE. NHTSA will continue to investigate complaints of engine failure outside the scope of recall 25V-274 as part ofEngineering Analysis (EA25007). To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
On January 16, 2025, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE25001 after receiving complaints and field reports concerning engine failures in MY2019-2024 GM’s full-size truck and SUV T1XX platform equipped with the L87 6.2L V8 engine. These complainants alleged engine bearing failures resulting in knocking and growling noises from the engine’s bottom end and in some cases more severe consequences such as broken connecting rods leading to engine damage, or engine failure. If the engine fails during vehicle operation, the vehicle will lose propulsion, increasing the risk of a crash. On April 24, 2025, GM issued recall 25V-274 to address the concern with L87 engines produced between March 1, 2021, and May 31, 2024. GM cited the root cause as a supplier manufacturing and quality issues. GM’s recall remedy will be either an oil change to an oil with a different viscosity or engine replacement depending on the results of the remedy inspection procedure. To date, ODI has received 1,157 allegations of engine bearing failure. GM submitted 55,464 reports in total, with 29,752 unique VINs. ODI continues to receive allegations of L87 engine failures which fall outside of the scope of recall 25V-274. Based on GM’s recall, ODI will close this PE. NHTSA will continue to investigate complaints of engine failure outside the scope of recall 25V-274 as part ofEngineering Analysis (EA25007). To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE21010 · Air Bag Malfunction
Opened Apr 9, 2021 · Closed Aug 24, 2023
Status: closed (inferred from source dates) · Air Bags; Air Bags:frontal; Air Bags:frontal:driver Side:inflator Module; Air Bags:srs Malfunction Warning Lamp/light
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Additional source detail variants (4)
Air Bags:frontal:driver Side:inflator Module
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags:frontal
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags:srs Malfunction Warning Lamp/light
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.