IllustrationVehicle has less than 64,000 miles and seems to be having engine issues. ESC message with engine power reduced. Cannot even drive the vehicle any longer. Cannot get it into a shop for a month and will have to have it towed.
2021 GMC Sierra 1500
Owner reports · Recalls · Investigations
More warning signs than most Sierra 1500 years
Owner complaints for the 2021 GMC Sierra 1500 are substantially higher than the model-year median of 181.
About this comparison →How this year compares
Owner complaints by model year
Compare all Sierra 1500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 117 of 563 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine. Review the 299 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 134 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 73 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
5 crash reports6 fire reports2 injury reports
Engine complaints
299 reportsThe contact owns a 2021 GMC Sierra 1500. The contact stated that while driving 65 - 70 MPH, there was a knocking sound coming from the vehicle and the vehicle shut off. There were unknown warning lights illuminated. The vehicle was towed to an unknown location. The local dealer was contacted. The vehicle was not diagnosed or rep…
Read full complaint
The contact owns a 2021 GMC Sierra 1500. The contact stated that while driving 65 - 70 MPH, there was a knocking sound coming from the vehicle and the vehicle shut off. There were unknown warning lights illuminated. The vehicle was towed to an unknown location. The local dealer was contacted. The vehicle was not diagnosed or repaired. The vehicle was taken to an independent mechanic who determined that there was a solid engine bottom and bearing failure. The contact was informed that the engine needed to be replaced. The vehicle was repaired. but the failure recurred, and the vehicle failed to start. The manufacturer was contacted and informed of the failure. The failure mileage was approximately 83,000.
I wanted to reach out to see if there is anything in addition to the lemon law. I bought a 2021 GMC Sierra with 38,000 miles on it around March of last year. There was a motor defect which was covered by the warranty. I was driving and it stopped in the middle of the road so I had to safely maneuver out of the main road. The tru…
Read full complaint
I wanted to reach out to see if there is anything in addition to the lemon law. I bought a 2021 GMC Sierra with 38,000 miles on it around March of last year. There was a motor defect which was covered by the warranty. I was driving and it stopped in the middle of the road so I had to safely maneuver out of the main road. The truck was towed to my house with 45,184 miles on it, until the GMC dealership could take it in to inspect. They did take a while to get me a rental because everything was backed up. They said they could rent me out a truck due to not being their brand and that it only covers a certain amount. It got taken in by the dealership on 7/15/2024 and ended up getting the truck back repaired on 8/27. I did get the truck back and have been having it, I am just worried about it breaking down or anything of that nature. I just wanted to know if there is any further process I should do or since they repaired it there should be no issue.
First engine blown 31,904 miles, Lifter failure. Replaced with re-manufactured engine. Second engine failure at 68,000 miles, Piston rod failure. Piston blew thru engine block and engine bay caught on fire.
I had purchased a 2021 GMC Sierra equipped with the 6.2 liter motor in October of 2021. Within two weeks, my engine was experiencing problems. There was no service lights on the dash, and my truck suddenly shut off while on a busy road. I was able to coast to the side of the road, however it was a driving lane with no should…
Read full complaint
I had purchased a 2021 GMC Sierra equipped with the 6.2 liter motor in October of 2021. Within two weeks, my engine was experiencing problems. There was no service lights on the dash, and my truck suddenly shut off while on a busy road. I was able to coast to the side of the road, however it was a driving lane with no shoulder which made the situation dangerous. I was able to restart the engine after some time, and eventually get the vehicle off of the roadway, thankfully I got out of the driving lane without being struck by another vehicle. The truck had approximatley 1000 miles at this time and was brand new. I ended up needing a complete engine replacement due to failed crank bearings and connecting rods. I was told it was a crankshaft issue. After the complete motor replacement, sometime during the next year I was experiencing oil burning issues. On this second motor, a GM dealer had to completley rebuild the top end of the motor and install new piston rings. This is now a total of two motor failues in under 30,000 miles.
Tried to accelerate and heard a loud pop and the truck didn’t accelerate. Pretty much went idle in the middle of the road. The check engine light, the traction control light, and the ABS light all came on. I would press on the gas and it would rev but nothing would happen till a few seconds later the RPM’s would shoot up and you…
Read full complaint
Tried to accelerate and heard a loud pop and the truck didn’t accelerate. Pretty much went idle in the middle of the road. The check engine light, the traction control light, and the ABS light all came on. I would press on the gas and it would rev but nothing would happen till a few seconds later the RPM’s would shoot up and you could tell it was trying to get going but didn’t very slowly and I would hear a clicking noise every time it was around the second gear. It put my children and myself in danger because traffic was heavy with vehicles going 70+mph merging into one lane. Took it to a dealership and they stated it was the the push rod and camshaft were damaged and all 16 lifters should be replaced and camshaft also. No, the vehicle has not been inspected by any of those except a car dealership and a mechanic. This problem first appeared the day it happened and continued after. Even took it to a mechanic and had all 16 lifters changed and problem still persists. Spent over $6,000 on a brand new truck and it is still undrivable because every time you get in to drive it the cylinder #2 misfires.
See attached vehicle repair orders/Carfax/vehicle registration. The trucks transmission has been slipping/jerking hard since I pulled off the lot at dealer ship. Its burning oil no leaks has been doing so since the day I drove off the lot at dealership. I have asked to fix or address and problem still exist. They sold vehi…
Read full complaint
See attached vehicle repair orders/Carfax/vehicle registration. The trucks transmission has been slipping/jerking hard since I pulled off the lot at dealer ship. Its burning oil no leaks has been doing so since the day I drove off the lot at dealership. I have asked to fix or address and problem still exist. They sold vehicle as everything was working The Left head light wasn’t working the day I drove off the lot didn’t notice until I got home I reached back out to dealer to explain and said light had a short in kept truck for almost a week said the were going to replace the head light and never did. The remote start wasn’t working the same day i purchased the truck but sold it as everything is working. I went to try it as I was getting ready to leave dealership and did nothing. Then I discovered the fog lights were missing, and dealer said oh there was never any in the truck but if you read the service paper work there was lights in truck. Took truck back to address the issues the next day or so after purchase I was told to bring truck back the following week. All the conditions still exist and I should not be having any of these issues as the sold vehicle nothing wrong. They even had an October inspection saying everything was SAT but I get in truck no fog lights and left head lamp is not working but they performed an 360 inspection….yeah no way… This truck is doing the same as my 2021 chevy Silverado but there is nothing wrong with vehicle according to dealership. Sold A Lemon if you asked me… ***Highlighted in yellow is a recall that the dealership has not done nor can they find anything on the recall**** *****Power train**** Recall date 2024-10-24 Recall no. 24V797000 General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel en
Motor seized up while going around 65mph. Truck lost all power and would not start brought to dealer and they said that it was the crankshaft bearings and something with the connecting rods, the deal told me that they don’t know what to do and is waiting on GM. There is a recall for these issues but no fix. I’m just waiting for …
Read full complaint
Motor seized up while going around 65mph. Truck lost all power and would not start brought to dealer and they said that it was the crankshaft bearings and something with the connecting rods, the deal told me that they don’t know what to do and is waiting on GM. There is a recall for these issues but no fix. I’m just waiting for the dealer to tell me what’s next but they don’t even know.
Engine power reduced, could not accelerate, fuel pump issue and was bucking the engine Went to dealer and complained as gmc not working to help me, dealer fixed issue but said no other complaints out there and car was fixed, gmc called me several times and keeps saying no issues with the vin associated. The car was fixed but I …
Read full complaint
Engine power reduced, could not accelerate, fuel pump issue and was bucking the engine Went to dealer and complained as gmc not working to help me, dealer fixed issue but said no other complaints out there and car was fixed, gmc called me several times and keeps saying no issues with the vin associated. The car was fixed but I am stuck with a truck that is probably not saleable once these issues continue. This issue happened initially with 30 k on it and dealer could not find the issue and this times at 61500 happened again
was getting on the interstate whenever i hit 70 mph just heard a hard knock in the engine and truck was driving rough. the truck it self dropped to 60mph. before it occurred there was no check engine light on or anything. after i had the dash light up with engine light, brake light, stability light. about a week later took it to…
Read full complaint
was getting on the interstate whenever i hit 70 mph just heard a hard knock in the engine and truck was driving rough. the truck it self dropped to 60mph. before it occurred there was no check engine light on or anything. after i had the dash light up with engine light, brake light, stability light. about a week later took it to the dealer they said it was fuel injectors they replaced it took them about 2weeks but the problem wasn’t resolved but then stated it was the lifters which they said it almost common for this to happened. so i took it somewhere else to get replaced and they said yes it was the lifters and i needed to replace the camshaft because when the lifters go out it will damage the camshaft. all they did to diagnose my problem was hear it was ticking and the knocks also with the codes from the dealer diagnosis. after my repairs it was expensive least to say
Official recalls
726V083000 · Power Train:automatic Transmission:control Module:software; Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
Feb 12, 2026
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence & remedy
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
Additional source detail variants (2)
Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
Power Train:automatic Transmission:control Module:software
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
25V274000 · Engine And Engine Cooling:engine:hard Parts Internal/mechanical
Apr 24, 2025
General Motors LLC (GM) is recalling certain 2021-2024 Cadillac Escalade and Escalade ESV, Chevrolet Silverado 1500, Suburban, and Tahoe, GMC Sierra 1500, Yukon, and Yukon XL vehicles equipped with a 6.2L V8 gas engine. The connecting rod and/or crankshaft engine components may have manufacturing defects that can lead to engine damage and engine failure.
Consequence & remedy
Consequence: Engine failure increases the risk of a crash.
Remedy: Dealers will inspect the engine, and as necessary, repair or replace the engine. For vehicles that pass inspection, dealers will add higher viscosity oil, install 6 oil fill cap, replace the oil filter, and update the owner's manual. Repairs will be performed free of charge. Owner notification letters were mailed June 18, 2025. Owners may contact Cadillac customer service at 1-800-333-4223, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is N252494000.
24V797000 · Power Train:automatic Transmission:control Module:software; Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
Oct 24, 2024
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence & remedy
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
Additional source detail variants (2)
Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
Power Train:automatic Transmission:control Module:software
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
21V985000 · Tires:temporary/emergency Spare Tire
Dec 16, 2021
General Motors (GM) is recalling certain 2019-2021 GMC Sierra 1500 and Silverado 1500 vehicles equipped with certain accessory road tires and a 17" spare tire. The 17" spare tire provided with the vehicle is not compatible for use with the accessory wheels, which can cause the anti-lock brake system (ABS) to not function properly under certain conditions.
Consequence & remedy
Consequence: An ABS system that does not function properly can increase the risk of a crash.
Remedy: Dealers will provide a new 17" spare tire and wheel assembly that is compatible with the accessory wheels, free of charge. Dealers will also apply a new spare tire information label, and provide owners with an owner's manual insert clarifying which spare tire to use with the accessory road tires and with the 17" original tires. Owner notification letters were mailed February 7, 2022. Owners may contact GM customer service at 1-800-462-8782 or GMC customer service at 1-800-462-8782. GM's number for this recall is N212346510.
20V811000 · Seat Belts; Seat Belts:critical Fasteners
Dec 23, 2020
General Motors, LLC (GM) is recalling certain 2020 Chevrolet Bolt EV and 2021 GMC Canyon and Sierra 1500, 2500 and 3500, Yukon, Yukon XL, Cadillac Escalade and Escalade ESV and Chevrolet Blazer, Camaro, Colorado, Equinox, Silverado 1500, 2500 and 3500, Suburban and Tahoe vehicles. Incorrect bolts may have been used at one or more fastening locations to secure the seat belts to the vehicle. If an incorrect bolt was used, the seat belt may not be properly attached to the vehicle.
Consequence & remedy
Consequence: If a seat belt assembly is not properly attached to the vehicle, the seat belt may not properly restrain an occupant in the event of a crash, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the suspect bolts, free of charge. The recall began January 29, 2021. Owners may contact GMC customer service at 1-800-462-8785, Cadillac customer service at 1-800-458-8006, or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202322230.
Additional source detail variants (2)
Seat Belts:critical Fasteners
General Motors, LLC (GM) is recalling certain 2020 Chevrolet Bolt EV and 2021 GMC Canyon and Sierra 1500, 2500 and 3500, Yukon, Yukon XL, Cadillac Escalade and Escalade ESV and Chevrolet Blazer, Camaro, Colorado, Equinox, Silverado 1500, 2500 and 3500, Suburban and Tahoe vehicles. Incorrect bolts may have been used at one or more fastening locations to secure the seat belts to the vehicle. If an incorrect bolt was used, the seat belt may not be properly attached to the vehicle.
Consequence: If a seat belt assembly is not properly attached to the vehicle, the seat belt may not properly restrain an occupant in the event of a crash, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the suspect bolts, free of charge. The recall began January 29, 2021. Owners may contact GMC customer service at 1-800-462-8785, Cadillac customer service at 1-800-458-8006, or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202322230.
Seat Belts
General Motors, LLC (GM) is recalling certain 2020 Chevrolet Bolt EV and 2021 GMC Canyon and Sierra 1500, 2500 and 3500, Yukon, Yukon XL, Cadillac Escalade and Escalade ESV and Chevrolet Blazer, Camaro, Colorado, Equinox, Silverado 1500, 2500 and 3500, Suburban and Tahoe vehicles. Incorrect bolts may have been used at one or more fastening locations to secure the seat belts to the vehicle. If an incorrect bolt was used, the seat belt may not be properly attached to the vehicle.
Consequence: If a seat belt assembly is not properly attached to the vehicle, the seat belt may not properly restrain an occupant in the event of a crash, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the suspect bolts, free of charge. The recall began January 29, 2021. Owners may contact GMC customer service at 1-800-462-8785, Cadillac customer service at 1-800-458-8006, or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202322230.
20V792000 · Seat Belts; Seat Belts:critical Fasteners
Dec 17, 2020
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence & remedy
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
Additional source detail variants (2)
Seat Belts:critical Fasteners
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
Seat Belts
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
20V684000 · Tires
Nov 5, 2020
General Motors LLC (GM) is recalling certain 2020 Buick Enclave, Cadillac XT5, GMC Acadia and Chevrolet Traverse vehicles and 2020-2021 Chevrolet Silverado 1500, GMC Sierra 1500 vehicles. The vehicles may have been manufactured with Continental tires that were overcured.
Consequence & remedy
Consequence: Overcured tires may experience a carcass break in the sidewall resulting in a sudden air loss or could develop a belt edge separation which could lead to partial or full tread/belt loss. Either condition increases the risk of a crash.
Remedy: GM will notify owners, and dealers will inspect vehicles and replace tires that have DOT number and production mold number combinations identified by Continental, free of charge. The recall began December 17, 2020. Owners may contact GMC customer service at 1-888-988-7267, Buick customer service at 1-866-608-8080, Chevrolet customer service at 1-800-222-1020 or Cadillac customer service at 1-800-458-8006. GM's number for this recall is N202319030.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
5EA26005 · Loss Of Motive Power Due To Engine Failure Post Recall Remedy
Opened Aug 20, 2026 · No close date supplied
Status: open (inferred from source dates) · Engine
On January 16, 2026, the Office of Defects Investigation (ODI) opened Recall Query RQ26001. This investigation was opened to assess the remedy effectiveness of Recall 25V-274. ODI has received complaints alleging engine failure in vehicles after the recall remedy had been completed, whether that remedy involved an oil viscosity change or a complete engine replacement. General Motors (GM) issued Recall 25V-274 to address concerns of engine failure in the L87 engines produced between March 1, 2021 and May 31, 2024. GM cited the root cause as a supplier manufacturing and quality issue. GM’s recall remedy for Recall 25V-274 consisted of two different repairs, either an oil viscosity change or an engine replacement, based on the results of the remedy inspection procedure. ODI continues to receive reports of engine failures after the completion of the recall remedy. To date, ODI has received 499 complaints alleging post-remedy engine failure in vehicles subject to Recall 25V-274, 473 of which involved an oil viscosity change and 26 a complete engine replacement. Additionally, ODI has received 191 reports of L87 engine failures in engines produced after the production period cited in Recall 25V-274. GM reported receiving 6,953 complaints of post-remedy engine failure. ODI is opening this Engineering Analysisto continue investigating complaints of post-remedy engine failure. ODI is expanding the scope of this Investigation to include engines produced after the production period cited in the recall. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
RQ26001 · Loss Of Motive Power Due To Engine Failure Post Recall Remedy
Opened Jan 16, 2026 · Closed Aug 20, 2026
Status: closed (inferred from source dates) · Engine
On January 16, 2026, the Office of Defects Investigation (ODI) opened Recall Query RQ26001. This investigation was opened to assess the remedy effectiveness of Recall 25V-274. ODI has received complaints alleging engine failure in vehicles after the recall remedy had been completed, whether that remedy involved an oil viscosity change or a complete engine replacement. General Motors (GM) issued Recall 25V-274 to address concerns of engine failure in the L87 engines produced between March 1, 2021 and May 31, 2024. GM cited the root cause as a supplier manufacturing and quality issue. GM’s recall remedy for Recall 25V-274 consisted of two different repairs, either an oil viscosity change or an engine replacement, based on the results of the remedy inspection procedure. ODI continues to receive reports of engine failures after the completion of the recall remedy. To date, ODI has received 499 complaints alleging post-remedy engine failure in vehicles subject to Recall 25V-274, 473 of which involved an oil viscosity change and 26 a complete engine replacement. GM reported receiving 6,953 complaints of post-remedy engine failure. ODI will close this RQ and continue to investigate complaints of post-remedy engine failure for Recall 25V-274 as part of an Engineering Analysis (EA26005). To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
EA25007 · Loss Of Motive Power Due To Engine Failure
Opened Oct 23, 2025 · No close date supplied
Status: open (inferred from source dates) · Engine; Engine And Engine Cooling:engine:hard Parts Internal/mechanical
The Office of Defects Investigation (ODI) has received 1,157 reports of engine bearing failure failures in the L87 6.2L engine produced by General Motors (GM). Of the 1,157 reports received, 173 are outside of the scope of recall 25V-274. These engines are installed in Model Years (MY) 2019–2024 Chevrolet Silverado 1500 and GMC Sierra 1500, and 2021-2024MY Chevrolet Suburban and Tahoe, GMC Yukon/Yukon XL, and Cadillac Escalade/Escalade ESV vehicles. The subject engine failures were investigated as part of a Preliminary Evaluation (PE25001). GM determined that these engine failures were due to multiple supplier manufacturing and quality issues. GM issued recall 25V-274 to address the supplier manufacturing and quality issues produced between March 1, 2021, and May 31, 2024. Based on the issuance of recall 25V-274, NHTSA has closed PE25001. ODI continues to receive a significant number of reports of engine failure in vehicles outside the scope of 25V-274. This presents a potential safety risk that warrants further investigation. ODI is opening this Engineering Analysis (EA) to further evaluate the scope and severity of the potential problem and to fully assess the potential safety-related issues of vehicles built outside the recall scope. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:hard Parts Internal/mechanical
The Office of Defects Investigation (ODI) has received 1,157 reports of engine bearing failure failures in the L87 6.2L engine produced by General Motors (GM). Of the 1,157 reports received, 173 are outside of the scope of recall 25V-274. These engines are installed in Model Years (MY) 2019–2024 Chevrolet Silverado 1500 and GMC Sierra 1500, and 2021-2024MY Chevrolet Suburban and Tahoe, GMC Yukon/Yukon XL, and Cadillac Escalade/Escalade ESV vehicles. The subject engine failures were investigated as part of a Preliminary Evaluation (PE25001). GM determined that these engine failures were due to multiple supplier manufacturing and quality issues. GM issued recall 25V-274 to address the supplier manufacturing and quality issues produced between March 1, 2021, and May 31, 2024. Based on the issuance of recall 25V-274, NHTSA has closed PE25001. ODI continues to receive a significant number of reports of engine failure in vehicles outside the scope of 25V-274. This presents a potential safety risk that warrants further investigation. ODI is opening this Engineering Analysis (EA) to further evaluate the scope and severity of the potential problem and to fully assess the potential safety-related issues of vehicles built outside the recall scope. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
The Office of Defects Investigation (ODI) has received 1,157 reports of engine bearing failure failures in the L87 6.2L engine produced by General Motors (GM). Of the 1,157 reports received, 173 are outside of the scope of recall 25V-274. These engines are installed in Model Years (MY) 2019–2024 Chevrolet Silverado 1500 and GMC Sierra 1500, and 2021-2024MY Chevrolet Suburban and Tahoe, GMC Yukon/Yukon XL, and Cadillac Escalade/Escalade ESV vehicles. The subject engine failures were investigated as part of a Preliminary Evaluation (PE25001). GM determined that these engine failures were due to multiple supplier manufacturing and quality issues. GM issued recall 25V-274 to address the supplier manufacturing and quality issues produced between March 1, 2021, and May 31, 2024. Based on the issuance of recall 25V-274, NHTSA has closed PE25001. ODI continues to receive a significant number of reports of engine failure in vehicles outside the scope of 25V-274. This presents a potential safety risk that warrants further investigation. ODI is opening this Engineering Analysis (EA) to further evaluate the scope and severity of the potential problem and to fully assess the potential safety-related issues of vehicles built outside the recall scope. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
PE25001 · Loss Of Motive Power Due To Engine Failure
Opened Jan 16, 2025 · Closed Oct 23, 2025
Status: closed (inferred from source dates) · Engine; Engine And Engine Cooling:engine:hard Parts Internal/mechanical
On January 16, 2025, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE25001 after receiving complaints and field reports concerning engine failures in MY2019-2024 GM’s full-size truck and SUV T1XX platform equipped with the L87 6.2L V8 engine. These complainants alleged engine bearing failures resulting in knocking and growling noises from the engine’s bottom end and in some cases more severe consequences such as broken connecting rods leading to engine damage, or engine failure. If the engine fails during vehicle operation, the vehicle will lose propulsion, increasing the risk of a crash. On April 24, 2025, GM issued recall 25V-274 to address the concern with L87 engines produced between March 1, 2021, and May 31, 2024. GM cited the root cause as a supplier manufacturing and quality issues. GM’s recall remedy will be either an oil change to an oil with a different viscosity or engine replacement depending on the results of the remedy inspection procedure. To date, ODI has received 1,157 allegations of engine bearing failure. GM submitted 55,464 reports in total, with 29,752 unique VINs. ODI continues to receive allegations of L87 engine failures which fall outside of the scope of recall 25V-274. Based on GM’s recall, ODI will close this PE. NHTSA will continue to investigate complaints of engine failure outside the scope of recall 25V-274 as part ofEngineering Analysis (EA25007). To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:hard Parts Internal/mechanical
On January 16, 2025, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE25001 after receiving complaints and field reports concerning engine failures in MY2019-2024 GM’s full-size truck and SUV T1XX platform equipped with the L87 6.2L V8 engine. These complainants alleged engine bearing failures resulting in knocking and growling noises from the engine’s bottom end and in some cases more severe consequences such as broken connecting rods leading to engine damage, or engine failure. If the engine fails during vehicle operation, the vehicle will lose propulsion, increasing the risk of a crash. On April 24, 2025, GM issued recall 25V-274 to address the concern with L87 engines produced between March 1, 2021, and May 31, 2024. GM cited the root cause as a supplier manufacturing and quality issues. GM’s recall remedy will be either an oil change to an oil with a different viscosity or engine replacement depending on the results of the remedy inspection procedure. To date, ODI has received 1,157 allegations of engine bearing failure. GM submitted 55,464 reports in total, with 29,752 unique VINs. ODI continues to receive allegations of L87 engine failures which fall outside of the scope of recall 25V-274. Based on GM’s recall, ODI will close this PE. NHTSA will continue to investigate complaints of engine failure outside the scope of recall 25V-274 as part ofEngineering Analysis (EA25007). To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
On January 16, 2025, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE25001 after receiving complaints and field reports concerning engine failures in MY2019-2024 GM’s full-size truck and SUV T1XX platform equipped with the L87 6.2L V8 engine. These complainants alleged engine bearing failures resulting in knocking and growling noises from the engine’s bottom end and in some cases more severe consequences such as broken connecting rods leading to engine damage, or engine failure. If the engine fails during vehicle operation, the vehicle will lose propulsion, increasing the risk of a crash. On April 24, 2025, GM issued recall 25V-274 to address the concern with L87 engines produced between March 1, 2021, and May 31, 2024. GM cited the root cause as a supplier manufacturing and quality issues. GM’s recall remedy will be either an oil change to an oil with a different viscosity or engine replacement depending on the results of the remedy inspection procedure. To date, ODI has received 1,157 allegations of engine bearing failure. GM submitted 55,464 reports in total, with 29,752 unique VINs. ODI continues to receive allegations of L87 engine failures which fall outside of the scope of recall 25V-274. Based on GM’s recall, ODI will close this PE. NHTSA will continue to investigate complaints of engine failure outside the scope of recall 25V-274 as part ofEngineering Analysis (EA25007). To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE21010 · Air Bag Malfunction
Opened Apr 9, 2021 · Closed Aug 24, 2023
Status: closed (inferred from source dates) · Air Bags; Air Bags:frontal; Air Bags:frontal:driver Side:inflator Module; Air Bags:srs Malfunction Warning Lamp/light
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Additional source detail variants (4)
Air Bags:frontal:driver Side:inflator Module
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags:frontal
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags:srs Malfunction Warning Lamp/light
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.