NHTSA owner reports · September 18, 2026 snapshot.
Service Brakes complaints
219 reportsClear category filter40,000 miles · Jun 6, 2018
Service BrakesCrash
WHILE IN MOTION THE BRAKE PEDAL GOES HARD AND IS DIFFICULT TO STOP. I BELIEVE THIS IS THE CAUSE OF A LOW SPEED INCIDENT I HAD EARLIER THIS YEAR. THE ISSUE OCCURRES MOSTLY AT SLOW SPEEDS IN STOP AND GO TRAFFIC. IF FEELS LIKE THE BRAKE BOOSTER FAILS AND THE PEDAL IS BOTTOMED OUT. IT HAPPENS FREQUESNTLY WHILE HAULING A TRAILER …
Read full complaint
WHILE IN MOTION THE BRAKE PEDAL GOES HARD AND IS DIFFICULT TO STOP. I BELIEVE THIS IS THE CAUSE OF A LOW SPEED INCIDENT I HAD EARLIER THIS YEAR. THE ISSUE OCCURRES MOSTLY AT SLOW SPEEDS IN STOP AND GO TRAFFIC. IF FEELS LIKE THE BRAKE BOOSTER FAILS AND THE PEDAL IS BOTTOMED OUT. IT HAPPENS FREQUESNTLY WHILE HAULING A TRAILER IN REVERSE. VERY DANGEROUS SITUATION.
NHTSA ODI #11100297
39,000 miles · May 15, 2018
Service Brakes
BRAKE FAILURE DUE TO BAD VACUUM PUMP
NHTSA ODI #11094026
70,000 miles · May 4, 2018
Service Brakes
WHILE DRIVING IN STOP AND GO TRAFFIC SPEEDS THERE HAVE BEEN A NUMBER OF OCCASIONS THAT THE BRAKE PEDAL GOES HARD AND THE TRUCK WILL NOT STOP. I HAVE NOTICED ON OTHER FORUMS THAT THIS SEEMS TO BE A COMMON ISSUE.
NHTSA ODI #11091924
58,000 miles · Apr 18, 2018
Service Brakes
I WAS DRIVING DOWN I20 IN DALLAS IN RUSH HOUR TRAFFIC, THE TRAFFIC WAS HEAVY BUT MOVING AT 70 MILES AN HOUR. I SAW BRAKE LIGHTS IN FROM OF ME, WHEN I PRESSED THE BRAKE TO SLOW DOWN THE BRAKE PEDAL WAS HARD, I COULD NOT PRESS IT WITH ONE FOOT AND I COULD NOT SLOW DOWN. I FINALLY WAS ABLE TO SLOW DOWN BY PUTTING BOTH FEET ON THE …
Read full complaint
I WAS DRIVING DOWN I20 IN DALLAS IN RUSH HOUR TRAFFIC, THE TRAFFIC WAS HEAVY BUT MOVING AT 70 MILES AN HOUR. I SAW BRAKE LIGHTS IN FROM OF ME, WHEN I PRESSED THE BRAKE TO SLOW DOWN THE BRAKE PEDAL WAS HARD, I COULD NOT PRESS IT WITH ONE FOOT AND I COULD NOT SLOW DOWN. I FINALLY WAS ABLE TO SLOW DOWN BY PUTTING BOTH FEET ON THE PEDAL WITH ALL MY WEIGHT IT FELT LIKE IT WAS FOREVER BEFORE I WAS ABLE TO SLOW DOWN. I THOUGHT I WAS GOING TO BE UNABLE TO STOP.I DROVE ANOTHER 15 MINUTES GOING VERY SLOW AND SCARED. PARKED MY TRUCK IN THE DRIVE AND HAD A TOW TRUCK PULL IT TO THE DEALERSHIP CLOSEST TO MY HOUSE. MY TRUCK ONLY HAS 58,000. I REALLY WAS SCARED FOR MY LIFE IF YOU HAVE EVER DRIVEN IN RUSH HOUR DALLAS TRAFFIC YOU UNDERSTAND . I COULD HAVE LOST MY LIFE OR BE SERIOUSLY INJURED. THE DEALERSHIP TOLD ME TODAY THEY HAD NOT HEARD OF THIS ISSUE. THE DEALERSHIP SAID THEY DOUBT GMC CAN DO ANYTHING ABOUT THE PROBLEM. THE SERVICE DEPARTMENT SAID WAS A VACUUM PUMP ON THE BREAKS. I LOOKED ON LINE AND OTHERS HAVE REPORTED THIS SAME ISSUE. I COULD HAVE BEEN KILLED. STILL SHAKING OVER THE INCIDENT . I HOPE THIS PROBLEM IS ADDRESSED BEFORE SOMEONE IS KILLED
NHTSA ODI #11088926
70,000 miles · Mar 22, 2018
Service Brakes
BRAKES LOOSE BOOST AT IDLE AFTER TOWING TRAILER. I TOWED A HEAVY TRAILER AND THEN DROPPED IT IN MY YARD. WHEN I WENT TO MOVE MY TRUCK DOWN MY DRIVEWAY AND INTO MY GARAGE I HAD NO BRAKE BOOST UNLESS I REVVED THE ENGINE.
NHTSA ODI #11080863
72,000 miles · Jan 22, 2018
Service BrakesCrash
I WAS FOLLOWING MY DAUGHTER WHO WAS EXITING THE GAS STATION AND PULLING OUT ONTO ROUTE 149. AS SHE PULLED UP TO ROUTE 149 SHE STOPPED TO CHECK TRAFFIC. I WAS BEHIND HER IN MY 2015 GMC SIERRA 1500, GOING APPROX. 2 MPH. WHEN I HIT THE BRAKES, NOTHING HAPPENED. THE TRUCK KEPT MOVING FORWARD AND I HIT THE REAR OF MY DAUGHTERS CA…
Read full complaint
I WAS FOLLOWING MY DAUGHTER WHO WAS EXITING THE GAS STATION AND PULLING OUT ONTO ROUTE 149. AS SHE PULLED UP TO ROUTE 149 SHE STOPPED TO CHECK TRAFFIC. I WAS BEHIND HER IN MY 2015 GMC SIERRA 1500, GOING APPROX. 2 MPH. WHEN I HIT THE BRAKES, NOTHING HAPPENED. THE TRUCK KEPT MOVING FORWARD AND I HIT THE REAR OF MY DAUGHTERS CAR, CRACKING THE REAR BUMPER. NO DAMAGE TO THE TRUCK BECAUSE I WAS ONLY GOING A COUPLE MPH, LUCKILY MY DAUGHTER HAD HER FOOT ON THE BREAK OF HER CAR, OTHERWISE I WOULD HAVE PUSHED HER RIGHT INTO ONCOMING TRAFFIC. THE FACT THAT SHE HAD HER FOOT ON THE BRAKE IS WHAT STOPPED MY TRUCK. WE BOTH BACKED UP AND GOT OUT OF THE INTERSECTION, WHEN BACKING UP THE BRAKES WORKED FINE. THERE WASN'T A SPOT TO LEAVE THE TRUCK SO I HAD TO DRIVE 3 MILES BACK TO MY HOUSE. THE BRAKES WORKED PERFECTLY AFTER, NO ISSUES WHAT SO EVER. IT SEEMED LIKE AT THE SLOW SPEED THAT BRAKES DIDN'T HAVE ANY BOOST (OR PRESSURE), THE PEDAL WAS VERY VERY STIFF, IT FELT LIKE IT WAS PUSHING BACK AGAINST ME WHEN I HIT THE REAR OF MY DAUGHTERS CAR. BUT DRIVING HOME EVERYTHING WORKED PERFECT. I'M BRINGING THE TRUCK IN (APPROX. 72K MILES) TO HAVE IT LOOKED AT BUT I'M CONCERNED THE DEALER WILL NOT KNOW WHAT TO FIX AS THE ISSUE SEEMS TO BE INTERMITTENT. THIS WAS A VERY DANGEROUS INTERSECTION AND I COULD HAVE PUSHED MY DAUGHTER INTO ONCOMING TRAFFIC AND THE RESULT WOULD HAVE BEEN MUCH MUCH WORSE. SOMETHING SEEMS TO BE SERIOUSLY WRONG WITH THE BRAKES AND WHEN GOOGLING THIS ISSUE, I FOUND MANY SIMILAR ISSUES/COMPLAINTS REGARDING THE BRAKES.
NHTSA ODI #11064080
65,000 miles · Dec 18, 2017
Service Brakes
TAKATA RECALL WHEN BACKING UP BRAKE PEDAL IS NOT AT ITS NORMAL PRESSURE SEEMS TO BE ALL THE WAY DOWN SO HAVE TO PRESS BRAKE HARDER TO STOP THE TRUCK WHEN I SHIFT TO DRIVE FORWARD SAME THING APPLIES. AFTER TRUCK HAS BEEN OFF FOR SOME TIME PARKED THEN START TO DRIVE BRAKES SEEM TO BE WORKING FINE.
NHTSA ODI #11055232
44,000 miles · Dec 12, 2017
Service Brakes
BRAKES BECAME HARD TO DEPRESS AND ENGAGE WHILE VEHICLE WAS MOVING. ALMOST CRASHED VEHICLE. AFRAID TO DRIVE. BROUGHT TO DEALER. SAID IT WAS BAD BRAKE BOOSTER. AFTER DOING SOME RESEARCH, FOUND OUT SHOULD REPLACE VACUME PUMP, MASTER CYLINDER, HOSE LINE, ETC., SO I DID. 44K MILES, 3 YEAR OLD TRUCK, HAPPENED ON /12/10/17 BROUGHT…
Read full complaint
BRAKES BECAME HARD TO DEPRESS AND ENGAGE WHILE VEHICLE WAS MOVING. ALMOST CRASHED VEHICLE. AFRAID TO DRIVE. BROUGHT TO DEALER. SAID IT WAS BAD BRAKE BOOSTER. AFTER DOING SOME RESEARCH, FOUND OUT SHOULD REPLACE VACUME PUMP, MASTER CYLINDER, HOSE LINE, ETC., SO I DID. 44K MILES, 3 YEAR OLD TRUCK, HAPPENED ON /12/10/17 BROUGHT TO DEALER GARBER GMC IN FLORIDA FOR $1300 REPAIR ON 12/11/2017. NO WARNING SIGNS WHEN THIS HAPPENED. VERY DANGEROUS WHEN BRAKES FAIL WHILE VEHICLE IS IN MOTION.
NHTSA ODI #11054123
78,000 miles · Dec 8, 2017
Service Brakes
I WAS PULLING INTO A PARKING SPOT AT WORK (SLOW SPEED) AND I COULD NOT STOP THE TRUCK. I KEPT APPLYING MORE AND MORE PRESSURE TO THE BRAKE PEDAL AND IT DID NOT STOP THE TRUCK. THE TRUCK HIT THE CURB AND STOPPED, LUCKILY THERE WASN'T A ANOTHER CAR AS I WOULD HAVE HIT IT. IT CAUGHT ME A BIT OFF GUARD AS I WAS TRYING TO FIGURE O…
Read full complaint
I WAS PULLING INTO A PARKING SPOT AT WORK (SLOW SPEED) AND I COULD NOT STOP THE TRUCK. I KEPT APPLYING MORE AND MORE PRESSURE TO THE BRAKE PEDAL AND IT DID NOT STOP THE TRUCK. THE TRUCK HIT THE CURB AND STOPPED, LUCKILY THERE WASN'T A ANOTHER CAR AS I WOULD HAVE HIT IT. IT CAUGHT ME A BIT OFF GUARD AS I WAS TRYING TO FIGURE OUT WHAT JUST HAPPENED. I BACKED THE TRUCK UP ABOUT 10 FEET, BRAKES WORKED FINE IN REVERSE, AND PULLED FORWARD BACK INTO THE SPOT. AGAIN, THE BRAKES DID NOT WORK AND I AGAIN I HIT THE CURB. NO DAMAGE TO THE TRUCK, BUT BRAKES DID NOT WORK. IT FELT LIKE THE BRAKES WERE PUSHED BACK AGAINST ME. BRAKE PEDAL NEVER WENT TO THE FLOOR, I PUSHED THE PEDAL AND THERE SEEMED TO BE MORE RESISTANCE THAN NORMAL. IT DIDN'T MATTER HOW MUCH I PUSHED, THE TRUCK KEPT MOVING FORWARD. THIS HAPPENED WITH APPROXIMATELY 78,000 MILES. I WAS LATE FOR A MEETING SO I WENT INTO WORK AND LATER IN THE DAY I HAD A BREAK SO I CHECKED ON THE TRUCK. PULLED OUT OF THE PARKING SPOT AND BACK IN AND BRAKES WORKED BOTH IN REVERSE AND IN FORWARD. SO NOW WHAT TO DO????????? AT WORK I DID A QUICK GOOGLE SEARCH AND SAW THIS SIMILAR ISSUE COME UP IN A LOT OF THE SEARCH RESPONSES- AND DECIDED TO LOG IT HERE. THIS IS A HUGE ISSUE AND VERY DANGEROUS IF I WAS IN A CROWD OR PEOPLE OR AT AN INTERSECTION AND COULDN'T STOP. I CALLED GMC AND THEY SAID THEY NEVER HEARD OF ANYTHING LIKE THIS- THEY DIDN'T SEEM TO CARE, THEY SAID IF I BROUGHT THE TRUCK IN THEY WOULD SEE IF IT HAPPENED AGAIN.
NHTSA ODI #11053431
40,600 miles · Nov 22, 2017
Service Brakes
WE WANT TO REPORT A SAFETY FEATURE IN 2015 GMC SIERRA 1500. WE BOUGHT A VEHICLE BRAND NEW AND IT CURRENTLY HAS ABOUT 40,000 MILES ON THE ODOMETER. ON 11/4/2017 AFTER WE GOT OFF THE INTERSTATE 10, THE BREAK FROM THIS TRUCK STOPPED WORKING, WE HAD A DIFFICULT AND DANGEROUS TIME TO MAKE IT STOP, AND WAS LUCKY TO MANAGE TO GET INTO…
Read full complaint
WE WANT TO REPORT A SAFETY FEATURE IN 2015 GMC SIERRA 1500. WE BOUGHT A VEHICLE BRAND NEW AND IT CURRENTLY HAS ABOUT 40,000 MILES ON THE ODOMETER. ON 11/4/2017 AFTER WE GOT OFF THE INTERSTATE 10, THE BREAK FROM THIS TRUCK STOPPED WORKING, WE HAD A DIFFICULT AND DANGEROUS TIME TO MAKE IT STOP, AND WAS LUCKY TO MANAGE TO GET INTO A STORE'S PARKING. WE HAVE TO HAUL IT TO THE LOCAL GMC ON MONDAY AND FOUND OUT THE BREAK PUMP WAS BAD. THIS PROBLEM COULD CAUSE A DEADLY ACCIDENT IF WE WERE STILL IN THE FREEWAY. WE CALLED GMC TO REPORT THE PROBLEM AND THEY SAID THERE IS NOTHING THEY CAN DO. THIS PROBLEM IS SERIOUS AND NEED TO BE ADDRESSED.
NHTSA ODI #11047981
Official recalls
9Jul 1, 2021
General Motors LLC (GM) is recalling certain 2015-2016 GMC Sierra 1500, 2500, 3500, and Chevrolet Silverado 1500, 2500, and 3500 trucks. The roof-rail air bag (RRAB) inflator end cap may detach from the inflator, or the inflator sidewall may rupture.
Consequence & remedy
Consequence: A separated inflator end cap or inflator rupture can allow compressed gas to escape, resulting in the end cap or other components being propelled into the vehicle, increasing the risk of injury or crash.
Remedy: Dealers will replace the left and right side RRAB modules, free of charge. Interim owner notification letters informing owners of the safety risk were mailed on August 18, 2021. Owners will receive a second notice when the remedy is available. Phase I owner notification letters were mailed on May 5, 2022. Phase II owner notification letters are expected to be mailed on May 31, 2022. Owners may contact GMC customer service at 1-888-988-7267 or Chevrolet customer service at 1-800-222-1020. This recall supersedes NHTSA recall number 20V-736. GM's number for this recall is N202324251.
Apr 8, 2021
General Motors, LLC (GM) is recalling certain 2014-2016 Chevrolet Silverado 1500, 2015-2016 Chevrolet Tahoe, and 2014-2015 GMC Sierra 1500 vehicles that may have received an incorrect replacement tensioner cable assembly as part of a previous recall remedy or a subsequent repair. The flexible steel cable connecting the driver's seat belt to the outboard side of the seat may be repeatedly bent over the seat side shield as the driver enters and exits the vehicle causing the cable to fatigue and separate.
Consequence & remedy
Consequence: A broken pretensioner cable reduces the effectiveness of the driver's seat belt, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the driver seat belt lap pretensioner, free of charge. The recall began on May 5, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020, and GMC customer service at 1-800-462-8782. GM's number for this recall is N212330040.
Nov 25, 2020
General Motors LLC (GM) is recalling certain 2015-2016 GMC Sierra 1500 and Chevrolet Silverado 1500 and 2015 GMC Sierra 2500 and 3500, and Chevrolet Silverado 2500 and 3500 trucks. The roof-rail air bag (RRAB) inflator end cap may detach from the inflator.
Consequence & remedy
Consequence: If the end cap separates from the inflator, the compressed gas will escape and the end cap can be propelled into the vehicle, increasing the risk of injury or a crash.
Remedy: GM will notify owners, and dealers will replace the RRAB modules on the left and/or right side, free of charge. Interim owner notification letters were mailed on December 22, 2020. Owners may contact GMC customer service at 1-888-988-7267 or Chevrolet customer service at 1-800-222-1020. Note: GM filed a new recall, number 21V-504 that supersedes this recall. All vehicles previously recalled under 20V-736 will now be repaired under the new recall number 21V-504. GM's numbers for this recall are N202309680, N202309681, and N202309682.
Oct 24, 2019
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence & remedy
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Additional source detail variants (3)
Service Brakes
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:wheel Speed Sensor/tone Ring
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Electronic Stability Control (esc)
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Sep 6, 2019
General Motors LLC (GM) is recalling certain 2015-2017 Cadillac Escalade, 2014-2018 Chevrolet Silverado, GMC Sierra, 2015-2018 Chevrolet Suburban, Tahoe, GMC Yukon vehicles. The amount of vacuum created by the vacuum pump may decrease over time.
Consequence & remedy
Consequence: As the vacuum level drops, the brake assist decreases, increasing braking effort, extending the distance required to stop the vehicle, thereby increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began October 8, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438, Cadillac customer service at 1-800-458-8006 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192268490.
Sep 7, 2018
General Motors LLC (GM) is recalling certain 2015 Chevrolet Silverado 1500, Tahoe and Suburban, GMC Sierra 1500 and Yukon, and Cadillac Escalade vehicles. Electric power steering (EPS) assist may be lost momentarily, followed by a sudden return of EPS assist.
Consequence & remedy
Consequence: If EPS assist is lost and then suddenly returns, the driver may have difficulty steering the vehicle, especially at low speeds, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will update the EPS module software, free of charge. The recall began October 12, 2018. Owners may contact Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020 and GMC customer service at 1-800-462-8782. GM's number for this recall is 18289.
Jul 10, 2017
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Sep 8, 2016
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Apr 12, 2016
General Motors LLC (GM) is recalling certain model year 2014-2015 Chevrolet Silverado 1500 and GMC Sierra 1500 trucks manufactured January 29, 2013, to January 21, 2015. While entering the vehicle, the seat belt tensioner cable may be positioned such that the driver slides over it. This movement may result in the fatigue and separation of the cable.
Consequence & remedy
Consequence: If the tensioner cable separates, the driver may not be properly restrained in the event of a crash, increasing their risk of injury.
Remedy: GM will notify owners, and dealers will modify the vehicles to prevent the tensioner from being damaged. Any tensioner that has already been damaged will be replaced, free of charge. The recall began on August 11, 2016. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-462-8782. GM's number for this recall is 15822.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE18012 · Brake Vacuum Pump Failure
Opened Nov 20, 2018 · Closed Apr 10, 2022
Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Hydraulic; Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Additional source detail variants (3)
Service Brakes
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Illustration