NHTSA owner reports · September 18, 2026 snapshot.
Steering complaints
154 reportsClear category filter55,000 miles · Jun 12, 2017
EngineSteering
TL* THE CONTACT OWNS A 2014 GMC SIERRA 1500. WHILE DRIVING 5 MPH, THE STEERING WHEEL BEGAN TO STEER BACK AND FORTH INDEPENDENTLY WITHOUT WARNING. THE CONTACT STATED THAT THE ENGINE STALLED WHILE THE FAILURE WAS OCCURRING. THE VEHICLE WAS ABLE TO RESTART, BUT THE FAILURE RECURRED TWICE. THE VEHICLE WAS TAKEN TO AN UNKNOWN DEALER,…
Read full complaint
TL* THE CONTACT OWNS A 2014 GMC SIERRA 1500. WHILE DRIVING 5 MPH, THE STEERING WHEEL BEGAN TO STEER BACK AND FORTH INDEPENDENTLY WITHOUT WARNING. THE CONTACT STATED THAT THE ENGINE STALLED WHILE THE FAILURE WAS OCCURRING. THE VEHICLE WAS ABLE TO RESTART, BUT THE FAILURE RECURRED TWICE. THE VEHICLE WAS TAKEN TO AN UNKNOWN DEALER, BUT WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED. THE FAILURE MILEAGE WAS APPROXIMATELY 55,000.
NHTSA ODI #10994538
29,000 miles · Jun 12, 2017
SteeringCrashInjury
I WAS LEAVING A STORE PARKING LOT AND BEGAN A LEFT TURN WHEN THE STEERING WHEEL WAS WRENCHED OUT OF MY HANDS AS IT SPUN AROUND CAUSING MY TRUCK TO VEER SHARPLY TO THE LEFT AND TO HIT ANOTHER STATIONARY VEHICLE. GMC SERVICE DEPARTMENT SAID THE STEERING WAS BROKEN AND PROCEEDED TO REPLACE THE STEERING MODULE. I RETAINED THE OLD MO…
Read full complaint
I WAS LEAVING A STORE PARKING LOT AND BEGAN A LEFT TURN WHEN THE STEERING WHEEL WAS WRENCHED OUT OF MY HANDS AS IT SPUN AROUND CAUSING MY TRUCK TO VEER SHARPLY TO THE LEFT AND TO HIT ANOTHER STATIONARY VEHICLE. GMC SERVICE DEPARTMENT SAID THE STEERING WAS BROKEN AND PROCEEDED TO REPLACE THE STEERING MODULE. I RETAINED THE OLD MODULE AS EVIDENCE THE TIE ROD BECAME DISCONNECTED CAUSING THE ACCIDENT. NO ONE WAS SERIOUSLY INJURED ALTHOUGH I HAS THE SKIN ON MY HAND AND FOREARM RUBBED OFF BY THE STEERING WHEEL.
NHTSA ODI #10994380
73,600 miles · May 1, 2017
Electrical SystemElectronic Stability Control (esc)Steering
TRUCK HAS 73,000 MILES ON IT. WHILE DRIVING AT APPROXIMATELY 20 MPH I APPLIED THE BRAKE AND HAD THE STABILI TRACK WARNING GO OFF, AS WELL AS RADIO AND FAN SHUT OFF. AS I WAS MAKING A SLIGHT LEFT TURN THE STEERING WHEEL JERKED OUT OF MY HAND AND LOCKED UP, LEAVING ME WITH ABSOLUTELY NO CONTROL OF THE VEHICLE IN THE MIDDLE OF TR…
Read full complaint
TRUCK HAS 73,000 MILES ON IT. WHILE DRIVING AT APPROXIMATELY 20 MPH I APPLIED THE BRAKE AND HAD THE STABILI TRACK WARNING GO OFF, AS WELL AS RADIO AND FAN SHUT OFF. AS I WAS MAKING A SLIGHT LEFT TURN THE STEERING WHEEL JERKED OUT OF MY HAND AND LOCKED UP, LEAVING ME WITH ABSOLUTELY NO CONTROL OF THE VEHICLE IN THE MIDDLE OF TRAFFIC. THE STEERING WHEEL WOULD RELEASE , JERK AND LOCK REPEATEDLY, IT HAPPENED ABOUT 4 TIMES WHILE TRYING TO REGAIN CONTROL. AT THE SAME TIME WHILE APPLYING THE BRAKE I HAD VIRTUALLY NO BRAKES TO STOP THE VEHICLE. LOOKED FOR RECALLS AND ALL I FOUND WERE HUNDREDS OF SIMILAR COMPLAINTS, BUT NO SOLUTION OR RECALLS. HOW IS THIS NOT A RECALL, IT'S GROSS NEGLIGENCE... WHAT IF I WAS AT HIGHWAY SPEEDS OR TOWING MY TRAILER AT THE TIME. GM AND NHTSA NEED TO ADDRESS THIS ISSUE IMMEDIATELY BEFORE LIVES ARE LOST. AS FOR ME, I'M IN THE PROCESS OF GETTING RID OF A VEHICLE THAT I'VE HAD FOR 3 MONTHS BECAUSE OF THIS AND WILL NOT LET MY CHILDREN RIDE IN THE VEHICLE. IT'S AN INTERMITTENT PROBLEM, I'M JUST HOPING THE NEXT TIME IT DOESN'T HAPPEN AT 65MPH. *TR
NHTSA ODI #10981582
60,500 miles · Apr 16, 2017
Electrical SystemSteering
GOT A STEERING STABILITY INDICATION WHILE DRIVING ACROSS A BUMPY STRIP ON THE HIGHWAY. LATER, I WOULD GET THE INDICATOR, AND WHEN I DID A HARD TURN, I.E. 90 DEGREES, THE ENGINE WOULD DIE. THE DEALERSHIP ISOLATED THE PROBLEM TO A BROKEN GEAR IN THE ELECTRIC POWER ASSIST, AND REPLACED THE NEGATIVE POWER CABLE ON THE BATTERY. THE…
Read full complaint
GOT A STEERING STABILITY INDICATION WHILE DRIVING ACROSS A BUMPY STRIP ON THE HIGHWAY. LATER, I WOULD GET THE INDICATOR, AND WHEN I DID A HARD TURN, I.E. 90 DEGREES, THE ENGINE WOULD DIE. THE DEALERSHIP ISOLATED THE PROBLEM TO A BROKEN GEAR IN THE ELECTRIC POWER ASSIST, AND REPLACED THE NEGATIVE POWER CABLE ON THE BATTERY. THE COST OF THE REPAIR WOULD HAVE BEEN ABOUT $3600.00, BUT GM PAID ABOUT 75%. IT WAS RECOMMENDED THAT I REPLACE THE NEGATIVE CABLE EVERY 50,000 MILES BY ONE OF THE TECHNICIANS. ANOTHER PROBLEM OCCURRED ABOUT A YEAR AGO CONCERNING THE VAPOR RECOVERY SYSTEM. I GOT A CHECK ENGINE WARNING, TOOK IT TO THE DEALER AND FOUND THAT THE WHOLE SYSTEM WAS COMPLETELY COATED WITH FINE DUST. THEY REPLACED THE VAPOR COLLECTION CANISTER AND ASSOCIATED TUBES AND FILTERS AT A COST OF ABOUT $800.00. GM PICKED UP ABOUT 50%. I LATER CHANGED THE LOCATION OF THE VAPOR COLLECTION TUBE FROM THE (VERY DUSTY) WHEEL WELL, TO UNDER THE HOOD WHERE IT WAS PROTECTED FROM THE DUST. I DON'T BELIEVE EITHER OF THESE PROBLEMS TO BE LACK OF PREVENTIVE MAINTENANCE, BECAUSE NEITHER APPEAR TO BE ABLE TO BE CHECKED OR APPEAR ON REGULAR MAINTENANCE. THE VEHICLE TURNED OFF WHILE MAKING A TURN AT SLOW SPEEDS, AND THE WARNING LIGHT CAME ON AT DRIVING SPEEDS. RELOCATING THE INTAKE ON THE VAPOR RECOVERY SYSTEM APPEARS TO HAVE CURED OR DELAYED THE ONSET OF THE PROBLEM. (I ALSO REMOVE AND BLOW OUT THE FILTER AND THE INTAKE TUBE AT LEAST ONCE A YEAR.)
NHTSA ODI #10978686
59,560 miles · Apr 8, 2017
Electrical SystemElectronic Stability Control (esc)Steering
WHEN I AM DRIVING AT LOW SPEEDS AND I TURN MY STEERING WHEEL MY WHEEL LOCKS UP AND I AM UNABLE TO TURN BY VEHICLE. WHEN I AM DRIVING ON THE HIGHWAY MY DISPLAY SYSTEM GOES IN AND OUT.
NHTSA ODI #10971434
66,000 miles · Mar 30, 2017
Electrical SystemElectronic Stability Control (esc)Steering
DRIVING AT LOW SPEEDS IN RUSH HOUR TRAFFIC AND "DEGRADED STEERING" WARNING WITH CHIME SOUNDED. CLEARED ITSELF AND THEN CHIMED AGAIN WITH SAME WARNING ABOUT THREE MINUTES LATER. THIS WAS FOLLOWED BY STABILITRACK WARNING AND RED BRAKE WARNING. STEERING WAS SOMEWHAT HARDER TO TURN BUT WAS STILL BEING ASSISTED. THERE DIDN'T APPE…
Read full complaint
DRIVING AT LOW SPEEDS IN RUSH HOUR TRAFFIC AND "DEGRADED STEERING" WARNING WITH CHIME SOUNDED. CLEARED ITSELF AND THEN CHIMED AGAIN WITH SAME WARNING ABOUT THREE MINUTES LATER. THIS WAS FOLLOWED BY STABILITRACK WARNING AND RED BRAKE WARNING. STEERING WAS SOMEWHAT HARDER TO TURN BUT WAS STILL BEING ASSISTED. THERE DIDN'T APPEAR TO BE ANY DEGRADATION TO BRAKING. MAYBE THE ANTI-LOCK SYSTEM? THE A/C THEN TURNED OFF AND THE RADIO VOLUME WENT SILENT. THE STABILITRACK SWITCH, A/C CONTROLS AND RADIO CONTROLS WERE ALL INEFFECTIVE. I NOTICED THE AMP GAUGE WAS BELOW 12 AS IT SEEMED AS IF THE TRUCK ELECTRICAL SYSTEM WAS UNDERPOWERED. I DROVE TEN MILES HOME AND ALL SYSTEMS RESET BY TURNING TRUCK OFF AND STARTING IT UP AGAIN. THIS IS FIRST TIME THIS HAS HAPPENED. TRUCK HAS 66K MILES ON IT.
NHTSA ODI #10969540
25,000 miles · Mar 9, 2017
Steering
TL* THE CONTACT OWNS A 2014 GMC SIERRA 1500. WHILE THE VEHICLE WAS OPERATED, THE SERVICE POWER STEERING WARNING INDICATOR ILLUMINATED AND THE POWER STEERING FAILED. THE FAILURE WAS INTERMITTENT. THE DEALER COULD NOT REPLICATE THE FAILURE. A YEAR EARLIER, THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE POWER S…
Read full complaint
TL* THE CONTACT OWNS A 2014 GMC SIERRA 1500. WHILE THE VEHICLE WAS OPERATED, THE SERVICE POWER STEERING WARNING INDICATOR ILLUMINATED AND THE POWER STEERING FAILED. THE FAILURE WAS INTERMITTENT. THE DEALER COULD NOT REPLICATE THE FAILURE. A YEAR EARLIER, THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE POWER STEERING MOTOR NEEDED TO BE REPLACED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE CONTACT REFERENCED NHTSA CAMPAIGN NUMBER: 14V719000 (STEERING) AS A POSSIBLE SOLUTION; HOWEVER, THE VIN WAS NOT INCLUDED. THE FAILURE MILEAGE WAS APPROXIMATELY 25,000.
NHTSA ODI #10959843
40,000 miles · Feb 10, 2017
Electronic Stability Control (esc)Steering
TL* THE CONTACT OWNS A 2014 GMC SIERRA 1500. WHILE DRIVING APPROXIMATELY 45 MPH, THE STEERING WHEEL LOCKED AND THE STABILITRACK WARNING INDICATOR ILLUMINATED. THE CONTACT HAD TO STOP IN THE MIDDLE OF THE ROAD. THE VEHICLE WAS TURNED OFF AND RESTARTED NORMALLY. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOTIF…
Read full complaint
TL* THE CONTACT OWNS A 2014 GMC SIERRA 1500. WHILE DRIVING APPROXIMATELY 45 MPH, THE STEERING WHEEL LOCKED AND THE STABILITRACK WARNING INDICATOR ILLUMINATED. THE CONTACT HAD TO STOP IN THE MIDDLE OF THE ROAD. THE VEHICLE WAS TURNED OFF AND RESTARTED NORMALLY. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE VIN WAS UNKNOWN. THE APPROXIMATE FAILURE MILEAGE WAS 40,000.
NHTSA ODI #10953856
55,000 miles · Jan 24, 2017
Electrical SystemElectronic Stability Control (esc)Steering
THIS ISSUE IS RELATED TO STABILITRAK, THE ONBOARD COMPUTING SYSTEM. WHEN ON THE INTERSTATE, LOSS OF POWER CAN OCCUR. USUALLY AT HIGH SPEEDS, THE POWER JUST 'FLICKERS' ON AND OFF, SOME TIMES REPEATEDLY. THE BREAKING MECHANISM SEEMS TO BE SOMEWHAT AFFECTED BY THIS. AT SLOWER SPEEDS, THE SAME PROBLEM CAN OCCUR, BUT THE STEERING WHE…
Read full complaint
THIS ISSUE IS RELATED TO STABILITRAK, THE ONBOARD COMPUTING SYSTEM. WHEN ON THE INTERSTATE, LOSS OF POWER CAN OCCUR. USUALLY AT HIGH SPEEDS, THE POWER JUST 'FLICKERS' ON AND OFF, SOME TIMES REPEATEDLY. THE BREAKING MECHANISM SEEMS TO BE SOMEWHAT AFFECTED BY THIS. AT SLOWER SPEEDS, THE SAME PROBLEM CAN OCCUR, BUT THE STEERING WHEEL LOCKS UP AND FORCES MY TRUCK TO TURN HARD TO THE LEFT. EACH TIME THE PROBLEM OCCURS, "STABILITRAK ERROR" AND "LOSS OF TRACTION CONTROL" OR SOMETHING ALONG THE LINES OF "LOSS OF POWER, DANGER" WILL APPEAR -- ALTHOUGH, IT IS USUALLY JUST SOMETHING RELATING TO "STABILITRAK". I'VE NEARLY BEEN IN AN ACCIDENT ~3 TIMES. IT'S NO QUESTION A DANGER TO THE DRIVER AND TO PEDESTRIANS. GM HAS BEEN GETTING SUED LIKE CRAZY, AND IT'S PRETTY CLEAR THEY ARE AVOIDING THIS ISSUE BECAUSE OF THIS.
NHTSA ODI #10947427
34,000 miles · Dec 21, 2016
Electronic Stability Control (esc)EngineSteering
STEERING WHEEL SPRINGS/SNAPS (HARD) IN THE OPPOSITE DIRECTION THAT THE WHEEL IS BEING TURNED AND STEERING CONTROL IS LOST. WHEN THIS DOES NOT SHUT THE ENGINE OFF, THE ONLY WAY TO REGAIN STEERING CONTROL IS TO RESTART THE VEHICLE. WHEN THIS DOES CAUSE THE ENGINE TO SHUT OFF THE STEERING IS RESTORED WITH THE RESTART. THE STABILI …
Read full complaint
STEERING WHEEL SPRINGS/SNAPS (HARD) IN THE OPPOSITE DIRECTION THAT THE WHEEL IS BEING TURNED AND STEERING CONTROL IS LOST. WHEN THIS DOES NOT SHUT THE ENGINE OFF, THE ONLY WAY TO REGAIN STEERING CONTROL IS TO RESTART THE VEHICLE. WHEN THIS DOES CAUSE THE ENGINE TO SHUT OFF THE STEERING IS RESTORED WITH THE RESTART. THE STABILI TRAK INDICATOR APPEARS JUST FOR AN INSTANT ON THE DIC WHEN THIS HAPPENS. NOTE: THIS IS NOT THE 'SERVICE STABILI TRAK' INDICATOR BUT MORE LIKE STABILI TRAK HAS BEEN ACTIVATED INDICATOR. THIS HAPPENED FIRST IN REVERSE WHILE BACKING INTO A PARKING SPOT. (THREE TIMES IN REVERSE). THEN IT STARTED HAPPENING IN DRIVE, TWICE WHILE PULLING OUT FROM A STOP SIGN AND ONCE WHILE DOING 15-20 MPH TURNING ONTO A SIDE STREET. THE 15-20 MPH TURNING INSTANCE CAUSED THE ENGINE TO SHUT OFF, STEERING BECAME NON EXISTENT FOR AN INSTANT AND THEN VERY VERY HEAVY. I CROSSED THE OTHER LANE OF TRAFFIC AND ALMOST LANDED IN THE DITCH. THE TRUCK HAS BEEN AT THE DEALERSHIP TWICE FOR A TOTAL OF 14 DAYS, BOTH TIMES 'CANNOT DUPLICATE' WAS THE RESULT. NO CODES ARE BEING GENERATED FROM THESE INSTANCES. CAUSE IS UNKNOWN. LOOSE VOLTAGE OR HIGH RESISTANCE TO GROUNDS MAYBE. THIS HAS HAPPENED IN HOT AND COLD WEATHER, RUNNING AC OR HEATER OR NEITHER. THERE IS NO PATTERN. PLEASE HELP.
NHTSA ODI #10936655
Official recalls
9Apr 8, 2021
General Motors, LLC (GM) is recalling certain 2014-2016 Chevrolet Silverado 1500, 2015-2016 Chevrolet Tahoe, and 2014-2015 GMC Sierra 1500 vehicles that may have received an incorrect replacement tensioner cable assembly as part of a previous recall remedy or a subsequent repair. The flexible steel cable connecting the driver's seat belt to the outboard side of the seat may be repeatedly bent over the seat side shield as the driver enters and exits the vehicle causing the cable to fatigue and separate.
Consequence & remedy
Consequence: A broken pretensioner cable reduces the effectiveness of the driver's seat belt, increasing the risk of injury.
Remedy: GM will notify owners, and dealers will replace the driver seat belt lap pretensioner, free of charge. The recall began on May 5, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020, and GMC customer service at 1-800-462-8782. GM's number for this recall is N212330040.
Oct 24, 2019
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence & remedy
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Additional source detail variants (3)
Service Brakes
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:wheel Speed Sensor/tone Ring
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Electronic Stability Control (esc)
General Motors LLC (GM) is recalling certain 2015-2020 Chevrolet Suburban, Tahoe, and GMC Yukon, and 2014-2018 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles equipped with a 5.3-liter engine, a 3.08-ratio rear axle and four-wheel drive. If a wheel-speed sensor fails, while the vehicle is traveling between 41 and 60 mph in four-wheel or automatic mode, the Electronic-Brake Control Module (EBCM) software may activate the driveline-protection system.
Consequence: Unintended activation of the driveline-protection system will cause unintended braking on the wheel on the opposite side of the failed sensor, causing the vehicle to pull to one side unexpectedly, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the EBCM, free of charge. The recall began December 11, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192261050.
Sep 6, 2019
General Motors LLC (GM) is recalling certain 2015-2017 Cadillac Escalade, 2014-2018 Chevrolet Silverado, GMC Sierra, 2015-2018 Chevrolet Suburban, Tahoe, GMC Yukon vehicles. The amount of vacuum created by the vacuum pump may decrease over time.
Consequence & remedy
Consequence: As the vacuum level drops, the brake assist decreases, increasing braking effort, extending the distance required to stop the vehicle, thereby increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will reprogram the Electronic Brake Control Module, free of charge. The recall began October 8, 2019. Owners may contact Chevrolet customer service at 1-800-630-2438, Cadillac customer service at 1-800-458-8006 or GMC customer service at 1-800-462-8782. GM's number for this recall is N192268490.
Apr 26, 2018
General Motors LLC (GM) is recalling certain 2009-2014 Chevrolet Silverado HD and GMC Sierra HD, 2009 GMC Topkick 5000, 6000, 7000 and 8000 Series and Isuzu F Series, and 2009-2018 Chevrolet Express, and GMC Savana vehicles, equipped with certain Plastic-Handle Fire Extinguishers or Push Button 'Pindicator' Fire Extinguishers. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.
Remedy: GM will notify owners, instructing them to contact Kidde to get a replacement fire extinguisher, free of charge. The recall began June 11, 2018. Owners may contact Chevrolet customer service at 1-800-222-1020, GMC customer service at 1-800-462-8782, and Isuzu customer service at 1-866-441-9638. GM's number for this recall is 18146.
Jul 10, 2017
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2014-2016 Buick Lacrosse and Chevrolet Spark EV, Caprice PPV and SS vehicles, 2014-2017 Buick Encore and Chevrolet Corvette, Silverado 1500 and GMC Sierra 1500 vehicles, 2015-2016 Cadillac Escalade and Escalade ESV, Chevrolet Tahoe, Trax, Suburban and Silverado 2500 and 3500 and GMC Yukon and Yukon XL vehicles, and 2015-2017 GMC Sierra HD 2500 and 3500 vehicles. While being previously remedied for recall 16V-651, the affected vehicles may not have received the complete software update necessary to remedy the recall condition. Without the update, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on August 4, 2017. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 17287.
Jun 29, 2017
General Motors LLC (GM) is recalling certain 2014 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles. The vehicles may have a temporary loss of electric power steering (EPS) assist, especially during low-speed turning maneuvers.
Consequence & remedy
Consequence: If EPS assist is lost and then returns, the driver might lose temporary control of the steering wheel, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will update the EPS module software, free of charge. The recall began on August 10, 2017. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-432-8782. GM's number for this recall is 17276.
Sep 8, 2016
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence & remedy
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Additional source detail variants (3)
Seat Belts:pretensioner
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal:sensor/control MODULE-INACTIVE
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Air Bags:frontal
General Motors LLC (GM) is recalling certain model year 2015-2017 Chevrolet Silverado 2500 HD, 3500 HD, Tahoe, Suburban, GMC Sierra 2500 HD and 3500 HD, GMC Yukon, GMC Yukon XL, Cadillac Escalade and Cadillac Escalade ESV vehicles and 2014-2017 Chevrolet Corvette, Silverado 1500, Trax, Caprice Police Pursuit Vehicle, GMC Sierra 1500, Buick Encore, and 2014-2016 Buick Lacrosse, Chevrolet Spark EV and SS vehicles. In the affected vehicles, certain driving conditions may cause the air bag sensing and diagnostic module (SDM) software to activate a diagnostic test. During this test, deployment of the frontal air bags and the seat belt pretensioners would not occur in the event of a crash.
Consequence: A failure of the front air bags or seat belt pretensioners to deploy in the event of a crash necessitating deployment increases the risk of injury to the driver and front passenger.
Remedy: GM will notify owners, and dealers will reflash the SDM software. Vehicles that have had a previous air bag deployment will have the SDM replaced. These repairs will be performed free of charge. The recall began on October 13, 2016. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 16007.
Apr 12, 2016
General Motors LLC (GM) is recalling certain model year 2014-2015 Chevrolet Silverado 1500 and GMC Sierra 1500 trucks manufactured January 29, 2013, to January 21, 2015. While entering the vehicle, the seat belt tensioner cable may be positioned such that the driver slides over it. This movement may result in the fatigue and separation of the cable.
Consequence & remedy
Consequence: If the tensioner cable separates, the driver may not be properly restrained in the event of a crash, increasing their risk of injury.
Remedy: GM will notify owners, and dealers will modify the vehicles to prevent the tensioner from being damaged. Any tensioner that has already been damaged will be replaced, free of charge. The recall began on August 11, 2016. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-462-8782. GM's number for this recall is 15822.
Jan 13, 2014
General Motors is recalling certain 2014 model year Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles, and 2015 model year Cadillac Escalade and Escalade ESV; Chevrolet Silverado HD; and GMC Sierra HD, Yukon, and Yukon XL, equipped with a 4.3L engine or 5.3L engine.
Consequence & remedy
Consequence: The overheated exhaust components may melt nearby plastic parts and may result in an engine fire.
Remedy: General Motors will notify owners, and dealers will reprogram the engine control module, free of charge. The recall began on January 16, 2014. Owners may contact Chevrolet at 1-800-222-1020 and GMC at 1-800-462-8782. General Motors' number for this recall is 14008.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE18012 · Brake Vacuum Pump Failure
Opened Nov 20, 2018 · Closed Apr 10, 2022
Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Hydraulic; Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Additional source detail variants (3)
Service Brakes
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Service Brakes, Hydraulic:power Assist:vacuum
On November 20, 2018, the Office of Defects Investigations (ODI) opened PE18-012 to investigate instances of sudden onset of a hard brake pedal that could result in extended stopping distance due to an issue with the brake assist vacuum pump in model year (MY) 2014 through 2016 GMC Sierra 1500 and Chevrolet Silverado 1500 series pickup trucks and MY 2015 through 2016 Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, and GMC Yukon SUVs.If the brake assist vacuum pump fails to operate as intended, the amount of brake power assist supplied to the driver can be significantly reduced, extending the subject vehicle stopping distance. GM stated that the root cause of pump failures was due to foreign debris such as oil sludge in the engine oil. GM stated that this debris can become trapped by the oil inlet filter screen. Under normal operation, this screen allows a small amount of oil into the brake vacuum pump. The foreign debris can, over time, clog the pump which can cause a loss of lubrication and a reduction in the amount of vacuum produced leading to a hard pedal and extended stopping distance.On December 13, 2018, GM issued a Special Coverage (N182202780) for the brake vacuum pump issue in MY 2014-2017 trucks and 2015-2017 SUVs on the K2XX platform for 6 years or 72,000 miles. Special Coverage repair includes the replacement of the vacuum pump and vacuum pump belt. Consumers received notification of the coverage via mail. On September 6, 2019, GM notified NHTSA that it was conducting safety recall 19V-645 which reprograms the electronic brake control module (EBCM) and included approximately 3.5 million trucks and SUVs. In October 2019, GM extended the terms of special coverage N182202780 to 10 years or 150,000 miles as well as now including the entire scope of recall 19V-645. In October 2020, GM expanded the scope of coverage N182202780 to include the MY 2018 Escalade and 2019 Tahoe.The remedy implemented in GM recall 19V-645 appears to be sufficient in addressing the safety-related concerns of this issue. Loss of vacuum assist now occurs at a progressive rate as well as there being a more timely warning of a brake problem to the driver through the driver information center (DIC). In view of the recall action and revision to the special coverage, this Preliminary Evaluation is closed. The agency reserves the right to take additional action if warranted by new circumstances. The ODI reports cited above are available for review online at NHTSA.gov under the identification numbers in the attached document.
Illustration