NHTSA owner reports · September 18, 2026 snapshot.
Service Brakes complaints
473 reportsClear category filterMileage unknown · Jan 14, 2022
Service Brakes
total abs brake and main brake system failure. Car was dropped off at the dealership 12/23/21 and I'm being told parts aren't going to be available until 2/28/22 at the earliest, probably longer. Ford won't provide any faster parts or a rental car coverage and this is my only means of transportation. The recall needs to provi…
Read full complaint
total abs brake and main brake system failure. Car was dropped off at the dealership 12/23/21 and I'm being told parts aren't going to be available until 2/28/22 at the earliest, probably longer. Ford won't provide any faster parts or a rental car coverage and this is my only means of transportation. The recall needs to provide this in addition to the repair or ford should buy back the car. They are causing a life threatening situation, no parts to fix it in a timely manor and no rental coverage for the owners.
NHTSA ODI #11447493
Mileage unknown · Jan 7, 2022
Air BagsService Brakes
I was driving and my abs light came on and is stuck open, my brake pad fell off on the driver side and the spindle is bent. I’m not sure what happened to my air bags on the passenger side. It looks like it tried to explode
NHTSA ODI #11446566
Mileage unknown · Dec 18, 2021
Service Brakes
The vehicles HBU continues to fail. After repairs done to the master cylinder, new tires, brake pads and rotors the condition of the car continues. The brakes continue to fail. Sound Ford (under the recall) flushed the braking system, however the condition continues. When asked about the repairs, the service manager informed me …
Read full complaint
The vehicles HBU continues to fail. After repairs done to the master cylinder, new tires, brake pads and rotors the condition of the car continues. The brakes continue to fail. Sound Ford (under the recall) flushed the braking system, however the condition continues. When asked about the repairs, the service manager informed me that the recall only covered flushing the braking system and replacing the fluid. The braking system has failed in total 3 times now. Sound Ford claims there is nothing wrong with the vehicle's braking system. The braking system continues to fail.
NHTSA ODI #11444253
Mileage unknown · Dec 17, 2021
Service Brakes
2009 FORD FUSION. CONSUMER WRITES IN REGARDS TO WORK NOT PROPERLY PERFORMED REGARDING SAFETY RECALL 19V-904. THE CONSUMER STATED AFTER HAVING THE RECALL REPAIR COMPLETED, THE BRAKES FAILED IN THE SAME MANNER THE RECALL DESCRIBED. THE MANUFACTURER STATED THE FAILURE WAS A WARRANTY ISSUE. THE VEHICLE'S WARRANTY WAS EXPIRED.
NHTSA ODI #11444138
Mileage unknown · Nov 19, 2021
Service Brakes
This vehicle had a recall on the ABS Hydraulic Control Unit it was taken to the dealer Champion Ford in Erie, PA June 14, 2021 to have it taken care of where they flushed it and put new cap on but did not replace the Hydraulic Control Unit. Shortly after that ABS light went on on the dash and car sat for awhile ( I bought car r…
Read full complaint
This vehicle had a recall on the ABS Hydraulic Control Unit it was taken to the dealer Champion Ford in Erie, PA June 14, 2021 to have it taken care of where they flushed it and put new cap on but did not replace the Hydraulic Control Unit. Shortly after that ABS light went on on the dash and car sat for awhile ( I bought car recently from coworker). After we purchased light was still on so we took it back to Champion Ford in Erie, PA and they said the Hydraulic Control Unit is bad and needs replaced and that is back ordered and it will be $813 because Ford will not pay for the recall because it is not a reasonable time for subsequent failure. The car only has 1000 miles on it since it was in for recall in June 2021. I called Ford 800 number and they cannot tell me what a reasonable time is and how long the recall is good for. Any help I could get would be appreciated. I have a new 16 year old driver driving this car so this is an extreme safety issue. PLEASE HELP. Sincerely, [XXX] INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
NHTSA ODI #11441007
Mileage unknown · Nov 11, 2021
Service Brakes
The Recall #19V-904 was performed on May 03,2021 by Walt Sweeney Ford. Mileage 61610. On 11/03 Brake Pedal went to floor and never came back. Called Ford dealer Walt Sweeney and schedule a inspection for 11/11/2021. Mileage 64630. Upon inspection it was found the same issue HCU ABS Failure. Ford will not pay for fix stating…
Read full complaint
The Recall #19V-904 was performed on May 03,2021 by Walt Sweeney Ford. Mileage 61610. On 11/03 Brake Pedal went to floor and never came back. Called Ford dealer Walt Sweeney and schedule a inspection for 11/11/2021. Mileage 64630. Upon inspection it was found the same issue HCU ABS Failure. Ford will not pay for fix stating recall expired. The recall #19v-904 has not fixed brake pedal issue.
NHTSA ODI #11440150
Mileage unknown · Oct 12, 2021
Service Brakes
I'm sending this in response to the above noted letter which indicates that we failed to take our 2009 Ford Fusion to our Ford dealer to have the brake system checked pursuant to the Safety Recall Notice 19S54/ NHTSA 19V-904 which we received in January 2020. Your statement that we have failed to take the vehicle to our local d…
Read full complaint
I'm sending this in response to the above noted letter which indicates that we failed to take our 2009 Ford Fusion to our Ford dealer to have the brake system checked pursuant to the Safety Recall Notice 19S54/ NHTSA 19V-904 which we received in January 2020. Your statement that we have failed to take the vehicle to our local dealership is incorrect; We took the vehicle to Sunset Ford, 11700 Gravois Road 63127 on 07/15/21. A short time after we dropped it off a dealer service representative called and advised us that the ABS light was on and refused to perform the work outlined in the January 2020 notice unless we agreed to pay for the diagnostic and all work associated with the ABS. I noted that the light had been on for over 7 years, the abs system had always functioned properly, had passed the Missouri safety inspection every year including that of May 2021 was diagnosed when it first occurred by Sinclair Ford to be a problem in the light circuit not the abs system referred her to the January 20 notice which specifically stated "a valve in the hydraulic control unit of the anti-lock braking system may be stuck open" and " repairs to be completed free of charge (parts and labor)" She stated she had all of the service information and recall notices in her file and none of them referred to the ABS systems in any manner...."either pay for the work or come back and pick up the car"....We picked up the car. A few days later I contacted the service department again and inquired about the recall and reviewed the situation with a different service representative. This person told me the abs system was not part of the recall but if the abs light was on the repairs were required by the NTSB. He said the cost could range between $300 up to $1500. I then posted the following in our neighborhood Paper: My wife took her 09 Ford Fusion to Sunset Ford this morning to get 2 NTSB recall issues repaired that we have been waiting for over a year for them to get the parts needed
NHTSA ODI #11436508
94,200 miles · Aug 23, 2021
Service Brakes
The contact owns a 2009 Ford Fusion. The contact stated that while attempting to stop the vehicle, the brake pedal extended to the floor and the stopping distance was extended. The cause of the failure was not yet determined. The contact indicated that the vehicle was previously serviced under the NHTSA Campaign Number: 19V90400…
Read full complaint
The contact owns a 2009 Ford Fusion. The contact stated that while attempting to stop the vehicle, the brake pedal extended to the floor and the stopping distance was extended. The cause of the failure was not yet determined. The contact indicated that the vehicle was previously serviced under the NHTSA Campaign Number: 19V904000 (Service Brakes, Hydraulic) however, the failure occurred. The local dealer and manufacturer were notified of the failure. The failure mileage was 94,200.
NHTSA ODI #11430177
Mileage unknown · Aug 2, 2021
Service Brakes
2009 FORD FUSION. CONSUMER WRITES IN REGARDS TO NHTSA SAFETY RECALL 19V-904. THE CONSUMER STATED THE DEALER WOULD NOT ANSWER OR RETURN CALLS SO THE RECALL REPAIR COULD BE SCHEDULED. *JS
NHTSA ODI #11427398
Mileage unknown · Jul 27, 2021
Service Brakes
Got a ticket on June23rd the breaks were low and I couldn't come to complete stop checked the break fluid level and it was full. June 28th Breaks completely went out without no warning signs nothing while I was driving had to stop with the emergency brake.I had car towed to Sterling Ford June 29.I'm not the original owner so I h…
Read full complaint
Got a ticket on June23rd the breaks were low and I couldn't come to complete stop checked the break fluid level and it was full. June 28th Breaks completely went out without no warning signs nothing while I was driving had to stop with the emergency brake.I had car towed to Sterling Ford June 29.I'm not the original owner so I had no idea about the recall and I purchased the car June 2nd in Gardena California where I'm from now stranded in Houston Texas.
NHTSA ODI #11426738
Official recalls
6Mar 10, 2021
Ford Motor Company (Ford) is recalling certain 2007-2011 Ranger, 2006-2012 Fusion, Lincoln Zephyr, Lincoln MKZ, 2006-2011 Mercury Milan, 2007-2010 Ford Edge, and Lincoln MKX vehicles. The driver's side air bag inflator may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will replace the driver-side airbag inflator or module with an alternate one, free of charge. Owner notification letters were mailed on April 9, 2021 for the passenger side, and November 14, 2022 for the driver side. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S12.
Feb 16, 2021
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Additional source detail variants (3)
Air Bags:frontal:passenger Side:inflator Module
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Air Bags:frontal:driver Side:inflator Module
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Air Bags:frontal
Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.
Dec 18, 2019
Ford Motor Company (Ford) is recalling certain 2006-2010 Ford Fusion, Mercury Milan, Lincoln Zephyr and MKZ vehicles. The valves within the ABS Hydraulic Control Units (HCU) may react with brake fluids containing specific corrosion preventative additives. This reaction may cause the valves to not close properly.
Consequence & remedy
Consequence: If the valves do not properly close, additional brake pedal travel may be required to stop the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will flush the brake system with DOT 4 fluid and install a new brake fluid reservoir cap. In addition, the HCU will be tested to detect a possible stuck valve condition, replacing the HCU as necessary. All services will be performed free of charge. The recall began April 1, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S54.
Jan 11, 2018
Ford Motor Company (Ford) is recalling certain 2013 Ford Mustang vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Ford is recalling certain 2010 Ford Edge, Fusion, Mustang and Ranger, Lincoln MKX and Zephyr/MKZ, and Mercury Milan vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Ford is also recalling certain 2009 Ford Edge, Fusion, Mustang and Ranger, Lincoln MKX and Zephyr/MKZ, and Mercury Milan vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules, used as original equipment or replacement equipment (such as after a vehicle crash necessitating replacement of the original air bags), that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
Jan 10, 2017
Ford Motor Company (Ford) is recalling certain 2012 Ford Fusion and Mustang and Lincoln Zephyr and MKZ vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Ford is recalling certain 2009 Ford Ranger, Edge, Fusion and Mustang, Lincoln MKX, MKZ and Zephyr and Mercury Milan vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, Ford is recalling certain 2007-2008 Ford Ranger, Edge and Lincoln MKX, 2006-2008 Ford Fusion, Mercury Milan, Lincoln Zephyr and MKZ, 2005-2008 Ford Mustang and 2005-2006 Ford GT vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Interim letters informing owners of the recall and that parts are not yet available began mailing March 1, 2017. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
May 31, 2016
Ford Motor Company (Ford) is recalling certain model year 2007-2011 Ford Ranger vehicles, 2006-2011 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2007-2010 Ford Edge, Lincoln MKX vehicles, 2005-2006 Ford GT vehicles, and 2005-2011 Ford Mustang vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Ford is recalling certain model year 2007-2008 Ford Ranger, Edge and Lincoln MKX vehicles, 2006-2008 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2005-2006 Ford GT vehicles and 2005-2008 Ford Mustang vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Any vehicle not included in "Zone A", or "Zone B" is not included in the safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Ford mailed interim letters informing owners that parts are not yet available on July 15, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4EA18002 · Extended Braking Distance
Opened Apr 18, 2018 · Closed Jan 15, 2021
Status: closed (inferred from source dates) · Service Brakes, Air:antilock:control Unit/module
On April 18, 2018, the Office of Defects Investigation (ODI) opened Engineering Analysis (EA) 18-002 to investigate reports of braking concerns in model year (MY) 2006-12 Ford Fusion and Lincoln MKZ, and MY 2006-11 Mercury Milan vehicles manufactured with Continental Automotive System?s ABS hydraulic control units (HCUs). Complainants report that after an ABS braking event (initiated by slippery or uneven surfaces) the brake pedal moved towards the floor and the vehicle stopping distance increased beyond driver expectations.Inside the HCU are four hydraulic normally closed (NC) valves with zinc-coated moving armatures that control the flow of brake fluid. Unstable brake fluid can degrade over time, allow the brake fluid to gel, and corrosion to form on the armatures. The high-viscosity gelation and corrosion can cause the armatures to become stuck (open). In some cases, braking returns to normal when the armature(s) subsequently become unstuck. The intermittent condition proves difficult to diagnose with complainants reporting having (non-HCU) repairs conducted only to have the condition return.During the investigation, 14 HCUs from complaint vehicles were recovered, including seven from reported crashes. NHTSA?s Vehicle Research and Test Center (VRTC) disassembled the HCUs, removed the four NC valves in each, and confirmed 22 of the 56 NC valves contained stuck armatures. On seven of the 14 HCUs, both front wheel armatures were stuck, on nine of the 14 HCUs two or three armatures were stuck. And 52 of the 56 NC armatures exhibited corrosion of the zinc coating. Forces required to extract stuck armatures from the valve sleeve were measured to range from 1.1 to 18.0 lbs. VRTC also conducted ABS braking tests on a variety of test surfaces that showed HCU failures cause increases in pedal travel and braking distances. Testing also showed that if the driver was able to apply four times the brake pedal force and two times the brake pedal travel, then high-vehicle decelerations could be achieved, however, single or multiple wheel lockups were also occurring.Based on Ford?s response to ODI?s July 20, 2018 information request letter, and complainants' reports to NHTSA, ODI identified a population of vehicles with an elevated level of field failure compared to vehicles produced both before and after.Further evaluation of Ford?s response identified that the brake fluid used to produce these vehicles, a specific formulation of a DOT3 fluid provided by CCI Corporation between February 2006 and July 2009, differed from the brake fluid used in other vehicle populations. ODI used the correlation of fluid specification and elevated field failures to identify a vehicle population exhibiting a defect trend. The complaints, crashes and injuries cited above, and the 14 recovered HCUs involve vehicles from this population.On December 18, 2019, Ford submitted safety recall (19V-904) to remedy HCU failures on the MY 2006-2010 Ford Fusion, Lincoln MKZ, and Mercury Milan vehicles manufactured with the suspect CCI brake fluid formulation. Ford will function test the HCU and replace the DOT 3 brake fluid with an improved DOT 4 brake fluid. If the HCU fails the function test, Ford will install an HCU with a different armature coating (black oxide). HCUs with black oxide coating were fully phased into Ford?s new vehicle production by MY 2016; these HCUs do not appear to be experiencing armature corrosion. ODI notes that the non-recalled EA18-002 subject vehicles, which were manufactured with a different specification brake fluid, did not display an elevated level of field failures like the recalled vehicles.Based on available information, Ford?s rec
PE16017 · Extended Braking Distance
Opened Dec 20, 2016 · Closed May 4, 2018
Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Hydraulic; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
On December 20, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 16-017 to investigate reports of braking concerns in model year 2007 through 2009 Ford Fusion and Mercury Milan vehicles.Complainants report that after an ABS braking event (caused by braking on a slippery or uneven surface) the brake pedal moved towards the floor and the distance in which the vehicle stopped increased beyond what was expected by the driver.The cause of the problem appears to be the Antilock Braking System (ABS) Hydraulic Control Unit (HCU), a component manufactured for Ford by Continental Automotive Systems.Hydraulic control valves within the HCU can experience corrosion and become stuck.In some cases, braking returns to normal when the valve(s) subsequently become unstuck.The intermittent condition proves difficult to diagnose and complainants report having several brake system components replaced only to have the condition return.ODI has identified 544 reports submitted to the agency that relate to this issue in model year 2006-2012 Ford Fusion/MKZ and MY 2006-2011 Mercury Milan, the subject vehicles.Complainants report an increase in pedal travel which in some cases resulted in going past expected stopping points or having to steer to avoid contacting another vehicle; twenty six report a crash with 3 injuries alleged.The Ford reports shown above, which are from PE16-017 and involved the scope discussed above, were similar in content and identified 7 crashes without injury.During PE16-017, ODI was able to recover HCUs from some complaint vehicles, including some from the reported crashes.The recovered HCUs were sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio for evaluation.VRTC was able to confirm stuck valves and corrosion of the zinc coated control valves, and it's testing indicates that HCU failures cause increases in pedal travel that may affect braking distance.According to Ford, newer version HCUs have a different coating on the affected valves that do not currently appear to be experiencing corrosion.In it's response to ODI's information request letter, Ford described analysis of two failed HCUs removed from complainant vehicles.In both cases, a gelatinous material found inside the HCU prevented control valves from properly returning to the closed position after actuation.Ford found that an interaction between the valve coating and brake fluid was the likely source of the gelatinous material.It acknowledged that stuck valves can result in increased pedal travel but maintains the affected brake circuit will develop pressure and respond if the brake pedal is pressed sufficiently.While it has not identified an unreasonable risk to safety due to this issue, Ford states that it continues to investigate the possible causal and contributory factors including additional engineering evaluations and testing.An Engineering Analysis has been opened to assess the scope, frequency, and safety-related consequence of the alleged defect.Based on information received during PE16-017, the scope of the investigation has been increased to include another model, the Lincoln MKZ, and to expand the model years of the subject vehicles.
Additional source detail variants (4)
Service Brakes
On December 20, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 16-017 to investigate reports of braking concerns in model year 2007 through 2009 Ford Fusion and Mercury Milan vehicles.Complainants report that after an ABS braking event (caused by braking on a slippery or uneven surface) the brake pedal moved towards the floor and the distance in which the vehicle stopped increased beyond what was expected by the driver.The cause of the problem appears to be the Antilock Braking System (ABS) Hydraulic Control Unit (HCU), a component manufactured for Ford by Continental Automotive Systems.Hydraulic control valves within the HCU can experience corrosion and become stuck.In some cases, braking returns to normal when the valve(s) subsequently become unstuck.The intermittent condition proves difficult to diagnose and complainants report having several brake system components replaced only to have the condition return.ODI has identified 544 reports submitted to the agency that relate to this issue in model year 2006-2012 Ford Fusion/MKZ and MY 2006-2011 Mercury Milan, the subject vehicles.Complainants report an increase in pedal travel which in some cases resulted in going past expected stopping points or having to steer to avoid contacting another vehicle; twenty six report a crash with 3 injuries alleged.The Ford reports shown above, which are from PE16-017 and involved the scope discussed above, were similar in content and identified 7 crashes without injury.During PE16-017, ODI was able to recover HCUs from some complaint vehicles, including some from the reported crashes.The recovered HCUs were sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio for evaluation.VRTC was able to confirm stuck valves and corrosion of the zinc coated control valves, and it's testing indicates that HCU failures cause increases in pedal travel that may affect braking distance.According to Ford, newer version HCUs have a different coating on the affected valves that do not currently appear to be experiencing corrosion.In it's response to ODI's information request letter, Ford described analysis of two failed HCUs removed from complainant vehicles.In both cases, a gelatinous material found inside the HCU prevented control valves from properly returning to the closed position after actuation.Ford found that an interaction between the valve coating and brake fluid was the likely source of the gelatinous material.It acknowledged that stuck valves can result in increased pedal travel but maintains the affected brake circuit will develop pressure and respond if the brake pedal is pressed sufficiently.While it has not identified an unreasonable risk to safety due to this issue, Ford states that it continues to investigate the possible causal and contributory factors including additional engineering evaluations and testing.An Engineering Analysis has been opened to assess the scope, frequency, and safety-related consequence of the alleged defect.Based on information received during PE16-017, the scope of the investigation has been increased to include another model, the Lincoln MKZ, and to expand the model years of the subject vehicles.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
On December 20, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 16-017 to investigate reports of braking concerns in model year 2007 through 2009 Ford Fusion and Mercury Milan vehicles.Complainants report that after an ABS braking event (caused by braking on a slippery or uneven surface) the brake pedal moved towards the floor and the distance in which the vehicle stopped increased beyond what was expected by the driver.The cause of the problem appears to be the Antilock Braking System (ABS) Hydraulic Control Unit (HCU), a component manufactured for Ford by Continental Automotive Systems.Hydraulic control valves within the HCU can experience corrosion and become stuck.In some cases, braking returns to normal when the valve(s) subsequently become unstuck.The intermittent condition proves difficult to diagnose and complainants report having several brake system components replaced only to have the condition return.ODI has identified 544 reports submitted to the agency that relate to this issue in model year 2006-2012 Ford Fusion/MKZ and MY 2006-2011 Mercury Milan, the subject vehicles.Complainants report an increase in pedal travel which in some cases resulted in going past expected stopping points or having to steer to avoid contacting another vehicle; twenty six report a crash with 3 injuries alleged.The Ford reports shown above, which are from PE16-017 and involved the scope discussed above, were similar in content and identified 7 crashes without injury.During PE16-017, ODI was able to recover HCUs from some complaint vehicles, including some from the reported crashes.The recovered HCUs were sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio for evaluation.VRTC was able to confirm stuck valves and corrosion of the zinc coated control valves, and it's testing indicates that HCU failures cause increases in pedal travel that may affect braking distance.According to Ford, newer version HCUs have a different coating on the affected valves that do not currently appear to be experiencing corrosion.In it's response to ODI's information request letter, Ford described analysis of two failed HCUs removed from complainant vehicles.In both cases, a gelatinous material found inside the HCU prevented control valves from properly returning to the closed position after actuation.Ford found that an interaction between the valve coating and brake fluid was the likely source of the gelatinous material.It acknowledged that stuck valves can result in increased pedal travel but maintains the affected brake circuit will develop pressure and respond if the brake pedal is pressed sufficiently.While it has not identified an unreasonable risk to safety due to this issue, Ford states that it continues to investigate the possible causal and contributory factors including additional engineering evaluations and testing.An Engineering Analysis has been opened to assess the scope, frequency, and safety-related consequence of the alleged defect.Based on information received during PE16-017, the scope of the investigation has been increased to include another model, the Lincoln MKZ, and to expand the model years of the subject vehicles.
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip
On December 20, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 16-017 to investigate reports of braking concerns in model year 2007 through 2009 Ford Fusion and Mercury Milan vehicles.Complainants report that after an ABS braking event (caused by braking on a slippery or uneven surface) the brake pedal moved towards the floor and the distance in which the vehicle stopped increased beyond what was expected by the driver.The cause of the problem appears to be the Antilock Braking System (ABS) Hydraulic Control Unit (HCU), a component manufactured for Ford by Continental Automotive Systems.Hydraulic control valves within the HCU can experience corrosion and become stuck.In some cases, braking returns to normal when the valve(s) subsequently become unstuck.The intermittent condition proves difficult to diagnose and complainants report having several brake system components replaced only to have the condition return.ODI has identified 544 reports submitted to the agency that relate to this issue in model year 2006-2012 Ford Fusion/MKZ and MY 2006-2011 Mercury Milan, the subject vehicles.Complainants report an increase in pedal travel which in some cases resulted in going past expected stopping points or having to steer to avoid contacting another vehicle; twenty six report a crash with 3 injuries alleged.The Ford reports shown above, which are from PE16-017 and involved the scope discussed above, were similar in content and identified 7 crashes without injury.During PE16-017, ODI was able to recover HCUs from some complaint vehicles, including some from the reported crashes.The recovered HCUs were sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio for evaluation.VRTC was able to confirm stuck valves and corrosion of the zinc coated control valves, and it's testing indicates that HCU failures cause increases in pedal travel that may affect braking distance.According to Ford, newer version HCUs have a different coating on the affected valves that do not currently appear to be experiencing corrosion.In it's response to ODI's information request letter, Ford described analysis of two failed HCUs removed from complainant vehicles.In both cases, a gelatinous material found inside the HCU prevented control valves from properly returning to the closed position after actuation.Ford found that an interaction between the valve coating and brake fluid was the likely source of the gelatinous material.It acknowledged that stuck valves can result in increased pedal travel but maintains the affected brake circuit will develop pressure and respond if the brake pedal is pressed sufficiently.While it has not identified an unreasonable risk to safety due to this issue, Ford states that it continues to investigate the possible causal and contributory factors including additional engineering evaluations and testing.An Engineering Analysis has been opened to assess the scope, frequency, and safety-related consequence of the alleged defect.Based on information received during PE16-017, the scope of the investigation has been increased to include another model, the Lincoln MKZ, and to expand the model years of the subject vehicles.
Service Brakes, Hydraulic
On December 20, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 16-017 to investigate reports of braking concerns in model year 2007 through 2009 Ford Fusion and Mercury Milan vehicles.Complainants report that after an ABS braking event (caused by braking on a slippery or uneven surface) the brake pedal moved towards the floor and the distance in which the vehicle stopped increased beyond what was expected by the driver.The cause of the problem appears to be the Antilock Braking System (ABS) Hydraulic Control Unit (HCU), a component manufactured for Ford by Continental Automotive Systems.Hydraulic control valves within the HCU can experience corrosion and become stuck.In some cases, braking returns to normal when the valve(s) subsequently become unstuck.The intermittent condition proves difficult to diagnose and complainants report having several brake system components replaced only to have the condition return.ODI has identified 544 reports submitted to the agency that relate to this issue in model year 2006-2012 Ford Fusion/MKZ and MY 2006-2011 Mercury Milan, the subject vehicles.Complainants report an increase in pedal travel which in some cases resulted in going past expected stopping points or having to steer to avoid contacting another vehicle; twenty six report a crash with 3 injuries alleged.The Ford reports shown above, which are from PE16-017 and involved the scope discussed above, were similar in content and identified 7 crashes without injury.During PE16-017, ODI was able to recover HCUs from some complaint vehicles, including some from the reported crashes.The recovered HCUs were sent to NHTSA's Vehicle Research and Test Center (VRTC) in East Liberty, Ohio for evaluation.VRTC was able to confirm stuck valves and corrosion of the zinc coated control valves, and it's testing indicates that HCU failures cause increases in pedal travel that may affect braking distance.According to Ford, newer version HCUs have a different coating on the affected valves that do not currently appear to be experiencing corrosion.In it's response to ODI's information request letter, Ford described analysis of two failed HCUs removed from complainant vehicles.In both cases, a gelatinous material found inside the HCU prevented control valves from properly returning to the closed position after actuation.Ford found that an interaction between the valve coating and brake fluid was the likely source of the gelatinous material.It acknowledged that stuck valves can result in increased pedal travel but maintains the affected brake circuit will develop pressure and respond if the brake pedal is pressed sufficiently.While it has not identified an unreasonable risk to safety due to this issue, Ford states that it continues to investigate the possible causal and contributory factors including additional engineering evaluations and testing.An Engineering Analysis has been opened to assess the scope, frequency, and safety-related consequence of the alleged defect.Based on information received during PE16-017, the scope of the investigation has been increased to include another model, the Lincoln MKZ, and to expand the model years of the subject vehicles.
EA12009 · Floor Mat Interference With Accelerator
Opened Dec 12, 2012 · Closed Jun 12, 2014
Status: closed (inferred from source dates) · Vehicle Speed Control; Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Additional source detail variants (2)
Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Vehicle Speed Control
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
PE10019 · Accel Pedal Interference - Acc Floormat
Opened May 28, 2010 · Closed Jan 11, 2013
Status: closed (inferred from source dates) · Vehicle Speed Control:accelerator Pedal
Unsecured mats may interfere with accelerator pedal return to idle. A heel blocker in the floor pan provides a platform that may lift an unsecured mat into contact with the pedal. Ford introduced new pedals as a running change early in model year (MY) 2010 vehicles. Analysis of complaints received by ODI and Ford show elevated rates of pedal entrapment incidents in MY 2008 through early 2010 production vehicles. Incidents typically occur following hard pedal applications to pass slower traffic or when merging into faster traffic. Drivers allege continued high engine power after releasing the accelerator pedal and difficulty braking, including reports that the incident was controlled by shifting to neutral or turning the engine off. Drivers and service technicians reference observing evidence of mat interference or note unsecured Ford or aftermarket all weather floor mats in post-incident inspections.Based on information gathered during the Preliminary Evaluation the population being investigated has been narrowed to model years 2008 to 2010.This investigation has been upgraded to an engineering analysis on MY 2008 through early-2010 vehicles (produced through September 2009) to further assess the scope, frequency and safety consequences of the alleged defect.The VOQs associated with the opening of this Engineering Analysis are: 10479693, 10415911, 10379562, 10372674, 10345830, 10342572, 10339330, 10335336, 10334211, 10332233, 10331160, 10329659, 10327597, 10320011, 10232027, 10214131
Illustration