NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
508 reports82,000 miles · Jul 6, 2016
Power Train
DRIVING FROM DALLAS TO AUSTIN AND WITH ABOUT 60 MILES LEFT, THE YELLOW WRENCH WARNING LIGHT CAME ON IN THE CAR. I PULLED OVER AS SOON AS I COULD TO SEE WHAT THE LIGHT INDICATED. THE MANUAL SAID IT WAS A THROTTLE CONTROL POWER TRAIN MALFUNCTION. I TURNED OFF THE CAR AND WAITED A BIT. WHEN I TURNED THE CAR ON, THE LIGHT DID NO…
Read full complaint
DRIVING FROM DALLAS TO AUSTIN AND WITH ABOUT 60 MILES LEFT, THE YELLOW WRENCH WARNING LIGHT CAME ON IN THE CAR. I PULLED OVER AS SOON AS I COULD TO SEE WHAT THE LIGHT INDICATED. THE MANUAL SAID IT WAS A THROTTLE CONTROL POWER TRAIN MALFUNCTION. I TURNED OFF THE CAR AND WAITED A BIT. WHEN I TURNED THE CAR ON, THE LIGHT DID NOT COME ON AGAIN, BUT I AM CONCERNED THE CAR WILL BECOME UN-DRIVABLE. I SEE THAT THIS IS A COMMON PROBLEM... TOO COMMON. IS THERE A RECALL YET?
NHTSA ODI #10882838
53,600 miles · Jul 3, 2016
Air Bags
"PASS AIRBAG OFF" LIGHT COMES ON RANDOMLY WHEN PASSENGER IS SEATED REGARDLESS OF CAR MOVEMENT, SPEED, OR ROAD CONDITIONS. ATTACHED IS A RECENT INCIDENT.
NHTSA ODI #10882349
114,459 miles · Jun 30, 2016
Fuel/propulsion System
THROTTLE BODY FAILED. WHILE IN MOTION ON DIVIDED 45 MPH ROAD, CAR WOULD NOT ACCELERATE. MAX SPEED 45 GOING DOWN HILL. FOUND THROTTLE BODY FAILED.
NHTSA ODI #10881895
70,000 miles · Jun 12, 2016
Electrical SystemFuel/propulsion SystemVehicle Speed Control
I WAS DRIVING THE CAR ABOUT 60 MPH ON THE HIGHWAY WHEN I SAW A BIG RED TRIANGLE ON THE DISPLAY SAYING "PULL OVER AND STOP SAFELY" AND THE CAR SLOWED DOWN DRAMATICALLY. I DID THAT AND TURNED OFF THE ENGINE. I RESTARTED THE CAR. THIS OCCURRED 8 MORE TIMES BEFORE I GOT HOME (15 MILES LATER). WHEN I GOT HOME, I NOTICED THAT THE …
Read full complaint
I WAS DRIVING THE CAR ABOUT 60 MPH ON THE HIGHWAY WHEN I SAW A BIG RED TRIANGLE ON THE DISPLAY SAYING "PULL OVER AND STOP SAFELY" AND THE CAR SLOWED DOWN DRAMATICALLY. I DID THAT AND TURNED OFF THE ENGINE. I RESTARTED THE CAR. THIS OCCURRED 8 MORE TIMES BEFORE I GOT HOME (15 MILES LATER). WHEN I GOT HOME, I NOTICED THAT THE CAR'S FAN WAS RUNNING VERY HIGH FOR SEVERAL MINUTES. IT FINALLY STOPPED.
NHTSA ODI #10873748
75,250 miles · Jun 10, 2016
Power TrainVehicle Speed Control
MY DAUGHTER HAS HER LEARNER'S PERMIT AND WAS DRIVING MY FORD FUSION HYBRID ON A 45 MPH STREET. THE WRENCH LIGHT CAME ON AND THE CAR WOULD NOT ACCELERATE AS SHE WAS DRIVING UP A HILLY PART OF THE STREET. CARS BEGAN HONKING AND PASSING AND MY DAUGHTER BECAME EXTREMELY NERVOUS. THANKFULLY, WE WERE NOT INVOLVED IN A CAR ACCIDENT …
Read full complaint
MY DAUGHTER HAS HER LEARNER'S PERMIT AND WAS DRIVING MY FORD FUSION HYBRID ON A 45 MPH STREET. THE WRENCH LIGHT CAME ON AND THE CAR WOULD NOT ACCELERATE AS SHE WAS DRIVING UP A HILLY PART OF THE STREET. CARS BEGAN HONKING AND PASSING AND MY DAUGHTER BECAME EXTREMELY NERVOUS. THANKFULLY, WE WERE NOT INVOLVED IN A CAR ACCIDENT BUT SHE WAS QUITE SHAKEN BY THE INCIDENT. I TOOK THE VEHICLE TO THE FORD DEALERSHIP TO HAVE IT REPAIRED AND WAS ADVISED THIS WAS NOT A RECALL EVEN THOUGH THERE ARE SEVERAL THOUSAND COMPLAINTS AND ISSUES. I HAD TO HAVE THE THROTTLE BODY REPLACED WHICH IS APPARENTLY A DEFECTIVE PART. I DON'T UNDERSTAND WHY THERE ISN'T A RECALL FOR THIS DEFECT. I UNDERSTAND THE NHTSA CONSIDERS SAFETY A HUGE FACTOR WHEN RECALLING PARTS. HOWEVER, THE PART IS CLEARLY DEFECTIVE AND HAS COST CONSUMERS GREATLY. PLEASE RECONSIDER RECALLING OR AT LEAST SUBSIDIZING THE PAYMENT FOR THOSE AFFECTED BY THIS DEFECTIVE PART.
NHTSA ODI #10873569
57,983 miles · Jun 10, 2016
Engine
ON JUNE 7, 2016, MY WIFE WAS DRIVING OUR 2010 FORD FUSION HYBRID ON A MAJOR HIGHWAY WHEN THE WRENCH LIGHT CAME UP AND THE CAR LOST POWER AND WOULD NOT ACCELERATE. THE CAR WAS TOWED TO NORTH CENTRAL FORD WHERE IT WAS REPAIRED BY REPLACING THE ELECTRONIC THROTTLE BODY AND REPROGRAMMING THE PCM. THE CAR HAS LESS THAN 58,000 MILES…
Read full complaint
ON JUNE 7, 2016, MY WIFE WAS DRIVING OUR 2010 FORD FUSION HYBRID ON A MAJOR HIGHWAY WHEN THE WRENCH LIGHT CAME UP AND THE CAR LOST POWER AND WOULD NOT ACCELERATE. THE CAR WAS TOWED TO NORTH CENTRAL FORD WHERE IT WAS REPAIRED BY REPLACING THE ELECTRONIC THROTTLE BODY AND REPROGRAMMING THE PCM. THE CAR HAS LESS THAN 58,000 MILES ON THE ODOMETER. WHY DOES FORD EXCLUDE HYBRIDS FROM THIS KNOWN PROBLEM AND ITS ASSOCIATED CUSTOMER SATISFACTION PROGRAM 13N03, POPULATION OF HYBRIDS TOO SMALL? IT MAKES NO SENSE. THE PART, FAILURE SYMPTOMS AND FIX ARE THE SAME AS THOSE IN THE FORD CARS COVERED BY 13N03. AND WHY DID THE NHTSA ALLOW FORD NOT TO HAVE A RECALL FOR THE DEFECTIVE PART, POLITICS? CANNOT UNDERSTAND WHY THIS IS NOT A SAFETY ISSUE.
NHTSA ODI #10873560
125,000 miles · Jun 6, 2016
Suspension
THE DRIVERS SIDE FRONT COIL SPRING SNAPPED. FORTUNATELY THIS HAPPENED WHILE THE CAR WAS PARKED. THERE IS A SAFETY RECALL FOR THIS DEFECT BUT MY VEHICLE IS NOT COVERED UNDER THAT RECALL. FORD NEEDS TO STEP UP AND EXPAND THE RECALL.
NHTSA ODI #10872666
64,093 miles · May 26, 2016
Service Brakes
I WAS DRIVING TO WORK, WHICH DOES NOT REQUIRE FOR ME TO TAKE THE HIGHWAY, AND AT A FOUR-WAY STOP I TRIED TO STOP MY 2010 FORD FUSION HYBRID CAR BY USING THE BRAKE PEDAL AND IT DID NOT STOP THE CAR AT ALL, BUT ITS PUMP-ACTION WAS STILL THERE. LUCKILY THERE WERE NO CARS AT THE FOUR-WAY STOP. IF THERE WERE CARS THERE, I COULD HAVE…
Read full complaint
I WAS DRIVING TO WORK, WHICH DOES NOT REQUIRE FOR ME TO TAKE THE HIGHWAY, AND AT A FOUR-WAY STOP I TRIED TO STOP MY 2010 FORD FUSION HYBRID CAR BY USING THE BRAKE PEDAL AND IT DID NOT STOP THE CAR AT ALL, BUT ITS PUMP-ACTION WAS STILL THERE. LUCKILY THERE WERE NO CARS AT THE FOUR-WAY STOP. IF THERE WERE CARS THERE, I COULD HAVE GOTTEN INTO A CAR ACCIDENT, EVEN WORSE IF I WAS ON THE HIGHWAY. WHEN THE BRAKE ISSUE OCCURRED, THE FOLLOWING TWO SYSTEM ERROR CODES APPEARED ON MY DASHBOARD: 1.) "(!) BRAKE CHECK BRAKE SYSTEM" AND (2) "SERVICE ADVANCETRAC". AT THE SAME TIME THAT THESE TWO SYSTEM ERROR CODES APPEARED, THERE WERE FIVE WARNING LIGHTS THAT APPEARED: 1.) ADVANCETRAC/TRACTION CONTROL OFF LIGHT (AKA ORANGE-YELLOW CAR W/ TIRE MARKS OFF) 2.) ADVANCETRAC/TRACTION CONTROL (AKA ORANGE-YELLOW CAR W/ TIRE MARKS SYMBOL) 3.) BRAKE SYSTEM WARNING LIGHT (AKA RED !(P) BRAKE) 4.) ANTI-LOCK BRAKE SYSTEM (AKA "ABS" SYMBOL) WARNING LIGHT 5.) ON THE UPPER LEFT-HAND CORNER TO THE LEFT OF THE SYSTEM ERROR CODE "(!) BRAKE CHECK BRAKE SYSTEM" A LITTLE (!) BRAKE SYMBOL APPEARED. I HAVE A PICTURE OF ALL OF THESE SYSTEM ERROR CODES AND LIGHTS. SO, THEN I USED THE EMERGENCY BRAKE HANDLE STICK TO STOP THE CAR AND THAT HELPED ONLY TO SLOW THE CAR DOWN BY 20%, BUT NOT ENOUGH TO STOP THE CAR. I LEFT THE EMERGENCY BRAKE ON AND DID NOT USE THE ACCELERATOR PEDAL TO SLOW DOWN THE CAR. THE CAR SLOWED DOWN TO A SLOW STOP AFTER 1-2 MINUTES AFTER DRIVING OVER SOME SPEED BUMPS DRIVING AT 30-35 MPH. WHEN IT STOPPED, I RESTARTED THE CAR TO SEE IF THAT WOULD FIX THE ISSUE AND IT DID NOT. SO I PRESSED THE ACCELERATOR PEDAL VERY LIGHTLY WITHOUT USING THE EMERGENCY BRAKE AND GOT TO A SPEED OF LESS THAN 10 MPH TO GET TO WORK BECAUSE I WAS ALMOST THERE. WHEN I SLOWLY DRIFTED INTO MY WORK'S PARKING LOT, I IMMEDIATELY USED THE EMERGENCY BRAKE AGAIN TO GET THE CAR TO STOP.
NHTSA ODI #10871006
65,000 miles · May 20, 2016
EnginePower TrainVehicle Speed Control
WHEN OPERATING THE CAR ON THE FREEWAY, THE CAR SUDDENLY LOST POWER AND ONLY COULD ACHIEVE 45 MPH IN SPITE OF THE ACCELERATOR BEING FLOORED. WHEN EVENTUALLY STOPPED, THE ENGINE WOULD SURGE AND SHUDDER PERIODICALLY. THE CHECK ENGINE LIGHT CAME ON. PULLING THE TROUBLE CODE REVEALED P2112 WHICH IS A THROTTLE BODY ERROR.
NHTSA ODI #10870008
39,155 miles · May 12, 2016
Latches/locks/linkagesSuspension
2010 FORD FUSION HYBRID. CONSUMER WRITES IN REGARDS TO PART OF THE INSIDE DOOR HANDLE SNAPPED OFF. *SMD THE CONSUMER STATED HE HAD TO EXIT THE VEHICLE, WITHOUT THE USE OF THE INDOOR HANDLE. THE DOOR HANDLE WAS MADE OF CHEAP, WEAK, POORLY DESIGNED MATERIAL. ALSO, AT 39,155 MILES, ONE OF THE FRONT WHEEL BEARINGS HAD TO REPLACE…
Read full complaint
2010 FORD FUSION HYBRID. CONSUMER WRITES IN REGARDS TO PART OF THE INSIDE DOOR HANDLE SNAPPED OFF. *SMD THE CONSUMER STATED HE HAD TO EXIT THE VEHICLE, WITHOUT THE USE OF THE INDOOR HANDLE. THE DOOR HANDLE WAS MADE OF CHEAP, WEAK, POORLY DESIGNED MATERIAL. ALSO, AT 39,155 MILES, ONE OF THE FRONT WHEEL BEARINGS HAD TO REPLACED. *JB
NHTSA ODI #10862868
NHTSA investigations
6DP26004 · Anti-lock Brake System (abs) Malfunction Indicator Lamp (mil) Illuminated
Opened Apr 9, 2026 · No close date supplied
Status: open (inferred from source dates) · Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module
The Office of Defects Investigation (ODI) received a petition on December 22, 2025, requesting a defect investigation into the hydraulic control unit (HCU) for the Anti-lock Braking System (ABS) on the MY 2010 Ford Fusion Hybrid. The petition alleges that an illuminated ABS MIL is associated with a failure of the ABS HCU, resulting in ABS malfunction, loss of traction and electronic stability control functions, and reduced braking performance, particularly on slippery road surfaces. A defect petition has been opened to evaluate the issue and determine whether to grant or deny the petition.The petition can be reviewed at NHTSA.gov under ODI number 11647929.
DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
EA17004 · Power Steering Failure
Opened Nov 20, 2017 · Closed Feb 9, 2024
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:rack And Pinion; Steering:rack And Pinion:rack
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (4)
Steering:electric Power Assist System
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering:rack And Pinion
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering:rack And Pinion:rack
On September 28, 2016, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE16-011) to investigate claims of power steering assist loss on model year (MY) 2010 Ford Fusion vehicles. During the PE, ODI received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at various speeds with no warning. Ford Motor Company (Ford) provided 1,851 unique reports and 1,720 warranty claims related to the alleged problem. It should be noted that as the result of investigation PE14-030, Ford conducted a safety recall (15V-340) ofMY 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist. On November 20, 2017, PE16-011 was upgraded to this Engineering Analysis (EA17-004) to further assess the scope, frequency, and consequence of this failure. This was based on an analysis of the subject vehicle complaint data that had indicated an increased likelihood of failure as the vehicles age. At the time, the rate of occurrence of this failure was comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030. During the EA, ODI’s analysis of the alleged defect in the subject vehicles identified the following: testing showed minor steering effort changes between “assist” and “no assist”, no root cause identified, a declining failure trend, the ramp-down or reduced assist provided when a DTC is set, a lower failure rate than the recalled Fusion vehicles, and the high age of the vehicles. A safety-related defect trend has not been identified. Accordingly, this Engineering Analysis is closed. See the attached Engineering Analysis Closing Report for details. The closing of this investigation does not constitute a finding by NHTSA that a safety defect does not exist, and ODI will take further actions if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE16011 · Power Steering Failure
Opened Sep 28, 2016 · Closed Dec 25, 2017
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System
On September 28th, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-011 to investigate claims of power steering assist loss on model year 2010 Ford Fusion vehicles.ODI has received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at speed with no warning.During the PE16-011 investigation, Ford Motor Company (Ford) provided 1851 unique reports and 1720 warranty claims related to the alleged problem.As the result of investigation PE14-030, Ford previously conducted a recall (15V-340) of the 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist.An analysis of the subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.The rate of occurrence of this failure is comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030.Therefore, the Preliminary Evaluation (PE16-011) has been upgraded to an Engineering Analysis to further assess the scope, frequency and consequence of this failure. ODI reports cited above can be reviewed at https://www.nhtsa.gov/recalls#vehicle under the identification (NHTSA ID) numbers found in the attached list.
Additional source detail variants (2)
Steering:electric Power Assist System
On September 28th, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-011 to investigate claims of power steering assist loss on model year 2010 Ford Fusion vehicles.ODI has received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at speed with no warning.During the PE16-011 investigation, Ford Motor Company (Ford) provided 1851 unique reports and 1720 warranty claims related to the alleged problem.As the result of investigation PE14-030, Ford previously conducted a recall (15V-340) of the 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist.An analysis of the subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.The rate of occurrence of this failure is comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030.Therefore, the Preliminary Evaluation (PE16-011) has been upgraded to an Engineering Analysis to further assess the scope, frequency and consequence of this failure. ODI reports cited above can be reviewed at https://www.nhtsa.gov/recalls#vehicle under the identification (NHTSA ID) numbers found in the attached list.
Steering
On September 28th, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-011 to investigate claims of power steering assist loss on model year 2010 Ford Fusion vehicles.ODI has received 718 unique claims related to the alleged problem with 598 reports indicating the power steering assist failed while driving at speed with no warning.During the PE16-011 investigation, Ford Motor Company (Ford) provided 1851 unique reports and 1720 warranty claims related to the alleged problem.As the result of investigation PE14-030, Ford previously conducted a recall (15V-340) of the 2011-2012 Ford Fusion and other vehicles using the same electric power assist steering unit to rectify incidents of loss of power steering assist.An analysis of the subject vehicle complaint data indicates an increased likelihood of failure as the vehicles age.The rate of occurrence of this failure is comparable to previous investigations involving loss of power steering assist including the previously mentioned PE14-030.Therefore, the Preliminary Evaluation (PE16-011) has been upgraded to an Engineering Analysis to further assess the scope, frequency and consequence of this failure. ODI reports cited above can be reviewed at https://www.nhtsa.gov/recalls#vehicle under the identification (NHTSA ID) numbers found in the attached list.
PE14030 · Electric Power Steering Failure
Opened Oct 2, 2014 · Closed Sep 10, 2015
Status: closed (inferred from source dates) · Steering:electric Power Assist System
The Office of Defects Investigation (ODI) opened a preliminary evaluation to investigate complaints of the loss of power steering while driving. The subject vehicles are equipped with a rack mounted Electric Power Assisted Steering (EPAS) unit.Some of the complaints alleged that the steering assist failed and resulted in increased steering efforts that contributed to a loss of control and in some cases a crash.The EPAS system was manufactured by TRW Automotive for Ford and was designated as Generation I.These units were first produced and put into vehicle production in July 2008 beginning with the model year (MY) 2010 Ford Fusion and Mercury Milan.The system is comprised of a mechanical steering rack-and-pinion gear with torque sensor, electric assist motor, motor position sensor and a power steering control module (PSCM). The PSCM is self-monitoring and designed to detect faults within the system and can store diagnostic trouble codes (DTCs) if a problem is detected.There are 29 potential DTCs the system can detect.Many of these allow the system to go into reduced-assist steering mode by using the default vehicle speed signal should the live speed signal be lost, if voltage to EPAS system falls below 10.7 or goes above 17 volts, the temperature at the PSCM goes above 105C (221F), or if high friction is detected.Some DTCs will cause the system to go into manual steering mode (no assist). On July 1, 2015, Ford filed a Defect Information Report (DIR) identifying a safety related defect in TRW GEN I EPAS systems installed in some of the subject vehicles (NHTSA Recall 15V-340, Ford No. 15S18).The DIR indicated that intermittent electrical connections caused by quality issues associated with conformal coat contamination and ribbon cable pin misalignment within the steering gear motor may lead to a loss of the motor position sensor signal, resulting in a sudden loss of power assist while driving.The recall covers approximately 393,623 vehicles built from September 2010 through February 2012:2011-12 Fusion built SEP 2010 - FEB 2012; 2011-12 Lincoln MKZ built SEP 2010 - FEB 2012; 2011 Milan built SEP 2010 - DEC 2010; 2011-13 Taurus built SEP 2010 - FEB 2012; 2011-13 Flex with 3.5L GTDI engine built SEP 2010 - FEB 2012; and 2011-13 MKS, MKT with 3.5L GTDI engine built SEP 2010 - FEB 2012.The repair consists of updating the PSCM software to prevent a loss of steering assist while driving. The revised software will provide audible and visual warnings to the driver. If one or more of the following DTCs are stored, C1B00-62, C200B-2F, C200B-61, C200B-62, C200C-2F, C200D-49, U0300-00, U2011-49, U2011-61, U3000-46, U3000-49, U3000-61, U3000-72, U3000-96, P07AE-09, the dealer will replace the EPAS system at no charge to the owner.ODI's analysis of failure data for this PE identified a total of 2,584 complaints to ODI and Ford and 9,967 Ford warranty claims related to the alleged defect.The recalled vehicles account for 1,634 of the complaints and 7,311 of the warranty claims.ODI's analysis identified 40 complaints alleging crashes that may be related to loss of steering assist while driving, 20 of which involved vehicles included in Ford's recall.The information available for the alleged crashes were not sufficient to assess specific causes of the incidents or to verify EPAS malfunctions in each case.Most of the crashes were low-speed impacts with curbs or roadside objects resulting in wheel or minor body damage.None of the injury claims indicated medical attention was required.In addition, statistical modeling of the failure data by NHTSA's National Center for Statistics and Analysis projected 10-year failur
EA12009 · Floor Mat Interference With Accelerator
Opened Dec 12, 2012 · Closed Jun 12, 2014
Status: closed (inferred from source dates) · Vehicle Speed Control; Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Additional source detail variants (2)
Vehicle Speed Control:accelerator Pedal
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Vehicle Speed Control
On May 27, 2014, Ford Motor Company submitted recall 14E-028 (Ford recall #14S07) to correct a safety-related problem with certain driver's side Ford optional all-weather floor mats sold for use in model year 2006 through 2011 model year Ford Fusion, Mercury Milan, Lincoln Zephyr, and Lincoln MKZ vehicles built at Hermosillo Assembly Plant (HAP) from November 9, 2007, to October 31 ,2010.NHTSA testing determined that the original accessory all-weather mat with a single retention clip (Figure 1), may interfere with accelerator pedal return to idle with the mat retained by the clip and rotated clockwise.Both the single- and double-clip (Figure 2) all-weather floor mats may interfere with the accelerator pedal return to idle when the mats are not secured by the retention clip(s).Testing showed that this can occur if the mats are moved forward from the clipped position approximately two inches into a position in which the rear edge of the mats will abut the retention clip(s) when installed singly and align with the clip(s) when stacked on another floor mat.The pedal interference incidents reviewed by the Office of Defects Investigation (ODI) include 1 crash and 9 incidents with allegations of brake friction materials smoking and/or requiring repair for heat related damage.The crash incident occurred after the parking brake was applied at speed, resulting in loss-of-control vehicle yaw event caused by lock-up of the rear tires.The spin-out resulted in a side impact collision with an oncoming vehicle in an opposing lane of traffic. For the 29 incidents with sufficient information available to make an assessment; 23 (79%) were controlled by the driver either shifting to neutral, turning the engine off, or both; 4 (14%) were ended by the driver either kicking the pedal free (2) or pulling the mat away from the pedal (2); and 2 (7%) were ended by the pedal freeing itself from the mat with no apparent driver action.None of the drivers who reacted to the incident by shifting to neutral or turning the engine off reported any difficulties with either action.The subject mats were sold by Ford and Lincoln dealers directly to customers as an optional accessory equipment item or, beginning in November 2007, the mats were also available as a factory installed accessory if ordered with a new vehicle.Ford estimates that approximately 82,579 affected driver's side all weather floor mats were sold worldwide; either over the counter through Ford dealerships or as original equipment.Owners that purchased the subject all-weather floor mats as a factory installed accessory with their new vehicle will be notified to return their all weather floor mats to their Ford or Lincoln Dealership in exchange for replacement mats.Owners of all other potentially affected vehicles will be notified that, if they have an affected Ford driver's side all weather floor mat, they should return their mats to the dealership in exchange for replacement mats.The VOQs associated with the closing of this investigation are: 10327597, 10332233, 10334211, 10335336, 10339330, 10348772 (and duplicate 10342572), 10372674, 10379562, 10415911, 10426255, 10434107, 10521053, 10554966.This investigation is hereby closed.
Illustration