NHTSA owner reports · September 18, 2026 snapshot.
Fuel System, Gasoline complaints
61 reportsClear category filter35,000 miles · Nov 30, 2022
Fuel System, Gasoline
The contact owns a 2017 Ford Focus. The contact stated that while driving at various speeds, the check engine warning light illuminated, and the vehicle would not properly accelerate while depressing the accelerator pedal. Additionally, after refueling, the vehicle would not immediately start. The vehicle was taken to the local …
Read full complaint
The contact owns a 2017 Ford Focus. The contact stated that while driving at various speeds, the check engine warning light illuminated, and the vehicle would not properly accelerate while depressing the accelerator pedal. Additionally, after refueling, the vehicle would not immediately start. The vehicle was taken to the local mechanic and the local dealer who diagnosed that the purge valve was faulty, causing the fuel tank to become deformed. The vehicle was not yet repaired. The manufacturer was notified of the failure, but no assistance was offered. The contact was informed that the VIN was not included in NHTSA Campaign Number: 19V515000 (Fuel System, Gasoline). The failure mileage was 35,000.
NHTSA ODI #11495450
45,000 miles · Oct 19, 2022
Fuel System, Gasoline
The contact owns a 2017 Ford Focus. The contact stated that after refueling the vehicle, the vehicle would not immediately start-up. The contact stated that several attempts were needed to restart the vehicle. The vehicle would idle rough after start-up. The contact would depress the accelerator while the vehicle was in park(P) …
Read full complaint
The contact owns a 2017 Ford Focus. The contact stated that after refueling the vehicle, the vehicle would not immediately start-up. The contact stated that several attempts were needed to restart the vehicle. The vehicle would idle rough after start-up. The contact would depress the accelerator while the vehicle was in park(P) and rev the engine to 3,000 RPM before the vehicle would operate normally. The contact stated no warning lights were illuminated. The contact stated that the failure to start up after fueling was intermittent; however, the failure occurred more frequently. The contact stated that while starting the vehicle he had to depress the accelerator pedal down for a minute or two and take several attempts to start the vehicle. The contact had taken the vehicle to a local dealer who diagnosed that the canister purge valve needed to be replaced. The vehicle had not been repaired. The contact researched online and related the failure to NHTSA Campaign Number: 19V515000 (Fuel System, Gasoline). The manufacturer had been informed of the failure. The failure mileage was approximately 45,000.
NHTSA ODI #11489972
96,000 miles · Sep 27, 2022
Fuel System, Gasoline
The contact owns a 2017 Ford Focus. The contact stated that after refueling the vehicle and attempting to restart the vehicle, the RPM was fluctuating and the vehicle then lost motive power. The check engine warning light illuminated. The contact stated that after a few attempts she was able to restart vehicle. The vehicle was t…
Read full complaint
The contact owns a 2017 Ford Focus. The contact stated that after refueling the vehicle and attempting to restart the vehicle, the RPM was fluctuating and the vehicle then lost motive power. The check engine warning light illuminated. The contact stated that after a few attempts she was able to restart vehicle. The vehicle was then taken to an independent mechanic; however, the contact was not provided with a diagnosis and the vehicle was not repaired. The failure continued after refueling and the contact stated that the vehicle would stall and lose motive power after coming to a complete stop at a red light or at a stop sign. The vehicle was then taken to another independent mechanic where the failure code P144A for the EVAP system was retrieved. The contact referenced NHTSA Campaign Number: 19V515000 (Fuel System, Gasoline) as a cause for the failure; however, her VIN was not included in the recall. The local dealer was made aware of the failure and confirmed that the VIN was not included in the recall. The vehicle was not repaired. The manufacturer made aware of the failure and a case was opened and the contact was advised to file a complaint with the NHTSA Hotline. The approximate failure mileage was 96,000.
NHTSA ODI #11486773
82,000 miles · Sep 14, 2022
Fuel System, Gasoline
The contact owns a 2017 Ford Focus. The contact stated while driving approximately 5 MPH and attempting to park the vehicle, the check engine warning light illuminated. The contact stated that the vehicle was shuddering while driving above 60 MPH or whenever the accelerator pedal was depressed while driving up hill. The vehicle …
Read full complaint
The contact owns a 2017 Ford Focus. The contact stated while driving approximately 5 MPH and attempting to park the vehicle, the check engine warning light illuminated. The contact stated that the vehicle was shuddering while driving above 60 MPH or whenever the accelerator pedal was depressed while driving up hill. The vehicle was taken to an independent mechanic to be diagnosed. The contact was informed that the fuel tank needed to be replaced. The contact referenced NHTSA Campaign Number: 18V735000 (Fuel System, Gasoline) as a possible solution however, the VIN was not included in the recall. The vehicle was not repaired. The manufacturer was made aware of the failure and confirmed that the VIN was not included in the recall. The manufacturer referred the contact to the NHTSA Hotline. The failure mileage was approximately 82,000.
NHTSA ODI #11484433
Mileage unknown · Sep 1, 2022
Fuel System, Gasoline
The contact owns a 2017 Ford Focus. The contact stated that after refueling the vehicle, the vehicle failed to start immediately. The vehicle would start after several attempts but would shudder and then turn off independently. Additionally, the contact stated that while driving at an undisclosed speed, the vehicle jerked and d…
Read full complaint
The contact owns a 2017 Ford Focus. The contact stated that after refueling the vehicle, the vehicle failed to start immediately. The vehicle would start after several attempts but would shudder and then turn off independently. Additionally, the contact stated that while driving at an undisclosed speed, the vehicle jerked and decelerated independently. The check engine warning light was illuminated. The contact was able to continue driving; however, the failure recurred after refueling. The vehicle was taken to an independent mechanic where it was diagnosed that the fuel tank was collapsing internally due to a stuck canister purge valve failure. The independent mechanic also informed the contact that each time she had refueled the vehicle, air was being pushed into the fueling system. The independent mechanic informed the contact that the failure was associated with NHTSA Campaign Number: 19V515000 (Fuel System, Gasoline). The dealer was notified of the failure and an appointment was scheduled. The manufacturer was notified of the failure and informed the contact that the vehicle could not be repaired under NHTSA Campaign Number: 19V515000 (Fuel System, Gasoline) due to the manufactured date of the vehicle. The vehicle was not repaired. The failure mileage was unknown.
NHTSA ODI #11482384
49,763 miles · Aug 24, 2022
Fuel System, Gasoline
The contact called on behalf of a client who owns a 2017 Ford Focus. The contact stated the client was at a stop light when the vehicle stalled. The check engine warning light illuminated. The client restarted the vehicle and drove to the independent mechanic. The mechanic diagnosed the failure to be a stuck canister purge valve…
Read full complaint
The contact called on behalf of a client who owns a 2017 Ford Focus. The contact stated the client was at a stop light when the vehicle stalled. The check engine warning light illuminated. The client restarted the vehicle and drove to the independent mechanic. The mechanic diagnosed the failure to be a stuck canister purge valve. The mechanic also related the failure to NHTSA Campaign Number: 18V735000 (Fuel System, Gasoline). The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 49,763.
NHTSA ODI #11481016
96,000 miles · Aug 5, 2022
Fuel System, Gasoline
The contact owns a 2017 Ford Focus. The contact stated that after refueling the vehicle and driving 40 MPH, the vehicle stalled. The check engine warning light was illuminated. The contact was able to veer to the side of the road. The contact was able to restart the vehicle and continued driving; however, the contact stated that…
Read full complaint
The contact owns a 2017 Ford Focus. The contact stated that after refueling the vehicle and driving 40 MPH, the vehicle stalled. The check engine warning light was illuminated. The contact was able to veer to the side of the road. The contact was able to restart the vehicle and continued driving; however, the contact stated that the failure had been reoccurring after refueling. The vehicle was taken to an independent mechanic where it was diagnosed that fuel tank vacuum system had failed. The vehicle was not repaired. The dealer was notified of the failure and informed the contact that her vehicle could not be repaired under an unknown recall as the VIN was not included. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA. The failure mileage was approximately 96,000.
NHTSA ODI #11477713
30,000 miles · Jul 25, 2022
Fuel System, Gasoline
The contact's wife owns a 2017 Ford Focus. The contact stated that soon after refueling the vehicle, the vehicle shut off without warning. The contact stated that his wife would depress the accelerator pedal to prevent the vehicle from inadvertently stalling. The contact stated that initially, no warning lights had appeared on t…
Read full complaint
The contact's wife owns a 2017 Ford Focus. The contact stated that soon after refueling the vehicle, the vehicle shut off without warning. The contact stated that his wife would depress the accelerator pedal to prevent the vehicle from inadvertently stalling. The contact stated that initially, no warning lights had appeared on the instrument panel; however, recently the check engine warning light had illuminated. The vehicle was initially taken to the dealer however, the mechanic found no failure with the vehicle. The contact then took the vehicle to an independent mechanic where a diagnostic test showed that the vehicle had a defective PCV valve. The vehicle was taken back to the dealer where the mechanic informed him that he was familiar with the failure; however, he was provided an estimate for a diagnostic fee. Upon investigation, the contact linked the failure to NHTSA Campaign Number: 18V735000 (Fuel System, Gasoline) however, the VIN was not included in the recall. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was approximately 30,000.
NHTSA ODI #11475644
83,000 miles · Apr 27, 2022
Fuel System, GasolineFire
The contact owns a 2017 Ford Focus ST. The contact stated that when he proceeded to start his vehicle, the vehicle would not start. The contact stated that he then had his vehicle towed to an independent mechanic who was able to start his vehicle by placing air in the fuel tank. The contact stated that once the vehicle started,…
Read full complaint
The contact owns a 2017 Ford Focus ST. The contact stated that when he proceeded to start his vehicle, the vehicle would not start. The contact stated that he then had his vehicle towed to an independent mechanic who was able to start his vehicle by placing air in the fuel tank. The contact stated that once the vehicle started, there was a huge amount of black smoke. The contact stated that he was advised by the mechanic that he had a deforming fuel tank that was causing the failure. The contact stated that no warning lights had illuminated the vehicle at the time. The contact stated that he was able to drive his vehicle back to his residence, however, when he attempted to restart the vehicle, it would not start. The contact stated that he then contacted both the dealer and manufacturer who advised him that there was a recall, however, his vehicle was not a part of the recall NHTSA campaign 19V515000 (Fuel System, Gasoline). The failure mileage was 83,000.
NHTSA ODI #11462512
55,000 miles · Apr 13, 2022
Fuel System, Gasoline
The contact owns a 2017 Ford Focus. The contact stated that while driving the vehicle off the lot, the engine fault and the service engine warning light illuminated on the instrument panel. Additionally, after refueling, the vehicle would inadvertently stall. The vehicle was taken to the local dealer and diagnosed; however, the …
Read full complaint
The contact owns a 2017 Ford Focus. The contact stated that while driving the vehicle off the lot, the engine fault and the service engine warning light illuminated on the instrument panel. Additionally, after refueling, the vehicle would inadvertently stall. The vehicle was taken to the local dealer and diagnosed; however, the mechanic was unable to determine the cause of the failure. The contact stated that an unknown software update was performed. The vehicle was not repaired. The manufacturer was notified of the failure. The contact related the failure to NHTSA Campaign Number: 18V735000 (Fuel System, Gasoline). The approximate failure mileage was 55,000.
NHTSA ODI #11460658
Official recalls
10Jun 9, 2026
Ford Motor Company (Ford) is recalling certain 2012-2018 Focus vehicles previously repaired incorrectly under recall number 18V735. The Canister Purge Valve (CPV) may malfunction, causing the engine to stall unexpectedly while driving.
Consequence & remedy
Consequence: An engine that stalls while driving increases the risk of a crash.
Remedy: Dealers will update the powertrain control module (PCM) software, free of charge. Owner notification letters were mailed July 29, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S40. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov on July 6,2026.
Jun 9, 2026
Ford Motor Company (Ford) is recalling certain 2015-2018 Focus and 2013-2016 Fusion vehicles previously repaired incorrectly under recall numbers 18V169 and 18V845. The clutch may fracture, resulting in damage to the transmission assembly and possibly a transmission fluid leak.
Consequence & remedy
Consequence: A transmission fluid leak in the presence of an ignition source such as hot engine or exhaust components can increase the risk of a fire.
Remedy: Dealers will update the software, free of charge. Additionally, dealers will inspect Focus vehicles and replace the clutch assembly as necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed August 5, 2026. Additional letters will be sent once the remedy is available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S43. Vehicle Identification Numbers (VINs) involved in this recall will become searchable on NHTSA.gov on July 6,2026.
Jan 15, 2026
Ford Motor Company (Ford) is recalling certain 2013-2018 Focus, 2013-2019 Escape, and 2015-2016 MKC vehicles equipped with a 2.0L engine. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
Consequence & remedy
Consequence: An electrical short circuit can increase the risk of a fire.
Remedy: Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed March 6, 2026. Additional letters will be sent once the final remedy is available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S01. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on January 16, 2026.
Jan 15, 2026
Ford Motor Company (Ford) is recalling certain 2016-2018 Focus, 2019 Explorer, and 2024 Explorer vehicles. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
Consequence & remedy
Consequence: An electrical short circuit can increase the risk of a fire.
Remedy: Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded blanking plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed February 13, 2026. Additional letters will be sent once the final remedy is available, anticipated in October 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SA4. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on January 16, 2026. This recall expands previous recall number 25V685.
Dec 22, 2023
Ford Motor Company (Ford) is recalling certain 2016-2018 Ford Focus and 2018-2022 Ford EcoSport vehicles. The oil pump drive belt or drive belt tensioner may fail, resulting in a loss of engine oil pressure.
Consequence & remedy
Consequence: A loss of oil pressure can result in an engine stall and a loss of power braking assist, increasing the risk of a crash.
Remedy: Dealers will replace the oil pump tensioner assembly and oil pump drive belt, free of charge. If engine failure occurs due to a damaged oil pump belt and/or oil pump belt tensioner, Ford has authorized dealers to replace the engine assembly as an interim repair before the availability of remedy parts for the final repair. This repair will be free of charge (parts and labor). Owner notification letters were mailed August 11, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S64.
Jul 5, 2019
Ford Motor Company (Ford) is recalling certain 2012 and 2017 Focus vehicles equipped with 2.0L GDI gasoline engines and 2013-2014 Focus ST vehicles equipped with 2.0L GTDI engines, previously recalled under 18V-735. The affected vehicles did not have the Powertrain Control Module (PCM) updated as intended. Therefore, the Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in the fuel vapor management system.
Consequence & remedy
Consequence: The excessive vacuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began July 29, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S22.
Additional source detail variants (2)
Fuel System, Gasoline:storage:evaporative Emissions:canister
Ford Motor Company (Ford) is recalling certain 2012 and 2017 Focus vehicles equipped with 2.0L GDI gasoline engines and 2013-2014 Focus ST vehicles equipped with 2.0L GTDI engines, previously recalled under 18V-735. The affected vehicles did not have the Powertrain Control Module (PCM) updated as intended. Therefore, the Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in the fuel vapor management system.
Consequence: The excessive vacuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began July 29, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S22.
Fuel System, Gasoline:storage
Ford Motor Company (Ford) is recalling certain 2012 and 2017 Focus vehicles equipped with 2.0L GDI gasoline engines and 2013-2014 Focus ST vehicles equipped with 2.0L GTDI engines, previously recalled under 18V-735. The affected vehicles did not have the Powertrain Control Module (PCM) updated as intended. Therefore, the Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in the fuel vapor management system.
Consequence: The excessive vacuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began July 29, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S22.
Nov 28, 2018
Ford Motor Company (Ford) is recalling certain 2016-2018 Ford Focus vehicles equipped with a 1.0L Fox GTDI engine and a 6-speed manual transmission. The clutch may fracture, resulting in damage to the transmission assembly and possibly a transmission fluid leak.
Consequence & remedy
Consequence: A transmission fluid leak in the presence of an ignition source such as hot engine or exhaust components can increase the risk of a fire.
Remedy: Ford will notify owners, and dealers will update vehicles with software that detects and prevents prolonged clutch slip, and will replace the clutch, as necessary, free of charge. The recall began January 17, 2019. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 18S07. Note: This recall is an expansion of Recall 18V-169.
Oct 22, 2018
Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.
Consequence & remedy
Consequence: The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1-866-436-7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.
Additional source detail variants (2)
Fuel System, Gasoline:storage:evaporative Emissions:canister
Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.
Consequence: The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1-866-436-7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.
Fuel System, Gasoline:storage
Ford Motor Company (Ford) is recalling certain 2012-2018 Ford Focus vehicles with a 2.0L GDI or 2.0L GTDI engine. The Canister Purge Valve (CPV) may malfunction, possibly causing excessive vacuum in fuel vapor management system.
Consequence: The excessive vaccuum may result in an engine stall while driving, without warning and without the ability to restart the vehicle, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the Powertrain Control Module. Dealers will also check for fault codes and replace the CPV as needed. If the CPV is replaced, dealers will inspect and replace the carbon canister, fuel tank and fuel delivery module as necessary. The recall began August 19, 2019. Owners may contact Ford Customer service at 1-866-436-7332. Ford's number for this recall is 18S32. Note: Until the vehicle is serviced for this concern, owners are advised to keep the fuel tank at least halfway full.
Aug 28, 2017
Ford Motor Company (Ford) is recalling certain 2017 Focus vehicles. The rear left side seat back frame may have an insufficient weld between the outboard pivot bracket and the pivot nut joint, resulting in the seat back having reduced strength. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 207, "Seating Systems," and 210, "Seat Belt Assembly Anchorages."
Consequence & remedy
Consequence: The reduced seat back strength may increase the risk of injury in the event of a crash.
Remedy: Ford will notify owners, and dealers will inspect and replace the rear second left side rear seat back as necessary, free of charge. The recall began October 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17C13.
Additional source detail variants (2)
Seats:mid/rear Assembly
Ford Motor Company (Ford) is recalling certain 2017 Focus vehicles. The rear left side seat back frame may have an insufficient weld between the outboard pivot bracket and the pivot nut joint, resulting in the seat back having reduced strength. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 207, "Seating Systems," and 210, "Seat Belt Assembly Anchorages."
Consequence: The reduced seat back strength may increase the risk of injury in the event of a crash.
Remedy: Ford will notify owners, and dealers will inspect and replace the rear second left side rear seat back as necessary, free of charge. The recall began October 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17C13.
Seat Belts:rear/other
Ford Motor Company (Ford) is recalling certain 2017 Focus vehicles. The rear left side seat back frame may have an insufficient weld between the outboard pivot bracket and the pivot nut joint, resulting in the seat back having reduced strength. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 207, "Seating Systems," and 210, "Seat Belt Assembly Anchorages."
Consequence: The reduced seat back strength may increase the risk of injury in the event of a crash.
Remedy: Ford will notify owners, and dealers will inspect and replace the rear second left side rear seat back as necessary, free of charge. The recall began October 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17C13.
Sep 28, 2016
Ford Motor Company (Ford) is recalling certain model year 2013-2017 Ford Focus hatchback vehicles manufactured February 14, 2012, to August 26, 2016 and equipped with a manual transmission. The hatchback of the affected vehicles may be unlatched with a single press of the interior latch release button. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."
Consequence & remedy
Consequence: With only a single press needed, the driver may accidently unlatch the hatchback, increasing the risk of injury to any unsecured passengers in the back.
Remedy: Ford will notify owners, and dealers will reprogram the Body Control Module with updated software, free of charge. The recall began February 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C13.
Additional source detail variants (2)
Latches/locks/linkages:hatchback/liftgate:lock
Ford Motor Company (Ford) is recalling certain model year 2013-2017 Ford Focus hatchback vehicles manufactured February 14, 2012, to August 26, 2016 and equipped with a manual transmission. The hatchback of the affected vehicles may be unlatched with a single press of the interior latch release button. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."
Consequence: With only a single press needed, the driver may accidently unlatch the hatchback, increasing the risk of injury to any unsecured passengers in the back.
Remedy: Ford will notify owners, and dealers will reprogram the Body Control Module with updated software, free of charge. The recall began February 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C13.
Structure:body:hatchback/liftgate
Ford Motor Company (Ford) is recalling certain model year 2013-2017 Ford Focus hatchback vehicles manufactured February 14, 2012, to August 26, 2016 and equipped with a manual transmission. The hatchback of the affected vehicles may be unlatched with a single press of the interior latch release button. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 206, "Door Locks and Door Retention Components."
Consequence: With only a single press needed, the driver may accidently unlatch the hatchback, increasing the risk of injury to any unsecured passengers in the back.
Remedy: Ford will notify owners, and dealers will reprogram the Body Control Module with updated software, free of charge. The recall began February 10, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16C13.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
5EA26004 · Timing Belt Failure
Opened Jul 31, 2026 · No close date supplied
Status: open (inferred from source dates) · Engine; Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE25020 · Timing Belt Failure
Opened Dec 18, 2025 · Closed Jul 31, 2026
Status: closed (inferred from source dates) · Engine; Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE23015 · Oil Pump Failure
Opened Sep 20, 2023 · Closed Feb 14, 2024
Status: closed (inferred from source dates) · Engine And Engine Cooling:engine:oil/lubrication:pump
On September 20, 2023, the Office of Defects Investigation (ODI) opened PE23-015 to investigate instances of engine failure due to loss of oil pressure in model year (MY) 2018-2021 Ford EcoSport vehicles. Some consumers reported a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle was in motion. The investigation revealed that the engine oil pump drive belt tensioner arm may fracture, separate from the tensioner backing plate, and/or the oil pump drive belt may degrade and lose teeth, resulting in a loss of engine oil pressure. A loss of engine oil pressure can result in engine seizure, which can result in a loss of motive power and a loss of mechanical vacuum pump required to provide power braking assist, increase the risk of a crash. On December 22, 2023, Ford filed recall 23V-905 for certain MY 2016-2018 Ford Focus and 2018-2022 Ford EcoSport vehicles. The recall remedy provides the replacement of the oil pump drive belt tensioner assembly and oil pump drive belt with redesigned parts to improve robustness. In view of the recall action being taken by Ford, ODI is closing this Preliminary Evaluation. The agency reserves the right to take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
RQ23006 · Loss Of Motive Power
Opened Sep 15, 2023 · Closed Dec 20, 2024
Status: closed (inferred from source dates) · Fuel System, Gasoline:storage:evaporative Emissions:canister
On September 15, 2023, the Office of Defect Investigation (ODI) opened this Recall Query (RQ) after receiving 98 consumer complaints alleging loss of motive power in model year (MY) 2012-2018 Ford Focus vehicles. The RQ focused on the effectiveness of the remedies of Recall 18V-735 and 19V-515. In October 2018, Ford issued Recall 18V-735, which updated Powertrain Control Module (PCM) software in MY 2012-2018 Ford Focus vehicles equipped with 2.0L GDI engines built prior to April 13, 2017, and those with 2.0L GTDI engines built prior to February 2, 2018. The recall addressed vehicles experiencing a malfunctioning Canister Purge Valve (CPV) that can stick open and PCM software that does not adequately detect a stuck-open CPV condition. A CPV that is stuck open can cause excessive vacuum in the fuel vapor management system, potentially deforming the fuel tank, collapsing on itself. This deformation of the fuel tank can cause a Malfunction Indicator Light (MIL) to illuminate, an inaccurate or erratic fuel gauge indication, drivability issues, and/or loss of motive power. In July 2019, Ford issued Recall 19V-515, which addressed certain MY 2012 and MY 2017 Ford Focus vehicles equipped with 2.0L GDI and MY 2013-2014 Ford Focus vehicles equipped with 2.0L GTDI engines whose PCM software had been reprogrammed as a part of recall 18V-735. The updated software calibrations for these subject vehicles were not properly installed by Ford at the time of production. Approximately one year after this RQ was opened, on September 25, 2024, Ford initiated a customer satisfaction program (24N07) for MY 2012-2018 Ford Focus vehicles equipped with the 2.0L GDI and GTDI engines to—as ODI learned during this investigation—address a different issue with the CPV from the primary focus of the safety recalls (18V-735 and 19V-515). Ford stated the CPV may not operate as intended in these vehicles. A failed CPV on its own merit, may cause drivability concerns such as engine hesitation, running rough, or stalling at low speed, which will be accompanied by an illuminated MIL. This program provides a one-time replacement of the CPV for vehicles with 15 years of service or less (with no mileage restriction). This coverage will automatically transfer to subsequent owners. It is to be noted that the customer satisfaction program being taken by Ford to address this RQ investigation results in a much different and significantly less severe problem than the safety action taken to remedy 18V-735 and 19V-515. ODI found no further issues with the combined scope and severity related to 18V-735 and 19V-515 therefore, ODI is closing this Recall Query. The agency reserves the right to take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
Illustration