← New search

2019 Ford Flex

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2019 Ford Flex do not stand out strongly from the model-year median of 139.

About this comparison →

How this year compares

Owner complaints by model year

Other model years Selected year
Compare all Flex years →

Counts vary with age, sales and reporting. They are not failure rates.

What owners reported most

All reported categories

Tap a category to read its complaints. One report may name several components.

When problems were reported

Mileage at the reported incident

104 reports with mileage · 141 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Back Over Prevention. Review the 136 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Structure. Review the 55 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 22 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

4 crash reports0 fire reports1 injury reports

What owners actually said

245 reports
95,000 miles · Jun 20, 2025
Visibility

The contact owns a 2019 Ford Flex. The contact stated that after it had rained, the front driver’s side footwell filled up with water. The vehicle was taken to the dealer where the mechanic discovered that the drain in the sunroof was clogged. The dealer was aware of the failure and repaired the vehicle. The contact recently sta…

Read full complaint

The contact owns a 2019 Ford Flex. The contact stated that after it had rained, the front driver’s side footwell filled up with water. The vehicle was taken to the dealer where the mechanic discovered that the drain in the sunroof was clogged. The dealer was aware of the failure and repaired the vehicle. The contact recently stated that the failure had returned and the driver’s and passenger’s side footwells were filled with water. The contact also stated that the headliner had become stained and soaked with water. Additionally, the contact stated that there was a mildew odor inside the vehicle due to the failure. The manufacturer was notified of the failure but offered no assistance. The contact was referred to the NHTSA to report the failure. The vehicle was not repaired. The failure mileage was approximately 95,000.

NHTSA ODI #11668067

Mileage unknown · Jun 18, 2025
Visibility/wiper

Rear view back up camera failed. The repair solution is long overdue.

NHTSA ODI #11667857

40,000 miles · Jun 13, 2025
Structure

The contact owns a 2019 Ford Flex. The contact stated that while driving 65 MPH, the driver's side B-pillar trim detached from the vehicle. The vehicle was not diagnosed or repaired. The contact stated that on another occasion, the passenger’s side B-pillar trim became loosened. The contact removed the passenger side B-pillar tr…

Read full complaint

The contact owns a 2019 Ford Flex. The contact stated that while driving 65 MPH, the driver's side B-pillar trim detached from the vehicle. The vehicle was not diagnosed or repaired. The contact stated that on another occasion, the passenger’s side B-pillar trim became loosened. The contact removed the passenger side B-pillar trim due to safety concerns. The vehicle was not diagnosed or repaired after the most recent failure. The contact related the failure to TSB: 202427. However, the part to do the repair was not yet available. The manufacturer was not made aware of the issue. The failure mileage was approximately 40,000.

NHTSA ODI #11666758

24,000 miles · Jun 12, 2025
Back Over Prevention

The contact owns a 2019 Ford Flex. The contact stated that while his wife was reversing, the rearview camera image was blue, and the screen displayed an unknown message. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The contact received notification of NHTSA Campaign Number: 24V951000(Back …

Read full complaint

The contact owns a 2019 Ford Flex. The contact stated that while his wife was reversing, the rearview camera image was blue, and the screen displayed an unknown message. The vehicle was not diagnosed or repaired by an independent mechanic or the dealer. The contact received notification of NHTSA Campaign Number: 24V951000(Back Over Prevention); however, the part to do the repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The failure mileage was 24,000. VIN tool confirms parts not available.

NHTSA ODI #11666493

105,000 miles · Jun 9, 2025
Back Over Prevention

The contact owns a 2019 Ford Flex. The contact stated while reversing, the back over prevention camera failed to display a rear-view image, compromising the back over prevention system. The contact stated that the message "Rear-view camera unavailable" was displayed. The contact stated that the vehicle returned to normal functio…

Read full complaint

The contact owns a 2019 Ford Flex. The contact stated while reversing, the back over prevention camera failed to display a rear-view image, compromising the back over prevention system. The contact stated that the message "Rear-view camera unavailable" was displayed. The contact stated that the vehicle returned to normal functionality, but the failure became a regular occurrence. No warning lights were illuminated. The vehicle was not taken to the dealer or an independent mechanic. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 24V951000 (Back Over Prevention); but the VIN was not included. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 105,000.

NHTSA ODI #11665907

Mileage unknown · Jun 9, 2025
Unknown Or Other

Backup camera has not worked for long time. Bartow Ford said part not available for recall but if I want to pay 823, they have the part. Without a backup camera it is like backing up a whale blindfolded.

NHTSA ODI #11665842

Mileage unknown · Jun 9, 2025
Back Over Prevention

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (BACK OVER PREVENTION); however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact stated that the manufacturer had exceede…

Read full complaint

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (BACK OVER PREVENTION); however, the part to do the recall repair was unavailable. The local dealer was contacted, and it was confirmed that the part was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact experienced the failure, and the display screen image was distorted or upside down. The contact stated that the failure almost caused vehicle to strike a pedestrian. The cause of the failure was not yet determined. VIN tool confirms parts not available.

NHTSA ODI #11665723

Mileage unknown · Jun 6, 2025
Structure

On 6/4/2025, the driver side front door B-pillar trim piece separated from the vehicle. The tape that joins the trim piece to the door sheet metal completely sheared. The adhesive is still fine but the form separated. The part is connected only to the door through the wire hardness of the keyless entry. TSB 20-2427 stated the…

Read full complaint

On 6/4/2025, the driver side front door B-pillar trim piece separated from the vehicle. The tape that joins the trim piece to the door sheet metal completely sheared. The adhesive is still fine but the form separated. The part is connected only to the door through the wire hardness of the keyless entry. TSB 20-2427 stated the issue is "loose". But the actual issue is a flying part with a connecting string.

NHTSA ODI #11665417

66,000 miles · May 30, 2025
Back Over Prevention

The contact owns a 2019 Ford Flex. The contact stated that while attempting to reverse out of a parking spot, the rearview camera image displayed on the screen was displayed upside down. There was no warning light illuminated. The local dealer was contacted; however, the vehicle was not diagnosed or repaired. The contact was inf…

Read full complaint

The contact owns a 2019 Ford Flex. The contact stated that while attempting to reverse out of a parking spot, the rearview camera image displayed on the screen was displayed upside down. There was no warning light illuminated. The local dealer was contacted; however, the vehicle was not diagnosed or repaired. The contact was informed that the VIN was not under recall. The vehicle was not repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 66,000.

NHTSA ODI #11663936

74,000 miles · May 28, 2025
Back Over Prevention

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware o…

Read full complaint

The contact owns a 2019 Ford Flex. The contact received notification of NHTSA Campaign Number: 24V951000 (Back Over Prevention); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The contact stated that the rear-view camera had experienced intermittent failures, with the image frozen or distorted. The failure mileage was approximately 74,000. VIN tool confirms parts not available.

NHTSA ODI #11663354

Official recalls

4

25V732000 · Structure:body

Oct 24, 2025

Ford Motor Company (Ford) is recalling certain 2017-2019 Flex vehicles. The driver and front passenger B-Pillar door trim may detach while driving.

Consequence & remedy

Consequence: Door trim that detaches while driving can create a road hazard, increasing the risk of a crash.

Remedy: Dealers will repair or replace the B-pillar trim as necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed December 17, 2025. Additional letters will be sent once the remedy is available, anticipated March 2027. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SB8. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 28, 2025.

25V695000 · Back Over Prevention: Sensing System: Camera

Oct 13, 2025

Ford Motor Company (Ford) is recalling certain 2015-2019 Flex, 2015 Explorer, Lincoln MKT, Lincoln MKZ, 2015-2016 C-Max, Escape, Taurus, 2016 Fusion, 2018-2019 Taurus, 2019 Lincoln MKT, Fiesta, and 2020 Mustang vehicles. The rearview camera may display a distorted, intermittent, or blank image when the vehicle is in reverse.

Consequence & remedy

Consequence: A rearview camera that fails to properly display an image can reduce the driver’s view behind the vehicle, increasing the risk of a crash.

Remedy: Dealers will inspect and replace the rearview camera as necessary, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on October 25, 2025. Additional letters will be mailed once the final remedy is available on each phase. Mustang owner notification letters were mailed January 2, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SA9. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 14, 2025.

24V951000 · Back Over Prevention: Sensing System: Camera

Dec 20, 2024

Ford Motor Company (Ford) is recalling certain 2019 Flex, Fiesta, and Lincoln MKT vehicles. The rearview camera may intermittently display a blank or distorted image.

Consequence & remedy

Consequence: A rearview camera that displays a blank or distorted image can reduce the drivers view of what is behind the vehicle, increasing the risk of a crash.

Remedy: Dealers will replace the rearview camera as necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed January 22, 2025. A second notice will be sent once the final remedy is available, anticipated March 2027. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 24S75.

18V548000 · Electrical System:alternator/generator/regulator; Electrical System:starter Assembly

Aug 20, 2018

Ford Motor Company (Ford) is recalling certain 2018 Ford Edge, Lincoln MKX, 2019 Ford Flex, and Lincoln MKT vehicles. The power supply cables at the starter and the alternator may not have been properly secured, possibly resulting in an electrical arc.

Consequence & remedy

Consequence: An electrical arc can increase the risk of a fire.

Remedy: Ford will notify owners, and dealers will inspect the alternator and starter motor power supply cables to verify that they are properly secured, correcting them as necessary, free of charge. The recall began September 26, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S25.

Additional source detail variants (2)

Electrical System:starter Assembly

Ford Motor Company (Ford) is recalling certain 2018 Ford Edge, Lincoln MKX, 2019 Ford Flex, and Lincoln MKT vehicles. The power supply cables at the starter and the alternator may not have been properly secured, possibly resulting in an electrical arc.

Consequence: An electrical arc can increase the risk of a fire.

Remedy: Ford will notify owners, and dealers will inspect the alternator and starter motor power supply cables to verify that they are properly secured, correcting them as necessary, free of charge. The recall began September 26, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S25.

Electrical System:alternator/generator/regulator

Ford Motor Company (Ford) is recalling certain 2018 Ford Edge, Lincoln MKX, 2019 Ford Flex, and Lincoln MKT vehicles. The power supply cables at the starter and the alternator may not have been properly secured, possibly resulting in an electrical arc.

Consequence: An electrical arc can increase the risk of a fire.

Remedy: Ford will notify owners, and dealers will inspect the alternator and starter motor power supply cables to verify that they are properly secured, correcting them as necessary, free of charge. The recall began September 26, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S25.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

PE25007 · B-Pillar Trim Detachment

Opened Aug 7, 2025 · Closed Aug 5, 2026

Status: closed (inferred from source dates) · Structure:body:roof And Pillars

On August 7, 2025, the Office of Defects Investigation (ODI) opened PE25007 to investigate instances of B-pillar trim detachment in model year (MY) 2019 Ford Flex vehicles manufactured by Ford Motor Company. During the investigation, MY 2011-2018 Ford Flex vehicles were analyzed as peer vehicles, and subsequently incorporated into the subject population because they use B-pillar trim pieces that are substantially similar to those used on the MY 2019 Ford Flex vehicles. In July 2025, prior to the opening of PE25007, ODI and Ford met to discuss B-pillar trim detachment in Ford Flex vehicles. Ford reported that its warranty analysis indicated that Flex B-pillar trim had a low detachment rate and that Ford did not believe this condition posed an unreasonable risk to motor vehicle safety. In July 2025, Ford closed its internal investigation. Because ODI’s analysis of complaint data indicated a high failure rate and an increasing failure trend, PE25007 was subsequently opened. In responding to the information request for PE25007, Ford reassessed the warranty search criteria used in its July 2025 internal investigation. The reassessment found the detachment rate to be substantially higher than what Ford had originally determined. Consequently, in October 2025, Ford issued recall 25V732based on the reassessed and accurate high failure rate. This recall instructed dealers to inspect the driver and front passenger B-pillar trim pieces and repair/replace if necessary. The vehicles included in this recall were MY 2017-2019 Ford Flex with production dates between February 17, 2017 and December 2, 2019. In January 2026, Ford issued 25V732 Amendment 1, which updated the remedy to remove the inspection criteria and instead proactively secure the driver and front passenger B-pillar trim with adhesive. The scope of vehicles included in the recall was unchanged by Amendment 1. ODI’s analysis of 25V732 found that both the scope and remedy were insufficient and that an unreasonable safety risk remained despite the recall. MY 2016 Ford Flex was excluded from the recall scope and the rear B-pillar trims on both the driver and passenger side were excluded from the recall. The failure rates of both MY 2016 Ford Flex and rear B-pillar trim pieces were found to be higher than the failure rates in similar trim detachment recalls issued by both Ford and other vehicle manufacturers. Starting in January 2026, ODI and Ford had multiple meetings to discuss Ford’s PE25007 response data and ODI’s concern about the 25V732 scope and remedy. In June 2026, Ford issued 25V732 Amendment 2. This amendment expanded the scope of the recall to add MY 2016-2017 Ford Flex vehicles produced before February 17, 2017. Additionally, this amendment updated the remedy to include removal of and reapplication or replacement of both rear driver and rear passenger B-pillar trim pieces in addition to front driver and front passenger B-pillar trim pieces. This updated remedy applies to all MY 2016-2019 vehicles. Ford expects to complete the mailing of remedy owner notification letters by March 26, 2027. Also, Ford informed ODI that prior model year (MY 2011-2015) vehicles were referred to Ford’s Customer Satisfaction forum for consideration of an extended warranty program. In view of recall 25V732 and its associated amendments, ODI is closing this Preliminary Evaluation (PE). The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

PE24030 · Rear-view Camera Failure

Opened Oct 11, 2024 · Closed Feb 2, 2026

Status: closed (inferred from source dates) · Back Over Prevention: Sensing System: Camera

On October 11, 2024, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE24030) to assess alleged failures of the rear-view camera in Model Year (MY) 2019 Ford Flex vehicles. Complaints submitted to NHTSA through Vehicle Online Questionnaires (VOQs), reviewed by ODI, report blank, distorted, or inverted rear-view camera images when in reverse. An inverted or upside-down image can provide false information to the driver increasing the risk of a crash. To date, ODI has received 85 VOQ complaints and additional EWR Field Reports with these allegations for MY 2019 Ford Flex vehicles. During the investigation, ODI found that the MY 2019 Ford Flex vehicle and certain peer vehicles including MY 2015-2018 Flex, MY 2019 Fiesta, Taurus, and Lincoln MKT vehicles are equipped with Magna analog rear-view-only cameras. On December 20, 2024, Ford filed Recall 24V-951 covering 30,715 MY 2019 Ford Flex, Ford Fiesta, and Lincoln MKT vehicles in which the rear-view camera may intermittently display a blank or distorted image. The dealers will replace the rear-view camera for vehicles in the recall population. Per the recall chronology, teardown of three cameras identified fractured solder joints between the microcontroller and the printed circuit board. Ford indicated that other causal factors are being investigated and asserted that the defect is contained within the camera. ODI found that certain peer vehicles excluded from Recall 24V-951 showed a high rate of VOQ complaints.  Also, ODI identified reports produced by Ford that indicate the peer vehicles have the same issue as the subject vehicles. To address ODI’s concern, Ford analyzed some field-returned cameras, as well as Ford’s field data and ODI’s VOQ data. Ford stated it did not identify a specific root cause in the Magna supplied cameras. However, on October 13, 2025, Ford filed Recall 25V-695 covering 1,448,655 vehicles of various Ford/Lincoln models equipped with Magna supplied cameras. The cameras demonstrate the same blank or distorted images that prompted Recall 24V-951. It should be noted that Ford is conducting a recall of those vehicles by model/model year that exhibit VOQ complaint rates greater than 10 per 100,000 vehicles. For the remaining vehicles (rates less than 10/100K), Ford is providing a warranty extension (15 years/unlimited miles). Ford has stated that the differences in the rates (field performance) are likely due to the differences in the camera related hardware, such as the wiring harness type that are specific by vehicle model/model year. In view of Ford filing Recall 24V-951 and Recall 25V-695 addressing the subject of this investigation, ODI is closing this Preliminary Evaluation. NHTSA reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

Additional source detail variants (2)

Back Over Prevention: Sensing System: Camera

On October 11, 2024, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE24030) to assess alleged failures of the rear-view camera in Model Year (MY) 2019 Ford Flex vehicles. Complaints submitted to NHTSA through Vehicle Online Questionnaires (VOQs), reviewed by ODI, report blank, distorted, or inverted rear-view camera images when in reverse. An inverted or upside-down image can provide false information to the driver increasing the risk of a crash. To date, ODI has received 85 VOQ complaints and additional EWR Field Reports with these allegations for MY 2019 Ford Flex vehicles. During the investigation, ODI found that the MY 2019 Ford Flex vehicle and certain peer vehicles including MY 2015-2018 Flex, MY 2019 Fiesta, Taurus, and Lincoln MKT vehicles are equipped with Magna analog rear-view-only cameras. On December 20, 2024, Ford filed Recall 24V-951 covering 30,715 MY 2019 Ford Flex, Ford Fiesta, and Lincoln MKT vehicles in which the rear-view camera may intermittently display a blank or distorted image. The dealers will replace the rear-view camera for vehicles in the recall population. Per the recall chronology, teardown of three cameras identified fractured solder joints between the microcontroller and the printed circuit board. Ford indicated that other causal factors are being investigated and asserted that the defect is contained within the camera. ODI found that certain peer vehicles excluded from Recall 24V-951 showed a high rate of VOQ complaints.  Also, ODI identified reports produced by Ford that indicate the peer vehicles have the same issue as the subject vehicles. To address ODI’s concern, Ford analyzed some field-returned cameras, as well as Ford’s field data and ODI’s VOQ data. Ford stated it did not identify a specific root cause in the Magna supplied cameras. However, on October 13, 2025, Ford filed Recall 25V-695 covering 1,448,655 vehicles of various Ford/Lincoln models equipped with Magna supplied cameras. The cameras demonstrate the same blank or distorted images that prompted Recall 24V-951. It should be noted that Ford is conducting a recall of those vehicles by model/model year that exhibit VOQ complaint rates greater than 10 per 100,000 vehicles. For the remaining vehicles (rates less than 10/100K), Ford is providing a warranty extension (15 years/unlimited miles). Ford has stated that the differences in the rates (field performance) are likely due to the differences in the camera related hardware, such as the wiring harness type that are specific by vehicle model/model year. In view of Ford filing Recall 24V-951 and Recall 25V-695 addressing the subject of this investigation, ODI is closing this Preliminary Evaluation. NHTSA reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

Back Over Prevention: Sensing System: Camera

On October 11, 2024, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE24030) to assess alleged failures of the rear-view camera in Model Year (MY) 2019 Ford Flex vehicles. Complaints submitted to NHTSA through Vehicle Online Questionnaires (VOQs), reviewed by ODI, report blank, distorted, or inverted rear-view camera images when in reverse. An inverted or upside-down image can provide false information to the driver increasing the risk of a crash. To date, ODI has received 85 VOQ complaints and additional EWR Field Reports with these allegations for MY 2019 Ford Flex vehicles. During the investigation, ODI found that the MY 2019 Ford Flex vehicle and certain peer vehicles including MY 2015-2018 Flex, MY 2019 Fiesta, Taurus, and Lincoln MKT vehicles are equipped with Magna analog rear-view-only cameras. On December 20, 2024, Ford filed Recall 24V-951 covering 30,715 MY 2019 Ford Flex, Ford Fiesta, and Lincoln MKT vehicles in which the rear-view camera may intermittently display a blank or distorted image. The dealers will replace the rear-view camera for vehicles in the recall population. Per the recall chronology, teardown of three cameras identified fractured solder joints between the microcontroller and the printed circuit board. Ford indicated that other causal factors are being investigated and asserted that the defect is contained within the camera. ODI found that certain peer vehicles excluded from Recall 24V-951 showed a high rate of VOQ complaints.  Also, ODI identified reports produced by Ford that indicate the peer vehicles have the same issue as the subject vehicles. To address ODI’s concern, Ford analyzed some field-returned cameras, as well as Ford’s field data and ODI’s VOQ data. Ford stated it did not identify a specific root cause in the Magna supplied cameras. However, on October 13, 2025, Ford filed Recall 25V-695 covering 1,448,655 vehicles of various Ford/Lincoln models equipped with Magna supplied cameras. The cameras demonstrate the same blank or distorted images that prompted Recall 24V-951. It should be noted that Ford is conducting a recall of those vehicles by model/model year that exhibit VOQ complaint rates greater than 10 per 100,000 vehicles. For the remaining vehicles (rates less than 10/100K), Ford is providing a warranty extension (15 years/unlimited miles). Ford has stated that the differences in the rates (field performance) are likely due to the differences in the camera related hardware, such as the wiring harness type that are specific by vehicle model/model year. In view of Ford filing Recall 24V-951 and Recall 25V-695 addressing the subject of this investigation, ODI is closing this Preliminary Evaluation. NHTSA reserves the right to take additional action if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.