IllustrationON HWY 65MPH ACCELERATING SPEEDOMETER READING WENT TO ZERO, TRANSMISSION AUTO DOWNSHIFT. HAD TO PULL OVER RESTART AND THEN BOTH THE SPEEDOMETER AND TRANSMISSION WORKED. AFTER THIS SEVERAL STARTS THE SPEEDOMETER DOESN'T WORK AND TRANSMISSION WON'T SHIFT OUT OF 1ST GEAR
2012 Ford F-150
Owner reports · Recalls · Investigations
More warning signs than most F-150 years
Owner complaints for the 2012 Ford F-150 are substantially higher than the model-year median of 676.
About this comparison →How this year compares
Owner complaints by model year
Compare all F-150 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
3550–25K
24225–50K
26450–75K
21775–100K
259100–150K
133150K+
1,470 reports with mileage · 310 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 678 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 482 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Steering. Review the 204 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
40 crash reports14 fire reports23 injury reports
Power Train complaints
678 reportsEXPERIENCED UNEXPECTED DOWNHIFT INTO FIRST GEAR AT HIGHWAY SPEED. TRANSMISSION WAS ERRATIC IN GEAR SELECTION WITH CORRESPONDING TACHOMETER AND SPEDOMETER OSCILLATIONS.HAD SIX OCCURENCES WITH VARIOUS DEGREES OF SEVERITY .CALLED FORD HELP LINE .ALL THEY SAID WAS THAT THERE WERE NO RECALLS ON THIS VEHICLE. VEHICLE IS " UNSAFE " TO …
Read full complaint
EXPERIENCED UNEXPECTED DOWNHIFT INTO FIRST GEAR AT HIGHWAY SPEED. TRANSMISSION WAS ERRATIC IN GEAR SELECTION WITH CORRESPONDING TACHOMETER AND SPEDOMETER OSCILLATIONS.HAD SIX OCCURENCES WITH VARIOUS DEGREES OF SEVERITY .CALLED FORD HELP LINE .ALL THEY SAID WAS THAT THERE WERE NO RECALLS ON THIS VEHICLE. VEHICLE IS " UNSAFE " TO DRIVE . GOT THE TRUCK INTO THE FORD DEALER AND HADF IT CODED. TRUCK WAS SHOWING CODES FOR DEFECTIVE OUTPUT SPEED SENSOR. THE " LEAD FRAME " HAD TO BE REPLACED AT " MY EXPENSE ". NO REPROGRAMMING WAS DONE BECAUSE THERE WAS " NO RECALL " AT THAT TIME . THE ROOT CAUSE WAS REPAIRED BUT THERE WAS STILL THE POSSIBILITY OF A VIOLENT DOWN SHIFT EVENT . I HAVE SINCE RECEIVED NOTIFICATION OF A EXPANDED RECALL TO REPROGRAM AND PREVENT THE DRAMATIC AND VIOLENT DOWNSHIFT ISSUE. I AM GOING TO GET THE TRUCK IN ASAP TO GET THIS DONE . THE ORIGINAL RECALL LANGUAGE STATED THAT IF THE VEHICLE WAS HAVING THE DOWNSHIFT ISSUES AND TESTED POSITIVE FOR DEFECTIVE OUTPUT SPEED SENSOR THAT FORD WOULD " REPLACE THE LEAD FRAME AND REPROGRAM " FREE OF CHARGE AND ALSO WARRANTEE THE COMPONENTS FOR I THINK 150,000 MILES. I FEEL THAT I HAVE HAD TO MAKE THIS VEHICLE " SAFE TO DRIVE " AT MY EXPENSE. THE REAL FIX IS TO REPLACE THE LEAD FRAME AND REPROGRAM . I WAS JUST LUCKY THAT THERE WAS NO ONCOMING TRAFFIC WHEN I EXPERIENCED THE DRAMATIC DOWN SHIFT INTO FIRST GEAR AND HAD TO MANUVER TO THE SHOULDER OF THE ROAD . I FEEL BAD FOR ANY ONE ELSE THAT HAS TO GO THROUGH THIS. FORD IS GETTING OFF ON THE " CHEAP ' BY NOT DOING THE " COMPLETE " FIX. VERY !!!!!!!!! UNHAPPY FORD OWNER.
TL* THE CONTACT OWNS A 2012 FORD F-150. THE CONTACT RECEIVED A RECALL NOTICE FOR NHTSA CAMPAIGN NUMBER: 19V075000 (POWER TRAIN). THE VEHICLE WAS TAKEN TO AUTONATION FORD LITTLETON (8252 S BROADWAY, LITTLETON, CO 80122) WHERE THEY REPROGRAMMED THE TRANSMISSION CONTROL MODULE. ONE WEEK LATER, THE CONTACT HAD TO TAKE THE VEHICLE BA…
Read full complaint
TL* THE CONTACT OWNS A 2012 FORD F-150. THE CONTACT RECEIVED A RECALL NOTICE FOR NHTSA CAMPAIGN NUMBER: 19V075000 (POWER TRAIN). THE VEHICLE WAS TAKEN TO AUTONATION FORD LITTLETON (8252 S BROADWAY, LITTLETON, CO 80122) WHERE THEY REPROGRAMMED THE TRANSMISSION CONTROL MODULE. ONE WEEK LATER, THE CONTACT HAD TO TAKE THE VEHICLE BACK TO THE DEALER BECAUSE THE TRANSMISSION WAS UNEXPECTEDLY DOWNSHIFTING INTO FIRST GEAR. THE DEALER STATED THAT THE TRANSMISSION NEEDED TO BE REPLACED. THE MANUFACTURER WAS CONTACTED. THE VEHICLE WAS CURRENTLY AT THE DEALER. THE FAILURE MILEAGE WAS 99,000.
THE 19S07 RECALL SERVICE WAS PERFORMED ON 3/19/19 AT BOB TOMES FORD MCKINNEY TX. TODAY, 3/20/19 THE DOWNSHIFT OCCURRED ON THE WAY TO WORK. I WAS TRAVELING AT APPROXIMATELY 45 MPH AND IT DOWNSHIFTED TO 1ST GEAR. I THOUGHT THIS IS WHAT THE RECALL WAS SUPPOSED TO FIX?
TL* THE CONTACT OWNS A 2012 FORD F-150. WHILE DRIVING APPROXIMATELY 55 MPH, THE VEHICLE SUDDENLY DOWNSHIFTED. THE CONTACT PULLED THE VEHICLE OVER TO THE SIDE OF THE ROAD AND THEN DROVE TO HARDY FAMILY FORD (1255 MARIETTA HWY, DALLAS, GA 30157) WHERE IT WAS DIAGNOSED THAT THE TRANSMISSION NEEDED TO BE REPLACED. THE CONTACT RECEIV…
Read full complaint
TL* THE CONTACT OWNS A 2012 FORD F-150. WHILE DRIVING APPROXIMATELY 55 MPH, THE VEHICLE SUDDENLY DOWNSHIFTED. THE CONTACT PULLED THE VEHICLE OVER TO THE SIDE OF THE ROAD AND THEN DROVE TO HARDY FAMILY FORD (1255 MARIETTA HWY, DALLAS, GA 30157) WHERE IT WAS DIAGNOSED THAT THE TRANSMISSION NEEDED TO BE REPLACED. THE CONTACT RECEIVED A RECALL NOTIFICATION FOR NHTSA CAMPAIGN NUMBER: 19V075000 (POWER TRAIN). THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC AND REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 150,000.
MY TRANSMISSION WAS SHIFTING OUT OF 6TH GEAR INTO 1ST GEAR. THIS WAS UPDATED BY A COMPUTER FIX THAT KEEPS IT FROM SHIFTING TO 1ST GEAR BUT INTO 5TH INSTEAD. FORD HAS A CUSTOMER SATISFACTION PROGRAM 16N02 THAT ADDRESSES THE SAME PROBLEMS I AM HAVING AND A FIX FOR IT. MY TRUCK WAS BUILT AT THE PLANT INDICATED, IN THE TIME FRAME…
Read full complaint
MY TRANSMISSION WAS SHIFTING OUT OF 6TH GEAR INTO 1ST GEAR. THIS WAS UPDATED BY A COMPUTER FIX THAT KEEPS IT FROM SHIFTING TO 1ST GEAR BUT INTO 5TH INSTEAD. FORD HAS A CUSTOMER SATISFACTION PROGRAM 16N02 THAT ADDRESSES THE SAME PROBLEMS I AM HAVING AND A FIX FOR IT. MY TRUCK WAS BUILT AT THE PLANT INDICATED, IN THE TIME FRAME INDICATED AND GIVES THE ENGINE CODES AS INDICATED BY THE BULLETIN. I HAVE CONTACTED THEM ABOUT IT AND DESPITE ALL THESE FINDINGS AM BEING TOLD THAT IT IS NOT THEIR PROBLEM TO FIX. MY MILEAGE IS BELOW THE 150K THRESHOLD THAT IS SET FOR THIS WARRANTY EXTENSION ON THE LEAD FRAME PROBLEM. THEIR FIX TO STOP IT FROM SHIFTING TO 1ST GEAR REDUCES THE CHANCE FOR A MAJOR ACCIDENT BUT THEIR REFUSAL TO FIX THE PROBLEM IN THE LEAD FRAME STILL LEAVES THIS AS A SAFETY ISSUE. A DOWN SHIFT AT SPEED TO 5TH GEAR STILL CAUSES AN UNINDICATED AND UNCONTROLLED SLOW DOWN OF MY TRUCK, THE LOSS OF SPEEDOMETER IS ALSO APPARENTLY CAUSING SOME PROBLEM WITH THE PASSENGER SIDE AIRBAG WHEN THIS OCCURS AS I MA GETTING A MESSAGE TO REMOVE OBJECTS FROM THE PASSENGER SEAT WHEN THIS OCCURS. MY LOCAL FORD SHOP WILL NOT TRY TO WARRANTY THIS PROBLEM, I HAVE MADE 2 DIFFERENT CONTACTS AT FORD CONCERNING THIS AND THEY ALL SAY IT IS NOT ONE THEY HAVE MARKED FOR HAVING THIS PROBLEM. I CAN'T HELP THAT IT IS NOT ONE THEY THOUGHT MIGHT BE AFFECTED, I CAN ONLY SAY THAT IT HAS BEEN AND CAN'T GET IT REPAIRED BY THEM.
TL* THE CONTACT OWNS A 2012 FORD F-150. WHILE DRIVING BETWEEN 30-50 MPH, THE GEAR SHIFTER SWITCHED INTO NEUTRAL AND CAUSED THE ENGINE TO REV. THE FAILURE EVENTUALLY CAUSED THE VEHICLE TO LOSE POWER. THE VEHICLE WAS TAKEN TO SALINAS VALLEY FORD LINCOLN (1100 AUTO CENTER CIR, SALINAS, CA 93907) WHERE IT WAS DIAGNOSED THAT THE TRAN…
Read full complaint
TL* THE CONTACT OWNS A 2012 FORD F-150. WHILE DRIVING BETWEEN 30-50 MPH, THE GEAR SHIFTER SWITCHED INTO NEUTRAL AND CAUSED THE ENGINE TO REV. THE FAILURE EVENTUALLY CAUSED THE VEHICLE TO LOSE POWER. THE VEHICLE WAS TAKEN TO SALINAS VALLEY FORD LINCOLN (1100 AUTO CENTER CIR, SALINAS, CA 93907) WHERE IT WAS DIAGNOSED THAT THE TRANSMISSION CONTROL MODULE NEEDED TO BE REPLACED. THE MANUFACTURER WAS NOTIFIED AND DID NOT ASSIST. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 52,000.
I RECEIVED WRITTEN NOTICE FROM FORD THAT OUR 2012 YEAR MODEL, FORD, F-150 PICKUP TRUCK WAS RECALLED UNDER FORD RECALL: 19S07 AND NHTSA RECALL: 19V-075. THIS IS THE RECALL HAVING TO DO WITH FORDS PCM PROGRAMMING BEING UNABLE TO COPE WITH AN INTERMITTENT FAILURE OF THE TRANSMISSION OSS. THE PCM WOULD FORCE THE VEHICLE INTO 1ST G…
Read full complaint
I RECEIVED WRITTEN NOTICE FROM FORD THAT OUR 2012 YEAR MODEL, FORD, F-150 PICKUP TRUCK WAS RECALLED UNDER FORD RECALL: 19S07 AND NHTSA RECALL: 19V-075. THIS IS THE RECALL HAVING TO DO WITH FORDS PCM PROGRAMMING BEING UNABLE TO COPE WITH AN INTERMITTENT FAILURE OF THE TRANSMISSION OSS. THE PCM WOULD FORCE THE VEHICLE INTO 1ST GEAR REGARDLESS OF CURRENT OPERATING SPEED (MPH). I WAS JUST INFORMED BY A LOCAL FORD DEALERSHIP THAT FORD CANNOT PERFORM A FIX ON MY VEHICLE BECAUSE THEY ONLY REPAIRED THE PCM FOR THE V8 ENGINE AND HAVE NOT YET GOTTEN AROUND TO THE V6 ECO BOOST ENGINES, EVEN THOUGH THE RECALL DOCUMENTS I RECEIVED INSTRUCT ME TO TAKE THE TRUCK IN FOR THE RECALL REPAIR. FURTHER, THE RECALL DOCUMENTS I RECEIVED HAVE THE VEHICLE INFO (VIN INCLUDED) ON EACH OF THEM SO ONE WOULD ASSUME THE VIN WAS CROSSCHECKED WITH FORD'S MANUFACTURING DATA BASE TO DETERMINE IF THE OFFERED FIX ACTUALLY FIT THE VEHICLE. I AM TOLD THAT OUR VEHICLE DOES NEED THE FIX BUT IT WILL NOT BE OUT UNTIL SOME TIME LATER THIS SUMMER.
TL* THE CONTACT OWNS A 2012 FORD F-150. WHILE DRIVING VARIOUS SPEEDS, THE VEHICLE DOWNSHIFTED INTO FIRST GEAR INDEPENDENTLY. THE FAILURE OCCURRED INTERMITTENTLY. THE CONTACT HAD TO PULL THE VEHICLE OVER TO REGAIN CONTROL. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V075000 (POWER TRAIN). THE CONTACT STATED THAT…
Read full complaint
TL* THE CONTACT OWNS A 2012 FORD F-150. WHILE DRIVING VARIOUS SPEEDS, THE VEHICLE DOWNSHIFTED INTO FIRST GEAR INDEPENDENTLY. THE FAILURE OCCURRED INTERMITTENTLY. THE CONTACT HAD TO PULL THE VEHICLE OVER TO REGAIN CONTROL. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V075000 (POWER TRAIN). THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. FORD OF LONDONDERRY (33 NASHUA RD, LONDONDERRY, NH 03053, (603) 434-4141) WAS CONTACTED AND CONFIRMED THAT THE PARTS WERE NOT AVAILABLE FOR THE RECALL REMEDY. THE MANUFACTURER WAS NOTIFIED. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS 65,000. PARTS DISTRIBUTION DISCONNECT.
I EXPERIENCED A SUDDEN SHIFT INTO 1ST GEAR AND A BLUE WRENCH COME ON THE DASHBOARD WHILE GOING 65 DOWN THE HIGHWAY. THIS OF COURSE WAS NOT SAFE AND I WAS ABLE TO CONTROL VEHICLE AND STOP IT. SHUT THE VEHICLE OFF AND TURNED IT BACK ON AND ABLE TO FINISH MY DRIVE. AFTER THIS HAPPENED 2 MORE TIMES, I CONTACTED DEALERSHIP TO SEE…
Read full complaint
I EXPERIENCED A SUDDEN SHIFT INTO 1ST GEAR AND A BLUE WRENCH COME ON THE DASHBOARD WHILE GOING 65 DOWN THE HIGHWAY. THIS OF COURSE WAS NOT SAFE AND I WAS ABLE TO CONTROL VEHICLE AND STOP IT. SHUT THE VEHICLE OFF AND TURNED IT BACK ON AND ABLE TO FINISH MY DRIVE. AFTER THIS HAPPENED 2 MORE TIMES, I CONTACTED DEALERSHIP TO SEE IF THERE WERE ANY KNOWN ISSUES. LOOKING AT MY VIN THEY SAID THERE WAS NOT. SO I TOOK TO MY MECHANIC AND THEY REPALCED THE OSS AND LEAD WIRES TO THE TRANSMISSION.
Official recalls
419V075000 · Power Train:automatic Transmission; Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
Feb 11, 2019
Ford Motor Company (Ford) is recalling certain 2011-2013 F-150 vehicles equipped with a 6-speed automatic transmission. The transmission may unexpectedly downshift into first gear, regardless of vehicle speed.
Consequence & remedy
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began March 4, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S07.
Additional source detail variants (2)
Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
Ford Motor Company (Ford) is recalling certain 2011-2013 F-150 vehicles equipped with a 6-speed automatic transmission. The transmission may unexpectedly downshift into first gear, regardless of vehicle speed.
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began March 4, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S07.
Power Train:automatic Transmission
Ford Motor Company (Ford) is recalling certain 2011-2013 F-150 vehicles equipped with a 6-speed automatic transmission. The transmission may unexpectedly downshift into first gear, regardless of vehicle speed.
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began March 4, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S07.
16V248000 · Power Train:automatic Transmission
Apr 27, 2016
Ford Motor Company (Ford) is recalling certain model year 2011-2012 Ford F-150 trucks, 2012 Ford Expedition, Lincoln Navigator, and Ford Mustang vehicles. The affected vehicles are equipped with an automatic transmission that may unexpectedly downshift to first gear, regardless of vehicle speed.
Consequence & remedy
Consequence: An unexpected downshift into first gear can cause the vehicle to slow down suddenly without warning and the rear tires may slide or lock, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module with updated software, free of charge. The recall began on September 19, 2016. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S19.
12V190000 · Exterior Lighting:back Up Lights; Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
May 3, 2012
FORD IS RECALLING CERTAIN MODEL YEAR 2011-2012 FORD F-150, 2012 EXPEDITION AND LINCOLN NAVIGATOR, AND 2012-2013 MUSTANG VEHICLES, FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 102, "TRANSMISSION SHIFT LEVER SEQUENCE, STARTER INTERLOCK, AND TRANSMISSION BRAKING EFFECT" AND 108 LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT. THESE VEHICLES MAY HAVE A TRANSMISSION RANGE SENSOR (TRS) THAT WAS CALIBRATED OUT OF SPECIFICATION FOR REVERSE GEAR.
Consequence & remedy
Consequence: IF THIS CONDITION EXISTS, THE TRANSMISSION MAY NOT GO INTO REVERSE OR WHEN THE DRIVER PUSHES THE SHIFT LEVER IN THE REVERSE R POSITION AND THE VEHICLES TRANSMISSION DOES GO IN REVERSE, THE R MAY NOT ILLUMINATE ON THE DASHBOARD OF THE F-150, EXPEDITION, OR NAVIGATOR MODELS AND/OR THE BACKUP LAMP ON THE REAR OF THE F-150, EXPEDITION, NAVIGATOR, OR MUSTANG VEHICLES MAY NOT ILLUMINATE. THESE CONDITIONS INCREASE THE RISK OF A CRASH OR A PEDESTRIAN BEING STRUCK DUE TO THE VEHICLES NOT SIGNALING IT IS IN REVERSE.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT AND REPLACE THE TRS AS NECESSARY, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 11, 2012. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
Additional source detail variants (2)
Exterior Lighting:back Up Lights
FORD IS RECALLING CERTAIN MODEL YEAR 2011-2012 FORD F-150, 2012 EXPEDITION AND LINCOLN NAVIGATOR, AND 2012-2013 MUSTANG VEHICLES, FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 102, "TRANSMISSION SHIFT LEVER SEQUENCE, STARTER INTERLOCK, AND TRANSMISSION BRAKING EFFECT" AND 108 LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT. THESE VEHICLES MAY HAVE A TRANSMISSION RANGE SENSOR (TRS) THAT WAS CALIBRATED OUT OF SPECIFICATION FOR REVERSE GEAR.
Consequence: IF THIS CONDITION EXISTS, THE TRANSMISSION MAY NOT GO INTO REVERSE OR WHEN THE DRIVER PUSHES THE SHIFT LEVER IN THE REVERSE R POSITION AND THE VEHICLES TRANSMISSION DOES GO IN REVERSE, THE R MAY NOT ILLUMINATE ON THE DASHBOARD OF THE F-150, EXPEDITION, OR NAVIGATOR MODELS AND/OR THE BACKUP LAMP ON THE REAR OF THE F-150, EXPEDITION, NAVIGATOR, OR MUSTANG VEHICLES MAY NOT ILLUMINATE. THESE CONDITIONS INCREASE THE RISK OF A CRASH OR A PEDESTRIAN BEING STRUCK DUE TO THE VEHICLES NOT SIGNALING IT IS IN REVERSE.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT AND REPLACE THE TRS AS NECESSARY, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 11, 2012. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
FORD IS RECALLING CERTAIN MODEL YEAR 2011-2012 FORD F-150, 2012 EXPEDITION AND LINCOLN NAVIGATOR, AND 2012-2013 MUSTANG VEHICLES, FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 102, "TRANSMISSION SHIFT LEVER SEQUENCE, STARTER INTERLOCK, AND TRANSMISSION BRAKING EFFECT" AND 108 LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT. THESE VEHICLES MAY HAVE A TRANSMISSION RANGE SENSOR (TRS) THAT WAS CALIBRATED OUT OF SPECIFICATION FOR REVERSE GEAR.
Consequence: IF THIS CONDITION EXISTS, THE TRANSMISSION MAY NOT GO INTO REVERSE OR WHEN THE DRIVER PUSHES THE SHIFT LEVER IN THE REVERSE R POSITION AND THE VEHICLES TRANSMISSION DOES GO IN REVERSE, THE R MAY NOT ILLUMINATE ON THE DASHBOARD OF THE F-150, EXPEDITION, OR NAVIGATOR MODELS AND/OR THE BACKUP LAMP ON THE REAR OF THE F-150, EXPEDITION, NAVIGATOR, OR MUSTANG VEHICLES MAY NOT ILLUMINATE. THESE CONDITIONS INCREASE THE RISK OF A CRASH OR A PEDESTRIAN BEING STRUCK DUE TO THE VEHICLES NOT SIGNALING IT IS IN REVERSE.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT AND REPLACE THE TRS AS NECESSARY, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 11, 2012. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
12V198000 · Air Bags:frontal:sensor/control MODULE-INACTIVE
May 3, 2012
FORD IS RECALLING CERTAIN MODEL YEAR 2012 F-150 VEHICLES MANUFACTURED FROM NOVEMBER 6, 2011, THROUGH NOVEMBER 15, 2011. INCORRECT SOFTWARE FOR THE OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) WAS INSTALLED ON THE VEHICLES EITHER AT THE TIME OF MANUFACTURING OR DURING THE COURSE OF REPLACEMENT OF THE MODULE AS PART OF A SERVICE REPAIR. UNDER CERTAIN DRIVING CONDITIONS, THE OCSM MAY MISCLASSIFY THE PASSENGER SEATS OCCUPANT SUCH THAT THE PASSENGER SIDE AIRBAG DOES NOT DEPLOY WHEN IT SHOULD, DOES NOT DEPLOY AS INTENDED, OR DEPLOYS WHEN IT SHOULD NOT.
Consequence & remedy
Consequence: A FAILURE TO DEPLOY, FAILURE TO DEPLOY AS INTENDED, OR A DEPLOYMENT WHEN NOT INTENDED, INCREASES THE RISK OF INJURY TO THE PASSENGER SIDE SEAT OCCUPANT.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE OCSM FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 21, 2012. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4RQ17010 · Unexpected Transmission Downshift
Opened Dec 25, 2017 · Closed Oct 22, 2019
Status: closed (inferred from source dates) · Power Train:automatic Transmission; Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of transmissions unexpectedly downshifting to a lower gear without input from the driver on model year (MY) 2011-2013 Ford F-150, Expedition and Navigator vehicles. ODI has received 455 unique reports related to the alleged problem that were not covered under a previous recall for this issue (16V-248).Expedition and Navigator complaint rates are lower than F-150 complaints. Of those 455 reports, 34.7% claimed that the rear wheels locked up when the transmission downshifted. There were 4 accident claims with no injuries. There are many instances where drivers report leaving their lane or the road because of this issue.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 783 unique reports related to the alleged problem. There were 6 accident claims with 3 injuries. Ford also submitted 1206 warranty claims related to transmission downshifting failures. The failure can occur at any time, but typically at higher speed, and include symptoms such as sudden transmission downshifting, loss of speedometer, erratic shifting of transmission, and transmission stuck in one gear. The failures typically occur without warning and may result in the rear wheels momentarily locking up. The driver often had to fully stop the vehicle and restart it to get the vehicle to shift properly.On February 2nd, 2019 Ford notified ODI that it would conduct a safety recall (19V-075) to remedy transmission downshifting failures on all 2011-2013 F-150 vehicles. Ford will also offer extended warranties to 2011-2013 Expedition and Navigator vehicles with the same issue. Per Ford, some vehicles may experience an intermittent loss of Transmission Output Speed Sensor (OSS) signal to the Powertrain Control Module (PCM), potentially resulting in a temporary unintended downshift into first gear. Ford will reprogram the PCM with software that will prevent an unintended downshift into first gear and illuminate the Malfunction Indicator Light in the event of an intermittent OSS signal loss.The recall action initiated by the manufacturer appears to address the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the identification (ODI) numbers found in the attached list.
Additional source detail variants (2)
Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of transmissions unexpectedly downshifting to a lower gear without input from the driver on model year (MY) 2011-2013 Ford F-150, Expedition and Navigator vehicles. ODI has received 455 unique reports related to the alleged problem that were not covered under a previous recall for this issue (16V-248).Expedition and Navigator complaint rates are lower than F-150 complaints. Of those 455 reports, 34.7% claimed that the rear wheels locked up when the transmission downshifted. There were 4 accident claims with no injuries. There are many instances where drivers report leaving their lane or the road because of this issue.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 783 unique reports related to the alleged problem. There were 6 accident claims with 3 injuries. Ford also submitted 1206 warranty claims related to transmission downshifting failures. The failure can occur at any time, but typically at higher speed, and include symptoms such as sudden transmission downshifting, loss of speedometer, erratic shifting of transmission, and transmission stuck in one gear. The failures typically occur without warning and may result in the rear wheels momentarily locking up. The driver often had to fully stop the vehicle and restart it to get the vehicle to shift properly.On February 2nd, 2019 Ford notified ODI that it would conduct a safety recall (19V-075) to remedy transmission downshifting failures on all 2011-2013 F-150 vehicles. Ford will also offer extended warranties to 2011-2013 Expedition and Navigator vehicles with the same issue. Per Ford, some vehicles may experience an intermittent loss of Transmission Output Speed Sensor (OSS) signal to the Powertrain Control Module (PCM), potentially resulting in a temporary unintended downshift into first gear. Ford will reprogram the PCM with software that will prevent an unintended downshift into first gear and illuminate the Malfunction Indicator Light in the event of an intermittent OSS signal loss.The recall action initiated by the manufacturer appears to address the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the identification (ODI) numbers found in the attached list.
Power Train:automatic Transmission
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of transmissions unexpectedly downshifting to a lower gear without input from the driver on model year (MY) 2011-2013 Ford F-150, Expedition and Navigator vehicles. ODI has received 455 unique reports related to the alleged problem that were not covered under a previous recall for this issue (16V-248).Expedition and Navigator complaint rates are lower than F-150 complaints. Of those 455 reports, 34.7% claimed that the rear wheels locked up when the transmission downshifted. There were 4 accident claims with no injuries. There are many instances where drivers report leaving their lane or the road because of this issue.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 783 unique reports related to the alleged problem. There were 6 accident claims with 3 injuries. Ford also submitted 1206 warranty claims related to transmission downshifting failures. The failure can occur at any time, but typically at higher speed, and include symptoms such as sudden transmission downshifting, loss of speedometer, erratic shifting of transmission, and transmission stuck in one gear. The failures typically occur without warning and may result in the rear wheels momentarily locking up. The driver often had to fully stop the vehicle and restart it to get the vehicle to shift properly.On February 2nd, 2019 Ford notified ODI that it would conduct a safety recall (19V-075) to remedy transmission downshifting failures on all 2011-2013 F-150 vehicles. Ford will also offer extended warranties to 2011-2013 Expedition and Navigator vehicles with the same issue. Per Ford, some vehicles may experience an intermittent loss of Transmission Output Speed Sensor (OSS) signal to the Powertrain Control Module (PCM), potentially resulting in a temporary unintended downshift into first gear. Ford will reprogram the PCM with software that will prevent an unintended downshift into first gear and illuminate the Malfunction Indicator Light in the event of an intermittent OSS signal loss.The recall action initiated by the manufacturer appears to address the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the identification (ODI) numbers found in the attached list.
EA15006 · Brake Vacuum Pump Failure
Opened Oct 16, 2015 · Closed Apr 28, 2016
Status: closed (inferred from source dates) · Service Brakes, Electric; Service Brakes, Hydraulic:power Assist; Service Brakes, Hydraulic:power Assist:vacuum
On February 15, 2016, Ford Motor Company initiated Customer Satisfaction Program 15N05 to extend warranty coverage for the electric vacuum pump in certain model year (MY) 2011 through 2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines.The program extends coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through July 30, 2016 regardless of mileage.Ford's program covers all repairs related to electric vacuum pump (EVP) malfunctions including excessive noise, vibration, or change in brake pedal feel while applying the brakes at cold start. Ford states that the engine intake manifold is the primary source of vacuum for the brake booster and is fully compliant to motor vehicle safety standards without the supplemental vacuum supplied by the EVP.The company also contends that failure modes related to the EVP are progressive and provide warning to operators by way of noise and vibration before an operator to experience any temporary change in brake pedal feel.ODI's analysis of warranty data found that the majority of claims involved consumer concerns with EVP noise or vibration from the left front fender area when the vehicle is first started. Continued operation in this mode with pump motor noise will eventually result in the EVP seizing or becoming non-functional.Component failure analysis indicated that Ford and its supplier, Continental, identified a pump crank drive corrosion condition due to moisture entry through the vacuum intake.Corrosion damage to EVP internal components may eventually result in a blown fuse in the power distribution box and total loss of EVP function.Analysis of consumer complaints, field reports, and warranty data related to EVP failures found thatincidents predominantly occurred in driveways and parking lots in the periods immediately after cold engine starts.Many consumers operated their vehicle for some period of time with a blown EVP fuse without realizing that the pump had failed or that the vehicle had a brake system malfunction.Consumers who did experience braking performance issues reporteda temporary hard brake pedal condition at start-up followed by more consistent normal pedal feel after few seconds.On June 22, 2015, Ford developed a remedy procedure and issued TSB 15-0105 instructing dealers to replace the vacuum pump and install a new vacuum pump harness kit. In addition to reviewing test data submitted by Ford, ODI assessed safety risks associated with the alleged defect under various operating conditions, including: 1) baseline system performance with full engine and EVP vacuum available using exemplar parts, 2) disabled EVP and booster vacuum regulated to simulate worst case conditions for engine intake manifold vacuum supply to the brake booster (approximately 300 mbar); and 3) all source vacuum to the brake booster removed and Optimized Hydraulic Braking (OHB) mode active to represent complete loss of brake booster function (note: this condition is a more severe brake boost system failure mode than the alleged defect).ODI also analyzed all complaints and warranty claims to identify incidents alleging brake system performance concerns related to EVP failures.These analyses identified no brake performance issues or resulting changes in stopping distances either on highway or city traffic conditions.Two complaints alleging EVP malfunctions caused or contributed to rear-end collisions during attempted decelerations from road speeds are not believed to be related to the alleged defect.The EVP provides supplemental vacuum during initial start-up and idle
Additional source detail variants (3)
Service Brakes, Electric
On February 15, 2016, Ford Motor Company initiated Customer Satisfaction Program 15N05 to extend warranty coverage for the electric vacuum pump in certain model year (MY) 2011 through 2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines.The program extends coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through July 30, 2016 regardless of mileage.Ford's program covers all repairs related to electric vacuum pump (EVP) malfunctions including excessive noise, vibration, or change in brake pedal feel while applying the brakes at cold start. Ford states that the engine intake manifold is the primary source of vacuum for the brake booster and is fully compliant to motor vehicle safety standards without the supplemental vacuum supplied by the EVP.The company also contends that failure modes related to the EVP are progressive and provide warning to operators by way of noise and vibration before an operator to experience any temporary change in brake pedal feel.ODI's analysis of warranty data found that the majority of claims involved consumer concerns with EVP noise or vibration from the left front fender area when the vehicle is first started. Continued operation in this mode with pump motor noise will eventually result in the EVP seizing or becoming non-functional.Component failure analysis indicated that Ford and its supplier, Continental, identified a pump crank drive corrosion condition due to moisture entry through the vacuum intake.Corrosion damage to EVP internal components may eventually result in a blown fuse in the power distribution box and total loss of EVP function.Analysis of consumer complaints, field reports, and warranty data related to EVP failures found thatincidents predominantly occurred in driveways and parking lots in the periods immediately after cold engine starts.Many consumers operated their vehicle for some period of time with a blown EVP fuse without realizing that the pump had failed or that the vehicle had a brake system malfunction.Consumers who did experience braking performance issues reporteda temporary hard brake pedal condition at start-up followed by more consistent normal pedal feel after few seconds.On June 22, 2015, Ford developed a remedy procedure and issued TSB 15-0105 instructing dealers to replace the vacuum pump and install a new vacuum pump harness kit. In addition to reviewing test data submitted by Ford, ODI assessed safety risks associated with the alleged defect under various operating conditions, including: 1) baseline system performance with full engine and EVP vacuum available using exemplar parts, 2) disabled EVP and booster vacuum regulated to simulate worst case conditions for engine intake manifold vacuum supply to the brake booster (approximately 300 mbar); and 3) all source vacuum to the brake booster removed and Optimized Hydraulic Braking (OHB) mode active to represent complete loss of brake booster function (note: this condition is a more severe brake boost system failure mode than the alleged defect).ODI also analyzed all complaints and warranty claims to identify incidents alleging brake system performance concerns related to EVP failures.These analyses identified no brake performance issues or resulting changes in stopping distances either on highway or city traffic conditions.Two complaints alleging EVP malfunctions caused or contributed to rear-end collisions during attempted decelerations from road speeds are not believed to be related to the alleged defect.The EVP provides supplemental vacuum during initial start-up and idle
Service Brakes, Hydraulic:power Assist
On February 15, 2016, Ford Motor Company initiated Customer Satisfaction Program 15N05 to extend warranty coverage for the electric vacuum pump in certain model year (MY) 2011 through 2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines.The program extends coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through July 30, 2016 regardless of mileage.Ford's program covers all repairs related to electric vacuum pump (EVP) malfunctions including excessive noise, vibration, or change in brake pedal feel while applying the brakes at cold start. Ford states that the engine intake manifold is the primary source of vacuum for the brake booster and is fully compliant to motor vehicle safety standards without the supplemental vacuum supplied by the EVP.The company also contends that failure modes related to the EVP are progressive and provide warning to operators by way of noise and vibration before an operator to experience any temporary change in brake pedal feel.ODI's analysis of warranty data found that the majority of claims involved consumer concerns with EVP noise or vibration from the left front fender area when the vehicle is first started. Continued operation in this mode with pump motor noise will eventually result in the EVP seizing or becoming non-functional.Component failure analysis indicated that Ford and its supplier, Continental, identified a pump crank drive corrosion condition due to moisture entry through the vacuum intake.Corrosion damage to EVP internal components may eventually result in a blown fuse in the power distribution box and total loss of EVP function.Analysis of consumer complaints, field reports, and warranty data related to EVP failures found thatincidents predominantly occurred in driveways and parking lots in the periods immediately after cold engine starts.Many consumers operated their vehicle for some period of time with a blown EVP fuse without realizing that the pump had failed or that the vehicle had a brake system malfunction.Consumers who did experience braking performance issues reporteda temporary hard brake pedal condition at start-up followed by more consistent normal pedal feel after few seconds.On June 22, 2015, Ford developed a remedy procedure and issued TSB 15-0105 instructing dealers to replace the vacuum pump and install a new vacuum pump harness kit. In addition to reviewing test data submitted by Ford, ODI assessed safety risks associated with the alleged defect under various operating conditions, including: 1) baseline system performance with full engine and EVP vacuum available using exemplar parts, 2) disabled EVP and booster vacuum regulated to simulate worst case conditions for engine intake manifold vacuum supply to the brake booster (approximately 300 mbar); and 3) all source vacuum to the brake booster removed and Optimized Hydraulic Braking (OHB) mode active to represent complete loss of brake booster function (note: this condition is a more severe brake boost system failure mode than the alleged defect).ODI also analyzed all complaints and warranty claims to identify incidents alleging brake system performance concerns related to EVP failures.These analyses identified no brake performance issues or resulting changes in stopping distances either on highway or city traffic conditions.Two complaints alleging EVP malfunctions caused or contributed to rear-end collisions during attempted decelerations from road speeds are not believed to be related to the alleged defect.The EVP provides supplemental vacuum during initial start-up and idle
Service Brakes, Hydraulic:power Assist:vacuum
On February 15, 2016, Ford Motor Company initiated Customer Satisfaction Program 15N05 to extend warranty coverage for the electric vacuum pump in certain model year (MY) 2011 through 2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines.The program extends coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through July 30, 2016 regardless of mileage.Ford's program covers all repairs related to electric vacuum pump (EVP) malfunctions including excessive noise, vibration, or change in brake pedal feel while applying the brakes at cold start. Ford states that the engine intake manifold is the primary source of vacuum for the brake booster and is fully compliant to motor vehicle safety standards without the supplemental vacuum supplied by the EVP.The company also contends that failure modes related to the EVP are progressive and provide warning to operators by way of noise and vibration before an operator to experience any temporary change in brake pedal feel.ODI's analysis of warranty data found that the majority of claims involved consumer concerns with EVP noise or vibration from the left front fender area when the vehicle is first started. Continued operation in this mode with pump motor noise will eventually result in the EVP seizing or becoming non-functional.Component failure analysis indicated that Ford and its supplier, Continental, identified a pump crank drive corrosion condition due to moisture entry through the vacuum intake.Corrosion damage to EVP internal components may eventually result in a blown fuse in the power distribution box and total loss of EVP function.Analysis of consumer complaints, field reports, and warranty data related to EVP failures found thatincidents predominantly occurred in driveways and parking lots in the periods immediately after cold engine starts.Many consumers operated their vehicle for some period of time with a blown EVP fuse without realizing that the pump had failed or that the vehicle had a brake system malfunction.Consumers who did experience braking performance issues reporteda temporary hard brake pedal condition at start-up followed by more consistent normal pedal feel after few seconds.On June 22, 2015, Ford developed a remedy procedure and issued TSB 15-0105 instructing dealers to replace the vacuum pump and install a new vacuum pump harness kit. In addition to reviewing test data submitted by Ford, ODI assessed safety risks associated with the alleged defect under various operating conditions, including: 1) baseline system performance with full engine and EVP vacuum available using exemplar parts, 2) disabled EVP and booster vacuum regulated to simulate worst case conditions for engine intake manifold vacuum supply to the brake booster (approximately 300 mbar); and 3) all source vacuum to the brake booster removed and Optimized Hydraulic Braking (OHB) mode active to represent complete loss of brake booster function (note: this condition is a more severe brake boost system failure mode than the alleged defect).ODI also analyzed all complaints and warranty claims to identify incidents alleging brake system performance concerns related to EVP failures.These analyses identified no brake performance issues or resulting changes in stopping distances either on highway or city traffic conditions.Two complaints alleging EVP malfunctions caused or contributed to rear-end collisions during attempted decelerations from road speeds are not believed to be related to the alleged defect.The EVP provides supplemental vacuum during initial start-up and idle
PE15026 · Brake Vacuum Pump Failure
Opened Jun 22, 2015 · Closed Oct 19, 2015
Status: closed (inferred from source dates) · Service Brakes, Electric; Service Brakes, Hydraulic:power Assist; Service Brakes, Hydraulic:power Assist:vacuum
On June 22, 2015, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE15-026 to investigate incidents of increased brake pedal effort at cold start and extended stopping distance while driving in traffic, resulting from failures of the electric brake vacuum assist pump in model year (MY) 2011-2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines. In response to ODI's Information Request (IR) for PE15-026, Ford provided ODI with 396 complaints and field reports relating to incidents of increased brake pedal effort or malfunctions in the electric vacuum pump (EVP). ODI's analysis of the data provided by Ford identified 7 crashes and 1,851 warranty claims related to either a hard brake pedal condition or reduced brake effectiveness. Additionally, ODI identified one report in its database alleging an injury to an occupant of a vehicle struck in the rear by a subject F-150 vehicle with a failed EVP as documented in the police accident report referencing a dealer assessment of the pump.According to Ford, the subject vehicles utilize a traditional brake vacuum booster to provide power assist for braking and the EVP is intended to operate to maintain consistent brake pedal feel. The engine intake manifold is the primary source of vacuum for the booster and is fully compliant to motor vehicle safety standards without the EVP. Ford described the conditions related to a change in brake pedal feel as limited and temporary and provided component failure analysis showing evidence of water entry into the EVP which caused internal pump corrosion. Ford indicated that the EVP failure mode is progressive and provides warning to operators by way of noise and vibration before an operator is likely to experience any temporary change in brake pedal feel. Damage to the EVP motor bearing may eventually result in a blown EVP fuse and total loss of EVP function. Ford provided test data showing the brake pedal forces and pedal travel curves over time for 0.3g decelerations to a stop from 80kph (50mph) for: 1) normal system (full engine and EVP vacuum available); 2) Ford's approximation of worst case booster performance with EVP failure (EVP disabled and booster vacuum regulated to 300mbar to simulate cold start, all accessory loads on, and starting at 0 vacuum); and 3) with all source vacuum to the brake booster removed and Hydraulic Boost Compensation (HBC) active to represent complete loss of brake booster function. The Ford tests showed that the brake pedal forces required for achieving the 0.3g decelerations were relatively low for the normal condition, 35-40 N (8-9 lbf), increased by approximately 2-3 times normal when the EVP is disabled, 75-115 N (17-26 lbf), and increased by about 5-6 times normal for the complete brake booster failure condition, 205-215 N (46-48 lbf). This Preliminary Evaluation has been upgraded to Engineering Analysis (EA15-006) to test for EVP malfunctions under other vehicle operating conditions (e.g., low-speed driveway braking after cold-start with failed EVP), potential human factors contributions and to further assess the scope, frequency, and safety-related consequences of the alleged defect.The VOQs associated with the opening of this investigation are:10565994, 10575987, 10598351, 10604687, 10605701, 10607811, 10610491, 10615536, 10617828, 10619545, 10643075, 10650578, 10662151, 10664415, 10666988, 10668069, 10678844, 10695537, 10700874, 10706217, 10706271, 10712465, 10723033, 10723792, 10726960, 10730549, 10730721, 10730735, 10730837, 10730909, 10731008, 10731135, 10731157, 10731165, 10731395, 10731758, 10732609, 10732878, 10733375, 10733804, 10734558, 10734613, 10743859, 10744214, 10
Additional source detail variants (3)
Service Brakes, Electric
On June 22, 2015, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE15-026 to investigate incidents of increased brake pedal effort at cold start and extended stopping distance while driving in traffic, resulting from failures of the electric brake vacuum assist pump in model year (MY) 2011-2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines. In response to ODI's Information Request (IR) for PE15-026, Ford provided ODI with 396 complaints and field reports relating to incidents of increased brake pedal effort or malfunctions in the electric vacuum pump (EVP). ODI's analysis of the data provided by Ford identified 7 crashes and 1,851 warranty claims related to either a hard brake pedal condition or reduced brake effectiveness. Additionally, ODI identified one report in its database alleging an injury to an occupant of a vehicle struck in the rear by a subject F-150 vehicle with a failed EVP as documented in the police accident report referencing a dealer assessment of the pump.According to Ford, the subject vehicles utilize a traditional brake vacuum booster to provide power assist for braking and the EVP is intended to operate to maintain consistent brake pedal feel. The engine intake manifold is the primary source of vacuum for the booster and is fully compliant to motor vehicle safety standards without the EVP. Ford described the conditions related to a change in brake pedal feel as limited and temporary and provided component failure analysis showing evidence of water entry into the EVP which caused internal pump corrosion. Ford indicated that the EVP failure mode is progressive and provides warning to operators by way of noise and vibration before an operator is likely to experience any temporary change in brake pedal feel. Damage to the EVP motor bearing may eventually result in a blown EVP fuse and total loss of EVP function. Ford provided test data showing the brake pedal forces and pedal travel curves over time for 0.3g decelerations to a stop from 80kph (50mph) for: 1) normal system (full engine and EVP vacuum available); 2) Ford's approximation of worst case booster performance with EVP failure (EVP disabled and booster vacuum regulated to 300mbar to simulate cold start, all accessory loads on, and starting at 0 vacuum); and 3) with all source vacuum to the brake booster removed and Hydraulic Boost Compensation (HBC) active to represent complete loss of brake booster function. The Ford tests showed that the brake pedal forces required for achieving the 0.3g decelerations were relatively low for the normal condition, 35-40 N (8-9 lbf), increased by approximately 2-3 times normal when the EVP is disabled, 75-115 N (17-26 lbf), and increased by about 5-6 times normal for the complete brake booster failure condition, 205-215 N (46-48 lbf). This Preliminary Evaluation has been upgraded to Engineering Analysis (EA15-006) to test for EVP malfunctions under other vehicle operating conditions (e.g., low-speed driveway braking after cold-start with failed EVP), potential human factors contributions and to further assess the scope, frequency, and safety-related consequences of the alleged defect.The VOQs associated with the opening of this investigation are:10565994, 10575987, 10598351, 10604687, 10605701, 10607811, 10610491, 10615536, 10617828, 10619545, 10643075, 10650578, 10662151, 10664415, 10666988, 10668069, 10678844, 10695537, 10700874, 10706217, 10706271, 10712465, 10723033, 10723792, 10726960, 10730549, 10730721, 10730735, 10730837, 10730909, 10731008, 10731135, 10731157, 10731165, 10731395, 10731758, 10732609, 10732878, 10733375, 10733804, 10734558, 10734613, 10743859, 10744214, 10
Service Brakes, Hydraulic:power Assist
On June 22, 2015, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE15-026 to investigate incidents of increased brake pedal effort at cold start and extended stopping distance while driving in traffic, resulting from failures of the electric brake vacuum assist pump in model year (MY) 2011-2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines. In response to ODI's Information Request (IR) for PE15-026, Ford provided ODI with 396 complaints and field reports relating to incidents of increased brake pedal effort or malfunctions in the electric vacuum pump (EVP). ODI's analysis of the data provided by Ford identified 7 crashes and 1,851 warranty claims related to either a hard brake pedal condition or reduced brake effectiveness. Additionally, ODI identified one report in its database alleging an injury to an occupant of a vehicle struck in the rear by a subject F-150 vehicle with a failed EVP as documented in the police accident report referencing a dealer assessment of the pump.According to Ford, the subject vehicles utilize a traditional brake vacuum booster to provide power assist for braking and the EVP is intended to operate to maintain consistent brake pedal feel. The engine intake manifold is the primary source of vacuum for the booster and is fully compliant to motor vehicle safety standards without the EVP. Ford described the conditions related to a change in brake pedal feel as limited and temporary and provided component failure analysis showing evidence of water entry into the EVP which caused internal pump corrosion. Ford indicated that the EVP failure mode is progressive and provides warning to operators by way of noise and vibration before an operator is likely to experience any temporary change in brake pedal feel. Damage to the EVP motor bearing may eventually result in a blown EVP fuse and total loss of EVP function. Ford provided test data showing the brake pedal forces and pedal travel curves over time for 0.3g decelerations to a stop from 80kph (50mph) for: 1) normal system (full engine and EVP vacuum available); 2) Ford's approximation of worst case booster performance with EVP failure (EVP disabled and booster vacuum regulated to 300mbar to simulate cold start, all accessory loads on, and starting at 0 vacuum); and 3) with all source vacuum to the brake booster removed and Hydraulic Boost Compensation (HBC) active to represent complete loss of brake booster function. The Ford tests showed that the brake pedal forces required for achieving the 0.3g decelerations were relatively low for the normal condition, 35-40 N (8-9 lbf), increased by approximately 2-3 times normal when the EVP is disabled, 75-115 N (17-26 lbf), and increased by about 5-6 times normal for the complete brake booster failure condition, 205-215 N (46-48 lbf). This Preliminary Evaluation has been upgraded to Engineering Analysis (EA15-006) to test for EVP malfunctions under other vehicle operating conditions (e.g., low-speed driveway braking after cold-start with failed EVP), potential human factors contributions and to further assess the scope, frequency, and safety-related consequences of the alleged defect.The VOQs associated with the opening of this investigation are:10565994, 10575987, 10598351, 10604687, 10605701, 10607811, 10610491, 10615536, 10617828, 10619545, 10643075, 10650578, 10662151, 10664415, 10666988, 10668069, 10678844, 10695537, 10700874, 10706217, 10706271, 10712465, 10723033, 10723792, 10726960, 10730549, 10730721, 10730735, 10730837, 10730909, 10731008, 10731135, 10731157, 10731165, 10731395, 10731758, 10732609, 10732878, 10733375, 10733804, 10734558, 10734613, 10743859, 10744214, 10
Service Brakes, Hydraulic:power Assist:vacuum
On June 22, 2015, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE15-026 to investigate incidents of increased brake pedal effort at cold start and extended stopping distance while driving in traffic, resulting from failures of the electric brake vacuum assist pump in model year (MY) 2011-2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines. In response to ODI's Information Request (IR) for PE15-026, Ford provided ODI with 396 complaints and field reports relating to incidents of increased brake pedal effort or malfunctions in the electric vacuum pump (EVP). ODI's analysis of the data provided by Ford identified 7 crashes and 1,851 warranty claims related to either a hard brake pedal condition or reduced brake effectiveness. Additionally, ODI identified one report in its database alleging an injury to an occupant of a vehicle struck in the rear by a subject F-150 vehicle with a failed EVP as documented in the police accident report referencing a dealer assessment of the pump.According to Ford, the subject vehicles utilize a traditional brake vacuum booster to provide power assist for braking and the EVP is intended to operate to maintain consistent brake pedal feel. The engine intake manifold is the primary source of vacuum for the booster and is fully compliant to motor vehicle safety standards without the EVP. Ford described the conditions related to a change in brake pedal feel as limited and temporary and provided component failure analysis showing evidence of water entry into the EVP which caused internal pump corrosion. Ford indicated that the EVP failure mode is progressive and provides warning to operators by way of noise and vibration before an operator is likely to experience any temporary change in brake pedal feel. Damage to the EVP motor bearing may eventually result in a blown EVP fuse and total loss of EVP function. Ford provided test data showing the brake pedal forces and pedal travel curves over time for 0.3g decelerations to a stop from 80kph (50mph) for: 1) normal system (full engine and EVP vacuum available); 2) Ford's approximation of worst case booster performance with EVP failure (EVP disabled and booster vacuum regulated to 300mbar to simulate cold start, all accessory loads on, and starting at 0 vacuum); and 3) with all source vacuum to the brake booster removed and Hydraulic Boost Compensation (HBC) active to represent complete loss of brake booster function. The Ford tests showed that the brake pedal forces required for achieving the 0.3g decelerations were relatively low for the normal condition, 35-40 N (8-9 lbf), increased by approximately 2-3 times normal when the EVP is disabled, 75-115 N (17-26 lbf), and increased by about 5-6 times normal for the complete brake booster failure condition, 205-215 N (46-48 lbf). This Preliminary Evaluation has been upgraded to Engineering Analysis (EA15-006) to test for EVP malfunctions under other vehicle operating conditions (e.g., low-speed driveway braking after cold-start with failed EVP), potential human factors contributions and to further assess the scope, frequency, and safety-related consequences of the alleged defect.The VOQs associated with the opening of this investigation are:10565994, 10575987, 10598351, 10604687, 10605701, 10607811, 10610491, 10615536, 10617828, 10619545, 10643075, 10650578, 10662151, 10664415, 10666988, 10668069, 10678844, 10695537, 10700874, 10706217, 10706271, 10712465, 10723033, 10723792, 10726960, 10730549, 10730721, 10730735, 10730837, 10730909, 10731008, 10731135, 10731157, 10731165, 10731395, 10731758, 10732609, 10732878, 10733375, 10733804, 10734558, 10734613, 10743859, 10744214, 10
PE13018 · Reduced Power During Hard Acceleration
Opened May 22, 2013 · Closed Apr 7, 2014
Status: closed (inferred from source dates) · Engine; Engine And Engine Cooling
On May 22, 2013, the Office of Defects Investigation (ODI) opened PE13-018 to investigate 95 complaints alleging incidents of reduced engine power during hard accelerations in model year (MY) 2011 through 2013 Ford F-150 trucks.ODI was aware of three technical service bulletins (TSBs) issued by Ford for a condition that was related to moisture accumulation in the Charge Air Cooler (CAC) for the turbochargers.A Preliminary Evaluation was opened to gather information to assess whether the subject vehicles contain a safety related defect.The subject vehicles are powered by Ford?s 3.5L EcoBoost engine which uses twin turbochargers to obtain a balance of fuel economy and engine power based on the driver?s demand.When the driver requests more power from the engine, as in accelerating to pass, merge, ascend hills or haul a load the two turbochargers will spin up compressing the air which is then used to increase the power created by the combustion in the engine.The compressed air, which gains heat by the compression process, is passed through a Charge Air Cooler (CAC) which is designed to lower the temperature of the air in order to make the combustion process even more efficient (Figures 1 and 2).In response to ODI?s Information Request letter, Ford indicated that a misfire condition could occur after steady-speed operation under significantly humid and rainy conditions.Ford?s analysis found that under those conditions, condensation could form and accumulate on the inside of the CAC tubes which could then be ingested into the engine during particularly hard acceleration near wide-open throttle.An engine misfire of up to three cylinders could occur if the amount of condensed water released from the CAC exceeded the engine?s operating threshold for water ingestion.Ford noted that due to regulations set by the EPA, the powertrain software would disable up to two of the misfiring cylinders for no more than 30 seconds and until the driver tips out the throttle in order to protect the catalytic converter from damage. Ford?s testing of this condition on the subject vehicles showed that a vehicle experiencing such a condition would continue to maintain its speed as well as accelerate, albeit at a lower rate than expected by the driver.Similar results were obtained in testing done by NHTSA?s Vehicle Research and Testing Center in East Liberty, Ohio (Figure 6).In an ongoing process to address the problem Ford issued a series of TSBs where a deflector shield was installed onto the CAC (Figures 3, 4 and 5).In January 2014 Ford indicated that its data shows that the TSBs have been effective in resolving the problem, that for the MY 2013 vehicles their remedy is 100% effective and the latest TSBs for MY 2011 ? 2012 are 95% effective.The 525 complaints to ODI and the total 4,120 unique VIN complaints listed in the Failure Report are incidents of alleged reduced power or driveability symptoms and not all are necessarily related to the condition created by water ingestion.Reduced power conditions can occur for a variety of reasons including faults with ignition coils, spark plugs, a catalytic converter, the throttle body, turbocharger, fuel pump/filter, powertrain control module (hardware or software) or transmission shifting problems.Ford also noted that in a large number of warranty claims on the subject vehicles, the CAC was replaced or a TSB procedure was performed when the symptoms exhibited were inconsistent with a CAC water ingestion related issue.Given these circumstances, further use of the agency resources in this matter does not appear to be warranted.Accordingly, this investigation is closed.The closing of
Additional source detail variants (2)
Engine And Engine Cooling
On May 22, 2013, the Office of Defects Investigation (ODI) opened PE13-018 to investigate 95 complaints alleging incidents of reduced engine power during hard accelerations in model year (MY) 2011 through 2013 Ford F-150 trucks.ODI was aware of three technical service bulletins (TSBs) issued by Ford for a condition that was related to moisture accumulation in the Charge Air Cooler (CAC) for the turbochargers.A Preliminary Evaluation was opened to gather information to assess whether the subject vehicles contain a safety related defect.The subject vehicles are powered by Ford?s 3.5L EcoBoost engine which uses twin turbochargers to obtain a balance of fuel economy and engine power based on the driver?s demand.When the driver requests more power from the engine, as in accelerating to pass, merge, ascend hills or haul a load the two turbochargers will spin up compressing the air which is then used to increase the power created by the combustion in the engine.The compressed air, which gains heat by the compression process, is passed through a Charge Air Cooler (CAC) which is designed to lower the temperature of the air in order to make the combustion process even more efficient (Figures 1 and 2).In response to ODI?s Information Request letter, Ford indicated that a misfire condition could occur after steady-speed operation under significantly humid and rainy conditions.Ford?s analysis found that under those conditions, condensation could form and accumulate on the inside of the CAC tubes which could then be ingested into the engine during particularly hard acceleration near wide-open throttle.An engine misfire of up to three cylinders could occur if the amount of condensed water released from the CAC exceeded the engine?s operating threshold for water ingestion.Ford noted that due to regulations set by the EPA, the powertrain software would disable up to two of the misfiring cylinders for no more than 30 seconds and until the driver tips out the throttle in order to protect the catalytic converter from damage. Ford?s testing of this condition on the subject vehicles showed that a vehicle experiencing such a condition would continue to maintain its speed as well as accelerate, albeit at a lower rate than expected by the driver.Similar results were obtained in testing done by NHTSA?s Vehicle Research and Testing Center in East Liberty, Ohio (Figure 6).In an ongoing process to address the problem Ford issued a series of TSBs where a deflector shield was installed onto the CAC (Figures 3, 4 and 5).In January 2014 Ford indicated that its data shows that the TSBs have been effective in resolving the problem, that for the MY 2013 vehicles their remedy is 100% effective and the latest TSBs for MY 2011 ? 2012 are 95% effective.The 525 complaints to ODI and the total 4,120 unique VIN complaints listed in the Failure Report are incidents of alleged reduced power or driveability symptoms and not all are necessarily related to the condition created by water ingestion.Reduced power conditions can occur for a variety of reasons including faults with ignition coils, spark plugs, a catalytic converter, the throttle body, turbocharger, fuel pump/filter, powertrain control module (hardware or software) or transmission shifting problems.Ford also noted that in a large number of warranty claims on the subject vehicles, the CAC was replaced or a TSB procedure was performed when the symptoms exhibited were inconsistent with a CAC water ingestion related issue.Given these circumstances, further use of the agency resources in this matter does not appear to be warranted.Accordingly, this investigation is closed.The closing of
Engine
On May 22, 2013, the Office of Defects Investigation (ODI) opened PE13-018 to investigate 95 complaints alleging incidents of reduced engine power during hard accelerations in model year (MY) 2011 through 2013 Ford F-150 trucks.ODI was aware of three technical service bulletins (TSBs) issued by Ford for a condition that was related to moisture accumulation in the Charge Air Cooler (CAC) for the turbochargers.A Preliminary Evaluation was opened to gather information to assess whether the subject vehicles contain a safety related defect.The subject vehicles are powered by Ford?s 3.5L EcoBoost engine which uses twin turbochargers to obtain a balance of fuel economy and engine power based on the driver?s demand.When the driver requests more power from the engine, as in accelerating to pass, merge, ascend hills or haul a load the two turbochargers will spin up compressing the air which is then used to increase the power created by the combustion in the engine.The compressed air, which gains heat by the compression process, is passed through a Charge Air Cooler (CAC) which is designed to lower the temperature of the air in order to make the combustion process even more efficient (Figures 1 and 2).In response to ODI?s Information Request letter, Ford indicated that a misfire condition could occur after steady-speed operation under significantly humid and rainy conditions.Ford?s analysis found that under those conditions, condensation could form and accumulate on the inside of the CAC tubes which could then be ingested into the engine during particularly hard acceleration near wide-open throttle.An engine misfire of up to three cylinders could occur if the amount of condensed water released from the CAC exceeded the engine?s operating threshold for water ingestion.Ford noted that due to regulations set by the EPA, the powertrain software would disable up to two of the misfiring cylinders for no more than 30 seconds and until the driver tips out the throttle in order to protect the catalytic converter from damage. Ford?s testing of this condition on the subject vehicles showed that a vehicle experiencing such a condition would continue to maintain its speed as well as accelerate, albeit at a lower rate than expected by the driver.Similar results were obtained in testing done by NHTSA?s Vehicle Research and Testing Center in East Liberty, Ohio (Figure 6).In an ongoing process to address the problem Ford issued a series of TSBs where a deflector shield was installed onto the CAC (Figures 3, 4 and 5).In January 2014 Ford indicated that its data shows that the TSBs have been effective in resolving the problem, that for the MY 2013 vehicles their remedy is 100% effective and the latest TSBs for MY 2011 ? 2012 are 95% effective.The 525 complaints to ODI and the total 4,120 unique VIN complaints listed in the Failure Report are incidents of alleged reduced power or driveability symptoms and not all are necessarily related to the condition created by water ingestion.Reduced power conditions can occur for a variety of reasons including faults with ignition coils, spark plugs, a catalytic converter, the throttle body, turbocharger, fuel pump/filter, powertrain control module (hardware or software) or transmission shifting problems.Ford also noted that in a large number of warranty claims on the subject vehicles, the CAC was replaced or a TSB procedure was performed when the symptoms exhibited were inconsistent with a CAC water ingestion related issue.Given these circumstances, further use of the agency resources in this matter does not appear to be warranted.Accordingly, this investigation is closed.The closing of