IllustrationTHE POSITION 27 FUSE ON THE ENGINE COMPARTMENT FUSE BOX WAS BLACK, MELTED AND CRUMBLING. FROM RESEARCHING THIS, IT SEEMS TO BE A COMMON ISSUE. I FOUND THIS OUT IN MY DRIVEWAY WHILE IT WAS PARKED AND WOULD NOT START.
2012 Ford F-150
Owner reports · Recalls · Investigations
More warning signs than most F-150 years
Owner complaints for the 2012 Ford F-150 are substantially higher than the model-year median of 676.
About this comparison →How this year compares
Owner complaints by model year
Compare all F-150 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
3550–25K
24225–50K
26450–75K
21775–100K
259100–150K
133150K+
1,470 reports with mileage · 310 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 678 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 482 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Steering. Review the 204 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
40 crash reports14 fire reports23 injury reports
Fuel/propulsion System complaints
84 reportsTL* THE CONTACT OWNS A 2012 FORD F-150. THE CONTACT STATED THAT WHILE ATTEMPTING TO START THE VEHICLE, THE VEHICLE FAILED TO START. THE CONTACT BECAME AWARE THAT THE FUEL PUMP FUSE WAS MELTED WHILE INSPECTING THE FUSE PANEL. EPIC FORD LOCATED AT 5200 EVERGREEN WAY, EVERETT, WA 98203, (425) 353-7171, WAS CONTACTED BY PHONE AND WE…
Read full complaint
TL* THE CONTACT OWNS A 2012 FORD F-150. THE CONTACT STATED THAT WHILE ATTEMPTING TO START THE VEHICLE, THE VEHICLE FAILED TO START. THE CONTACT BECAME AWARE THAT THE FUEL PUMP FUSE WAS MELTED WHILE INSPECTING THE FUSE PANEL. EPIC FORD LOCATED AT 5200 EVERGREEN WAY, EVERETT, WA 98203, (425) 353-7171, WAS CONTACTED BY PHONE AND WERE MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT TAKEN TO BE DIAGNOSED. THE FUSE WAS REPLACED BY THE CONTACT. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 70,000.
TRUCK LOST POWER DUE TO A PROBLEM WITH THE FUEL PUMP FUSE LOCATION
WHILE ACCELERATING ONTO A HIGHWAY, THE VEHICLE COMPLETELY LOST POWER AND THE ENGINE STOPPED AND COULD NOT BE RESTARTED. HAD TO COAST TO A SAFE SPOT TO PULL OF THE ROAD. AFTER INVESTIGATING THE PROBLEM, I DISCOVERED THAT THE FUSE FOR THE FUEL PUMP HAD BLOWN AND MELTED THE FUSE BLOCK WHERE THE FUSE IS INSERTED. THIS IS A KNOWN PRO…
Read full complaint
WHILE ACCELERATING ONTO A HIGHWAY, THE VEHICLE COMPLETELY LOST POWER AND THE ENGINE STOPPED AND COULD NOT BE RESTARTED. HAD TO COAST TO A SAFE SPOT TO PULL OF THE ROAD. AFTER INVESTIGATING THE PROBLEM, I DISCOVERED THAT THE FUSE FOR THE FUEL PUMP HAD BLOWN AND MELTED THE FUSE BLOCK WHERE THE FUSE IS INSERTED. THIS IS A KNOWN PROBLEM AT FORD FOR THIS VEHICLE AND THEY HAVE ISSUED A TECHNICAL SERVICE BULLETIN FOR THEIR DEALERSHIPS TO MOVE THE FUEL PUMP FUSE TO A DIFFERENT BLOCK WITHIN THE FUSE PANEL AND INSTALL A FUSE BLOCK THAT WILL HANDLE THE REQUIRED AMPERAGE. THIS IS A PROBLEM THAT SHOULD DEFINITELY BE A RECALL BY FORD BECAUSE OF THE NATURE OF THE FAILURE. LOSING COMPLETE POWER, INCLUDING POWER STEERING AND BRAKING CAPABILITY IS A SAFETY ISSUE AND SHOULD BE URGENTLY ADDRESSED BY FORD. THE NHTSA SHOULD FORCE FORD TO RECALL THESE VEHICLES AND FIX THIS ISSUE BEFORE MORE PEOPLE GET KILLED.
I TOOK MY 2012 F-150 TO BYERS FORD IN DELAWARE,OH. THEY WERE TO PERFORM THE 19S07 RECALL. THEY SAID THEY DID IT. AFTER LEAVING THE DEALERSHIP I NOTICED IMMEDIATELY THAT THE TRUCK SHIFTS VERY QUICKLY INTO FIRST AND THE BRAKES FELT DIFFERENT. THEN SINCE I HAVE PUT 4 BOTTLES OF COOLANT IN IT IN LESS THAN 3 MONTHS. OVERHEATING FREQU…
Read full complaint
I TOOK MY 2012 F-150 TO BYERS FORD IN DELAWARE,OH. THEY WERE TO PERFORM THE 19S07 RECALL. THEY SAID THEY DID IT. AFTER LEAVING THE DEALERSHIP I NOTICED IMMEDIATELY THAT THE TRUCK SHIFTS VERY QUICKLY INTO FIRST AND THE BRAKES FELT DIFFERENT. THEN SINCE I HAVE PUT 4 BOTTLES OF COOLANT IN IT IN LESS THAN 3 MONTHS. OVERHEATING FREQUENTLY AFTER ONLY 15-20 MINUTES OF DRIVING. THEN THE BREAKS DON'T WORK HALF THE TIME AND THE LIGHT COMES ON SERVICE BRAKES, I HAVE THEM CHECKED BY FORD THEY SAY NOTHING WRONG WITH THEM. NOW THE TRUCK SHAKES, OVERHEATING FREQUENTLY, BRAKES WORK PART OF THE TIME, WHERE IS THE COOLANT GOING? NO LIQUIDS ON THE GROUND UNDER THE TRUCK BUT IT SMELLS BURNT AND WET IN THE TAILPIPE. NOW BYERS FORD IS SAYING THAT IT IS JUST DUE TO 2 MORE RECALLS, ONE BEING THE VACUUM PUMP AND THE OTHER IS THE TRANSMISSION MODULE, BUT THEY SAY IT SHOULD BE OKAY TO DRIVE, THEY CAN'T GET ME A RENTAL CAR AND THEY CAN'T GET ME IN UNTIL OCTOBER 9TH BUT THEY SAY TO JUST KEEP DRIVING IT WITH MY BREAKS BARELY WORKING HALF THE TIME BECAUSE OF THE VACUUM PUMP AND IT OVERHEATING ALMOST EVERY TIME I DRIVE IT, HAVING TO FILL IT UP WITH COOLANT, LOSS OF POWER, SLUGGISH, MANY RANDOM COMPUTER ISSUES IT SEEMS BUT THEY SAY TO DRIVE IT? MY ENGINE AND TRANSMISSION BOTH OVERHEAT AND MAJOR IS I HAVE NO BREAKS HALF THE TIME, IT SEEMS LIKE THIS SHOULD BE A SAFETY CONCERN BUT THEY DON'T SEEM TO CARE OR WANT TO MAKE IT RIGHT AND ADDRESS ALL THE ISSUES THAT THE FIRST RECALL CREATED. THE TRUCK HAD NO PROBLEMS BEFORE THE RECALL AND NOW A BIG MESS THAT IS ABOUT TO BLOW UP THAT NOW HAS 2 MORE ADDITIONAL RECALLS BECAUSE OF THE FIRST ONE.
TL* THE CONTACT OWNS A 2012 FORD F-150. THE CONTACT STATED THAT THE ENGINE STALLED WHILE DRIVING OVER 70 MPH. THE CONTACT HEARD A BEEP SOUND AND THE LOW OIL PRESSURE INDICATOR ILLUMINATED WHEN THE FAILURE OCCURRED. THE FAILURE WAS EXPERIENCED SEVERAL TIMES. THE CONTACT WAS ABLE TO MOVE THE VEHICLE ONTO THE ROAD SHOULDER, RESTART…
Read full complaint
TL* THE CONTACT OWNS A 2012 FORD F-150. THE CONTACT STATED THAT THE ENGINE STALLED WHILE DRIVING OVER 70 MPH. THE CONTACT HEARD A BEEP SOUND AND THE LOW OIL PRESSURE INDICATOR ILLUMINATED WHEN THE FAILURE OCCURRED. THE FAILURE WAS EXPERIENCED SEVERAL TIMES. THE CONTACT WAS ABLE TO MOVE THE VEHICLE ONTO THE ROAD SHOULDER, RESTART THE ENGINE, AND DRIVE TO DAVID WILSON'S VILLA FORD (2550 NORTH TUSTIN STREET, ORANGE, CA 92865, (714)-509-5615). THE DEALER PERFORMED A DIAGNOSTIC TEST THAT LOCATED FAILURE CODE: 27 (FUEL PUMP). THE DEALER STATED THAT THE FUEL PUMP FUSE WAS LOCATED IN AN AREA THAT CAUSED THE FUSE TO OVERHEAT. THE DEALER RELOCATED THE FUEL PUMP FUSE TO ANOTHER AREA THAT WOULD NOT CAUSE THE FUEL PUMP FUSE TO OVERHEAT. THE MANUFACTURER WAS NOT CONTACTED. THE VEHICLE WAS REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 94,000.
WHILE TRAVELING AT 70 MPH THE VEHICLE STALLED WITH THE ENGINE SHUTTING DOWN IN MAIN LANES OF AN INTERSTATE. THE STALLED ENGINE RESULTED IN THE LOSS OF ALL POWER ASSIST FEATURES INCLUDING POWER STEERING AND POWER BRAKES. WE WERE ABLE TO NAVIGATE ACROSS SEVERAL LANES BEFORE COMING TO A COMPLETE STOP IN A TRAFFIC LANE BUT NOT SAF…
Read full complaint
WHILE TRAVELING AT 70 MPH THE VEHICLE STALLED WITH THE ENGINE SHUTTING DOWN IN MAIN LANES OF AN INTERSTATE. THE STALLED ENGINE RESULTED IN THE LOSS OF ALL POWER ASSIST FEATURES INCLUDING POWER STEERING AND POWER BRAKES. WE WERE ABLE TO NAVIGATE ACROSS SEVERAL LANES BEFORE COMING TO A COMPLETE STOP IN A TRAFFIC LANE BUT NOT SAFELY OFF THE INTERSTATE. AFTER CALLING FOR A TOW AND REQUESTED SERVICE. IT WAS DETERMINED THAT A FUSE POWERING THE ELECTRIC FUEL PUMP HAD "BURNED" OUT AND HAD TO BE REPLACED. SHOULD HAVE BEEN A SIMPLE SOLUTION, UPON FURTHER INVESTIGATION IT WAS DETERMINED THE FUSE PANEL HAD BEEN DAMAGED AND WOULD NO LONGER ACCEPT A FUSE AND HAS TO BE MODIFIED WITH THE FUSE LOCATION MOVED TO A NEW LOCATION AND UPGRADED TO A MORE ROBUST FUSE AND FUSE PLACEMENT SLOT. FORD HAS BEEN AWARE OF THIS PROBLEM AND HAS ONLY ELECTED TO FIX THOSE VEHICLES THAT EXHIBIT FAILURE AND AT THE COST OF THE CONSUMER IF NOT WITHIN THE WARRANTY PERIOD. THIS VEHICLE HAS BEEN RETURNED TO FORD DEALERS MULTIPLE TIMES WITH NO MENTION OF THIS PROBLEM OR REPAIR. FORD HAS ISSUED A TECHNICAL SERVICE BULLETIN (TSB 15-0137) AND HAS CREATED A SPECIFIC REPLACEMENT KIT, WHICH INCLUDES INSTRUCTIONS AND ALL NECESSARY PARTS TO PERFORM THE RELOCATION (MOTORCRAFT # EL3Z-14293-A). THIS SHOULD BE A RECALL AS IT IMPACTS THE SAFETY OF FORD'S F150 OWNERS, THEIR PASSENGERS AND THOSE THAT SHARE THE ROAD WITH THEM. FAILURE OF ALL POWER ASSIST FUNCTIONS WHILE TRAVELING AT HIGHWAY SPEEDS IS SCARY AND CREATES A DANGEROUS SITUATION FOR THOSE IN THE VEHICLE AND THOSE AROUND IT. IT ALSO CREATES AN EVEN MORE DANGEROUS SITUATION IF THE VEHICLE WAS BEING USED TO CROSS A BUSY INTERSECTION, STALLED AND THEN STOPPED IN THE CENTER OF THE INTERSECTION. INCLUDED ARE PICTURES OF THE FUSE AND THE FUSE BLOCK DAMAGED DURING THE FAILURE AND HONESTLY, A FIRE COULD HAVE EASILY STARTED AS A RESULT OF THIS FAILURE.
TSB 15-0131 TIMING CHAIN STRETCHES AND MAKES A LOUD RATTLE UPON STARTING AND EVENTUALLY LEADS TO LOSS OF POWER AND ENGINE DAMAGE. THE KNOWN CAUSE OF THIS IS ALL THE PHASERS,THE INTAKE AND EXHAUST PHASERS. THIS IS MY MAIN CONCERN. EVERYONE I KNOW WHO OWNS THIS VEHICLE HAS THIS PROBLEM. THE OTHER COMPLAINT IS THAT I GET 14 MPG.
I BOUGHT IT WITH @ 10,000 MILES ON THE ODOMETER. I HAVE HAD NOTHING BUT [XXX] WITH IT FROM DAY ONE. FIRST OFF I PUT TWO NEW FRONT ROTORS AND BRAKE PADS ALL THE WAY AROUND AND BOTH IDLER PULLEYS WERE SQUEALING SO I REPLACED THEM . THEN AT @ 19,000 MILES I HAD TO REPLACE BOTH CVJ HALF SHAFTS . NOW AT 45,000 MILES THEY ARE BOTH SHO…
Read full complaint
I BOUGHT IT WITH @ 10,000 MILES ON THE ODOMETER. I HAVE HAD NOTHING BUT [XXX] WITH IT FROM DAY ONE. FIRST OFF I PUT TWO NEW FRONT ROTORS AND BRAKE PADS ALL THE WAY AROUND AND BOTH IDLER PULLEYS WERE SQUEALING SO I REPLACED THEM . THEN AT @ 19,000 MILES I HAD TO REPLACE BOTH CVJ HALF SHAFTS . NOW AT 45,000 MILES THEY ARE BOTH SHOT AGAIN THE CVJ HALF SHAFTS ARE . ON THE FIRST OF JANUARY THIS YEAR I WAS DRIVING DOWN THE ROAD AND THE VEHICLE WAS RUNNING GOOD SUDDENLY IT BEGAN TO CUT OUT AND THE POWER FELL OFF ON ITS FACE. I PURCHASED AN OBD11 CODE READER TO TRY AND DIAGNOSE THE PROBLEM. IT TELLS ME THAT RANDOM MISFIRE DETECTED AND THAT CYLINDERS 5 6 7 8 ARE MISFIRING . LET ME JUST SAY THAT 4 MONTHS LATER AFTER GOING THRU EVERYTHING FROM THE PLUGS WIRES INJECTORS AND REPLACING THE FUEL PUMP MODULE ASSEMBLY IT IS STILL NOT RUNNING AND I'M AT MY END OF TRYING TO GET THE PEICE OF $*** RUNNING. THERE IS NO WAY IN [XXX] AT 45,000 MILES ON THE VEHICLE THAT I SHOULD BE HAVING ALL THE [XXX] WITH THE VEHICLE. I LIVE IN NEW MEXICO AND WE DO HAVE A LEMON LAW HERE. I AM BEYOND THE SHADOW OF A DOUBT SURE THAT THIS TRUCK IS A [XXX] LEMON. PARTS OF THIS DOCUMENT HAVE BEEN REDACTED TO PROTECT PERSONALLY IDENTIFIABLE INFORMATION PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
DRIVING VEHICLE AT APPROX 65MPH, ENGINE LOST POWER, ENGINE WRENCH LIGHT, ILLUMINATED, OIL PRESSURE LIGHT ILLUMINATED, ENGINE SHIFTED TO 'LIMP MODE'. NO ACCELERATION. PULLED OVER TO THE SIDE OF THE HIGHWAY. WAITED 2 MINUTES AND RESTARTED THE ENGINE. WAS ABLE TO GET HOME. TOOK TO CERTIFIED FORD DEALERSHIP FOR REPAIR. ISSUE O…
Read full complaint
DRIVING VEHICLE AT APPROX 65MPH, ENGINE LOST POWER, ENGINE WRENCH LIGHT, ILLUMINATED, OIL PRESSURE LIGHT ILLUMINATED, ENGINE SHIFTED TO 'LIMP MODE'. NO ACCELERATION. PULLED OVER TO THE SIDE OF THE HIGHWAY. WAITED 2 MINUTES AND RESTARTED THE ENGINE. WAS ABLE TO GET HOME. TOOK TO CERTIFIED FORD DEALERSHIP FOR REPAIR. ISSUE OCCURRED TWICE MORE WHILE DRIVING TO THE DEALERSHIP FOR REPAIR. NEEDED TO REPLACE THE THROTTLE BODY.
Official recalls
419V075000 · Power Train:automatic Transmission; Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
Feb 11, 2019
Ford Motor Company (Ford) is recalling certain 2011-2013 F-150 vehicles equipped with a 6-speed automatic transmission. The transmission may unexpectedly downshift into first gear, regardless of vehicle speed.
Consequence & remedy
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began March 4, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S07.
Additional source detail variants (2)
Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
Ford Motor Company (Ford) is recalling certain 2011-2013 F-150 vehicles equipped with a 6-speed automatic transmission. The transmission may unexpectedly downshift into first gear, regardless of vehicle speed.
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began March 4, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S07.
Power Train:automatic Transmission
Ford Motor Company (Ford) is recalling certain 2011-2013 F-150 vehicles equipped with a 6-speed automatic transmission. The transmission may unexpectedly downshift into first gear, regardless of vehicle speed.
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began March 4, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S07.
16V248000 · Power Train:automatic Transmission
Apr 27, 2016
Ford Motor Company (Ford) is recalling certain model year 2011-2012 Ford F-150 trucks, 2012 Ford Expedition, Lincoln Navigator, and Ford Mustang vehicles. The affected vehicles are equipped with an automatic transmission that may unexpectedly downshift to first gear, regardless of vehicle speed.
Consequence & remedy
Consequence: An unexpected downshift into first gear can cause the vehicle to slow down suddenly without warning and the rear tires may slide or lock, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module with updated software, free of charge. The recall began on September 19, 2016. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S19.
12V190000 · Exterior Lighting:back Up Lights; Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
May 3, 2012
FORD IS RECALLING CERTAIN MODEL YEAR 2011-2012 FORD F-150, 2012 EXPEDITION AND LINCOLN NAVIGATOR, AND 2012-2013 MUSTANG VEHICLES, FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 102, "TRANSMISSION SHIFT LEVER SEQUENCE, STARTER INTERLOCK, AND TRANSMISSION BRAKING EFFECT" AND 108 LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT. THESE VEHICLES MAY HAVE A TRANSMISSION RANGE SENSOR (TRS) THAT WAS CALIBRATED OUT OF SPECIFICATION FOR REVERSE GEAR.
Consequence & remedy
Consequence: IF THIS CONDITION EXISTS, THE TRANSMISSION MAY NOT GO INTO REVERSE OR WHEN THE DRIVER PUSHES THE SHIFT LEVER IN THE REVERSE R POSITION AND THE VEHICLES TRANSMISSION DOES GO IN REVERSE, THE R MAY NOT ILLUMINATE ON THE DASHBOARD OF THE F-150, EXPEDITION, OR NAVIGATOR MODELS AND/OR THE BACKUP LAMP ON THE REAR OF THE F-150, EXPEDITION, NAVIGATOR, OR MUSTANG VEHICLES MAY NOT ILLUMINATE. THESE CONDITIONS INCREASE THE RISK OF A CRASH OR A PEDESTRIAN BEING STRUCK DUE TO THE VEHICLES NOT SIGNALING IT IS IN REVERSE.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT AND REPLACE THE TRS AS NECESSARY, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 11, 2012. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
Additional source detail variants (2)
Exterior Lighting:back Up Lights
FORD IS RECALLING CERTAIN MODEL YEAR 2011-2012 FORD F-150, 2012 EXPEDITION AND LINCOLN NAVIGATOR, AND 2012-2013 MUSTANG VEHICLES, FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 102, "TRANSMISSION SHIFT LEVER SEQUENCE, STARTER INTERLOCK, AND TRANSMISSION BRAKING EFFECT" AND 108 LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT. THESE VEHICLES MAY HAVE A TRANSMISSION RANGE SENSOR (TRS) THAT WAS CALIBRATED OUT OF SPECIFICATION FOR REVERSE GEAR.
Consequence: IF THIS CONDITION EXISTS, THE TRANSMISSION MAY NOT GO INTO REVERSE OR WHEN THE DRIVER PUSHES THE SHIFT LEVER IN THE REVERSE R POSITION AND THE VEHICLES TRANSMISSION DOES GO IN REVERSE, THE R MAY NOT ILLUMINATE ON THE DASHBOARD OF THE F-150, EXPEDITION, OR NAVIGATOR MODELS AND/OR THE BACKUP LAMP ON THE REAR OF THE F-150, EXPEDITION, NAVIGATOR, OR MUSTANG VEHICLES MAY NOT ILLUMINATE. THESE CONDITIONS INCREASE THE RISK OF A CRASH OR A PEDESTRIAN BEING STRUCK DUE TO THE VEHICLES NOT SIGNALING IT IS IN REVERSE.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT AND REPLACE THE TRS AS NECESSARY, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 11, 2012. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
FORD IS RECALLING CERTAIN MODEL YEAR 2011-2012 FORD F-150, 2012 EXPEDITION AND LINCOLN NAVIGATOR, AND 2012-2013 MUSTANG VEHICLES, FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 102, "TRANSMISSION SHIFT LEVER SEQUENCE, STARTER INTERLOCK, AND TRANSMISSION BRAKING EFFECT" AND 108 LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT. THESE VEHICLES MAY HAVE A TRANSMISSION RANGE SENSOR (TRS) THAT WAS CALIBRATED OUT OF SPECIFICATION FOR REVERSE GEAR.
Consequence: IF THIS CONDITION EXISTS, THE TRANSMISSION MAY NOT GO INTO REVERSE OR WHEN THE DRIVER PUSHES THE SHIFT LEVER IN THE REVERSE R POSITION AND THE VEHICLES TRANSMISSION DOES GO IN REVERSE, THE R MAY NOT ILLUMINATE ON THE DASHBOARD OF THE F-150, EXPEDITION, OR NAVIGATOR MODELS AND/OR THE BACKUP LAMP ON THE REAR OF THE F-150, EXPEDITION, NAVIGATOR, OR MUSTANG VEHICLES MAY NOT ILLUMINATE. THESE CONDITIONS INCREASE THE RISK OF A CRASH OR A PEDESTRIAN BEING STRUCK DUE TO THE VEHICLES NOT SIGNALING IT IS IN REVERSE.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT AND REPLACE THE TRS AS NECESSARY, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 11, 2012. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
12V198000 · Air Bags:frontal:sensor/control MODULE-INACTIVE
May 3, 2012
FORD IS RECALLING CERTAIN MODEL YEAR 2012 F-150 VEHICLES MANUFACTURED FROM NOVEMBER 6, 2011, THROUGH NOVEMBER 15, 2011. INCORRECT SOFTWARE FOR THE OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) WAS INSTALLED ON THE VEHICLES EITHER AT THE TIME OF MANUFACTURING OR DURING THE COURSE OF REPLACEMENT OF THE MODULE AS PART OF A SERVICE REPAIR. UNDER CERTAIN DRIVING CONDITIONS, THE OCSM MAY MISCLASSIFY THE PASSENGER SEATS OCCUPANT SUCH THAT THE PASSENGER SIDE AIRBAG DOES NOT DEPLOY WHEN IT SHOULD, DOES NOT DEPLOY AS INTENDED, OR DEPLOYS WHEN IT SHOULD NOT.
Consequence & remedy
Consequence: A FAILURE TO DEPLOY, FAILURE TO DEPLOY AS INTENDED, OR A DEPLOYMENT WHEN NOT INTENDED, INCREASES THE RISK OF INJURY TO THE PASSENGER SIDE SEAT OCCUPANT.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE OCSM FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 21, 2012. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4RQ17010 · Unexpected Transmission Downshift
Opened Dec 25, 2017 · Closed Oct 22, 2019
Status: closed (inferred from source dates) · Power Train:automatic Transmission; Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of transmissions unexpectedly downshifting to a lower gear without input from the driver on model year (MY) 2011-2013 Ford F-150, Expedition and Navigator vehicles. ODI has received 455 unique reports related to the alleged problem that were not covered under a previous recall for this issue (16V-248).Expedition and Navigator complaint rates are lower than F-150 complaints. Of those 455 reports, 34.7% claimed that the rear wheels locked up when the transmission downshifted. There were 4 accident claims with no injuries. There are many instances where drivers report leaving their lane or the road because of this issue.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 783 unique reports related to the alleged problem. There were 6 accident claims with 3 injuries. Ford also submitted 1206 warranty claims related to transmission downshifting failures. The failure can occur at any time, but typically at higher speed, and include symptoms such as sudden transmission downshifting, loss of speedometer, erratic shifting of transmission, and transmission stuck in one gear. The failures typically occur without warning and may result in the rear wheels momentarily locking up. The driver often had to fully stop the vehicle and restart it to get the vehicle to shift properly.On February 2nd, 2019 Ford notified ODI that it would conduct a safety recall (19V-075) to remedy transmission downshifting failures on all 2011-2013 F-150 vehicles. Ford will also offer extended warranties to 2011-2013 Expedition and Navigator vehicles with the same issue. Per Ford, some vehicles may experience an intermittent loss of Transmission Output Speed Sensor (OSS) signal to the Powertrain Control Module (PCM), potentially resulting in a temporary unintended downshift into first gear. Ford will reprogram the PCM with software that will prevent an unintended downshift into first gear and illuminate the Malfunction Indicator Light in the event of an intermittent OSS signal loss.The recall action initiated by the manufacturer appears to address the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the identification (ODI) numbers found in the attached list.
Additional source detail variants (2)
Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of transmissions unexpectedly downshifting to a lower gear without input from the driver on model year (MY) 2011-2013 Ford F-150, Expedition and Navigator vehicles. ODI has received 455 unique reports related to the alleged problem that were not covered under a previous recall for this issue (16V-248).Expedition and Navigator complaint rates are lower than F-150 complaints. Of those 455 reports, 34.7% claimed that the rear wheels locked up when the transmission downshifted. There were 4 accident claims with no injuries. There are many instances where drivers report leaving their lane or the road because of this issue.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 783 unique reports related to the alleged problem. There were 6 accident claims with 3 injuries. Ford also submitted 1206 warranty claims related to transmission downshifting failures. The failure can occur at any time, but typically at higher speed, and include symptoms such as sudden transmission downshifting, loss of speedometer, erratic shifting of transmission, and transmission stuck in one gear. The failures typically occur without warning and may result in the rear wheels momentarily locking up. The driver often had to fully stop the vehicle and restart it to get the vehicle to shift properly.On February 2nd, 2019 Ford notified ODI that it would conduct a safety recall (19V-075) to remedy transmission downshifting failures on all 2011-2013 F-150 vehicles. Ford will also offer extended warranties to 2011-2013 Expedition and Navigator vehicles with the same issue. Per Ford, some vehicles may experience an intermittent loss of Transmission Output Speed Sensor (OSS) signal to the Powertrain Control Module (PCM), potentially resulting in a temporary unintended downshift into first gear. Ford will reprogram the PCM with software that will prevent an unintended downshift into first gear and illuminate the Malfunction Indicator Light in the event of an intermittent OSS signal loss.The recall action initiated by the manufacturer appears to address the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the identification (ODI) numbers found in the attached list.
Power Train:automatic Transmission
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of transmissions unexpectedly downshifting to a lower gear without input from the driver on model year (MY) 2011-2013 Ford F-150, Expedition and Navigator vehicles. ODI has received 455 unique reports related to the alleged problem that were not covered under a previous recall for this issue (16V-248).Expedition and Navigator complaint rates are lower than F-150 complaints. Of those 455 reports, 34.7% claimed that the rear wheels locked up when the transmission downshifted. There were 4 accident claims with no injuries. There are many instances where drivers report leaving their lane or the road because of this issue.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 783 unique reports related to the alleged problem. There were 6 accident claims with 3 injuries. Ford also submitted 1206 warranty claims related to transmission downshifting failures. The failure can occur at any time, but typically at higher speed, and include symptoms such as sudden transmission downshifting, loss of speedometer, erratic shifting of transmission, and transmission stuck in one gear. The failures typically occur without warning and may result in the rear wheels momentarily locking up. The driver often had to fully stop the vehicle and restart it to get the vehicle to shift properly.On February 2nd, 2019 Ford notified ODI that it would conduct a safety recall (19V-075) to remedy transmission downshifting failures on all 2011-2013 F-150 vehicles. Ford will also offer extended warranties to 2011-2013 Expedition and Navigator vehicles with the same issue. Per Ford, some vehicles may experience an intermittent loss of Transmission Output Speed Sensor (OSS) signal to the Powertrain Control Module (PCM), potentially resulting in a temporary unintended downshift into first gear. Ford will reprogram the PCM with software that will prevent an unintended downshift into first gear and illuminate the Malfunction Indicator Light in the event of an intermittent OSS signal loss.The recall action initiated by the manufacturer appears to address the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the identification (ODI) numbers found in the attached list.
EA15006 · Brake Vacuum Pump Failure
Opened Oct 16, 2015 · Closed Apr 28, 2016
Status: closed (inferred from source dates) · Service Brakes, Electric; Service Brakes, Hydraulic:power Assist; Service Brakes, Hydraulic:power Assist:vacuum
On February 15, 2016, Ford Motor Company initiated Customer Satisfaction Program 15N05 to extend warranty coverage for the electric vacuum pump in certain model year (MY) 2011 through 2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines.The program extends coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through July 30, 2016 regardless of mileage.Ford's program covers all repairs related to electric vacuum pump (EVP) malfunctions including excessive noise, vibration, or change in brake pedal feel while applying the brakes at cold start. Ford states that the engine intake manifold is the primary source of vacuum for the brake booster and is fully compliant to motor vehicle safety standards without the supplemental vacuum supplied by the EVP.The company also contends that failure modes related to the EVP are progressive and provide warning to operators by way of noise and vibration before an operator to experience any temporary change in brake pedal feel.ODI's analysis of warranty data found that the majority of claims involved consumer concerns with EVP noise or vibration from the left front fender area when the vehicle is first started. Continued operation in this mode with pump motor noise will eventually result in the EVP seizing or becoming non-functional.Component failure analysis indicated that Ford and its supplier, Continental, identified a pump crank drive corrosion condition due to moisture entry through the vacuum intake.Corrosion damage to EVP internal components may eventually result in a blown fuse in the power distribution box and total loss of EVP function.Analysis of consumer complaints, field reports, and warranty data related to EVP failures found thatincidents predominantly occurred in driveways and parking lots in the periods immediately after cold engine starts.Many consumers operated their vehicle for some period of time with a blown EVP fuse without realizing that the pump had failed or that the vehicle had a brake system malfunction.Consumers who did experience braking performance issues reporteda temporary hard brake pedal condition at start-up followed by more consistent normal pedal feel after few seconds.On June 22, 2015, Ford developed a remedy procedure and issued TSB 15-0105 instructing dealers to replace the vacuum pump and install a new vacuum pump harness kit. In addition to reviewing test data submitted by Ford, ODI assessed safety risks associated with the alleged defect under various operating conditions, including: 1) baseline system performance with full engine and EVP vacuum available using exemplar parts, 2) disabled EVP and booster vacuum regulated to simulate worst case conditions for engine intake manifold vacuum supply to the brake booster (approximately 300 mbar); and 3) all source vacuum to the brake booster removed and Optimized Hydraulic Braking (OHB) mode active to represent complete loss of brake booster function (note: this condition is a more severe brake boost system failure mode than the alleged defect).ODI also analyzed all complaints and warranty claims to identify incidents alleging brake system performance concerns related to EVP failures.These analyses identified no brake performance issues or resulting changes in stopping distances either on highway or city traffic conditions.Two complaints alleging EVP malfunctions caused or contributed to rear-end collisions during attempted decelerations from road speeds are not believed to be related to the alleged defect.The EVP provides supplemental vacuum during initial start-up and idle
Additional source detail variants (3)
Service Brakes, Electric
On February 15, 2016, Ford Motor Company initiated Customer Satisfaction Program 15N05 to extend warranty coverage for the electric vacuum pump in certain model year (MY) 2011 through 2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines.The program extends coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through July 30, 2016 regardless of mileage.Ford's program covers all repairs related to electric vacuum pump (EVP) malfunctions including excessive noise, vibration, or change in brake pedal feel while applying the brakes at cold start. Ford states that the engine intake manifold is the primary source of vacuum for the brake booster and is fully compliant to motor vehicle safety standards without the supplemental vacuum supplied by the EVP.The company also contends that failure modes related to the EVP are progressive and provide warning to operators by way of noise and vibration before an operator to experience any temporary change in brake pedal feel.ODI's analysis of warranty data found that the majority of claims involved consumer concerns with EVP noise or vibration from the left front fender area when the vehicle is first started. Continued operation in this mode with pump motor noise will eventually result in the EVP seizing or becoming non-functional.Component failure analysis indicated that Ford and its supplier, Continental, identified a pump crank drive corrosion condition due to moisture entry through the vacuum intake.Corrosion damage to EVP internal components may eventually result in a blown fuse in the power distribution box and total loss of EVP function.Analysis of consumer complaints, field reports, and warranty data related to EVP failures found thatincidents predominantly occurred in driveways and parking lots in the periods immediately after cold engine starts.Many consumers operated their vehicle for some period of time with a blown EVP fuse without realizing that the pump had failed or that the vehicle had a brake system malfunction.Consumers who did experience braking performance issues reporteda temporary hard brake pedal condition at start-up followed by more consistent normal pedal feel after few seconds.On June 22, 2015, Ford developed a remedy procedure and issued TSB 15-0105 instructing dealers to replace the vacuum pump and install a new vacuum pump harness kit. In addition to reviewing test data submitted by Ford, ODI assessed safety risks associated with the alleged defect under various operating conditions, including: 1) baseline system performance with full engine and EVP vacuum available using exemplar parts, 2) disabled EVP and booster vacuum regulated to simulate worst case conditions for engine intake manifold vacuum supply to the brake booster (approximately 300 mbar); and 3) all source vacuum to the brake booster removed and Optimized Hydraulic Braking (OHB) mode active to represent complete loss of brake booster function (note: this condition is a more severe brake boost system failure mode than the alleged defect).ODI also analyzed all complaints and warranty claims to identify incidents alleging brake system performance concerns related to EVP failures.These analyses identified no brake performance issues or resulting changes in stopping distances either on highway or city traffic conditions.Two complaints alleging EVP malfunctions caused or contributed to rear-end collisions during attempted decelerations from road speeds are not believed to be related to the alleged defect.The EVP provides supplemental vacuum during initial start-up and idle
Service Brakes, Hydraulic:power Assist
On February 15, 2016, Ford Motor Company initiated Customer Satisfaction Program 15N05 to extend warranty coverage for the electric vacuum pump in certain model year (MY) 2011 through 2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines.The program extends coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through July 30, 2016 regardless of mileage.Ford's program covers all repairs related to electric vacuum pump (EVP) malfunctions including excessive noise, vibration, or change in brake pedal feel while applying the brakes at cold start. Ford states that the engine intake manifold is the primary source of vacuum for the brake booster and is fully compliant to motor vehicle safety standards without the supplemental vacuum supplied by the EVP.The company also contends that failure modes related to the EVP are progressive and provide warning to operators by way of noise and vibration before an operator to experience any temporary change in brake pedal feel.ODI's analysis of warranty data found that the majority of claims involved consumer concerns with EVP noise or vibration from the left front fender area when the vehicle is first started. Continued operation in this mode with pump motor noise will eventually result in the EVP seizing or becoming non-functional.Component failure analysis indicated that Ford and its supplier, Continental, identified a pump crank drive corrosion condition due to moisture entry through the vacuum intake.Corrosion damage to EVP internal components may eventually result in a blown fuse in the power distribution box and total loss of EVP function.Analysis of consumer complaints, field reports, and warranty data related to EVP failures found thatincidents predominantly occurred in driveways and parking lots in the periods immediately after cold engine starts.Many consumers operated their vehicle for some period of time with a blown EVP fuse without realizing that the pump had failed or that the vehicle had a brake system malfunction.Consumers who did experience braking performance issues reporteda temporary hard brake pedal condition at start-up followed by more consistent normal pedal feel after few seconds.On June 22, 2015, Ford developed a remedy procedure and issued TSB 15-0105 instructing dealers to replace the vacuum pump and install a new vacuum pump harness kit. In addition to reviewing test data submitted by Ford, ODI assessed safety risks associated with the alleged defect under various operating conditions, including: 1) baseline system performance with full engine and EVP vacuum available using exemplar parts, 2) disabled EVP and booster vacuum regulated to simulate worst case conditions for engine intake manifold vacuum supply to the brake booster (approximately 300 mbar); and 3) all source vacuum to the brake booster removed and Optimized Hydraulic Braking (OHB) mode active to represent complete loss of brake booster function (note: this condition is a more severe brake boost system failure mode than the alleged defect).ODI also analyzed all complaints and warranty claims to identify incidents alleging brake system performance concerns related to EVP failures.These analyses identified no brake performance issues or resulting changes in stopping distances either on highway or city traffic conditions.Two complaints alleging EVP malfunctions caused or contributed to rear-end collisions during attempted decelerations from road speeds are not believed to be related to the alleged defect.The EVP provides supplemental vacuum during initial start-up and idle
Service Brakes, Hydraulic:power Assist:vacuum
On February 15, 2016, Ford Motor Company initiated Customer Satisfaction Program 15N05 to extend warranty coverage for the electric vacuum pump in certain model year (MY) 2011 through 2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines.The program extends coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through July 30, 2016 regardless of mileage.Ford's program covers all repairs related to electric vacuum pump (EVP) malfunctions including excessive noise, vibration, or change in brake pedal feel while applying the brakes at cold start. Ford states that the engine intake manifold is the primary source of vacuum for the brake booster and is fully compliant to motor vehicle safety standards without the supplemental vacuum supplied by the EVP.The company also contends that failure modes related to the EVP are progressive and provide warning to operators by way of noise and vibration before an operator to experience any temporary change in brake pedal feel.ODI's analysis of warranty data found that the majority of claims involved consumer concerns with EVP noise or vibration from the left front fender area when the vehicle is first started. Continued operation in this mode with pump motor noise will eventually result in the EVP seizing or becoming non-functional.Component failure analysis indicated that Ford and its supplier, Continental, identified a pump crank drive corrosion condition due to moisture entry through the vacuum intake.Corrosion damage to EVP internal components may eventually result in a blown fuse in the power distribution box and total loss of EVP function.Analysis of consumer complaints, field reports, and warranty data related to EVP failures found thatincidents predominantly occurred in driveways and parking lots in the periods immediately after cold engine starts.Many consumers operated their vehicle for some period of time with a blown EVP fuse without realizing that the pump had failed or that the vehicle had a brake system malfunction.Consumers who did experience braking performance issues reporteda temporary hard brake pedal condition at start-up followed by more consistent normal pedal feel after few seconds.On June 22, 2015, Ford developed a remedy procedure and issued TSB 15-0105 instructing dealers to replace the vacuum pump and install a new vacuum pump harness kit. In addition to reviewing test data submitted by Ford, ODI assessed safety risks associated with the alleged defect under various operating conditions, including: 1) baseline system performance with full engine and EVP vacuum available using exemplar parts, 2) disabled EVP and booster vacuum regulated to simulate worst case conditions for engine intake manifold vacuum supply to the brake booster (approximately 300 mbar); and 3) all source vacuum to the brake booster removed and Optimized Hydraulic Braking (OHB) mode active to represent complete loss of brake booster function (note: this condition is a more severe brake boost system failure mode than the alleged defect).ODI also analyzed all complaints and warranty claims to identify incidents alleging brake system performance concerns related to EVP failures.These analyses identified no brake performance issues or resulting changes in stopping distances either on highway or city traffic conditions.Two complaints alleging EVP malfunctions caused or contributed to rear-end collisions during attempted decelerations from road speeds are not believed to be related to the alleged defect.The EVP provides supplemental vacuum during initial start-up and idle
PE15026 · Brake Vacuum Pump Failure
Opened Jun 22, 2015 · Closed Oct 19, 2015
Status: closed (inferred from source dates) · Service Brakes, Electric; Service Brakes, Hydraulic:power Assist; Service Brakes, Hydraulic:power Assist:vacuum
On June 22, 2015, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE15-026 to investigate incidents of increased brake pedal effort at cold start and extended stopping distance while driving in traffic, resulting from failures of the electric brake vacuum assist pump in model year (MY) 2011-2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines. In response to ODI's Information Request (IR) for PE15-026, Ford provided ODI with 396 complaints and field reports relating to incidents of increased brake pedal effort or malfunctions in the electric vacuum pump (EVP). ODI's analysis of the data provided by Ford identified 7 crashes and 1,851 warranty claims related to either a hard brake pedal condition or reduced brake effectiveness. Additionally, ODI identified one report in its database alleging an injury to an occupant of a vehicle struck in the rear by a subject F-150 vehicle with a failed EVP as documented in the police accident report referencing a dealer assessment of the pump.According to Ford, the subject vehicles utilize a traditional brake vacuum booster to provide power assist for braking and the EVP is intended to operate to maintain consistent brake pedal feel. The engine intake manifold is the primary source of vacuum for the booster and is fully compliant to motor vehicle safety standards without the EVP. Ford described the conditions related to a change in brake pedal feel as limited and temporary and provided component failure analysis showing evidence of water entry into the EVP which caused internal pump corrosion. Ford indicated that the EVP failure mode is progressive and provides warning to operators by way of noise and vibration before an operator is likely to experience any temporary change in brake pedal feel. Damage to the EVP motor bearing may eventually result in a blown EVP fuse and total loss of EVP function. Ford provided test data showing the brake pedal forces and pedal travel curves over time for 0.3g decelerations to a stop from 80kph (50mph) for: 1) normal system (full engine and EVP vacuum available); 2) Ford's approximation of worst case booster performance with EVP failure (EVP disabled and booster vacuum regulated to 300mbar to simulate cold start, all accessory loads on, and starting at 0 vacuum); and 3) with all source vacuum to the brake booster removed and Hydraulic Boost Compensation (HBC) active to represent complete loss of brake booster function. The Ford tests showed that the brake pedal forces required for achieving the 0.3g decelerations were relatively low for the normal condition, 35-40 N (8-9 lbf), increased by approximately 2-3 times normal when the EVP is disabled, 75-115 N (17-26 lbf), and increased by about 5-6 times normal for the complete brake booster failure condition, 205-215 N (46-48 lbf). This Preliminary Evaluation has been upgraded to Engineering Analysis (EA15-006) to test for EVP malfunctions under other vehicle operating conditions (e.g., low-speed driveway braking after cold-start with failed EVP), potential human factors contributions and to further assess the scope, frequency, and safety-related consequences of the alleged defect.The VOQs associated with the opening of this investigation are:10565994, 10575987, 10598351, 10604687, 10605701, 10607811, 10610491, 10615536, 10617828, 10619545, 10643075, 10650578, 10662151, 10664415, 10666988, 10668069, 10678844, 10695537, 10700874, 10706217, 10706271, 10712465, 10723033, 10723792, 10726960, 10730549, 10730721, 10730735, 10730837, 10730909, 10731008, 10731135, 10731157, 10731165, 10731395, 10731758, 10732609, 10732878, 10733375, 10733804, 10734558, 10734613, 10743859, 10744214, 10
Additional source detail variants (3)
Service Brakes, Electric
On June 22, 2015, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE15-026 to investigate incidents of increased brake pedal effort at cold start and extended stopping distance while driving in traffic, resulting from failures of the electric brake vacuum assist pump in model year (MY) 2011-2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines. In response to ODI's Information Request (IR) for PE15-026, Ford provided ODI with 396 complaints and field reports relating to incidents of increased brake pedal effort or malfunctions in the electric vacuum pump (EVP). ODI's analysis of the data provided by Ford identified 7 crashes and 1,851 warranty claims related to either a hard brake pedal condition or reduced brake effectiveness. Additionally, ODI identified one report in its database alleging an injury to an occupant of a vehicle struck in the rear by a subject F-150 vehicle with a failed EVP as documented in the police accident report referencing a dealer assessment of the pump.According to Ford, the subject vehicles utilize a traditional brake vacuum booster to provide power assist for braking and the EVP is intended to operate to maintain consistent brake pedal feel. The engine intake manifold is the primary source of vacuum for the booster and is fully compliant to motor vehicle safety standards without the EVP. Ford described the conditions related to a change in brake pedal feel as limited and temporary and provided component failure analysis showing evidence of water entry into the EVP which caused internal pump corrosion. Ford indicated that the EVP failure mode is progressive and provides warning to operators by way of noise and vibration before an operator is likely to experience any temporary change in brake pedal feel. Damage to the EVP motor bearing may eventually result in a blown EVP fuse and total loss of EVP function. Ford provided test data showing the brake pedal forces and pedal travel curves over time for 0.3g decelerations to a stop from 80kph (50mph) for: 1) normal system (full engine and EVP vacuum available); 2) Ford's approximation of worst case booster performance with EVP failure (EVP disabled and booster vacuum regulated to 300mbar to simulate cold start, all accessory loads on, and starting at 0 vacuum); and 3) with all source vacuum to the brake booster removed and Hydraulic Boost Compensation (HBC) active to represent complete loss of brake booster function. The Ford tests showed that the brake pedal forces required for achieving the 0.3g decelerations were relatively low for the normal condition, 35-40 N (8-9 lbf), increased by approximately 2-3 times normal when the EVP is disabled, 75-115 N (17-26 lbf), and increased by about 5-6 times normal for the complete brake booster failure condition, 205-215 N (46-48 lbf). This Preliminary Evaluation has been upgraded to Engineering Analysis (EA15-006) to test for EVP malfunctions under other vehicle operating conditions (e.g., low-speed driveway braking after cold-start with failed EVP), potential human factors contributions and to further assess the scope, frequency, and safety-related consequences of the alleged defect.The VOQs associated with the opening of this investigation are:10565994, 10575987, 10598351, 10604687, 10605701, 10607811, 10610491, 10615536, 10617828, 10619545, 10643075, 10650578, 10662151, 10664415, 10666988, 10668069, 10678844, 10695537, 10700874, 10706217, 10706271, 10712465, 10723033, 10723792, 10726960, 10730549, 10730721, 10730735, 10730837, 10730909, 10731008, 10731135, 10731157, 10731165, 10731395, 10731758, 10732609, 10732878, 10733375, 10733804, 10734558, 10734613, 10743859, 10744214, 10
Service Brakes, Hydraulic:power Assist
On June 22, 2015, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE15-026 to investigate incidents of increased brake pedal effort at cold start and extended stopping distance while driving in traffic, resulting from failures of the electric brake vacuum assist pump in model year (MY) 2011-2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines. In response to ODI's Information Request (IR) for PE15-026, Ford provided ODI with 396 complaints and field reports relating to incidents of increased brake pedal effort or malfunctions in the electric vacuum pump (EVP). ODI's analysis of the data provided by Ford identified 7 crashes and 1,851 warranty claims related to either a hard brake pedal condition or reduced brake effectiveness. Additionally, ODI identified one report in its database alleging an injury to an occupant of a vehicle struck in the rear by a subject F-150 vehicle with a failed EVP as documented in the police accident report referencing a dealer assessment of the pump.According to Ford, the subject vehicles utilize a traditional brake vacuum booster to provide power assist for braking and the EVP is intended to operate to maintain consistent brake pedal feel. The engine intake manifold is the primary source of vacuum for the booster and is fully compliant to motor vehicle safety standards without the EVP. Ford described the conditions related to a change in brake pedal feel as limited and temporary and provided component failure analysis showing evidence of water entry into the EVP which caused internal pump corrosion. Ford indicated that the EVP failure mode is progressive and provides warning to operators by way of noise and vibration before an operator is likely to experience any temporary change in brake pedal feel. Damage to the EVP motor bearing may eventually result in a blown EVP fuse and total loss of EVP function. Ford provided test data showing the brake pedal forces and pedal travel curves over time for 0.3g decelerations to a stop from 80kph (50mph) for: 1) normal system (full engine and EVP vacuum available); 2) Ford's approximation of worst case booster performance with EVP failure (EVP disabled and booster vacuum regulated to 300mbar to simulate cold start, all accessory loads on, and starting at 0 vacuum); and 3) with all source vacuum to the brake booster removed and Hydraulic Boost Compensation (HBC) active to represent complete loss of brake booster function. The Ford tests showed that the brake pedal forces required for achieving the 0.3g decelerations were relatively low for the normal condition, 35-40 N (8-9 lbf), increased by approximately 2-3 times normal when the EVP is disabled, 75-115 N (17-26 lbf), and increased by about 5-6 times normal for the complete brake booster failure condition, 205-215 N (46-48 lbf). This Preliminary Evaluation has been upgraded to Engineering Analysis (EA15-006) to test for EVP malfunctions under other vehicle operating conditions (e.g., low-speed driveway braking after cold-start with failed EVP), potential human factors contributions and to further assess the scope, frequency, and safety-related consequences of the alleged defect.The VOQs associated with the opening of this investigation are:10565994, 10575987, 10598351, 10604687, 10605701, 10607811, 10610491, 10615536, 10617828, 10619545, 10643075, 10650578, 10662151, 10664415, 10666988, 10668069, 10678844, 10695537, 10700874, 10706217, 10706271, 10712465, 10723033, 10723792, 10726960, 10730549, 10730721, 10730735, 10730837, 10730909, 10731008, 10731135, 10731157, 10731165, 10731395, 10731758, 10732609, 10732878, 10733375, 10733804, 10734558, 10734613, 10743859, 10744214, 10
Service Brakes, Hydraulic:power Assist:vacuum
On June 22, 2015, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE15-026 to investigate incidents of increased brake pedal effort at cold start and extended stopping distance while driving in traffic, resulting from failures of the electric brake vacuum assist pump in model year (MY) 2011-2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines. In response to ODI's Information Request (IR) for PE15-026, Ford provided ODI with 396 complaints and field reports relating to incidents of increased brake pedal effort or malfunctions in the electric vacuum pump (EVP). ODI's analysis of the data provided by Ford identified 7 crashes and 1,851 warranty claims related to either a hard brake pedal condition or reduced brake effectiveness. Additionally, ODI identified one report in its database alleging an injury to an occupant of a vehicle struck in the rear by a subject F-150 vehicle with a failed EVP as documented in the police accident report referencing a dealer assessment of the pump.According to Ford, the subject vehicles utilize a traditional brake vacuum booster to provide power assist for braking and the EVP is intended to operate to maintain consistent brake pedal feel. The engine intake manifold is the primary source of vacuum for the booster and is fully compliant to motor vehicle safety standards without the EVP. Ford described the conditions related to a change in brake pedal feel as limited and temporary and provided component failure analysis showing evidence of water entry into the EVP which caused internal pump corrosion. Ford indicated that the EVP failure mode is progressive and provides warning to operators by way of noise and vibration before an operator is likely to experience any temporary change in brake pedal feel. Damage to the EVP motor bearing may eventually result in a blown EVP fuse and total loss of EVP function. Ford provided test data showing the brake pedal forces and pedal travel curves over time for 0.3g decelerations to a stop from 80kph (50mph) for: 1) normal system (full engine and EVP vacuum available); 2) Ford's approximation of worst case booster performance with EVP failure (EVP disabled and booster vacuum regulated to 300mbar to simulate cold start, all accessory loads on, and starting at 0 vacuum); and 3) with all source vacuum to the brake booster removed and Hydraulic Boost Compensation (HBC) active to represent complete loss of brake booster function. The Ford tests showed that the brake pedal forces required for achieving the 0.3g decelerations were relatively low for the normal condition, 35-40 N (8-9 lbf), increased by approximately 2-3 times normal when the EVP is disabled, 75-115 N (17-26 lbf), and increased by about 5-6 times normal for the complete brake booster failure condition, 205-215 N (46-48 lbf). This Preliminary Evaluation has been upgraded to Engineering Analysis (EA15-006) to test for EVP malfunctions under other vehicle operating conditions (e.g., low-speed driveway braking after cold-start with failed EVP), potential human factors contributions and to further assess the scope, frequency, and safety-related consequences of the alleged defect.The VOQs associated with the opening of this investigation are:10565994, 10575987, 10598351, 10604687, 10605701, 10607811, 10610491, 10615536, 10617828, 10619545, 10643075, 10650578, 10662151, 10664415, 10666988, 10668069, 10678844, 10695537, 10700874, 10706217, 10706271, 10712465, 10723033, 10723792, 10726960, 10730549, 10730721, 10730735, 10730837, 10730909, 10731008, 10731135, 10731157, 10731165, 10731395, 10731758, 10732609, 10732878, 10733375, 10733804, 10734558, 10734613, 10743859, 10744214, 10
PE13018 · Reduced Power During Hard Acceleration
Opened May 22, 2013 · Closed Apr 7, 2014
Status: closed (inferred from source dates) · Engine; Engine And Engine Cooling
On May 22, 2013, the Office of Defects Investigation (ODI) opened PE13-018 to investigate 95 complaints alleging incidents of reduced engine power during hard accelerations in model year (MY) 2011 through 2013 Ford F-150 trucks.ODI was aware of three technical service bulletins (TSBs) issued by Ford for a condition that was related to moisture accumulation in the Charge Air Cooler (CAC) for the turbochargers.A Preliminary Evaluation was opened to gather information to assess whether the subject vehicles contain a safety related defect.The subject vehicles are powered by Ford?s 3.5L EcoBoost engine which uses twin turbochargers to obtain a balance of fuel economy and engine power based on the driver?s demand.When the driver requests more power from the engine, as in accelerating to pass, merge, ascend hills or haul a load the two turbochargers will spin up compressing the air which is then used to increase the power created by the combustion in the engine.The compressed air, which gains heat by the compression process, is passed through a Charge Air Cooler (CAC) which is designed to lower the temperature of the air in order to make the combustion process even more efficient (Figures 1 and 2).In response to ODI?s Information Request letter, Ford indicated that a misfire condition could occur after steady-speed operation under significantly humid and rainy conditions.Ford?s analysis found that under those conditions, condensation could form and accumulate on the inside of the CAC tubes which could then be ingested into the engine during particularly hard acceleration near wide-open throttle.An engine misfire of up to three cylinders could occur if the amount of condensed water released from the CAC exceeded the engine?s operating threshold for water ingestion.Ford noted that due to regulations set by the EPA, the powertrain software would disable up to two of the misfiring cylinders for no more than 30 seconds and until the driver tips out the throttle in order to protect the catalytic converter from damage. Ford?s testing of this condition on the subject vehicles showed that a vehicle experiencing such a condition would continue to maintain its speed as well as accelerate, albeit at a lower rate than expected by the driver.Similar results were obtained in testing done by NHTSA?s Vehicle Research and Testing Center in East Liberty, Ohio (Figure 6).In an ongoing process to address the problem Ford issued a series of TSBs where a deflector shield was installed onto the CAC (Figures 3, 4 and 5).In January 2014 Ford indicated that its data shows that the TSBs have been effective in resolving the problem, that for the MY 2013 vehicles their remedy is 100% effective and the latest TSBs for MY 2011 ? 2012 are 95% effective.The 525 complaints to ODI and the total 4,120 unique VIN complaints listed in the Failure Report are incidents of alleged reduced power or driveability symptoms and not all are necessarily related to the condition created by water ingestion.Reduced power conditions can occur for a variety of reasons including faults with ignition coils, spark plugs, a catalytic converter, the throttle body, turbocharger, fuel pump/filter, powertrain control module (hardware or software) or transmission shifting problems.Ford also noted that in a large number of warranty claims on the subject vehicles, the CAC was replaced or a TSB procedure was performed when the symptoms exhibited were inconsistent with a CAC water ingestion related issue.Given these circumstances, further use of the agency resources in this matter does not appear to be warranted.Accordingly, this investigation is closed.The closing of
Additional source detail variants (2)
Engine And Engine Cooling
On May 22, 2013, the Office of Defects Investigation (ODI) opened PE13-018 to investigate 95 complaints alleging incidents of reduced engine power during hard accelerations in model year (MY) 2011 through 2013 Ford F-150 trucks.ODI was aware of three technical service bulletins (TSBs) issued by Ford for a condition that was related to moisture accumulation in the Charge Air Cooler (CAC) for the turbochargers.A Preliminary Evaluation was opened to gather information to assess whether the subject vehicles contain a safety related defect.The subject vehicles are powered by Ford?s 3.5L EcoBoost engine which uses twin turbochargers to obtain a balance of fuel economy and engine power based on the driver?s demand.When the driver requests more power from the engine, as in accelerating to pass, merge, ascend hills or haul a load the two turbochargers will spin up compressing the air which is then used to increase the power created by the combustion in the engine.The compressed air, which gains heat by the compression process, is passed through a Charge Air Cooler (CAC) which is designed to lower the temperature of the air in order to make the combustion process even more efficient (Figures 1 and 2).In response to ODI?s Information Request letter, Ford indicated that a misfire condition could occur after steady-speed operation under significantly humid and rainy conditions.Ford?s analysis found that under those conditions, condensation could form and accumulate on the inside of the CAC tubes which could then be ingested into the engine during particularly hard acceleration near wide-open throttle.An engine misfire of up to three cylinders could occur if the amount of condensed water released from the CAC exceeded the engine?s operating threshold for water ingestion.Ford noted that due to regulations set by the EPA, the powertrain software would disable up to two of the misfiring cylinders for no more than 30 seconds and until the driver tips out the throttle in order to protect the catalytic converter from damage. Ford?s testing of this condition on the subject vehicles showed that a vehicle experiencing such a condition would continue to maintain its speed as well as accelerate, albeit at a lower rate than expected by the driver.Similar results were obtained in testing done by NHTSA?s Vehicle Research and Testing Center in East Liberty, Ohio (Figure 6).In an ongoing process to address the problem Ford issued a series of TSBs where a deflector shield was installed onto the CAC (Figures 3, 4 and 5).In January 2014 Ford indicated that its data shows that the TSBs have been effective in resolving the problem, that for the MY 2013 vehicles their remedy is 100% effective and the latest TSBs for MY 2011 ? 2012 are 95% effective.The 525 complaints to ODI and the total 4,120 unique VIN complaints listed in the Failure Report are incidents of alleged reduced power or driveability symptoms and not all are necessarily related to the condition created by water ingestion.Reduced power conditions can occur for a variety of reasons including faults with ignition coils, spark plugs, a catalytic converter, the throttle body, turbocharger, fuel pump/filter, powertrain control module (hardware or software) or transmission shifting problems.Ford also noted that in a large number of warranty claims on the subject vehicles, the CAC was replaced or a TSB procedure was performed when the symptoms exhibited were inconsistent with a CAC water ingestion related issue.Given these circumstances, further use of the agency resources in this matter does not appear to be warranted.Accordingly, this investigation is closed.The closing of
Engine
On May 22, 2013, the Office of Defects Investigation (ODI) opened PE13-018 to investigate 95 complaints alleging incidents of reduced engine power during hard accelerations in model year (MY) 2011 through 2013 Ford F-150 trucks.ODI was aware of three technical service bulletins (TSBs) issued by Ford for a condition that was related to moisture accumulation in the Charge Air Cooler (CAC) for the turbochargers.A Preliminary Evaluation was opened to gather information to assess whether the subject vehicles contain a safety related defect.The subject vehicles are powered by Ford?s 3.5L EcoBoost engine which uses twin turbochargers to obtain a balance of fuel economy and engine power based on the driver?s demand.When the driver requests more power from the engine, as in accelerating to pass, merge, ascend hills or haul a load the two turbochargers will spin up compressing the air which is then used to increase the power created by the combustion in the engine.The compressed air, which gains heat by the compression process, is passed through a Charge Air Cooler (CAC) which is designed to lower the temperature of the air in order to make the combustion process even more efficient (Figures 1 and 2).In response to ODI?s Information Request letter, Ford indicated that a misfire condition could occur after steady-speed operation under significantly humid and rainy conditions.Ford?s analysis found that under those conditions, condensation could form and accumulate on the inside of the CAC tubes which could then be ingested into the engine during particularly hard acceleration near wide-open throttle.An engine misfire of up to three cylinders could occur if the amount of condensed water released from the CAC exceeded the engine?s operating threshold for water ingestion.Ford noted that due to regulations set by the EPA, the powertrain software would disable up to two of the misfiring cylinders for no more than 30 seconds and until the driver tips out the throttle in order to protect the catalytic converter from damage. Ford?s testing of this condition on the subject vehicles showed that a vehicle experiencing such a condition would continue to maintain its speed as well as accelerate, albeit at a lower rate than expected by the driver.Similar results were obtained in testing done by NHTSA?s Vehicle Research and Testing Center in East Liberty, Ohio (Figure 6).In an ongoing process to address the problem Ford issued a series of TSBs where a deflector shield was installed onto the CAC (Figures 3, 4 and 5).In January 2014 Ford indicated that its data shows that the TSBs have been effective in resolving the problem, that for the MY 2013 vehicles their remedy is 100% effective and the latest TSBs for MY 2011 ? 2012 are 95% effective.The 525 complaints to ODI and the total 4,120 unique VIN complaints listed in the Failure Report are incidents of alleged reduced power or driveability symptoms and not all are necessarily related to the condition created by water ingestion.Reduced power conditions can occur for a variety of reasons including faults with ignition coils, spark plugs, a catalytic converter, the throttle body, turbocharger, fuel pump/filter, powertrain control module (hardware or software) or transmission shifting problems.Ford also noted that in a large number of warranty claims on the subject vehicles, the CAC was replaced or a TSB procedure was performed when the symptoms exhibited were inconsistent with a CAC water ingestion related issue.Given these circumstances, further use of the agency resources in this matter does not appear to be warranted.Accordingly, this investigation is closed.The closing of