IllustrationCODE P0016 TIMING CHAIN FAILURE. CAUSING CAR TO LOSE POWER WHEN ACCELERATING. THIS HAPPENED ON EXPRESSWAY WHEN I WAS TURNING INTO A LANE TO PASS A SEMI IN MY LANE. I HAD NO POWER TO GET GOING IN THE PASSING LANE AND ALMOST GOT REAR ENDED.ALSO CAUSES TRUCK TO JUMP WHEN FULLY STOPPED AND FOOT ON BREAK. THIS IS A ON GOING PROBLEM.
2012 Ford F-150
Owner reports · Recalls · Investigations
More warning signs than most F-150 years
Owner complaints for the 2012 Ford F-150 are substantially higher than the model-year median of 676.
About this comparison →How this year compares
Owner complaints by model year
Compare all F-150 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
3550–25K
24225–50K
26450–75K
21775–100K
259100–150K
133150K+
1,470 reports with mileage · 310 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 678 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 482 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Steering. Review the 204 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
40 crash reports14 fire reports23 injury reports
Engine complaints
482 reportsVEHICLE BACKFIRED AND STARTED SHUTTERING UPON ACCELERATION...CHECK ENGINE LIGHT CAME ON REPLACED IGNITION COIL 6. 1000 MILES LATER, SAME SITUATION CYLINDER 1&2...REPLACED THOSE COILS AND REPLACED SPARK PLUGS. SHUTTERING LESSONED, STILL BACKFIRED ON UPON STRONG ACCELERATION. DEFINITELY A SAFETY CONCERN. THE BACKFIRE DOES NOT T…
Read full complaint
VEHICLE BACKFIRED AND STARTED SHUTTERING UPON ACCELERATION...CHECK ENGINE LIGHT CAME ON REPLACED IGNITION COIL 6. 1000 MILES LATER, SAME SITUATION CYLINDER 1&2...REPLACED THOSE COILS AND REPLACED SPARK PLUGS. SHUTTERING LESSONED, STILL BACKFIRED ON UPON STRONG ACCELERATION. DEFINITELY A SAFETY CONCERN. THE BACKFIRE DOES NOT TRIGGER THE ENGINE LIGHT TO COME ON...FROM THE RESEARCH I'VE DONE, THIS SEAMS TO BE A COMMON PROBLEM WITH THE ECO BOOST
2012 F-150 HAS AN ECO BOOST 3.5 L MOTOR THAT MISFIRES IN DAMP/WET/RAINY/COOL WEATHER. MOTOR GOES INTO A MISFIRE MODE WITH NO POWER TO DRIVE OR ACCELERATE TRUCK. BEFORE THE MILEAGE WARRANTY WAS UP, TRUCK WAS TAKEN TO FORD FOR THEIR "FIX". HOWEVER, THE ISSUE HAS REMAINED FROM 2012 TO CURRENT YEAR, 2018, AND WITHOUT FORD FIXING …
Read full complaint
2012 F-150 HAS AN ECO BOOST 3.5 L MOTOR THAT MISFIRES IN DAMP/WET/RAINY/COOL WEATHER. MOTOR GOES INTO A MISFIRE MODE WITH NO POWER TO DRIVE OR ACCELERATE TRUCK. BEFORE THE MILEAGE WARRANTY WAS UP, TRUCK WAS TAKEN TO FORD FOR THEIR "FIX". HOWEVER, THE ISSUE HAS REMAINED FROM 2012 TO CURRENT YEAR, 2018, AND WITHOUT FORD FIXING THIS PROBLEM WILL CONTINUE FOR THE INDEFINITE FUTURE OF THESE MOTORS FROM FORD. CANNOT TRUST TRUCK TO PERFORM WHEN NEEDED AND A SAFETY HAZARD WHEN DRIVING, TOWING OR ACCELERATING WHEN THIS OCCURRS.
TL* THE CONTACT OWNS A 2012 FORD F-150. THE CONTACT STATED THAT THE VEHICLE LACKED ENGINE POWER WHEN THE VEHICLE WAS STATIONARY. AN INDEPENDENT MECHANIC INSPECTED THE VEHICLE AND FOUND A P0016 ERROR CODE, WHICH INDICATED THAT THE TIMING BELT WAS LOOSE AND NEEDED TO BE REPLACED. THE CONTACT VISITED THE DEALER (MEDFORD MOTORS, INC…
Read full complaint
TL* THE CONTACT OWNS A 2012 FORD F-150. THE CONTACT STATED THAT THE VEHICLE LACKED ENGINE POWER WHEN THE VEHICLE WAS STATIONARY. AN INDEPENDENT MECHANIC INSPECTED THE VEHICLE AND FOUND A P0016 ERROR CODE, WHICH INDICATED THAT THE TIMING BELT WAS LOOSE AND NEEDED TO BE REPLACED. THE CONTACT VISITED THE DEALER (MEDFORD MOTORS, INC, 105 WISCONSIN AVE, MEDFORD, WI 54451, (715) 748-3700) AND THE FAILURE WAS CONFIRMED. THE DEALER STATED THAT THE REPAIR WOULD COST OVER $3,000 WITHOUT A RECALL AVAILABLE. THE MANUFACTURER WAS NOTIFIED AND CONFIRMED WHAT THE DEALER STATED. THE FAILURE MILEAGE WAS 77,000. *TT CONSUMER STATED LOSS OF POWER.*JB
ENGINE FAILURE WHILE DRIVING ON CITY STREET. 85,XXX MILES ON VEHICLE. I PURCHASED VEHICLE NEW. ENGINE THREW A ROD. OIL SPILLED ALL OVER ROADWAY. RESEARCH CONDUCTED SHOWS THIS IS A COMMON PROBLEM WITH THE ECOBOOST ENGINE DUE TO INTERCOOLERS OR TIMING CHAIN ISSUES. HAD THERE BEEN ANOTHER VEHICLE BEHIND ME, THIS COULD HAVE RESULT…
Read full complaint
ENGINE FAILURE WHILE DRIVING ON CITY STREET. 85,XXX MILES ON VEHICLE. I PURCHASED VEHICLE NEW. ENGINE THREW A ROD. OIL SPILLED ALL OVER ROADWAY. RESEARCH CONDUCTED SHOWS THIS IS A COMMON PROBLEM WITH THE ECOBOOST ENGINE DUE TO INTERCOOLERS OR TIMING CHAIN ISSUES. HAD THERE BEEN ANOTHER VEHICLE BEHIND ME, THIS COULD HAVE RESULTED IN A CRASH DUE TO VEHICLE LOSING POWER WITH NO WARNING.
I HAVE A 2012 F150 IT KEEP LOCKING UP ON THE ROAD. FORD SAY MOISTURE IS GETTING IN THE ENGINE. THE TRUCK SUDDENLY STOP ON THE ROAD I HAVE ALMOST BEEN HIT ATLEAST 10 TIMES. SUBURBAN FORD DEALERSHIP IS BLAMING ME. I HAVE FOUND 330 PAGES OF COMPLAINT ABOUT THIS ISSUE. BUT YET KNOWBODY IS DOING NOTHING ABOUT IT. I AM REQUESTING THE…
Read full complaint
I HAVE A 2012 F150 IT KEEP LOCKING UP ON THE ROAD. FORD SAY MOISTURE IS GETTING IN THE ENGINE. THE TRUCK SUDDENLY STOP ON THE ROAD I HAVE ALMOST BEEN HIT ATLEAST 10 TIMES. SUBURBAN FORD DEALERSHIP IS BLAMING ME. I HAVE FOUND 330 PAGES OF COMPLAINT ABOUT THIS ISSUE. BUT YET KNOWBODY IS DOING NOTHING ABOUT IT. I AM REQUESTING THE GOVERNMENT TO INVESTIGATE THIS ISSUE. THIS IS A SAFETY ISSUE I HAVE BEEN NARROWLY MISS BY A SEMI TRUCK MY FAMILY COULD HAVE BEEN KILLED. IF THE GOVERNMENT DOES NOT THINK THIS VEHICLES LOCKING UP ON THE ROAD IS OF CONCERN I DONT KNOW WHAT IS. THE TRUCK SENDS CODES FOR #1 #3 #5 CYLINDERS HAVE SHUT DOWN WHILE DRIVING. THEN I HAVE HAD THE ENGINE VAPOR LOCK UP, BECAUSE THE INDUCTION IS NOT ALLOWING WATER IN THE MOTOR. HOW MANY PEOPLE THAT HAVE SPENT THEIR HARD EARNED MONEY ON THIS TRUCK AND HAVE HAD MAJOR ISSUES. WHO IS PROTECTING THE PUBLIC WE LOOK TO GOVERNMENT TO HELP. THIS VEHICLE HAS BIG ISSUES PLEASE HELP. ONE OF YOUR QUESTIONS ARE WHEN DID THIS HAPPEN, SINCE I BOUGHT THE TRUCK. FORD TOLD ME NOT TO DRIVE IT WHEN IT RAINS OR WHEN THE HUMIDITY IS HIGH. $65000.00 FOR A TRUCK AND I CAN'T DRIVE IT WHEN IT RAINS.
MY 2012 FORD F-150 IS HAVING SERIOUS SAFETY ISSUES THAT ARE ADDRESSED IN FOR TSB'S AND SAFETY RECALLS. UPON CONTACTING FORD MOTOR COMPANY, I WAS INFORMED THAT MY VEHICLE DID NOT HAVE THE SPECIFIC VIN NUMBER THAT MATCHED WITH THEIR CASES. MY VEHICLE FITS THE RECALL DESCRIPTIONS WITH MAKE, MODEL, YEAR, AND EVEN MANUFACTURING LOCAT…
Read full complaint
MY 2012 FORD F-150 IS HAVING SERIOUS SAFETY ISSUES THAT ARE ADDRESSED IN FOR TSB'S AND SAFETY RECALLS. UPON CONTACTING FORD MOTOR COMPANY, I WAS INFORMED THAT MY VEHICLE DID NOT HAVE THE SPECIFIC VIN NUMBER THAT MATCHED WITH THEIR CASES. MY VEHICLE FITS THE RECALL DESCRIPTIONS WITH MAKE, MODEL, YEAR, AND EVEN MANUFACTURING LOCATION AND HAS THE EXACT ISSUES THAT THESE RECALLS ARE ABOUT. THE FIRST RECALL IS FORD RECALL 16S19 : UNEXPECTED TRANSMISSION DOWNSHIFT THIS WILL CAUSE MY VEHICLE TO RANDOMLY DOWNSHIFT MULTIPLE GEARS. WHEN IT SHIFTS DOWN IT ALSO CAUSES THE REAR TIRES ARE LOCK UP AND I HAVE LOST CONTROL MOMENTARILY TRYING TO DRIVE AT HIGHWAY SPEEDS. THIS ALSO CAUSES WEAR AND TEAR ON THE DRIVETRAIN. SHIFTING THE MOTOR FROM 5TH GEAR TO 1ST IMMEDIATELY SENDS THE MOTOR INTO A DANGEROUS RPM RANGE CAUSING DAMAGE. THE SECOND RECALL IS FORD TSB 13-6-8: THIS CAUSES ME TO LOSE ALL INDICATION ON MY GAUGES EXCEPT FOR RPM' S. I LOSE INDICATION ON MY CURRENT SPEED RANDOMLY AND ALSO ON ALL OF MY CRITICAL ENGINE TEMPERATURES AND PRESSURES. THIS ALSO LOCKS THE TRANSMISSION INTO 5TH GEAR, MAKING IT DIFFICULT TO SLOW DOWN PROPERLY AND ACCELERATE FROM A STOP OR SLOW SPEED. THESE TWO ISSUES COMBINE MAKES THE VEHICLE A DANGER TO DRIVE. I DO NOT FEEL SAFE ANYMORE TAKING THIS VEHICLE ANYWHERE AND CANNOT TRUST IT. I HAVE CONTACTED FORD MOTOR COMPANY BOTH LOCALLY AND AT ITS HEADQUARTERS. THEIR REPLY IS THAT THEY HAVE TO FIX IT. I WAS TOLD TO CONTACT THE NHTSA FOR FURTHER HELP FROM A FRIEND WHO ENCOUNTERED SIMILAR ISSUES WITH FORD MOTOR COMPANY. THANK YOU FOR YOUR HELP.
WHILE DRIVING VECHICLE SUDDENINGLY LOST POWER, THIS IS THE SECOND TIME THIS HAS HAPPENED IN THE LAST 7700 MILES. VERY DANGEROUS AS THIS HAS HAPPENED IN HEAVEY TRAFFIC AND ALMOST CAUSED AN ACCIDENT. TRUCK HAS THE ECBOOSTENGINE. ## VIN PASSED ## 2012 FORD F150 ##
VEHICLE HAS LESS THAN 45000 MILES. HAS ERRATIC LOSS OF POWER WHILE ACCELERATING. EVIDENCE OF WATER IN THE AIR INTAKE. RESEARCH IS SHOWING THAT THE ECOBOOST ENGINE IS COLLECTING MORE WATER IN THE INTERCOOLER THAN THE ENGINE CAN CONSUME. PROBLEMS INCREASES IN SOUTHERN HUMID STATES. THIS IS PROBLEM CAUSED BY FAULTY ENGINEERING…
Read full complaint
VEHICLE HAS LESS THAN 45000 MILES. HAS ERRATIC LOSS OF POWER WHILE ACCELERATING. EVIDENCE OF WATER IN THE AIR INTAKE. RESEARCH IS SHOWING THAT THE ECOBOOST ENGINE IS COLLECTING MORE WATER IN THE INTERCOOLER THAN THE ENGINE CAN CONSUME. PROBLEMS INCREASES IN SOUTHERN HUMID STATES. THIS IS PROBLEM CAUSED BY FAULTY ENGINEERING IN THE 3.5L ECOBOOST ENGINE AND COULD CAUSE ACCIDENTS DUE TO UNPREDICTABLE LOSS IN POWER. LOSS OF POWER IS FELT WHILE DRIVING ON CITY AND HIGHWAY DRIVING.
WE HAVE A FORD F-150 AND IT IS LOSING POWER AS YOU TRAVEL DOWN THE ROAD. WE HAVE TO PULL OVER AND TURN THE TRUCK OFF AND RESTART IT. WE HAVE HAD IT IN THE SHOP AT LEAST TWICE WITH NO SUCCESS IN FINDING THE PROBLEM. WE HAVE HAD SENSORS REPLACED AND THE INTERCOOLER DRAINED TWICE. THIS IS DANGEROUS BECAUSE AS YOUR TRAVELING IT WILL…
Read full complaint
WE HAVE A FORD F-150 AND IT IS LOSING POWER AS YOU TRAVEL DOWN THE ROAD. WE HAVE TO PULL OVER AND TURN THE TRUCK OFF AND RESTART IT. WE HAVE HAD IT IN THE SHOP AT LEAST TWICE WITH NO SUCCESS IN FINDING THE PROBLEM. WE HAVE HAD SENSORS REPLACED AND THE INTERCOOLER DRAINED TWICE. THIS IS DANGEROUS BECAUSE AS YOUR TRAVELING IT WILL LOOSE POWER AND IT'S HARD TO GET OFF THE ROAD SOMETIMES AND COULD CAUSE AN ACCIDENT. WE DON'T KNOW WHAT TO DO AT THIS POINT.
Official recalls
419V075000 · Power Train:automatic Transmission; Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
Feb 11, 2019
Ford Motor Company (Ford) is recalling certain 2011-2013 F-150 vehicles equipped with a 6-speed automatic transmission. The transmission may unexpectedly downshift into first gear, regardless of vehicle speed.
Consequence & remedy
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began March 4, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S07.
Additional source detail variants (2)
Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
Ford Motor Company (Ford) is recalling certain 2011-2013 F-150 vehicles equipped with a 6-speed automatic transmission. The transmission may unexpectedly downshift into first gear, regardless of vehicle speed.
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began March 4, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S07.
Power Train:automatic Transmission
Ford Motor Company (Ford) is recalling certain 2011-2013 F-150 vehicles equipped with a 6-speed automatic transmission. The transmission may unexpectedly downshift into first gear, regardless of vehicle speed.
Consequence: Unexpectedly downshifting into first gear may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module, free of charge. The recall began March 4, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S07.
16V248000 · Power Train:automatic Transmission
Apr 27, 2016
Ford Motor Company (Ford) is recalling certain model year 2011-2012 Ford F-150 trucks, 2012 Ford Expedition, Lincoln Navigator, and Ford Mustang vehicles. The affected vehicles are equipped with an automatic transmission that may unexpectedly downshift to first gear, regardless of vehicle speed.
Consequence & remedy
Consequence: An unexpected downshift into first gear can cause the vehicle to slow down suddenly without warning and the rear tires may slide or lock, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will reprogram the powertrain control module with updated software, free of charge. The recall began on September 19, 2016. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S19.
12V190000 · Exterior Lighting:back Up Lights; Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
May 3, 2012
FORD IS RECALLING CERTAIN MODEL YEAR 2011-2012 FORD F-150, 2012 EXPEDITION AND LINCOLN NAVIGATOR, AND 2012-2013 MUSTANG VEHICLES, FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 102, "TRANSMISSION SHIFT LEVER SEQUENCE, STARTER INTERLOCK, AND TRANSMISSION BRAKING EFFECT" AND 108 LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT. THESE VEHICLES MAY HAVE A TRANSMISSION RANGE SENSOR (TRS) THAT WAS CALIBRATED OUT OF SPECIFICATION FOR REVERSE GEAR.
Consequence & remedy
Consequence: IF THIS CONDITION EXISTS, THE TRANSMISSION MAY NOT GO INTO REVERSE OR WHEN THE DRIVER PUSHES THE SHIFT LEVER IN THE REVERSE R POSITION AND THE VEHICLES TRANSMISSION DOES GO IN REVERSE, THE R MAY NOT ILLUMINATE ON THE DASHBOARD OF THE F-150, EXPEDITION, OR NAVIGATOR MODELS AND/OR THE BACKUP LAMP ON THE REAR OF THE F-150, EXPEDITION, NAVIGATOR, OR MUSTANG VEHICLES MAY NOT ILLUMINATE. THESE CONDITIONS INCREASE THE RISK OF A CRASH OR A PEDESTRIAN BEING STRUCK DUE TO THE VEHICLES NOT SIGNALING IT IS IN REVERSE.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT AND REPLACE THE TRS AS NECESSARY, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 11, 2012. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
Additional source detail variants (2)
Exterior Lighting:back Up Lights
FORD IS RECALLING CERTAIN MODEL YEAR 2011-2012 FORD F-150, 2012 EXPEDITION AND LINCOLN NAVIGATOR, AND 2012-2013 MUSTANG VEHICLES, FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 102, "TRANSMISSION SHIFT LEVER SEQUENCE, STARTER INTERLOCK, AND TRANSMISSION BRAKING EFFECT" AND 108 LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT. THESE VEHICLES MAY HAVE A TRANSMISSION RANGE SENSOR (TRS) THAT WAS CALIBRATED OUT OF SPECIFICATION FOR REVERSE GEAR.
Consequence: IF THIS CONDITION EXISTS, THE TRANSMISSION MAY NOT GO INTO REVERSE OR WHEN THE DRIVER PUSHES THE SHIFT LEVER IN THE REVERSE R POSITION AND THE VEHICLES TRANSMISSION DOES GO IN REVERSE, THE R MAY NOT ILLUMINATE ON THE DASHBOARD OF THE F-150, EXPEDITION, OR NAVIGATOR MODELS AND/OR THE BACKUP LAMP ON THE REAR OF THE F-150, EXPEDITION, NAVIGATOR, OR MUSTANG VEHICLES MAY NOT ILLUMINATE. THESE CONDITIONS INCREASE THE RISK OF A CRASH OR A PEDESTRIAN BEING STRUCK DUE TO THE VEHICLES NOT SIGNALING IT IS IN REVERSE.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT AND REPLACE THE TRS AS NECESSARY, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 11, 2012. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
FORD IS RECALLING CERTAIN MODEL YEAR 2011-2012 FORD F-150, 2012 EXPEDITION AND LINCOLN NAVIGATOR, AND 2012-2013 MUSTANG VEHICLES, FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NOS. 102, "TRANSMISSION SHIFT LEVER SEQUENCE, STARTER INTERLOCK, AND TRANSMISSION BRAKING EFFECT" AND 108 LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT. THESE VEHICLES MAY HAVE A TRANSMISSION RANGE SENSOR (TRS) THAT WAS CALIBRATED OUT OF SPECIFICATION FOR REVERSE GEAR.
Consequence: IF THIS CONDITION EXISTS, THE TRANSMISSION MAY NOT GO INTO REVERSE OR WHEN THE DRIVER PUSHES THE SHIFT LEVER IN THE REVERSE R POSITION AND THE VEHICLES TRANSMISSION DOES GO IN REVERSE, THE R MAY NOT ILLUMINATE ON THE DASHBOARD OF THE F-150, EXPEDITION, OR NAVIGATOR MODELS AND/OR THE BACKUP LAMP ON THE REAR OF THE F-150, EXPEDITION, NAVIGATOR, OR MUSTANG VEHICLES MAY NOT ILLUMINATE. THESE CONDITIONS INCREASE THE RISK OF A CRASH OR A PEDESTRIAN BEING STRUCK DUE TO THE VEHICLES NOT SIGNALING IT IS IN REVERSE.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT AND REPLACE THE TRS AS NECESSARY, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JUNE 11, 2012. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
12V198000 · Air Bags:frontal:sensor/control MODULE-INACTIVE
May 3, 2012
FORD IS RECALLING CERTAIN MODEL YEAR 2012 F-150 VEHICLES MANUFACTURED FROM NOVEMBER 6, 2011, THROUGH NOVEMBER 15, 2011. INCORRECT SOFTWARE FOR THE OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) WAS INSTALLED ON THE VEHICLES EITHER AT THE TIME OF MANUFACTURING OR DURING THE COURSE OF REPLACEMENT OF THE MODULE AS PART OF A SERVICE REPAIR. UNDER CERTAIN DRIVING CONDITIONS, THE OCSM MAY MISCLASSIFY THE PASSENGER SEATS OCCUPANT SUCH THAT THE PASSENGER SIDE AIRBAG DOES NOT DEPLOY WHEN IT SHOULD, DOES NOT DEPLOY AS INTENDED, OR DEPLOYS WHEN IT SHOULD NOT.
Consequence & remedy
Consequence: A FAILURE TO DEPLOY, FAILURE TO DEPLOY AS INTENDED, OR A DEPLOYMENT WHEN NOT INTENDED, INCREASES THE RISK OF INJURY TO THE PASSENGER SIDE SEAT OCCUPANT.
Remedy: FORD WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE OCSM FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 21, 2012. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4RQ17010 · Unexpected Transmission Downshift
Opened Dec 25, 2017 · Closed Oct 22, 2019
Status: closed (inferred from source dates) · Power Train:automatic Transmission; Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of transmissions unexpectedly downshifting to a lower gear without input from the driver on model year (MY) 2011-2013 Ford F-150, Expedition and Navigator vehicles. ODI has received 455 unique reports related to the alleged problem that were not covered under a previous recall for this issue (16V-248).Expedition and Navigator complaint rates are lower than F-150 complaints. Of those 455 reports, 34.7% claimed that the rear wheels locked up when the transmission downshifted. There were 4 accident claims with no injuries. There are many instances where drivers report leaving their lane or the road because of this issue.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 783 unique reports related to the alleged problem. There were 6 accident claims with 3 injuries. Ford also submitted 1206 warranty claims related to transmission downshifting failures. The failure can occur at any time, but typically at higher speed, and include symptoms such as sudden transmission downshifting, loss of speedometer, erratic shifting of transmission, and transmission stuck in one gear. The failures typically occur without warning and may result in the rear wheels momentarily locking up. The driver often had to fully stop the vehicle and restart it to get the vehicle to shift properly.On February 2nd, 2019 Ford notified ODI that it would conduct a safety recall (19V-075) to remedy transmission downshifting failures on all 2011-2013 F-150 vehicles. Ford will also offer extended warranties to 2011-2013 Expedition and Navigator vehicles with the same issue. Per Ford, some vehicles may experience an intermittent loss of Transmission Output Speed Sensor (OSS) signal to the Powertrain Control Module (PCM), potentially resulting in a temporary unintended downshift into first gear. Ford will reprogram the PCM with software that will prevent an unintended downshift into first gear and illuminate the Malfunction Indicator Light in the event of an intermittent OSS signal loss.The recall action initiated by the manufacturer appears to address the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the identification (ODI) numbers found in the attached list.
Additional source detail variants (2)
Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of transmissions unexpectedly downshifting to a lower gear without input from the driver on model year (MY) 2011-2013 Ford F-150, Expedition and Navigator vehicles. ODI has received 455 unique reports related to the alleged problem that were not covered under a previous recall for this issue (16V-248).Expedition and Navigator complaint rates are lower than F-150 complaints. Of those 455 reports, 34.7% claimed that the rear wheels locked up when the transmission downshifted. There were 4 accident claims with no injuries. There are many instances where drivers report leaving their lane or the road because of this issue.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 783 unique reports related to the alleged problem. There were 6 accident claims with 3 injuries. Ford also submitted 1206 warranty claims related to transmission downshifting failures. The failure can occur at any time, but typically at higher speed, and include symptoms such as sudden transmission downshifting, loss of speedometer, erratic shifting of transmission, and transmission stuck in one gear. The failures typically occur without warning and may result in the rear wheels momentarily locking up. The driver often had to fully stop the vehicle and restart it to get the vehicle to shift properly.On February 2nd, 2019 Ford notified ODI that it would conduct a safety recall (19V-075) to remedy transmission downshifting failures on all 2011-2013 F-150 vehicles. Ford will also offer extended warranties to 2011-2013 Expedition and Navigator vehicles with the same issue. Per Ford, some vehicles may experience an intermittent loss of Transmission Output Speed Sensor (OSS) signal to the Powertrain Control Module (PCM), potentially resulting in a temporary unintended downshift into first gear. Ford will reprogram the PCM with software that will prevent an unintended downshift into first gear and illuminate the Malfunction Indicator Light in the event of an intermittent OSS signal loss.The recall action initiated by the manufacturer appears to address the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the identification (ODI) numbers found in the attached list.
Power Train:automatic Transmission
The Office of Defects Investigation (ODI) opened an investigation based on consumer allegations of transmissions unexpectedly downshifting to a lower gear without input from the driver on model year (MY) 2011-2013 Ford F-150, Expedition and Navigator vehicles. ODI has received 455 unique reports related to the alleged problem that were not covered under a previous recall for this issue (16V-248).Expedition and Navigator complaint rates are lower than F-150 complaints. Of those 455 reports, 34.7% claimed that the rear wheels locked up when the transmission downshifted. There were 4 accident claims with no injuries. There are many instances where drivers report leaving their lane or the road because of this issue.In response to ODI's Information Request (IR) letter, Ford Motor Company (Ford) responded with 783 unique reports related to the alleged problem. There were 6 accident claims with 3 injuries. Ford also submitted 1206 warranty claims related to transmission downshifting failures. The failure can occur at any time, but typically at higher speed, and include symptoms such as sudden transmission downshifting, loss of speedometer, erratic shifting of transmission, and transmission stuck in one gear. The failures typically occur without warning and may result in the rear wheels momentarily locking up. The driver often had to fully stop the vehicle and restart it to get the vehicle to shift properly.On February 2nd, 2019 Ford notified ODI that it would conduct a safety recall (19V-075) to remedy transmission downshifting failures on all 2011-2013 F-150 vehicles. Ford will also offer extended warranties to 2011-2013 Expedition and Navigator vehicles with the same issue. Per Ford, some vehicles may experience an intermittent loss of Transmission Output Speed Sensor (OSS) signal to the Powertrain Control Module (PCM), potentially resulting in a temporary unintended downshift into first gear. Ford will reprogram the PCM with software that will prevent an unintended downshift into first gear and illuminate the Malfunction Indicator Light in the event of an intermittent OSS signal loss.The recall action initiated by the manufacturer appears to address the safety risks of concern to ODI.Accordingly, the investigation is closed.The ODI reports cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the identification (ODI) numbers found in the attached list.
EA15006 · Brake Vacuum Pump Failure
Opened Oct 16, 2015 · Closed Apr 28, 2016
Status: closed (inferred from source dates) · Service Brakes, Electric; Service Brakes, Hydraulic:power Assist; Service Brakes, Hydraulic:power Assist:vacuum
On February 15, 2016, Ford Motor Company initiated Customer Satisfaction Program 15N05 to extend warranty coverage for the electric vacuum pump in certain model year (MY) 2011 through 2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines.The program extends coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through July 30, 2016 regardless of mileage.Ford's program covers all repairs related to electric vacuum pump (EVP) malfunctions including excessive noise, vibration, or change in brake pedal feel while applying the brakes at cold start. Ford states that the engine intake manifold is the primary source of vacuum for the brake booster and is fully compliant to motor vehicle safety standards without the supplemental vacuum supplied by the EVP.The company also contends that failure modes related to the EVP are progressive and provide warning to operators by way of noise and vibration before an operator to experience any temporary change in brake pedal feel.ODI's analysis of warranty data found that the majority of claims involved consumer concerns with EVP noise or vibration from the left front fender area when the vehicle is first started. Continued operation in this mode with pump motor noise will eventually result in the EVP seizing or becoming non-functional.Component failure analysis indicated that Ford and its supplier, Continental, identified a pump crank drive corrosion condition due to moisture entry through the vacuum intake.Corrosion damage to EVP internal components may eventually result in a blown fuse in the power distribution box and total loss of EVP function.Analysis of consumer complaints, field reports, and warranty data related to EVP failures found thatincidents predominantly occurred in driveways and parking lots in the periods immediately after cold engine starts.Many consumers operated their vehicle for some period of time with a blown EVP fuse without realizing that the pump had failed or that the vehicle had a brake system malfunction.Consumers who did experience braking performance issues reporteda temporary hard brake pedal condition at start-up followed by more consistent normal pedal feel after few seconds.On June 22, 2015, Ford developed a remedy procedure and issued TSB 15-0105 instructing dealers to replace the vacuum pump and install a new vacuum pump harness kit. In addition to reviewing test data submitted by Ford, ODI assessed safety risks associated with the alleged defect under various operating conditions, including: 1) baseline system performance with full engine and EVP vacuum available using exemplar parts, 2) disabled EVP and booster vacuum regulated to simulate worst case conditions for engine intake manifold vacuum supply to the brake booster (approximately 300 mbar); and 3) all source vacuum to the brake booster removed and Optimized Hydraulic Braking (OHB) mode active to represent complete loss of brake booster function (note: this condition is a more severe brake boost system failure mode than the alleged defect).ODI also analyzed all complaints and warranty claims to identify incidents alleging brake system performance concerns related to EVP failures.These analyses identified no brake performance issues or resulting changes in stopping distances either on highway or city traffic conditions.Two complaints alleging EVP malfunctions caused or contributed to rear-end collisions during attempted decelerations from road speeds are not believed to be related to the alleged defect.The EVP provides supplemental vacuum during initial start-up and idle
Additional source detail variants (3)
Service Brakes, Electric
On February 15, 2016, Ford Motor Company initiated Customer Satisfaction Program 15N05 to extend warranty coverage for the electric vacuum pump in certain model year (MY) 2011 through 2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines.The program extends coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through July 30, 2016 regardless of mileage.Ford's program covers all repairs related to electric vacuum pump (EVP) malfunctions including excessive noise, vibration, or change in brake pedal feel while applying the brakes at cold start. Ford states that the engine intake manifold is the primary source of vacuum for the brake booster and is fully compliant to motor vehicle safety standards without the supplemental vacuum supplied by the EVP.The company also contends that failure modes related to the EVP are progressive and provide warning to operators by way of noise and vibration before an operator to experience any temporary change in brake pedal feel.ODI's analysis of warranty data found that the majority of claims involved consumer concerns with EVP noise or vibration from the left front fender area when the vehicle is first started. Continued operation in this mode with pump motor noise will eventually result in the EVP seizing or becoming non-functional.Component failure analysis indicated that Ford and its supplier, Continental, identified a pump crank drive corrosion condition due to moisture entry through the vacuum intake.Corrosion damage to EVP internal components may eventually result in a blown fuse in the power distribution box and total loss of EVP function.Analysis of consumer complaints, field reports, and warranty data related to EVP failures found thatincidents predominantly occurred in driveways and parking lots in the periods immediately after cold engine starts.Many consumers operated their vehicle for some period of time with a blown EVP fuse without realizing that the pump had failed or that the vehicle had a brake system malfunction.Consumers who did experience braking performance issues reporteda temporary hard brake pedal condition at start-up followed by more consistent normal pedal feel after few seconds.On June 22, 2015, Ford developed a remedy procedure and issued TSB 15-0105 instructing dealers to replace the vacuum pump and install a new vacuum pump harness kit. In addition to reviewing test data submitted by Ford, ODI assessed safety risks associated with the alleged defect under various operating conditions, including: 1) baseline system performance with full engine and EVP vacuum available using exemplar parts, 2) disabled EVP and booster vacuum regulated to simulate worst case conditions for engine intake manifold vacuum supply to the brake booster (approximately 300 mbar); and 3) all source vacuum to the brake booster removed and Optimized Hydraulic Braking (OHB) mode active to represent complete loss of brake booster function (note: this condition is a more severe brake boost system failure mode than the alleged defect).ODI also analyzed all complaints and warranty claims to identify incidents alleging brake system performance concerns related to EVP failures.These analyses identified no brake performance issues or resulting changes in stopping distances either on highway or city traffic conditions.Two complaints alleging EVP malfunctions caused or contributed to rear-end collisions during attempted decelerations from road speeds are not believed to be related to the alleged defect.The EVP provides supplemental vacuum during initial start-up and idle
Service Brakes, Hydraulic:power Assist
On February 15, 2016, Ford Motor Company initiated Customer Satisfaction Program 15N05 to extend warranty coverage for the electric vacuum pump in certain model year (MY) 2011 through 2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines.The program extends coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through July 30, 2016 regardless of mileage.Ford's program covers all repairs related to electric vacuum pump (EVP) malfunctions including excessive noise, vibration, or change in brake pedal feel while applying the brakes at cold start. Ford states that the engine intake manifold is the primary source of vacuum for the brake booster and is fully compliant to motor vehicle safety standards without the supplemental vacuum supplied by the EVP.The company also contends that failure modes related to the EVP are progressive and provide warning to operators by way of noise and vibration before an operator to experience any temporary change in brake pedal feel.ODI's analysis of warranty data found that the majority of claims involved consumer concerns with EVP noise or vibration from the left front fender area when the vehicle is first started. Continued operation in this mode with pump motor noise will eventually result in the EVP seizing or becoming non-functional.Component failure analysis indicated that Ford and its supplier, Continental, identified a pump crank drive corrosion condition due to moisture entry through the vacuum intake.Corrosion damage to EVP internal components may eventually result in a blown fuse in the power distribution box and total loss of EVP function.Analysis of consumer complaints, field reports, and warranty data related to EVP failures found thatincidents predominantly occurred in driveways and parking lots in the periods immediately after cold engine starts.Many consumers operated their vehicle for some period of time with a blown EVP fuse without realizing that the pump had failed or that the vehicle had a brake system malfunction.Consumers who did experience braking performance issues reporteda temporary hard brake pedal condition at start-up followed by more consistent normal pedal feel after few seconds.On June 22, 2015, Ford developed a remedy procedure and issued TSB 15-0105 instructing dealers to replace the vacuum pump and install a new vacuum pump harness kit. In addition to reviewing test data submitted by Ford, ODI assessed safety risks associated with the alleged defect under various operating conditions, including: 1) baseline system performance with full engine and EVP vacuum available using exemplar parts, 2) disabled EVP and booster vacuum regulated to simulate worst case conditions for engine intake manifold vacuum supply to the brake booster (approximately 300 mbar); and 3) all source vacuum to the brake booster removed and Optimized Hydraulic Braking (OHB) mode active to represent complete loss of brake booster function (note: this condition is a more severe brake boost system failure mode than the alleged defect).ODI also analyzed all complaints and warranty claims to identify incidents alleging brake system performance concerns related to EVP failures.These analyses identified no brake performance issues or resulting changes in stopping distances either on highway or city traffic conditions.Two complaints alleging EVP malfunctions caused or contributed to rear-end collisions during attempted decelerations from road speeds are not believed to be related to the alleged defect.The EVP provides supplemental vacuum during initial start-up and idle
Service Brakes, Hydraulic:power Assist:vacuum
On February 15, 2016, Ford Motor Company initiated Customer Satisfaction Program 15N05 to extend warranty coverage for the electric vacuum pump in certain model year (MY) 2011 through 2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines.The program extends coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through July 30, 2016 regardless of mileage.Ford's program covers all repairs related to electric vacuum pump (EVP) malfunctions including excessive noise, vibration, or change in brake pedal feel while applying the brakes at cold start. Ford states that the engine intake manifold is the primary source of vacuum for the brake booster and is fully compliant to motor vehicle safety standards without the supplemental vacuum supplied by the EVP.The company also contends that failure modes related to the EVP are progressive and provide warning to operators by way of noise and vibration before an operator to experience any temporary change in brake pedal feel.ODI's analysis of warranty data found that the majority of claims involved consumer concerns with EVP noise or vibration from the left front fender area when the vehicle is first started. Continued operation in this mode with pump motor noise will eventually result in the EVP seizing or becoming non-functional.Component failure analysis indicated that Ford and its supplier, Continental, identified a pump crank drive corrosion condition due to moisture entry through the vacuum intake.Corrosion damage to EVP internal components may eventually result in a blown fuse in the power distribution box and total loss of EVP function.Analysis of consumer complaints, field reports, and warranty data related to EVP failures found thatincidents predominantly occurred in driveways and parking lots in the periods immediately after cold engine starts.Many consumers operated their vehicle for some period of time with a blown EVP fuse without realizing that the pump had failed or that the vehicle had a brake system malfunction.Consumers who did experience braking performance issues reporteda temporary hard brake pedal condition at start-up followed by more consistent normal pedal feel after few seconds.On June 22, 2015, Ford developed a remedy procedure and issued TSB 15-0105 instructing dealers to replace the vacuum pump and install a new vacuum pump harness kit. In addition to reviewing test data submitted by Ford, ODI assessed safety risks associated with the alleged defect under various operating conditions, including: 1) baseline system performance with full engine and EVP vacuum available using exemplar parts, 2) disabled EVP and booster vacuum regulated to simulate worst case conditions for engine intake manifold vacuum supply to the brake booster (approximately 300 mbar); and 3) all source vacuum to the brake booster removed and Optimized Hydraulic Braking (OHB) mode active to represent complete loss of brake booster function (note: this condition is a more severe brake boost system failure mode than the alleged defect).ODI also analyzed all complaints and warranty claims to identify incidents alleging brake system performance concerns related to EVP failures.These analyses identified no brake performance issues or resulting changes in stopping distances either on highway or city traffic conditions.Two complaints alleging EVP malfunctions caused or contributed to rear-end collisions during attempted decelerations from road speeds are not believed to be related to the alleged defect.The EVP provides supplemental vacuum during initial start-up and idle
PE15026 · Brake Vacuum Pump Failure
Opened Jun 22, 2015 · Closed Oct 19, 2015
Status: closed (inferred from source dates) · Service Brakes, Electric; Service Brakes, Hydraulic:power Assist; Service Brakes, Hydraulic:power Assist:vacuum
On June 22, 2015, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE15-026 to investigate incidents of increased brake pedal effort at cold start and extended stopping distance while driving in traffic, resulting from failures of the electric brake vacuum assist pump in model year (MY) 2011-2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines. In response to ODI's Information Request (IR) for PE15-026, Ford provided ODI with 396 complaints and field reports relating to incidents of increased brake pedal effort or malfunctions in the electric vacuum pump (EVP). ODI's analysis of the data provided by Ford identified 7 crashes and 1,851 warranty claims related to either a hard brake pedal condition or reduced brake effectiveness. Additionally, ODI identified one report in its database alleging an injury to an occupant of a vehicle struck in the rear by a subject F-150 vehicle with a failed EVP as documented in the police accident report referencing a dealer assessment of the pump.According to Ford, the subject vehicles utilize a traditional brake vacuum booster to provide power assist for braking and the EVP is intended to operate to maintain consistent brake pedal feel. The engine intake manifold is the primary source of vacuum for the booster and is fully compliant to motor vehicle safety standards without the EVP. Ford described the conditions related to a change in brake pedal feel as limited and temporary and provided component failure analysis showing evidence of water entry into the EVP which caused internal pump corrosion. Ford indicated that the EVP failure mode is progressive and provides warning to operators by way of noise and vibration before an operator is likely to experience any temporary change in brake pedal feel. Damage to the EVP motor bearing may eventually result in a blown EVP fuse and total loss of EVP function. Ford provided test data showing the brake pedal forces and pedal travel curves over time for 0.3g decelerations to a stop from 80kph (50mph) for: 1) normal system (full engine and EVP vacuum available); 2) Ford's approximation of worst case booster performance with EVP failure (EVP disabled and booster vacuum regulated to 300mbar to simulate cold start, all accessory loads on, and starting at 0 vacuum); and 3) with all source vacuum to the brake booster removed and Hydraulic Boost Compensation (HBC) active to represent complete loss of brake booster function. The Ford tests showed that the brake pedal forces required for achieving the 0.3g decelerations were relatively low for the normal condition, 35-40 N (8-9 lbf), increased by approximately 2-3 times normal when the EVP is disabled, 75-115 N (17-26 lbf), and increased by about 5-6 times normal for the complete brake booster failure condition, 205-215 N (46-48 lbf). This Preliminary Evaluation has been upgraded to Engineering Analysis (EA15-006) to test for EVP malfunctions under other vehicle operating conditions (e.g., low-speed driveway braking after cold-start with failed EVP), potential human factors contributions and to further assess the scope, frequency, and safety-related consequences of the alleged defect.The VOQs associated with the opening of this investigation are:10565994, 10575987, 10598351, 10604687, 10605701, 10607811, 10610491, 10615536, 10617828, 10619545, 10643075, 10650578, 10662151, 10664415, 10666988, 10668069, 10678844, 10695537, 10700874, 10706217, 10706271, 10712465, 10723033, 10723792, 10726960, 10730549, 10730721, 10730735, 10730837, 10730909, 10731008, 10731135, 10731157, 10731165, 10731395, 10731758, 10732609, 10732878, 10733375, 10733804, 10734558, 10734613, 10743859, 10744214, 10
Additional source detail variants (3)
Service Brakes, Electric
On June 22, 2015, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE15-026 to investigate incidents of increased brake pedal effort at cold start and extended stopping distance while driving in traffic, resulting from failures of the electric brake vacuum assist pump in model year (MY) 2011-2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines. In response to ODI's Information Request (IR) for PE15-026, Ford provided ODI with 396 complaints and field reports relating to incidents of increased brake pedal effort or malfunctions in the electric vacuum pump (EVP). ODI's analysis of the data provided by Ford identified 7 crashes and 1,851 warranty claims related to either a hard brake pedal condition or reduced brake effectiveness. Additionally, ODI identified one report in its database alleging an injury to an occupant of a vehicle struck in the rear by a subject F-150 vehicle with a failed EVP as documented in the police accident report referencing a dealer assessment of the pump.According to Ford, the subject vehicles utilize a traditional brake vacuum booster to provide power assist for braking and the EVP is intended to operate to maintain consistent brake pedal feel. The engine intake manifold is the primary source of vacuum for the booster and is fully compliant to motor vehicle safety standards without the EVP. Ford described the conditions related to a change in brake pedal feel as limited and temporary and provided component failure analysis showing evidence of water entry into the EVP which caused internal pump corrosion. Ford indicated that the EVP failure mode is progressive and provides warning to operators by way of noise and vibration before an operator is likely to experience any temporary change in brake pedal feel. Damage to the EVP motor bearing may eventually result in a blown EVP fuse and total loss of EVP function. Ford provided test data showing the brake pedal forces and pedal travel curves over time for 0.3g decelerations to a stop from 80kph (50mph) for: 1) normal system (full engine and EVP vacuum available); 2) Ford's approximation of worst case booster performance with EVP failure (EVP disabled and booster vacuum regulated to 300mbar to simulate cold start, all accessory loads on, and starting at 0 vacuum); and 3) with all source vacuum to the brake booster removed and Hydraulic Boost Compensation (HBC) active to represent complete loss of brake booster function. The Ford tests showed that the brake pedal forces required for achieving the 0.3g decelerations were relatively low for the normal condition, 35-40 N (8-9 lbf), increased by approximately 2-3 times normal when the EVP is disabled, 75-115 N (17-26 lbf), and increased by about 5-6 times normal for the complete brake booster failure condition, 205-215 N (46-48 lbf). This Preliminary Evaluation has been upgraded to Engineering Analysis (EA15-006) to test for EVP malfunctions under other vehicle operating conditions (e.g., low-speed driveway braking after cold-start with failed EVP), potential human factors contributions and to further assess the scope, frequency, and safety-related consequences of the alleged defect.The VOQs associated with the opening of this investigation are:10565994, 10575987, 10598351, 10604687, 10605701, 10607811, 10610491, 10615536, 10617828, 10619545, 10643075, 10650578, 10662151, 10664415, 10666988, 10668069, 10678844, 10695537, 10700874, 10706217, 10706271, 10712465, 10723033, 10723792, 10726960, 10730549, 10730721, 10730735, 10730837, 10730909, 10731008, 10731135, 10731157, 10731165, 10731395, 10731758, 10732609, 10732878, 10733375, 10733804, 10734558, 10734613, 10743859, 10744214, 10
Service Brakes, Hydraulic:power Assist
On June 22, 2015, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE15-026 to investigate incidents of increased brake pedal effort at cold start and extended stopping distance while driving in traffic, resulting from failures of the electric brake vacuum assist pump in model year (MY) 2011-2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines. In response to ODI's Information Request (IR) for PE15-026, Ford provided ODI with 396 complaints and field reports relating to incidents of increased brake pedal effort or malfunctions in the electric vacuum pump (EVP). ODI's analysis of the data provided by Ford identified 7 crashes and 1,851 warranty claims related to either a hard brake pedal condition or reduced brake effectiveness. Additionally, ODI identified one report in its database alleging an injury to an occupant of a vehicle struck in the rear by a subject F-150 vehicle with a failed EVP as documented in the police accident report referencing a dealer assessment of the pump.According to Ford, the subject vehicles utilize a traditional brake vacuum booster to provide power assist for braking and the EVP is intended to operate to maintain consistent brake pedal feel. The engine intake manifold is the primary source of vacuum for the booster and is fully compliant to motor vehicle safety standards without the EVP. Ford described the conditions related to a change in brake pedal feel as limited and temporary and provided component failure analysis showing evidence of water entry into the EVP which caused internal pump corrosion. Ford indicated that the EVP failure mode is progressive and provides warning to operators by way of noise and vibration before an operator is likely to experience any temporary change in brake pedal feel. Damage to the EVP motor bearing may eventually result in a blown EVP fuse and total loss of EVP function. Ford provided test data showing the brake pedal forces and pedal travel curves over time for 0.3g decelerations to a stop from 80kph (50mph) for: 1) normal system (full engine and EVP vacuum available); 2) Ford's approximation of worst case booster performance with EVP failure (EVP disabled and booster vacuum regulated to 300mbar to simulate cold start, all accessory loads on, and starting at 0 vacuum); and 3) with all source vacuum to the brake booster removed and Hydraulic Boost Compensation (HBC) active to represent complete loss of brake booster function. The Ford tests showed that the brake pedal forces required for achieving the 0.3g decelerations were relatively low for the normal condition, 35-40 N (8-9 lbf), increased by approximately 2-3 times normal when the EVP is disabled, 75-115 N (17-26 lbf), and increased by about 5-6 times normal for the complete brake booster failure condition, 205-215 N (46-48 lbf). This Preliminary Evaluation has been upgraded to Engineering Analysis (EA15-006) to test for EVP malfunctions under other vehicle operating conditions (e.g., low-speed driveway braking after cold-start with failed EVP), potential human factors contributions and to further assess the scope, frequency, and safety-related consequences of the alleged defect.The VOQs associated with the opening of this investigation are:10565994, 10575987, 10598351, 10604687, 10605701, 10607811, 10610491, 10615536, 10617828, 10619545, 10643075, 10650578, 10662151, 10664415, 10666988, 10668069, 10678844, 10695537, 10700874, 10706217, 10706271, 10712465, 10723033, 10723792, 10726960, 10730549, 10730721, 10730735, 10730837, 10730909, 10731008, 10731135, 10731157, 10731165, 10731395, 10731758, 10732609, 10732878, 10733375, 10733804, 10734558, 10734613, 10743859, 10744214, 10
Service Brakes, Hydraulic:power Assist:vacuum
On June 22, 2015, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE15-026 to investigate incidents of increased brake pedal effort at cold start and extended stopping distance while driving in traffic, resulting from failures of the electric brake vacuum assist pump in model year (MY) 2011-2012 Ford F-150 pickup trucks equipped with 3.5L GTDI engines. In response to ODI's Information Request (IR) for PE15-026, Ford provided ODI with 396 complaints and field reports relating to incidents of increased brake pedal effort or malfunctions in the electric vacuum pump (EVP). ODI's analysis of the data provided by Ford identified 7 crashes and 1,851 warranty claims related to either a hard brake pedal condition or reduced brake effectiveness. Additionally, ODI identified one report in its database alleging an injury to an occupant of a vehicle struck in the rear by a subject F-150 vehicle with a failed EVP as documented in the police accident report referencing a dealer assessment of the pump.According to Ford, the subject vehicles utilize a traditional brake vacuum booster to provide power assist for braking and the EVP is intended to operate to maintain consistent brake pedal feel. The engine intake manifold is the primary source of vacuum for the booster and is fully compliant to motor vehicle safety standards without the EVP. Ford described the conditions related to a change in brake pedal feel as limited and temporary and provided component failure analysis showing evidence of water entry into the EVP which caused internal pump corrosion. Ford indicated that the EVP failure mode is progressive and provides warning to operators by way of noise and vibration before an operator is likely to experience any temporary change in brake pedal feel. Damage to the EVP motor bearing may eventually result in a blown EVP fuse and total loss of EVP function. Ford provided test data showing the brake pedal forces and pedal travel curves over time for 0.3g decelerations to a stop from 80kph (50mph) for: 1) normal system (full engine and EVP vacuum available); 2) Ford's approximation of worst case booster performance with EVP failure (EVP disabled and booster vacuum regulated to 300mbar to simulate cold start, all accessory loads on, and starting at 0 vacuum); and 3) with all source vacuum to the brake booster removed and Hydraulic Boost Compensation (HBC) active to represent complete loss of brake booster function. The Ford tests showed that the brake pedal forces required for achieving the 0.3g decelerations were relatively low for the normal condition, 35-40 N (8-9 lbf), increased by approximately 2-3 times normal when the EVP is disabled, 75-115 N (17-26 lbf), and increased by about 5-6 times normal for the complete brake booster failure condition, 205-215 N (46-48 lbf). This Preliminary Evaluation has been upgraded to Engineering Analysis (EA15-006) to test for EVP malfunctions under other vehicle operating conditions (e.g., low-speed driveway braking after cold-start with failed EVP), potential human factors contributions and to further assess the scope, frequency, and safety-related consequences of the alleged defect.The VOQs associated with the opening of this investigation are:10565994, 10575987, 10598351, 10604687, 10605701, 10607811, 10610491, 10615536, 10617828, 10619545, 10643075, 10650578, 10662151, 10664415, 10666988, 10668069, 10678844, 10695537, 10700874, 10706217, 10706271, 10712465, 10723033, 10723792, 10726960, 10730549, 10730721, 10730735, 10730837, 10730909, 10731008, 10731135, 10731157, 10731165, 10731395, 10731758, 10732609, 10732878, 10733375, 10733804, 10734558, 10734613, 10743859, 10744214, 10
PE13018 · Reduced Power During Hard Acceleration
Opened May 22, 2013 · Closed Apr 7, 2014
Status: closed (inferred from source dates) · Engine; Engine And Engine Cooling
On May 22, 2013, the Office of Defects Investigation (ODI) opened PE13-018 to investigate 95 complaints alleging incidents of reduced engine power during hard accelerations in model year (MY) 2011 through 2013 Ford F-150 trucks.ODI was aware of three technical service bulletins (TSBs) issued by Ford for a condition that was related to moisture accumulation in the Charge Air Cooler (CAC) for the turbochargers.A Preliminary Evaluation was opened to gather information to assess whether the subject vehicles contain a safety related defect.The subject vehicles are powered by Ford?s 3.5L EcoBoost engine which uses twin turbochargers to obtain a balance of fuel economy and engine power based on the driver?s demand.When the driver requests more power from the engine, as in accelerating to pass, merge, ascend hills or haul a load the two turbochargers will spin up compressing the air which is then used to increase the power created by the combustion in the engine.The compressed air, which gains heat by the compression process, is passed through a Charge Air Cooler (CAC) which is designed to lower the temperature of the air in order to make the combustion process even more efficient (Figures 1 and 2).In response to ODI?s Information Request letter, Ford indicated that a misfire condition could occur after steady-speed operation under significantly humid and rainy conditions.Ford?s analysis found that under those conditions, condensation could form and accumulate on the inside of the CAC tubes which could then be ingested into the engine during particularly hard acceleration near wide-open throttle.An engine misfire of up to three cylinders could occur if the amount of condensed water released from the CAC exceeded the engine?s operating threshold for water ingestion.Ford noted that due to regulations set by the EPA, the powertrain software would disable up to two of the misfiring cylinders for no more than 30 seconds and until the driver tips out the throttle in order to protect the catalytic converter from damage. Ford?s testing of this condition on the subject vehicles showed that a vehicle experiencing such a condition would continue to maintain its speed as well as accelerate, albeit at a lower rate than expected by the driver.Similar results were obtained in testing done by NHTSA?s Vehicle Research and Testing Center in East Liberty, Ohio (Figure 6).In an ongoing process to address the problem Ford issued a series of TSBs where a deflector shield was installed onto the CAC (Figures 3, 4 and 5).In January 2014 Ford indicated that its data shows that the TSBs have been effective in resolving the problem, that for the MY 2013 vehicles their remedy is 100% effective and the latest TSBs for MY 2011 ? 2012 are 95% effective.The 525 complaints to ODI and the total 4,120 unique VIN complaints listed in the Failure Report are incidents of alleged reduced power or driveability symptoms and not all are necessarily related to the condition created by water ingestion.Reduced power conditions can occur for a variety of reasons including faults with ignition coils, spark plugs, a catalytic converter, the throttle body, turbocharger, fuel pump/filter, powertrain control module (hardware or software) or transmission shifting problems.Ford also noted that in a large number of warranty claims on the subject vehicles, the CAC was replaced or a TSB procedure was performed when the symptoms exhibited were inconsistent with a CAC water ingestion related issue.Given these circumstances, further use of the agency resources in this matter does not appear to be warranted.Accordingly, this investigation is closed.The closing of
Additional source detail variants (2)
Engine And Engine Cooling
On May 22, 2013, the Office of Defects Investigation (ODI) opened PE13-018 to investigate 95 complaints alleging incidents of reduced engine power during hard accelerations in model year (MY) 2011 through 2013 Ford F-150 trucks.ODI was aware of three technical service bulletins (TSBs) issued by Ford for a condition that was related to moisture accumulation in the Charge Air Cooler (CAC) for the turbochargers.A Preliminary Evaluation was opened to gather information to assess whether the subject vehicles contain a safety related defect.The subject vehicles are powered by Ford?s 3.5L EcoBoost engine which uses twin turbochargers to obtain a balance of fuel economy and engine power based on the driver?s demand.When the driver requests more power from the engine, as in accelerating to pass, merge, ascend hills or haul a load the two turbochargers will spin up compressing the air which is then used to increase the power created by the combustion in the engine.The compressed air, which gains heat by the compression process, is passed through a Charge Air Cooler (CAC) which is designed to lower the temperature of the air in order to make the combustion process even more efficient (Figures 1 and 2).In response to ODI?s Information Request letter, Ford indicated that a misfire condition could occur after steady-speed operation under significantly humid and rainy conditions.Ford?s analysis found that under those conditions, condensation could form and accumulate on the inside of the CAC tubes which could then be ingested into the engine during particularly hard acceleration near wide-open throttle.An engine misfire of up to three cylinders could occur if the amount of condensed water released from the CAC exceeded the engine?s operating threshold for water ingestion.Ford noted that due to regulations set by the EPA, the powertrain software would disable up to two of the misfiring cylinders for no more than 30 seconds and until the driver tips out the throttle in order to protect the catalytic converter from damage. Ford?s testing of this condition on the subject vehicles showed that a vehicle experiencing such a condition would continue to maintain its speed as well as accelerate, albeit at a lower rate than expected by the driver.Similar results were obtained in testing done by NHTSA?s Vehicle Research and Testing Center in East Liberty, Ohio (Figure 6).In an ongoing process to address the problem Ford issued a series of TSBs where a deflector shield was installed onto the CAC (Figures 3, 4 and 5).In January 2014 Ford indicated that its data shows that the TSBs have been effective in resolving the problem, that for the MY 2013 vehicles their remedy is 100% effective and the latest TSBs for MY 2011 ? 2012 are 95% effective.The 525 complaints to ODI and the total 4,120 unique VIN complaints listed in the Failure Report are incidents of alleged reduced power or driveability symptoms and not all are necessarily related to the condition created by water ingestion.Reduced power conditions can occur for a variety of reasons including faults with ignition coils, spark plugs, a catalytic converter, the throttle body, turbocharger, fuel pump/filter, powertrain control module (hardware or software) or transmission shifting problems.Ford also noted that in a large number of warranty claims on the subject vehicles, the CAC was replaced or a TSB procedure was performed when the symptoms exhibited were inconsistent with a CAC water ingestion related issue.Given these circumstances, further use of the agency resources in this matter does not appear to be warranted.Accordingly, this investigation is closed.The closing of
Engine
On May 22, 2013, the Office of Defects Investigation (ODI) opened PE13-018 to investigate 95 complaints alleging incidents of reduced engine power during hard accelerations in model year (MY) 2011 through 2013 Ford F-150 trucks.ODI was aware of three technical service bulletins (TSBs) issued by Ford for a condition that was related to moisture accumulation in the Charge Air Cooler (CAC) for the turbochargers.A Preliminary Evaluation was opened to gather information to assess whether the subject vehicles contain a safety related defect.The subject vehicles are powered by Ford?s 3.5L EcoBoost engine which uses twin turbochargers to obtain a balance of fuel economy and engine power based on the driver?s demand.When the driver requests more power from the engine, as in accelerating to pass, merge, ascend hills or haul a load the two turbochargers will spin up compressing the air which is then used to increase the power created by the combustion in the engine.The compressed air, which gains heat by the compression process, is passed through a Charge Air Cooler (CAC) which is designed to lower the temperature of the air in order to make the combustion process even more efficient (Figures 1 and 2).In response to ODI?s Information Request letter, Ford indicated that a misfire condition could occur after steady-speed operation under significantly humid and rainy conditions.Ford?s analysis found that under those conditions, condensation could form and accumulate on the inside of the CAC tubes which could then be ingested into the engine during particularly hard acceleration near wide-open throttle.An engine misfire of up to three cylinders could occur if the amount of condensed water released from the CAC exceeded the engine?s operating threshold for water ingestion.Ford noted that due to regulations set by the EPA, the powertrain software would disable up to two of the misfiring cylinders for no more than 30 seconds and until the driver tips out the throttle in order to protect the catalytic converter from damage. Ford?s testing of this condition on the subject vehicles showed that a vehicle experiencing such a condition would continue to maintain its speed as well as accelerate, albeit at a lower rate than expected by the driver.Similar results were obtained in testing done by NHTSA?s Vehicle Research and Testing Center in East Liberty, Ohio (Figure 6).In an ongoing process to address the problem Ford issued a series of TSBs where a deflector shield was installed onto the CAC (Figures 3, 4 and 5).In January 2014 Ford indicated that its data shows that the TSBs have been effective in resolving the problem, that for the MY 2013 vehicles their remedy is 100% effective and the latest TSBs for MY 2011 ? 2012 are 95% effective.The 525 complaints to ODI and the total 4,120 unique VIN complaints listed in the Failure Report are incidents of alleged reduced power or driveability symptoms and not all are necessarily related to the condition created by water ingestion.Reduced power conditions can occur for a variety of reasons including faults with ignition coils, spark plugs, a catalytic converter, the throttle body, turbocharger, fuel pump/filter, powertrain control module (hardware or software) or transmission shifting problems.Ford also noted that in a large number of warranty claims on the subject vehicles, the CAC was replaced or a TSB procedure was performed when the symptoms exhibited were inconsistent with a CAC water ingestion related issue.Given these circumstances, further use of the agency resources in this matter does not appear to be warranted.Accordingly, this investigation is closed.The closing of