IllustrationTL* THE CONTACT OWNS A 2006 FORD F-150 SUPER CREW CAB. THE CONTACT STATED THAT THE DRIVER'S SIDE WINDOW REGULATOR FAILED. THE VEHICLE WAS NOT TAKEN TO THE DEALER. THE MANUFACTURER WAS NOT NOTIFIED. THE FAILURE MILEAGE WAS 108,000.
2006 Ford F-150
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2006 Ford F-150 do not stand out strongly from the model-year median of 676.
About this comparison →How this year compares
Owner complaints by model year
Compare all F-150 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1150–25K
9025–50K
10150–75K
7475–100K
85100–150K
37150K+
502 reports with mileage · 83 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine And Engine Cooling. Review the 77 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 74 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes, Hydraulic. Review the 68 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
58 crash reports18 fire reports31 injury reports
What owners actually said
585 reportsTL* THE CONTACT OWNS A 2006 FORD F150. THE CONTACT STATED THAT WHILE DRIVING 30 MPH DURING A RAIN STORM AND DEPRESSING THE BRAKES, THE VEHICLE EXHIBITED AND UNUSUALLY LOUND DOUBLE CLUNKING NOISE AS THE VEHICLE SKIDDED AND FLIPPED OVER. THE VEHICLE DID NOT CRASH INTO ANY OTHER OBJECT. THE POLICE WERE NOTIFIED HOWEVER, A REPORT WA…
Read full complaint
TL* THE CONTACT OWNS A 2006 FORD F150. THE CONTACT STATED THAT WHILE DRIVING 30 MPH DURING A RAIN STORM AND DEPRESSING THE BRAKES, THE VEHICLE EXHIBITED AND UNUSUALLY LOUND DOUBLE CLUNKING NOISE AS THE VEHICLE SKIDDED AND FLIPPED OVER. THE VEHICLE DID NOT CRASH INTO ANY OTHER OBJECT. THE POLICE WERE NOTIFIED HOWEVER, A REPORT WAS NOT FILED. THE CONTACT SUSTAINED AN AMPUTATED ARM DURING THE CRASH. THE VEHICLE WAS TOWED BY THE POLICE AND WAS DEEMED AS DESTROYED. THE CONTACT MENTIONED THAT JUST PRIOR TO THE CRASH, THE VEHICLE WAS TAKEN TO FIRESTONE FOR MAINTENANCE AND THE REPLACEMENT OF THE ROTOR AND FRONT BRAKE PAD. THE MANUFACTURER WAS NOT NOTIFIED OF THE INCIDENT. THE FAILURE MILEAGE WAS 78,912. UPDATED 2/4/13 *CN UPDATED 2/20/2013 *JS
THE BRAKES STARTED JUMPING WHEN I STARTED SLOWING DOWN AND SO I REPLACED THE BRAKES .. AND NOW EVEN WITH NEW BRAKE PADS THEY GO DOWN TO THE FLOOR. *TR
I AM 6'5" AND WEAR SIZE 16 SHOES. WITH MY SIZE AND THE DISTANCE TO THE PEDAL MY LEGS GO A LITTLE TO THE SIDE AND MY SHOE IS AT AN ANGLE TO THE PETALS LETS SAY 30 DEGREES. I WEARING TYPICAL WORK BOOT (LIKE IN FORD COMMERCIALS) WHICH THE LACES HAVE PEGS THE SHOE LACES GO AROUND. THESE PEGS ARE THE SAME AS ALL WORK BOOTS (RED WI…
Read full complaint
I AM 6'5" AND WEAR SIZE 16 SHOES. WITH MY SIZE AND THE DISTANCE TO THE PEDAL MY LEGS GO A LITTLE TO THE SIDE AND MY SHOE IS AT AN ANGLE TO THE PETALS LETS SAY 30 DEGREES. I WEARING TYPICAL WORK BOOT (LIKE IN FORD COMMERCIALS) WHICH THE LACES HAVE PEGS THE SHOE LACES GO AROUND. THESE PEGS ARE THE SAME AS ALL WORK BOOTS (RED WINGS - $300 BOOT). WHAT HAPPENED IS BECAUSE THE BRAKE PEDAL HAS A THICK RUBBER PAD THAT STRETCHES AROUND THE METAL BRAKE PEDAL AND LEAVES A RIDGE IN THE BACK OF THE PEDAL ALL THE WAY AROUND (SO THE RUBBER FITTING GOES OVER IT LIKE A SHOWER CAP). ALSO THE TRUCK IS AN AUTOMATIC AND THE BREAK PEDAL IS VERY LARGE. WHILE BACKING UP GIVING JUST A LITTLE GAS MY BOOT SHOE LACE PEG GOT TRAPPED BEHIND THE BRAKE PEDAL AND WAS HOLDING MY FOOT ON THE GAS PEDAL DEPRESSING IT DOWN. BECAUSE THE RUBBER RIDGE RUNS ALL THE WAY AROUND MY PEDAL (AS DESIGNED) I COULD NOT MOVE MY FOOT TO THE SIDE OF THE BRAKE PEDAL TO RELEASE THE GAS. BECAUSE OF THE THICKNESS OF MY FOOT WHEN I PRESSED THE BREAK WITH MY OTHER FOOT, IT MOVES THE GAS PEDAL DOWN AT THE SAME RATE AS MY FOOT IS TRAPPED, SO THE MORE YOU PRESS THE BRAKE THE MORE YOU GIVE GAS AT A RATIO THAT DOES NOT LET ME STOP THE VEHICLE. (NOTE I USE ONLY ONE FOOT FOR THE GAS AND BRAKE NORMALLY BUT WITH MY RIGHT FOOT TRAPPED I HAD NO OTHER CHOICE BUT TO USE MY LEFT FOOT TO BRAKE AND TRY TO GET IT THE TRUCK OUT OF GEAR . I COULD NOT DO ANYTHING IN TIME AND HIT A STATIONARY BUILDING. IF SOMEONE WAS BEHIND ME, THEY WOULD HAVE BEEN KILLED. THE ONLY OTHER WAY I COULD HAVE GOTTEN MY FOOT LOOSE IS TO DEPRESS THE GAS PEDAL WHICH IS NOT AN OPTION IN A LOT OF SITUATIONS BECAUSE IT WOULD MAKE THE SPEED OF THE IMPENDING IMPACT FASTER AND HARDER. THIS IS A DESIGN FLAW THAT TRAPS WORK BOOTS AND AT CERTAIN TIMES AND CAUSES LOOSE CONTROL. *TR
ACCORDING TO THE MODEL YEAR FORD F150 MAINTENANCE MANUAL, SPARK PLUGS ARE TO BE CHANGED EVERY 100,000MI. JUST PRIOR TO THIS MILEAGE FOR REMOVAL AND REPLACEMENT OF THE SPARK PLUGS THE ENGINE STARTED TO DEVELOP A MISFIRE. FORD HAS RECOGNIZED THE PROBLEM WITH THE SPARK PLUGS AND THE DIFFICULTY TO REMOVE THEM. THIS KNOWN MAINTENA…
Read full complaint
ACCORDING TO THE MODEL YEAR FORD F150 MAINTENANCE MANUAL, SPARK PLUGS ARE TO BE CHANGED EVERY 100,000MI. JUST PRIOR TO THIS MILEAGE FOR REMOVAL AND REPLACEMENT OF THE SPARK PLUGS THE ENGINE STARTED TO DEVELOP A MISFIRE. FORD HAS RECOGNIZED THE PROBLEM WITH THE SPARK PLUGS AND THE DIFFICULTY TO REMOVE THEM. THIS KNOWN MAINTENANCE ISSUE LED FORD TO PROVIDE A TSB ON THE ISSUE. THIS MISFIRE HAS ALMOST CAUSED ME TO STALL SEVERAL TIMES WHILE TOWING A 7,000LB BOAT. THIS IS DANGEROUS AND CREATES A SAFETY ISSUE FOR MYSELF AND THE MOTORISTS AROUND ME. I EXPRESS CONCERN THAT FORD SHOULD BE REPLACING THESE DEFECTIVE PLUGS WITH UPDATED DESIGNS BEFORE TRAGEDIES START TO HAPPEN. THIS ENGINE/SPARK PLUG DESIGN ENTERED SERVICE IN 2004 AND VEHICLES, LIKE MINE, WILL BEGIN TO EXPERIENCE SERIOUS SAFETY RELATED INCIDENTS IF IT IS NOT ADDRESSED. *TR
I WAS DRIVING TOWARDS WORK WHEN ALL THE SUDDEN THE TRUCK DIED. AFTER SAFELY PULLING ON THE SIDE OF THE ROAD. THE TRUCK DID NOT START AT ALL. ACCORDING TO MY FAMILY MECHANIC, IT WAS THE FUEL PUMP. I PAID 540 FOR THE FIX INCLUDING THE PART FROM THE FORD DEALERSHIP. A FEW DAYS LATER, THE TRUCK DID NOT START ON THE MORNING GOING TO…
Read full complaint
I WAS DRIVING TOWARDS WORK WHEN ALL THE SUDDEN THE TRUCK DIED. AFTER SAFELY PULLING ON THE SIDE OF THE ROAD. THE TRUCK DID NOT START AT ALL. ACCORDING TO MY FAMILY MECHANIC, IT WAS THE FUEL PUMP. I PAID 540 FOR THE FIX INCLUDING THE PART FROM THE FORD DEALERSHIP. A FEW DAYS LATER, THE TRUCK DID NOT START ON THE MORNING GOING TO WORK. MY FAMILY MECHANIC CAME AND DID A FEW TEST AND FOUND OUT IT WAS THE FUEL PUMP MODULE. HE THEN REPLACED SUCH MODULE. THE MODULE WAS RUSTED AND IT WAS FALLING APART. AFTER HE REPLACE IT WITH A NEW ONE, THE TRUCK STARTED AND IS WORKING PROPERLY. HE CHARGED ME 300 INCLUDING THE PART FROM THE DEALER. *TR
THE PASSENGER ASSIST HANDLE ATTACHED TO THE A PILLAR ON THE PASSENGER SIDE OF THE VEHICLE FAILED AT BOTH CONNECTION POINTS TO THE A PILLAR WHILE MY WIFE WAS ENTERING THE VEHICLE. MY WIFE WAS STANDING ON THE RUNNING BOARD AT THE TIME OF THE FAILURE OF THE ASSIST HANDLE, THE HANDLE COMPLETELY SEPARATED FROM THE VEHICLE AND SHE FE…
Read full complaint
THE PASSENGER ASSIST HANDLE ATTACHED TO THE A PILLAR ON THE PASSENGER SIDE OF THE VEHICLE FAILED AT BOTH CONNECTION POINTS TO THE A PILLAR WHILE MY WIFE WAS ENTERING THE VEHICLE. MY WIFE WAS STANDING ON THE RUNNING BOARD AT THE TIME OF THE FAILURE OF THE ASSIST HANDLE, THE HANDLE COMPLETELY SEPARATED FROM THE VEHICLE AND SHE FELL OFF THE RUNNING BOARD WITH THE HANDLE IN HER HAND, LANDING ON HER BACK AGAINST A CURB IN THE PARKING LOT. THIS IS THE THIRD FAILURE OF THIS PART SINCE THIS VEHICLE WAS PURCHASED NEW ON 10/06/2006. THE FIRST FAILURE OCCURRED WITHIN THE FIRST 12 MONTHS OF OWNERSHIP. THE SECOND FAILURE HAPPENED WITHIN THE FIRST 36 MONTHS OF OWNERSHIP. AFTER EACH INCIDENT, FORD REPLACED THE DEFECTIVE PART WITH AN IDENTICAL PART. THE FIRST TWO INCIDENTS DID NOT RESULT IN INJURY TO MY PASSENGER. FORTUNATELY, MY WIFE WAS NOT SERIOUSLY INJURED IN THE RECENT EVENT. *TR
I WAS DRIVING HOME AND SLOWED DOWN TO 15 MILES PER HR TO MAKE A LEFT HAND TURN AND HEARD A BIG BANG I DID NOT KNOW WHAT HAPPENED AT THE MOMENT I CONTINUED TO PROCEED ON AND THE NOISE WAS LOUD LIKE AN EXHAUST LEAK BUT TO COME FIND OUT THE NEXT TWO DAYS ON THINKING WHAT TO DO I PULLED OFF THE #4 PLUG IT WAS OUT OF THE MOTOR ALREAD…
Read full complaint
I WAS DRIVING HOME AND SLOWED DOWN TO 15 MILES PER HR TO MAKE A LEFT HAND TURN AND HEARD A BIG BANG I DID NOT KNOW WHAT HAPPENED AT THE MOMENT I CONTINUED TO PROCEED ON AND THE NOISE WAS LOUD LIKE AN EXHAUST LEAK BUT TO COME FIND OUT THE NEXT TWO DAYS ON THINKING WHAT TO DO I PULLED OFF THE #4 PLUG IT WAS OUT OF THE MOTOR ALREADY IT ACTUALLY BLEW OUT OF THE ENGINE. WHAT ARE MY RIGHTS IF ANY? *TR
ABS SENSOR SHORTED OUT AND FUSED TO WIRE HARNESS FOR WHOLE ELECTRICAL SYSTEM, FORD CLAIMS NO RECALL, COULD HAVE CAUSED MAJOR FIRE, NOTED COMPLAINT #10195595 WAS VERY SIMILAR. CAUSED $2300 DOLLAR REPAIR. *TR
TL* THE CONTACT OWNS A 2006 FORD F-150. THE CONTACT STATED THAT WHILE DRIVING 15 MPH, THE COVER TAIL GATE FELL AND DETACHED FROM THE VEHICLE. THE FAILURE RECURRED AND THE ENTIRE PART THAT COVERED THE TAIL GATE WAS MISSING. THE VEHICLE WAS TAKEN TO A REPAIR SHOP HOWEVER, THE VEHICLE WAS NOT REPAIRED AND THE PART WAS STILL MISSING…
Read full complaint
TL* THE CONTACT OWNS A 2006 FORD F-150. THE CONTACT STATED THAT WHILE DRIVING 15 MPH, THE COVER TAIL GATE FELL AND DETACHED FROM THE VEHICLE. THE FAILURE RECURRED AND THE ENTIRE PART THAT COVERED THE TAIL GATE WAS MISSING. THE VEHICLE WAS TAKEN TO A REPAIR SHOP HOWEVER, THE VEHICLE WAS NOT REPAIRED AND THE PART WAS STILL MISSING. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE BUT NO ASSISTANCE WAS PROVIDED. THE VIN WAS UNAVAILABLE. THE CURRENT AND FAILURE MILEAGE WAS 62,000.
Official recalls
411V107000 · Air Bags:frontal:driver Side:inflator Module
Feb 23, 2011
FORD IS RECALLING CERTAIN MODEL YEAR 2004-2006 F-150 PICK UP TRUCKS AS WELL AS CERTAIN MODEL YEAR 2006 LINCOLN MARK LT VEHICLES. IF THE CLOCKSPRING JUMPER WIRE COMES IN CONTACT WITH THE DRIVER SIDE FRONTAL AIR BAG LOWER HORN PLATE, THE WIRE INSULATION MAY BECOME CHAFED, CREATING A POTENTIAL FOR A SHORT CIRCUIT. IF THIS OCCURS THE AIR BAG WARNING LAMP MAY ILLUMINATE INDICATING THAT SERVICE IS REQUIRED.
Consequence & remedy
Consequence: THE DRIVER SIDE FRONTAL AIR BAG COULD INADVERTENTLY DEPLOY INCREASING THE RISK OF INJURY OR LOSS OF VEHICLE CONTROL IF OCCURRING WHILE IN MOTION.
Remedy: FORD WILL NOTIFY OWNERS AND INSTRUCT THEM TO TAKE THEIR VEHICLES TO A FORD OR LINCOLN/MERCURY DEALER TO HAVE A NEW CLOCKSPRING JUMPER WIRE INSTALLED THAT INCORPORATES A PROTECTIVE MESH COVER. REPAIRS WILL BE PERFORMED FREE OF CHARGE. THIS SAFETY RECALL BEGAN ON SOME VEHICLES IN MARCH 2011. THE RECALL CAMPAIGN ON THE EXPANDED POPULATION IS EXPECTED TO BEGIN ON OR ABOUT MAY 9, 2011. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
08V208000 · Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
May 7, 2008
FORD IS RECALLING 605,684 MY 2005-2006 F-150 AND LINCOLN MARK LT VEHICLES EQUIPPED WITH 5.4L 3-VALVE ENGINES. THE BRAKE BOOSTER VACUUM SUPPLY HOSE ATTACHED TO THE INTAKE MANIFOLD FITTING MAY SWELL OVER TIME AND LOSE RETENTION FORCE. THIS CONDITION COULD ALLOW THE HOSE TO BECOME DETACHED FROM THE FITTING DURING AN INTAKE MANIFOLD BACKFIRE. SHOULD THE HOSE DETACH FROM THE INTAKE MANIFOLD, SEVERAL BRAKE APPLICATIONS WITH POWER ASSIST WILL BE AVAILABLE BEFORE THE VACUUM RESERVE IS DEPLETED.
Consequence & remedy
Consequence: ONCE THE BRAKE BOOSTER VACUUM RESERVE IS DEPLETED, THE DRIVER WILL HAVE FOUNDATION BRAKE FUNCTION, BUT WITH INCREASED BRAKE PEDAL EFFORT. REDUCED VEHICLE BRAKING COULD LEAD TO A CRASH.
Remedy: DEALERS WILL REPLACE A RUBBER HOSE ON THE BRAKE BOOSTER VACUUM SUPPLY TUBE ASSEMBLY. THE RECALL BEGAN ON JUNE 27, 2008. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
06V033000 · Interior Lighting
Feb 6, 2006
CERTAIN PICKUP TRUCKS FAIL TO COMPLY WITH EITHER THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD (FMVSS) NO. 105, 'HYDRAULIC AND ELECTRIC BRAKE SYSTEMS' OR FMVSS NO. 135, 'PASSENGER CAR BRAKE SYSTEMS.' THESE VEHICLES WERE BUILT WITH A SOFTWARE ERROR IN THE INSTRUMENT CLUSTER.
Consequence & remedy
Consequence: THIS ERROR COULD PREVENT THE ANTILOCK BRAKE SYSTEM (ABS) WARNING LIGHT FROM ILLUMINATING IF THE ABS MODULE EVER BECAME INOPERATIVE.
Remedy: DEALERS WILL RECALIBRATE THE INSTRUMENT CLUSTER IN THESE VEHICLES. THE RECALL BEGAN ON FEBRUARY 27, 2006. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
05V520000 · Visibility:windshield Wiper/washer:motor
Nov 9, 2005
ON CERTAIN TRUCKS, PASSENGER CARS AND SPORT UTILITY VEHICLES, THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN PRODUCED WITHOUT GREASE BEING APPLIED TO THE OUTPUT SHAFT GEAR.
Consequence & remedy
Consequence: AFTER A PERIOD OF CONTINUOUS USE ON THE HIGH SPEED SETTING, LACK OF GREASE ON THE OUTPUT SHAFT GEAR MAY CAUSE THE GEAR TO DISTORT OR FRACTURE DURING OPERATION RESULTING IN A LOSS OF WIPER FUNCTION. INOPERATIVE WIPERS UNDER INCLEMENT WEATHER CONDITIONS COULD CAUSE A CRASH DUE TO IMPAIRED VISIBILITY.
Remedy: DEALERS WILL INSPECT THE WIPER MOTOR FOR THE PRESENCE OF GREASE AND GREASE THE WIPER MOTOR GEARS IF NECESSARY. THE RECALL BEGAN ON NOVEMBER 22, 2005. OWNERS MAY CONTACT FORD AT 1-800-392-3673 OR LINCOLN/MERCURY AT 1-800-521-4140.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA10001 · Inadvertent Airbag Deployment
Opened Jan 13, 2010 · Closed Apr 25, 2011
Status: closed (inferred from source dates) · Air Bags; Air Bags:frontal; Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:sensor/control MODULE-INACTIVE
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Additional source detail variants (4)
Air Bags
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal:driver Side:inflator Module
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal:sensor/control MODULE-INACTIVE
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
PE08001 · Loss Of Brake POWER-ASSIST
Opened Jan 8, 2008 · Closed May 9, 2008
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:power Assist; Service Brakes, Hydraulic:power Assist:vacuum; Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Additional source detail variants (3)
Service Brakes, Hydraulic:power Assist
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Service Brakes, Hydraulic:power Assist:vacuum
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.