NHTSA owner reports · September 18, 2026 snapshot.
Visibility complaints
17 reportsClear category filter60,000 miles · Jan 3, 2013
Electrical SystemVisibility
THE DRIVER'S SIDE WINDOW REGULATOR ON MY 2006 FORD F150 HAS BROKEN THREE TIMES, I WAS ABLE TO GET TWO REPLACED UNDER WARRANTY, BUT THE THIRD TIME HAPPENED THIS LAST MONTH, I AM REPLACING IT TODAY. I BELIEVE FROM MY EXPERIENCE, AND FROM THOUSANDS OF FORUM ENTRIES CITING THE SAME THING, THAT FORD SHOULD RECALL THIS PART. THIS PA…
Read full complaint
THE DRIVER'S SIDE WINDOW REGULATOR ON MY 2006 FORD F150 HAS BROKEN THREE TIMES, I WAS ABLE TO GET TWO REPLACED UNDER WARRANTY, BUT THE THIRD TIME HAPPENED THIS LAST MONTH, I AM REPLACING IT TODAY. I BELIEVE FROM MY EXPERIENCE, AND FROM THOUSANDS OF FORUM ENTRIES CITING THE SAME THING, THAT FORD SHOULD RECALL THIS PART. THIS PART IS GOING TO COST ME APPROXIMATELY $400.00 TO REPAIR. *TR
NHTSA ODI #10490934
108,000 miles · Dec 28, 2012
Visibility
TL* THE CONTACT OWNS A 2006 FORD F-150 SUPER CREW CAB. THE CONTACT STATED THAT THE DRIVER'S SIDE WINDOW REGULATOR FAILED. THE VEHICLE WAS NOT TAKEN TO THE DEALER. THE MANUFACTURER WAS NOT NOTIFIED. THE FAILURE MILEAGE WAS 108,000.
NHTSA ODI #10490310
65,000 miles · Jun 2, 2012
Electrical SystemVisibility
THE PASSENGER IN MY VEHICLE TRIED ROLLING UP THE WINDOW WHILE AT A STOPLIGHT AND IT WOULD NOT GO UP. THE WINDOW SWITCH WILL WORK TO ROLL THE WINDOW DOWN BUT NOT TO ROLL IT UP. AFTER APPROXIMATELY 11 MONTHS THE DRIVERS SIDE WINDOW IS DOING THE SAME THING, WILL GO DOWN BUT NOT UP. WITH THE WINDOW STUCK IN THE DOWN POSITION, MY VEH…
Read full complaint
THE PASSENGER IN MY VEHICLE TRIED ROLLING UP THE WINDOW WHILE AT A STOPLIGHT AND IT WOULD NOT GO UP. THE WINDOW SWITCH WILL WORK TO ROLL THE WINDOW DOWN BUT NOT TO ROLL IT UP. AFTER APPROXIMATELY 11 MONTHS THE DRIVERS SIDE WINDOW IS DOING THE SAME THING, WILL GO DOWN BUT NOT UP. WITH THE WINDOW STUCK IN THE DOWN POSITION, MY VEHICLE IS NOW EXPOSED TO THE ELEMENTS, RAIN PARTICULARLY, AND I FEAR THE WATER FROM THE RAIN IS GOING TO AFFECT THE REST OF MY DOOR SWITCHES, AND POSSIBLY RUIN THE LEATHER SEATS AND THE POWER FUNCTIONS FOR MY SEATS AS WELL. IT IS A DISTRACTION AND A HAZARD TO HAVE TO DRIVE WITH THE WINDOW DOWN CONSTANTLY. *TR
NHTSA ODI #10460377
53,000 miles · Sep 23, 2011
Visibility
TL* THE CONTACT OWNS A 2006 FORD F150. THE CONTACT STATED THAT ALL FOUR WINDOW REGULATORS FAILED AND AS A RESULT, SHE WAS UNABLE TO OPEN OR CLOSE THE WINDOW. AFTER SEVERAL ATTEMPTS, THE WINDOW WOULD OPEN HOWEVER, IT WOULD FAIL TO CLOSE. THE VEHICLE WAS TAKEN TO THE DEALER WHERE ALL FOUR WINDOW SWITCHES WERE REPLACED. THE MAN…
Read full complaint
TL* THE CONTACT OWNS A 2006 FORD F150. THE CONTACT STATED THAT ALL FOUR WINDOW REGULATORS FAILED AND AS A RESULT, SHE WAS UNABLE TO OPEN OR CLOSE THE WINDOW. AFTER SEVERAL ATTEMPTS, THE WINDOW WOULD OPEN HOWEVER, IT WOULD FAIL TO CLOSE. THE VEHICLE WAS TAKEN TO THE DEALER WHERE ALL FOUR WINDOW SWITCHES WERE REPLACED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE CURRENT MILEAGE WAS 57,900 AND THE APPROXIMATE FAILURE MILEAGE WAS 53,000.
NHTSA ODI #10426963
55,000 miles · Apr 11, 2010
Visibility
BOTH DRIVER AND PASSENGER SIDE REVIEW MIRRORS ARE NOT STATIONARY. THEY ARE LOOSE AND PIVOT WHEN CLOSING A DOOR. DRIVER'S SIDE ALSO VIBRATES WHILE DRIVING MAKING IT DIFFICULT TO SEE OUT OF. THIS HAS BEEN REPORTED TO FORD DEALERSHIP WHERE THEY STATED "IT IS JUST A POOR DESIGN WITH A 'BREAK-AWAY FEATURE' THAT APPEARS TO HAVE BEE…
Read full complaint
BOTH DRIVER AND PASSENGER SIDE REVIEW MIRRORS ARE NOT STATIONARY. THEY ARE LOOSE AND PIVOT WHEN CLOSING A DOOR. DRIVER'S SIDE ALSO VIBRATES WHILE DRIVING MAKING IT DIFFICULT TO SEE OUT OF. THIS HAS BEEN REPORTED TO FORD DEALERSHIP WHERE THEY STATED "IT IS JUST A POOR DESIGN WITH A 'BREAK-AWAY FEATURE' THAT APPEARS TO HAVE BEEN 'OVERWORN' BY PREVIOUS OWNER, POSSIBLY DUE TO USE OF THINNER GASKETS IN MIRROR ASSEMBLY". WHEN ASKED ABOUT LONGEVITY AND ANTICIPATED LIFESPAN OF MIRRORS PRIOR TO FAILURE DUE TO WEAR, THEY STATED IT WAS NOT A WEAR-PART, HOWEVER, THEY ALSO DENIED IT BEING DEFECTIVE AND QUOTED ME $1200 FOR PARTS AND LABOR TO REPLACE. WARRANTY WOULD NOT COVER SINCE THE DEFECT WAS MECHANICAL AND NOT ELECTRICAL. THE DEALERSHIP ALSO STATED THE MIRRORS THAT WOULD BE INSTALLED WOULD BE EXACTLY THE SAME AND THERE WAS NO GUARANTEE THIS WOULD NOT HAPPEN AGAIN. I WAS UNABLE TO GET A CORRECTIVE ACTION OR REASONING WHY MY PARTICULAR MIRRORS ARE NOT SATISFACTORY, BUT I HAVE HEARD THIS IS NOT A NEW PROBLEM FOR THIS VEHICLE. LOOKING AT BOTH OF MY MIRRORS, IT IS OBVIOUS THEY SHOULD HAVE SOME SORT OF LOCKING MECHANISM (SNAP-IN-PLACE DESIGN) LIKE MOST VEHICLES. THERE HAS NOT BEEN ANY ACCIDENT INVOLVED WITH THIS SAFETY ISSUE. THIS IS TO DOCUMENT A KNOWN PROBLEM FOR AWARENESS PURPOSES AND TO POTENTIALLY RECEIVE A CORRECTIVE ACTION FOR MY FAULTY MIRRORS. THIS ISSUE HAS BEEN ON-GOING, AND AN ARBITRARY INCIDENT DATE HAS BEEN ASSIGNED. *TR
NHTSA ODI #10324971
55,000 miles · Mar 2, 2010
Visibility
INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). POWER WINDOWS FOR THE F-150 NOT WORKING PROPERLY. I HAVE MANY FRIENDS WHO OWN THIS TYPE OF TRUCK AND THEY ARE COMPLAINING OF THE SAME THING. AND THE AVERAGE FIX IT PRICE IS $500. [XXX] *TR
NHTSA ODI #10315821
30,800 miles · Nov 29, 2009
Visibility
WINDOW FELL DOWN WHILE DRIVING ON THE FREEWAY. LOUD NOISE AS WINDOW FELL INSIDE THE DOOR I ALMOST CRASHED. VERY CLOSE CALL. I HAVE TALKED TO MANY OWNERS OF THIS SAME MODEL , DIFFERENT YEARS, ALL REPORT THE SAME PROBLEM. *TR
NHTSA ODI #10293921
42,000 miles · Oct 17, 2009
StructureVisibility
DRIVERS WINDOW CONTROL. *TR
NHTSA ODI #10288730
32,000 miles · Sep 24, 2009
Visibility
FAILURE OF THE DRIVERS SIDE POWER WINDOW SWITCH. OVER A MATTER OF MONTHS, THE OPERATION OF THE SWITCH DETERIORATED. INITIALLY, WHEN THE DRIVERS DOOR WINDOW SWITCH WAS PRESSED TO CLOSE, THE WINDOW WOULD HESITATE. THIS HESITATION BECAME WORSE UNTIL THE WINDOW WOULD NOT CLOSE WITHOUT REPEATED ATTEMPTS TO CLOSE THE WINDOW. AT TI…
Read full complaint
FAILURE OF THE DRIVERS SIDE POWER WINDOW SWITCH. OVER A MATTER OF MONTHS, THE OPERATION OF THE SWITCH DETERIORATED. INITIALLY, WHEN THE DRIVERS DOOR WINDOW SWITCH WAS PRESSED TO CLOSE, THE WINDOW WOULD HESITATE. THIS HESITATION BECAME WORSE UNTIL THE WINDOW WOULD NOT CLOSE WITHOUT REPEATED ATTEMPTS TO CLOSE THE WINDOW. AT TIMES, THE WINDOW HAD TO REMAIN OPEN OVERNIGHT AND AT SOME POINT IN TIME, THE CLOSE BUTTON WOULD WORK AGAIN. THERE WAS NO CLEAR INDICATOR TO A CONDITION THAT WOULD INITIATE THIS PROBLEM, NOR WAS THERE ANY PROCEDURE TO RETURN THE SWITCH TO OPERATION (ASIDE FROM REPEATED ATTEMPTS TO CLOSE THE WINDOW. THE MATTER WAS BROUGHT TOP THE ATTENTION OF FORD DURING THE FULL WARRANTY PERIOD AND THE DRIVERS DOOR WINDOW SWITCH ASSEMBLY REPLACED. THIS REPAIR APPEARS TO HAVE RESOLVED THE PROBLEM (IT HAS NOT OCCURRED SINCE). THIS INCIDENT IS BEING REPORTED AFTER LEARNING OF NUMEROUS OTHERS WHO HAVE EXPERIENCED THIS FAILURE. THESE CONVERSATIONS WERE WITH OTHERS OF F-150 AND OTHER FORD VEHICLES OF THE 2005-2006 ERA. A HIGH PERCENTAGE HAVE EXPERIENCED THIS PROBLEM. IF THE FAILURE OCCURRED UNDER THE 3YR/36,000 MILE WARRANTY, SWITCHES WERE NORMALLY REPLACED WITH NO COST TO THE VEHICLE OWNER. HOWEVER, M LARGE PORTION OF PEOPLE HAVE EXPERIENCED THIS CONDITION SHORTLY BEYOND THE WARRANTY PERIOD AND HAVE HAD TO LIVE WITH THE DEFECTIVE SWITCH OR PAY FOR REPLACEMENT. THE LARGE NUMBER OF PEOPLE WHO HAVE EXPERIENCED THIS FAILURE IS INDICATIVE OF A DEFECT IN THE SWITCH ASSEMBLY. *TR
NHTSA ODI #10285181
40,000 miles · Nov 5, 2008
Visibility
1. MY TRUCK WAS SITTING IN THE DRIVEWAY NOT BEING DRIVEN OR ANYTHING AND THE RIGHT REAR PASSENGER WINDOW FELL INTO THE DOOR. 2. IF THE WEATHER HAD NOT BEEN SO NICE MY TRUCK WOULD BE FULL OF WATER OR SNOW. 3. I PURCHASED THE EXTENDED WARRANTY SO IT IS GETTING REPLACED, BUT I HAVE READ ABOUT THIS FAILURE AND AM PLANNING O…
Read full complaint
1. MY TRUCK WAS SITTING IN THE DRIVEWAY NOT BEING DRIVEN OR ANYTHING AND THE RIGHT REAR PASSENGER WINDOW FELL INTO THE DOOR. 2. IF THE WEATHER HAD NOT BEEN SO NICE MY TRUCK WOULD BE FULL OF WATER OR SNOW. 3. I PURCHASED THE EXTENDED WARRANTY SO IT IS GETTING REPLACED, BUT I HAVE READ ABOUT THIS FAILURE AND AM PLANNING ON OWNING THIS TRUCK FOR LONG AFTER THE WARRANTY IS OVER WITH. IT SOUNDS LIKE EVEN IF THE PART IS FIXED THAT IT WILL FAIL AGAIN AND WILL CONTINUE TO FAIL UNTIL THE PART IS REPLACED WITH A STRONGER MORE SUITABLE PART THAT WILL STAND UP TO THE FORCES INVOLVED FOR THE LIFE OF THE VEHICLE INSTEAD OF JUST ABOUT 40K MILES AND UNTIL IT IS OUT OF WARRANTY. THIS PART IS CLOSE TO 400 BUCKS INSTALLED AND THE TRUCK HAS 4 WINDOWS. THAT IS A POTENTIAL OF 1600 BUCKS EVERY 40K MILES. I WOULD APPRECIATE A RECALL OR A SERVICE BULLETIN TO MAKE SURE THAT ALL OF US F150 OWNERS ARE PROTECTED AGAINST ALL THIS EXCESS COST. *TR
NHTSA ODI #10247720
Official recalls
4Feb 23, 2011
FORD IS RECALLING CERTAIN MODEL YEAR 2004-2006 F-150 PICK UP TRUCKS AS WELL AS CERTAIN MODEL YEAR 2006 LINCOLN MARK LT VEHICLES. IF THE CLOCKSPRING JUMPER WIRE COMES IN CONTACT WITH THE DRIVER SIDE FRONTAL AIR BAG LOWER HORN PLATE, THE WIRE INSULATION MAY BECOME CHAFED, CREATING A POTENTIAL FOR A SHORT CIRCUIT. IF THIS OCCURS THE AIR BAG WARNING LAMP MAY ILLUMINATE INDICATING THAT SERVICE IS REQUIRED.
Consequence & remedy
Consequence: THE DRIVER SIDE FRONTAL AIR BAG COULD INADVERTENTLY DEPLOY INCREASING THE RISK OF INJURY OR LOSS OF VEHICLE CONTROL IF OCCURRING WHILE IN MOTION.
Remedy: FORD WILL NOTIFY OWNERS AND INSTRUCT THEM TO TAKE THEIR VEHICLES TO A FORD OR LINCOLN/MERCURY DEALER TO HAVE A NEW CLOCKSPRING JUMPER WIRE INSTALLED THAT INCORPORATES A PROTECTIVE MESH COVER. REPAIRS WILL BE PERFORMED FREE OF CHARGE. THIS SAFETY RECALL BEGAN ON SOME VEHICLES IN MARCH 2011. THE RECALL CAMPAIGN ON THE EXPANDED POPULATION IS EXPECTED TO BEGIN ON OR ABOUT MAY 9, 2011. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
May 7, 2008
FORD IS RECALLING 605,684 MY 2005-2006 F-150 AND LINCOLN MARK LT VEHICLES EQUIPPED WITH 5.4L 3-VALVE ENGINES. THE BRAKE BOOSTER VACUUM SUPPLY HOSE ATTACHED TO THE INTAKE MANIFOLD FITTING MAY SWELL OVER TIME AND LOSE RETENTION FORCE. THIS CONDITION COULD ALLOW THE HOSE TO BECOME DETACHED FROM THE FITTING DURING AN INTAKE MANIFOLD BACKFIRE. SHOULD THE HOSE DETACH FROM THE INTAKE MANIFOLD, SEVERAL BRAKE APPLICATIONS WITH POWER ASSIST WILL BE AVAILABLE BEFORE THE VACUUM RESERVE IS DEPLETED.
Consequence & remedy
Consequence: ONCE THE BRAKE BOOSTER VACUUM RESERVE IS DEPLETED, THE DRIVER WILL HAVE FOUNDATION BRAKE FUNCTION, BUT WITH INCREASED BRAKE PEDAL EFFORT. REDUCED VEHICLE BRAKING COULD LEAD TO A CRASH.
Remedy: DEALERS WILL REPLACE A RUBBER HOSE ON THE BRAKE BOOSTER VACUUM SUPPLY TUBE ASSEMBLY. THE RECALL BEGAN ON JUNE 27, 2008. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
Feb 6, 2006
CERTAIN PICKUP TRUCKS FAIL TO COMPLY WITH EITHER THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD (FMVSS) NO. 105, 'HYDRAULIC AND ELECTRIC BRAKE SYSTEMS' OR FMVSS NO. 135, 'PASSENGER CAR BRAKE SYSTEMS.' THESE VEHICLES WERE BUILT WITH A SOFTWARE ERROR IN THE INSTRUMENT CLUSTER.
Consequence & remedy
Consequence: THIS ERROR COULD PREVENT THE ANTILOCK BRAKE SYSTEM (ABS) WARNING LIGHT FROM ILLUMINATING IF THE ABS MODULE EVER BECAME INOPERATIVE.
Remedy: DEALERS WILL RECALIBRATE THE INSTRUMENT CLUSTER IN THESE VEHICLES. THE RECALL BEGAN ON FEBRUARY 27, 2006. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
Nov 9, 2005
ON CERTAIN TRUCKS, PASSENGER CARS AND SPORT UTILITY VEHICLES, THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN PRODUCED WITHOUT GREASE BEING APPLIED TO THE OUTPUT SHAFT GEAR.
Consequence & remedy
Consequence: AFTER A PERIOD OF CONTINUOUS USE ON THE HIGH SPEED SETTING, LACK OF GREASE ON THE OUTPUT SHAFT GEAR MAY CAUSE THE GEAR TO DISTORT OR FRACTURE DURING OPERATION RESULTING IN A LOSS OF WIPER FUNCTION. INOPERATIVE WIPERS UNDER INCLEMENT WEATHER CONDITIONS COULD CAUSE A CRASH DUE TO IMPAIRED VISIBILITY.
Remedy: DEALERS WILL INSPECT THE WIPER MOTOR FOR THE PRESENCE OF GREASE AND GREASE THE WIPER MOTOR GEARS IF NECESSARY. THE RECALL BEGAN ON NOVEMBER 22, 2005. OWNERS MAY CONTACT FORD AT 1-800-392-3673 OR LINCOLN/MERCURY AT 1-800-521-4140.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA10001 · Inadvertent Airbag Deployment
Opened Jan 13, 2010 · Closed Apr 25, 2011
Status: closed (inferred from source dates) · Air Bags; Air Bags:frontal; Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:sensor/control MODULE-INACTIVE
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Additional source detail variants (4)
Air Bags
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal:driver Side:inflator Module
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal:sensor/control MODULE-INACTIVE
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
PE08001 · Loss Of Brake POWER-ASSIST
Opened Jan 8, 2008 · Closed May 9, 2008
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:power Assist; Service Brakes, Hydraulic:power Assist:vacuum; Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Additional source detail variants (3)
Service Brakes, Hydraulic:power Assist
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Service Brakes, Hydraulic:power Assist:vacuum
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Illustration