IllustrationTHE VEHICLE THAT IS TALKED ABOUT IN THIS IS A 2006 FORD F-150 THAT RECENTLY WENT IN FOR AN ANNUAL NYS SAFETY INSPECTION AND FAILED DUE TO AN EXCESSIVELY RUSTED FRAME THAT RESULTED IN CRACKS ON BOTH FRAME RAILS. THIS TRUCK HAS ONLY ~50,000 MILES AND IT IS UNKNOWN HOW LONG THE FRAME HAS ACTUALLY BEEN CRACKED AND STILL DRIVEN.
2006 Ford F-150
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2006 Ford F-150 do not stand out strongly from the model-year median of 676.
About this comparison →How this year compares
Owner complaints by model year
Compare all F-150 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1150–25K
9025–50K
10150–75K
7475–100K
85100–150K
37150K+
502 reports with mileage · 83 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine And Engine Cooling. Review the 77 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 74 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes, Hydraulic. Review the 68 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
58 crash reports18 fire reports31 injury reports
Structure complaints
44 reportsMY TRUCK CAUGHT ON FIRE YESTERDAY. DUE TO A HEAT SHIELD MISSING OVER PASSENGER SIDE CATALYTIC CONVERTER CAUSED THE PLASTIC GROMMETS THAT HOLD THE SOUND BARRIER MATERIAL ON THE FLOORBOARD TO DROP AND HANG ON TOP OF THE CATALYTIC CONVERTER UNTIL THE MATERIAL CAUGHT ON FIRE. MY INSURANCE COMPANY IS STILL INVESTIGATING HOW THE CATAL…
Read full complaint
MY TRUCK CAUGHT ON FIRE YESTERDAY. DUE TO A HEAT SHIELD MISSING OVER PASSENGER SIDE CATALYTIC CONVERTER CAUSED THE PLASTIC GROMMETS THAT HOLD THE SOUND BARRIER MATERIAL ON THE FLOORBOARD TO DROP AND HANG ON TOP OF THE CATALYTIC CONVERTER UNTIL THE MATERIAL CAUGHT ON FIRE. MY INSURANCE COMPANY IS STILL INVESTIGATING HOW THE CATALYTIC CONVERTER HEAT SHIELD WAS MISSING. LESS THAN A MONTH AFTER I BOUGHT THE TRUCK AND IT WAS USED, THEY HAD TO DO SERVICE WORK ON IT BECAUSE I PURCHASED THE TRUCK WITH A BROKEN FRONT COIL SPRING AND THE TRANSMISSION DIPSTICK TUBE HAD ROTTED. EVEN THOUGH THE TRUCK WAS MISSING A HEAT SHIELD, I BELIEVE THERE SHOULD BE ANY KIND OF FLAMMABLE MATERIAL NEAR THE CATALYTIC CONVERTER JUST IN CASE A HEAT SHIELD HAPPENS TO ROT AND FALL OFF OR FOR ANY REASON THE HEAT SHIELD IS MISSING .THE FIRE TRAVELED THROUGH THE MATERIAL ALMOST TO THE TOP OF MY ENGINE. AFTER I GOT THE FLAMES OUT IT WAS STILL SMOLDERING AND SMOLDERED UP INTO A SPACE I COULD NOT REACH TO NOR SEE. I ALSO BELIEVE A FIRE RETARDANT SYSTEM SHOULD BE CREATED TO DOUSE FLAMES IN A SECTION OF AN ENGINE COMPARTMENT THAT CANNOT BE REACHED AND WOULD PROBABLY SAVE COUNTLESS LIVES PROPERTY AND INVESTED MONEY INTO VEHICLE AND OTHER THINGS THAT A VEHICLE ON FIRE COULD DESTROY.
TL* THE CONTACT OWNS A 2006 FORD F-150. AFTER TAKING THE VEHICLE TO A DRIVE THRU CAR WASH SERVICE, WATER ENTERED THE PASSENGER SIDE. THE INTERIOR OF THE PASSENGER SIDE BECAME WET AND THE AIR BAG WARNING INDICATOR ILLUMINATED INTERMITTENTLY. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. …
Read full complaint
TL* THE CONTACT OWNS A 2006 FORD F-150. AFTER TAKING THE VEHICLE TO A DRIVE THRU CAR WASH SERVICE, WATER ENTERED THE PASSENGER SIDE. THE INTERIOR OF THE PASSENGER SIDE BECAME WET AND THE AIR BAG WARNING INDICATOR ILLUMINATED INTERMITTENTLY. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 98,000.
POWER STEERING HOSE RUST AND LEAKING-TRANSMISSION HOSES RUSTED AND LEAKING - SPARK PLUG BREAKING OFF WHEN HAVING THEM REPLACED
WHILE IN PASSING LANE OF THREE LANE WEST BOUND ROUTE 3 ENGINE SHUT DOWN, HAD TO NEGOTIATE TWO LANES OF HIGHWAY TRAFFIC TO GET TO SHOULDER WHILE COASTING. VEHICLE TOWED TO REPAIR SHOP. FUEL PUMP CONTROL MODULE FAILURE. MODULE CORRODED, HOLES THRU BACK OF MODULE WHERE IT MOUNTS TO FRAME. *TR
GAS AND BRAKE PEDAL ARE TOO CLOSE TOGETHER. YOU COULD STILL BE GIVING IT GAS WHILE YOU ARE PUSHING ON THE BRAKES. I SEE HUNDREDS OF COMPLAINTS ABOUT THIS ONLINE.I WAS PULLING INTO A PARKING SPOT WHEN I THOUGHT I WAS APPLYING THE BRAKES THE OTHER HALF OF MY FOOT WAS ON THE GAS CAUSING ME TO JUMP THE CURB AND CRASH INTO A WALL. *…
Read full complaint
GAS AND BRAKE PEDAL ARE TOO CLOSE TOGETHER. YOU COULD STILL BE GIVING IT GAS WHILE YOU ARE PUSHING ON THE BRAKES. I SEE HUNDREDS OF COMPLAINTS ABOUT THIS ONLINE.I WAS PULLING INTO A PARKING SPOT WHEN I THOUGHT I WAS APPLYING THE BRAKES THE OTHER HALF OF MY FOOT WAS ON THE GAS CAUSING ME TO JUMP THE CURB AND CRASH INTO A WALL. *TR
THE FRAME BROKE WHERE THE FRONT DIFFERENTIAL MOUNTS, THIS LET THE FRONT AXLE TWIST AND YOU CAN NOT STEER THE TRUCK!!! I THINK THIS IS VERY DANGEROUS, IF YOU WERE GOING OVER 5 MPH. YOU COULD NOT TURN.FORD FACTORY REP. SAYS THE TRUCK IS OUT OF WARRANTY SO NOT THERE PROBLEM, THEY WILL NOT DO ANYTHING ABOUT IT. FORD SHOULD FIX THIS …
Read full complaint
THE FRAME BROKE WHERE THE FRONT DIFFERENTIAL MOUNTS, THIS LET THE FRONT AXLE TWIST AND YOU CAN NOT STEER THE TRUCK!!! I THINK THIS IS VERY DANGEROUS, IF YOU WERE GOING OVER 5 MPH. YOU COULD NOT TURN.FORD FACTORY REP. SAYS THE TRUCK IS OUT OF WARRANTY SO NOT THERE PROBLEM, THEY WILL NOT DO ANYTHING ABOUT IT. FORD SHOULD FIX THIS AT THERE EXPENSE AS THIS A SAFETY CONCERN. HOW MANY OTHER FORD PICK UPS HAVE HAD THIS SAME PROBLEM BUT NOT REPORTED IT BECAUSE THEY DID NOT HOW TO OR WHO TO COMPLAIN TO. THE NTSB SHOULD LOOK INTO THIS VERY CAREFULLY TO SEE IF THIS IS A MAJOR PROBLEM. *TR
TRUCK WAS AT DEALERSHIP FOR REPAIRS, WHEN I WAS TOLD NOT TO HAVE REPAIRS DONE BECAUSE THE FRAME IS CRACKED AND RUSTED THRU. THEY SAID THE VEHICLE IS UNSAFE TO DRIVE. THE TRUCK IS NOW WORTHLESS. IN MY 50 YEARS OF OWNING AND DRIVING NUMEROUS VEHICLES IN THE NORTHEAST, I NEVER HAD A RUSTED FRAME ISSUE. FORD WILL NOT HELP NOR INVES…
Read full complaint
TRUCK WAS AT DEALERSHIP FOR REPAIRS, WHEN I WAS TOLD NOT TO HAVE REPAIRS DONE BECAUSE THE FRAME IS CRACKED AND RUSTED THRU. THEY SAID THE VEHICLE IS UNSAFE TO DRIVE. THE TRUCK IS NOW WORTHLESS. IN MY 50 YEARS OF OWNING AND DRIVING NUMEROUS VEHICLES IN THE NORTHEAST, I NEVER HAD A RUSTED FRAME ISSUE. FORD WILL NOT HELP NOR INVESTIGATE THE SITUATION. *TR
I AM 6'5" AND WEAR SIZE 16 SHOES. WITH MY SIZE AND THE DISTANCE TO THE PEDAL MY LEGS GO A LITTLE TO THE SIDE AND MY SHOE IS AT AN ANGLE TO THE PETALS LETS SAY 30 DEGREES. I WEARING TYPICAL WORK BOOT (LIKE IN FORD COMMERCIALS) WHICH THE LACES HAVE PEGS THE SHOE LACES GO AROUND. THESE PEGS ARE THE SAME AS ALL WORK BOOTS (RED WI…
Read full complaint
I AM 6'5" AND WEAR SIZE 16 SHOES. WITH MY SIZE AND THE DISTANCE TO THE PEDAL MY LEGS GO A LITTLE TO THE SIDE AND MY SHOE IS AT AN ANGLE TO THE PETALS LETS SAY 30 DEGREES. I WEARING TYPICAL WORK BOOT (LIKE IN FORD COMMERCIALS) WHICH THE LACES HAVE PEGS THE SHOE LACES GO AROUND. THESE PEGS ARE THE SAME AS ALL WORK BOOTS (RED WINGS - $300 BOOT). WHAT HAPPENED IS BECAUSE THE BRAKE PEDAL HAS A THICK RUBBER PAD THAT STRETCHES AROUND THE METAL BRAKE PEDAL AND LEAVES A RIDGE IN THE BACK OF THE PEDAL ALL THE WAY AROUND (SO THE RUBBER FITTING GOES OVER IT LIKE A SHOWER CAP). ALSO THE TRUCK IS AN AUTOMATIC AND THE BREAK PEDAL IS VERY LARGE. WHILE BACKING UP GIVING JUST A LITTLE GAS MY BOOT SHOE LACE PEG GOT TRAPPED BEHIND THE BRAKE PEDAL AND WAS HOLDING MY FOOT ON THE GAS PEDAL DEPRESSING IT DOWN. BECAUSE THE RUBBER RIDGE RUNS ALL THE WAY AROUND MY PEDAL (AS DESIGNED) I COULD NOT MOVE MY FOOT TO THE SIDE OF THE BRAKE PEDAL TO RELEASE THE GAS. BECAUSE OF THE THICKNESS OF MY FOOT WHEN I PRESSED THE BREAK WITH MY OTHER FOOT, IT MOVES THE GAS PEDAL DOWN AT THE SAME RATE AS MY FOOT IS TRAPPED, SO THE MORE YOU PRESS THE BRAKE THE MORE YOU GIVE GAS AT A RATIO THAT DOES NOT LET ME STOP THE VEHICLE. (NOTE I USE ONLY ONE FOOT FOR THE GAS AND BRAKE NORMALLY BUT WITH MY RIGHT FOOT TRAPPED I HAD NO OTHER CHOICE BUT TO USE MY LEFT FOOT TO BRAKE AND TRY TO GET IT THE TRUCK OUT OF GEAR . I COULD NOT DO ANYTHING IN TIME AND HIT A STATIONARY BUILDING. IF SOMEONE WAS BEHIND ME, THEY WOULD HAVE BEEN KILLED. THE ONLY OTHER WAY I COULD HAVE GOTTEN MY FOOT LOOSE IS TO DEPRESS THE GAS PEDAL WHICH IS NOT AN OPTION IN A LOT OF SITUATIONS BECAUSE IT WOULD MAKE THE SPEED OF THE IMPENDING IMPACT FASTER AND HARDER. THIS IS A DESIGN FLAW THAT TRAPS WORK BOOTS AND AT CERTAIN TIMES AND CAUSES LOOSE CONTROL. *TR
THE PASSENGER ASSIST HANDLE ATTACHED TO THE A PILLAR ON THE PASSENGER SIDE OF THE VEHICLE FAILED AT BOTH CONNECTION POINTS TO THE A PILLAR WHILE MY WIFE WAS ENTERING THE VEHICLE. MY WIFE WAS STANDING ON THE RUNNING BOARD AT THE TIME OF THE FAILURE OF THE ASSIST HANDLE, THE HANDLE COMPLETELY SEPARATED FROM THE VEHICLE AND SHE FE…
Read full complaint
THE PASSENGER ASSIST HANDLE ATTACHED TO THE A PILLAR ON THE PASSENGER SIDE OF THE VEHICLE FAILED AT BOTH CONNECTION POINTS TO THE A PILLAR WHILE MY WIFE WAS ENTERING THE VEHICLE. MY WIFE WAS STANDING ON THE RUNNING BOARD AT THE TIME OF THE FAILURE OF THE ASSIST HANDLE, THE HANDLE COMPLETELY SEPARATED FROM THE VEHICLE AND SHE FELL OFF THE RUNNING BOARD WITH THE HANDLE IN HER HAND, LANDING ON HER BACK AGAINST A CURB IN THE PARKING LOT. THIS IS THE THIRD FAILURE OF THIS PART SINCE THIS VEHICLE WAS PURCHASED NEW ON 10/06/2006. THE FIRST FAILURE OCCURRED WITHIN THE FIRST 12 MONTHS OF OWNERSHIP. THE SECOND FAILURE HAPPENED WITHIN THE FIRST 36 MONTHS OF OWNERSHIP. AFTER EACH INCIDENT, FORD REPLACED THE DEFECTIVE PART WITH AN IDENTICAL PART. THE FIRST TWO INCIDENTS DID NOT RESULT IN INJURY TO MY PASSENGER. FORTUNATELY, MY WIFE WAS NOT SERIOUSLY INJURED IN THE RECENT EVENT. *TR
Official recalls
411V107000 · Air Bags:frontal:driver Side:inflator Module
Feb 23, 2011
FORD IS RECALLING CERTAIN MODEL YEAR 2004-2006 F-150 PICK UP TRUCKS AS WELL AS CERTAIN MODEL YEAR 2006 LINCOLN MARK LT VEHICLES. IF THE CLOCKSPRING JUMPER WIRE COMES IN CONTACT WITH THE DRIVER SIDE FRONTAL AIR BAG LOWER HORN PLATE, THE WIRE INSULATION MAY BECOME CHAFED, CREATING A POTENTIAL FOR A SHORT CIRCUIT. IF THIS OCCURS THE AIR BAG WARNING LAMP MAY ILLUMINATE INDICATING THAT SERVICE IS REQUIRED.
Consequence & remedy
Consequence: THE DRIVER SIDE FRONTAL AIR BAG COULD INADVERTENTLY DEPLOY INCREASING THE RISK OF INJURY OR LOSS OF VEHICLE CONTROL IF OCCURRING WHILE IN MOTION.
Remedy: FORD WILL NOTIFY OWNERS AND INSTRUCT THEM TO TAKE THEIR VEHICLES TO A FORD OR LINCOLN/MERCURY DEALER TO HAVE A NEW CLOCKSPRING JUMPER WIRE INSTALLED THAT INCORPORATES A PROTECTIVE MESH COVER. REPAIRS WILL BE PERFORMED FREE OF CHARGE. THIS SAFETY RECALL BEGAN ON SOME VEHICLES IN MARCH 2011. THE RECALL CAMPAIGN ON THE EXPANDED POPULATION IS EXPECTED TO BEGIN ON OR ABOUT MAY 9, 2011. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
08V208000 · Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
May 7, 2008
FORD IS RECALLING 605,684 MY 2005-2006 F-150 AND LINCOLN MARK LT VEHICLES EQUIPPED WITH 5.4L 3-VALVE ENGINES. THE BRAKE BOOSTER VACUUM SUPPLY HOSE ATTACHED TO THE INTAKE MANIFOLD FITTING MAY SWELL OVER TIME AND LOSE RETENTION FORCE. THIS CONDITION COULD ALLOW THE HOSE TO BECOME DETACHED FROM THE FITTING DURING AN INTAKE MANIFOLD BACKFIRE. SHOULD THE HOSE DETACH FROM THE INTAKE MANIFOLD, SEVERAL BRAKE APPLICATIONS WITH POWER ASSIST WILL BE AVAILABLE BEFORE THE VACUUM RESERVE IS DEPLETED.
Consequence & remedy
Consequence: ONCE THE BRAKE BOOSTER VACUUM RESERVE IS DEPLETED, THE DRIVER WILL HAVE FOUNDATION BRAKE FUNCTION, BUT WITH INCREASED BRAKE PEDAL EFFORT. REDUCED VEHICLE BRAKING COULD LEAD TO A CRASH.
Remedy: DEALERS WILL REPLACE A RUBBER HOSE ON THE BRAKE BOOSTER VACUUM SUPPLY TUBE ASSEMBLY. THE RECALL BEGAN ON JUNE 27, 2008. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
06V033000 · Interior Lighting
Feb 6, 2006
CERTAIN PICKUP TRUCKS FAIL TO COMPLY WITH EITHER THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD (FMVSS) NO. 105, 'HYDRAULIC AND ELECTRIC BRAKE SYSTEMS' OR FMVSS NO. 135, 'PASSENGER CAR BRAKE SYSTEMS.' THESE VEHICLES WERE BUILT WITH A SOFTWARE ERROR IN THE INSTRUMENT CLUSTER.
Consequence & remedy
Consequence: THIS ERROR COULD PREVENT THE ANTILOCK BRAKE SYSTEM (ABS) WARNING LIGHT FROM ILLUMINATING IF THE ABS MODULE EVER BECAME INOPERATIVE.
Remedy: DEALERS WILL RECALIBRATE THE INSTRUMENT CLUSTER IN THESE VEHICLES. THE RECALL BEGAN ON FEBRUARY 27, 2006. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
05V520000 · Visibility:windshield Wiper/washer:motor
Nov 9, 2005
ON CERTAIN TRUCKS, PASSENGER CARS AND SPORT UTILITY VEHICLES, THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN PRODUCED WITHOUT GREASE BEING APPLIED TO THE OUTPUT SHAFT GEAR.
Consequence & remedy
Consequence: AFTER A PERIOD OF CONTINUOUS USE ON THE HIGH SPEED SETTING, LACK OF GREASE ON THE OUTPUT SHAFT GEAR MAY CAUSE THE GEAR TO DISTORT OR FRACTURE DURING OPERATION RESULTING IN A LOSS OF WIPER FUNCTION. INOPERATIVE WIPERS UNDER INCLEMENT WEATHER CONDITIONS COULD CAUSE A CRASH DUE TO IMPAIRED VISIBILITY.
Remedy: DEALERS WILL INSPECT THE WIPER MOTOR FOR THE PRESENCE OF GREASE AND GREASE THE WIPER MOTOR GEARS IF NECESSARY. THE RECALL BEGAN ON NOVEMBER 22, 2005. OWNERS MAY CONTACT FORD AT 1-800-392-3673 OR LINCOLN/MERCURY AT 1-800-521-4140.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA10001 · Inadvertent Airbag Deployment
Opened Jan 13, 2010 · Closed Apr 25, 2011
Status: closed (inferred from source dates) · Air Bags; Air Bags:frontal; Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:sensor/control MODULE-INACTIVE
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Additional source detail variants (4)
Air Bags
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal:driver Side:inflator Module
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal:sensor/control MODULE-INACTIVE
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
PE08001 · Loss Of Brake POWER-ASSIST
Opened Jan 8, 2008 · Closed May 9, 2008
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:power Assist; Service Brakes, Hydraulic:power Assist:vacuum; Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Additional source detail variants (3)
Service Brakes, Hydraulic:power Assist
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Service Brakes, Hydraulic:power Assist:vacuum
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.