IllustrationOIL PUMP/PRESSURE PROBLEM CAUSING KNOCKING AND ENGINE TO STOP. *TT
2006 Ford F-150
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2006 Ford F-150 do not stand out strongly from the model-year median of 676.
About this comparison →How this year compares
Owner complaints by model year
Compare all F-150 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1150–25K
9025–50K
10150–75K
7475–100K
85100–150K
37150K+
502 reports with mileage · 83 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine And Engine Cooling. Review the 77 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 74 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes, Hydraulic. Review the 68 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
58 crash reports18 fire reports31 injury reports
Engine complaints
74 reportsI WAS DRIVING DOWN US 281(BUSY 3 LANE HIGHWAY) IN SAN ANTONIO AND THE ENGINE SHUT OFF CAUSING ME TO COAST TO A STOP IN THE MIDDLE OF TRAFFIC. ONCE I GOT OFF OF THE ROAD, THE ENGINE STARTED UP LIKE NOTHING WAS WRONG. AFTER I INSPECTED THE FLUIDS AND SAW EVERYTHING CHECKED OUT, I GOT BACK ON THE HIGHWAY ONLY TO HAVE THE ENGINE S…
Read full complaint
I WAS DRIVING DOWN US 281(BUSY 3 LANE HIGHWAY) IN SAN ANTONIO AND THE ENGINE SHUT OFF CAUSING ME TO COAST TO A STOP IN THE MIDDLE OF TRAFFIC. ONCE I GOT OFF OF THE ROAD, THE ENGINE STARTED UP LIKE NOTHING WAS WRONG. AFTER I INSPECTED THE FLUIDS AND SAW EVERYTHING CHECKED OUT, I GOT BACK ON THE HIGHWAY ONLY TO HAVE THE ENGINE SHUT OFF AGAIN. I CALLED FORD TO SEE IF THERE WAS AN ISSUE REPORTED OR A RECALL, AND THERE WAS NOTHING. I FOUND OVER 300 COMPLAINTS ON VARIOUS FORUMS BY TYPING IN --2006 F150 FAILSAFE--IN THE SEARCH ENGINE. I THINK THIS IS A REAL SAFETY ISSUE THAT FORD NEEDS TO ADDRESS BEFORE SOMEONE GETS KILLED ON THE ROAD. [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *TR
WHEN STOPPED AT A RED LIGHT MY ENGINE BEGAN TO REV. AT VERY HIGH RPM'S AND THE TIRES BURNED OUT WHEN I SHIFTED THE TRANSMISSION INTO NEUTRAL. I PURCHASED THIS TRUCK IN DEC. 2013 AND THIS WAS APPROX. THE 7TH INCIDENT OF SUDDEN ACCELERATION. IT SEEMS TO ONLY HAPPEN WHEN STOOPED OR SLOWING DOWN. ANY HELP IN THIS MATTER WOULD BE DEE…
Read full complaint
WHEN STOPPED AT A RED LIGHT MY ENGINE BEGAN TO REV. AT VERY HIGH RPM'S AND THE TIRES BURNED OUT WHEN I SHIFTED THE TRANSMISSION INTO NEUTRAL. I PURCHASED THIS TRUCK IN DEC. 2013 AND THIS WAS APPROX. THE 7TH INCIDENT OF SUDDEN ACCELERATION. IT SEEMS TO ONLY HAPPEN WHEN STOOPED OR SLOWING DOWN. ANY HELP IN THIS MATTER WOULD BE DEEPLY APPRECIATED. THANKS IN ADVANCE. *TR
I BROUGHT MY TRUCK IN TO MY LOCAL FORD DEALER BECAUSE THE CHECK ENGINE LIGHT CAME ON. IT IS A 2006 F150 4.6L - AFTER HIS INSPECTION, THE MECHANIC STATED THAT THE BOTTOM OF THE #2 SPARK PLUG (MANUFACTURE INSTALLED) HAD DISINTEGRATED AND FELL INTO THE HEAD CAUSING SO MUCH DAMAGE TO THE #2 CYLINDER THAT I HAVE TO REPLACE THE EN…
Read full complaint
I BROUGHT MY TRUCK IN TO MY LOCAL FORD DEALER BECAUSE THE CHECK ENGINE LIGHT CAME ON. IT IS A 2006 F150 4.6L - AFTER HIS INSPECTION, THE MECHANIC STATED THAT THE BOTTOM OF THE #2 SPARK PLUG (MANUFACTURE INSTALLED) HAD DISINTEGRATED AND FELL INTO THE HEAD CAUSING SO MUCH DAMAGE TO THE #2 CYLINDER THAT I HAVE TO REPLACE THE ENTIRE ENGINE AT A COST OF OVER $6,000 PLUS TAX. IT WILL TAKE OVER A WEEK TO FIX AND I DO NOT HAVE ANOTHER VEHICLE. I WOULD LIKE FORD TO REIMBURSE ME FOR THE EXPENSE. I HAVE WRITTEN TO THEIR "CUSTOMER CARE"( [XXX]) DEPARTMENT, BUT HAVE HAD NO HELPFUL OR SATISFACTORY RESULTS. THIS IS A KNOWN ISSUE AS FORD HAS ISSUED A TSB AND DEVELOPED A TOOL TO ASSIST WITH THE REMOVAL OF FAULTY SPARK PLUGS. *TR
TL* THE CONTACT OWNS A 2006 FORD F-150. THE CONTACT STATED THAT THE VEHICLE WAS HESITANT TO ACCELERATION. THE VEHICLE WAS TAKEN TO A DEALER WHERE THE TECHNICIAN DIAGNOSED THAT THE SPARK PLUGS WERE DEFECTIVE AND NEEDED TO BE REPLACED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAG…
Read full complaint
TL* THE CONTACT OWNS A 2006 FORD F-150. THE CONTACT STATED THAT THE VEHICLE WAS HESITANT TO ACCELERATION. THE VEHICLE WAS TAKEN TO A DEALER WHERE THE TECHNICIAN DIAGNOSED THAT THE SPARK PLUGS WERE DEFECTIVE AND NEEDED TO BE REPLACED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS 90,000 AND THE CURRENT MILEAGE WAS UNKNOWN.
WENT TO START TRUCK AND ENGINE WOULD CRANK BUT WOULD NOT FIRE. I TRIED THE STARTING FLUID TEST TO SEE IF IT WAS AN IGNITION PROBLEM OR FUEL PROBLEM. GAVE A LITTLE SHOT OF STARTING FLUID INTO THE INTAKE AND THEN TRIED TO START. MOTOR ACTED LIKE IT WAS GOING TO START BUT NEVER STARTED BEINGS I DIDN'T GIVE IT ENOUGH STARTING FLUID …
Read full complaint
WENT TO START TRUCK AND ENGINE WOULD CRANK BUT WOULD NOT FIRE. I TRIED THE STARTING FLUID TEST TO SEE IF IT WAS AN IGNITION PROBLEM OR FUEL PROBLEM. GAVE A LITTLE SHOT OF STARTING FLUID INTO THE INTAKE AND THEN TRIED TO START. MOTOR ACTED LIKE IT WAS GOING TO START BUT NEVER STARTED BEINGS I DIDN'T GIVE IT ENOUGH STARTING FLUID TO START BECAUSE I'M NOT A FAN OF USING IT. WITH THAT I ELIMINATED THE IGNITION HAD TO BE FUEL. I GOT ON THE INTERNET AND SEARCHED NO START PROBLEM FOR 2006 F-150 AND FOUND A YOU TUBE VIDEO OF THE FUEL PUMP CONTROL MODULE RUSTING OUT. WENT OUT AND DROPPED SPARE TIRE AND TOOK THE CONTROL MODULE OFF THE CROSS MEMBER AND NOTICED THE HOLE CORRODED THROUGH THE HOUSING JUST LIKE THE VIDEO. I GOT THE UPGRADED PART FROM A FORD DEALER FOR $163 AND INSTALLED. RUNS FINE NOW. MY BIGGEST COMPLAINT IS FORD KNOWS THERE'S A PROBLEM SINCE THE HAVE CAME OUT WITH AN UPGRADED CONTROL MODULE SO WHY ISN'T THIS A RECALL? I LIVE IN A STATE THAT TEMPERATURES IN THE WINTER MONTHS CAN BE BELOW 0 DEGREES FAHRENHEIT AND DRIVE AN HOUR ONE WAY TO WORK, THIS COULD HAVE HAPPENED WHEN I WAS ON THE ROAD IN EXTREME COLD, COULD OF HAD MY TWO CHILDREN WITH ME BROKE DOWN ON THE SIDE OF THE ROAD AND COLD OUT. LUCKILY IT HAPPENED AT HOME BUT STILL IT WAS 4 DEGREES OUT AND LAYING UNDER MY TRUCK TAKING THE MODULE OFF WAS NOT VERY PLEASANT. THINK THIS IS SOMETHING THAT FORD NEEDS TO DO SOMETHING ABOUT. *TR
WHEN DRIVING HOME, CHECK ENGINE LIGHT STARTED FLASHING, IMMEDIATELY STOPPED AND HAD VEHICLE TOWED TO A WELL REPUTABLE SHOP FOR DIAGNOSIS AND REPAIR. WAS DIAGNOSED WITH TWO FUEL INJECTORS FAILING AND NEEDING REPLACED ALONG WITH ALL SPARK PLUGS NEEDED REPLACED. 6 OF THE 8 PLUGS SNAPPED IN HALF AND NEEDED TO BE BURROWED OUT ON T…
Read full complaint
WHEN DRIVING HOME, CHECK ENGINE LIGHT STARTED FLASHING, IMMEDIATELY STOPPED AND HAD VEHICLE TOWED TO A WELL REPUTABLE SHOP FOR DIAGNOSIS AND REPAIR. WAS DIAGNOSED WITH TWO FUEL INJECTORS FAILING AND NEEDING REPLACED ALONG WITH ALL SPARK PLUGS NEEDED REPLACED. 6 OF THE 8 PLUGS SNAPPED IN HALF AND NEEDED TO BE BURROWED OUT ON TOP OF IT COSTING $90 PER PLUG DRILLING OUT. TOTAL FOR REPAIRS CAME TO $2300. BUT AFTER REPAIRS WERE COMPLETED I STILL DO NOT HAVE A RUNNING VEHICLE. THE ENGINE STARTS BUT OIL PRESSURE DROPS AFTER 5 MINS OF RUNNING. I WOULD LOVE TO FIND A SOLUTION TO THIS, IF THIS IS COMMON OR NOT. AND IF SO, WHY IS IT NOT RECALLED? *TR
VEHICLE BEGAN TO SMELL LIKE GAS IN THE CAB ON NUMEROUS OCCASIONS. TOOK IT TO FORD DEALERSHIP MECHANIC AND WAS TOLD THAT THE SOURCE OF THE GAS SMELL COULD NOT BE FOUND. A FEW DAYS LATER UPON STARTING THE VEHICLE, A VERY LOUD EXPLOSIVE SOUND WAS HEARD UNDER THE HOOD. THE VEHICLE WAS TURNED OFF AND TOWED BACK TO THE FORD DEALERS…
Read full complaint
VEHICLE BEGAN TO SMELL LIKE GAS IN THE CAB ON NUMEROUS OCCASIONS. TOOK IT TO FORD DEALERSHIP MECHANIC AND WAS TOLD THAT THE SOURCE OF THE GAS SMELL COULD NOT BE FOUND. A FEW DAYS LATER UPON STARTING THE VEHICLE, A VERY LOUD EXPLOSIVE SOUND WAS HEARD UNDER THE HOOD. THE VEHICLE WAS TURNED OFF AND TOWED BACK TO THE FORD DEALERSHIP WHERE IT WAS DETERMINED THAT THE ORIGINAL #2 SPARK PLUG HAD BLOWN OUT OF THE ENGINE AND DAMAGED THE HEAD. REPAIR EXCEEDING $700 WITH ABSOLUTELY NO RESPONSIBILITY TAKEN BY FORD. REPEAT INCIDENT LESS THAN ONE YEAR LATER WITH ANOTHER CYLINDER. *TR
WHILE APPROACHING A STOP THE TRUCK GAUGES STARTED GOING CRAZY. TRUCK STALLED BUT RESTARTED WITH GAUGES STILL ACTING CRAZY. ALL GAUGES WOULD BOTTOM OUT AND COME BACK UP AND RADIO WAS TURNING ON AND OFF. REPLACED BATTERY BUT ONLY STALLING ISSUE WAS RESOLVED. TOOK TO LOCAL FORD DEALER BUT SINCE THE TRUCK ONLY DOES THIS RANDOMLY, TH…
Read full complaint
WHILE APPROACHING A STOP THE TRUCK GAUGES STARTED GOING CRAZY. TRUCK STALLED BUT RESTARTED WITH GAUGES STILL ACTING CRAZY. ALL GAUGES WOULD BOTTOM OUT AND COME BACK UP AND RADIO WAS TURNING ON AND OFF. REPLACED BATTERY BUT ONLY STALLING ISSUE WAS RESOLVED. TOOK TO LOCAL FORD DEALER BUT SINCE THE TRUCK ONLY DOES THIS RANDOMLY, THEY WERE NOT ABLE TO DIAGNOSE THE PROBLEM. TRUCK RUNS PERFECTLY BUT GAUGES AND RADIO STILL GO ON AND OFF MAKING IT EXTREMELY ANNOYING TO DRIVE. VERY FRUSTRATING TO KNOW THAT SO MANY OTHER FORD OWNERS HAVE THE SAME PROBLEM BUT NO SOLUTION HAS BEEN OFFERED FROM FORD. *TR
WHEN I STARTED THE TRUCK, A SPARK PLUG BLEW INTO THE HEAD. THE MECHANIC AT THE FORD DEALERSHIP TOLD ME THIS WAS A COMMON PROBLEM WITH THESE TRUCKS. THE REPAIR COST ME $3,448. TO REPLACE THE HEAD. IF FORD IS AWARE OF THIS PROBLEM, THE VEHICLES SHOULD BE RECALLED AND THE PROBLEM CORRECTED. MY FAMILY WAS LEFT STRANDED 7 HOURS A…
Read full complaint
WHEN I STARTED THE TRUCK, A SPARK PLUG BLEW INTO THE HEAD. THE MECHANIC AT THE FORD DEALERSHIP TOLD ME THIS WAS A COMMON PROBLEM WITH THESE TRUCKS. THE REPAIR COST ME $3,448. TO REPLACE THE HEAD. IF FORD IS AWARE OF THIS PROBLEM, THE VEHICLES SHOULD BE RECALLED AND THE PROBLEM CORRECTED. MY FAMILY WAS LEFT STRANDED 7 HOURS AWAY FROM HOME, HAD TO RENT A VEHICLE TO GET HOME AND THEN TWO WEEKS LATER, HAD TO RETURN TO DEALERSHIP AND PICK UP THE TRUCK. SO STRESSFUL AND EXPENSIVE. JUST GLAD WE WERE IN A TOWN WHEN THIS HAPPENED! *TR
Official recalls
411V107000 · Air Bags:frontal:driver Side:inflator Module
Feb 23, 2011
FORD IS RECALLING CERTAIN MODEL YEAR 2004-2006 F-150 PICK UP TRUCKS AS WELL AS CERTAIN MODEL YEAR 2006 LINCOLN MARK LT VEHICLES. IF THE CLOCKSPRING JUMPER WIRE COMES IN CONTACT WITH THE DRIVER SIDE FRONTAL AIR BAG LOWER HORN PLATE, THE WIRE INSULATION MAY BECOME CHAFED, CREATING A POTENTIAL FOR A SHORT CIRCUIT. IF THIS OCCURS THE AIR BAG WARNING LAMP MAY ILLUMINATE INDICATING THAT SERVICE IS REQUIRED.
Consequence & remedy
Consequence: THE DRIVER SIDE FRONTAL AIR BAG COULD INADVERTENTLY DEPLOY INCREASING THE RISK OF INJURY OR LOSS OF VEHICLE CONTROL IF OCCURRING WHILE IN MOTION.
Remedy: FORD WILL NOTIFY OWNERS AND INSTRUCT THEM TO TAKE THEIR VEHICLES TO A FORD OR LINCOLN/MERCURY DEALER TO HAVE A NEW CLOCKSPRING JUMPER WIRE INSTALLED THAT INCORPORATES A PROTECTIVE MESH COVER. REPAIRS WILL BE PERFORMED FREE OF CHARGE. THIS SAFETY RECALL BEGAN ON SOME VEHICLES IN MARCH 2011. THE RECALL CAMPAIGN ON THE EXPANDED POPULATION IS EXPECTED TO BEGIN ON OR ABOUT MAY 9, 2011. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.
08V208000 · Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
May 7, 2008
FORD IS RECALLING 605,684 MY 2005-2006 F-150 AND LINCOLN MARK LT VEHICLES EQUIPPED WITH 5.4L 3-VALVE ENGINES. THE BRAKE BOOSTER VACUUM SUPPLY HOSE ATTACHED TO THE INTAKE MANIFOLD FITTING MAY SWELL OVER TIME AND LOSE RETENTION FORCE. THIS CONDITION COULD ALLOW THE HOSE TO BECOME DETACHED FROM THE FITTING DURING AN INTAKE MANIFOLD BACKFIRE. SHOULD THE HOSE DETACH FROM THE INTAKE MANIFOLD, SEVERAL BRAKE APPLICATIONS WITH POWER ASSIST WILL BE AVAILABLE BEFORE THE VACUUM RESERVE IS DEPLETED.
Consequence & remedy
Consequence: ONCE THE BRAKE BOOSTER VACUUM RESERVE IS DEPLETED, THE DRIVER WILL HAVE FOUNDATION BRAKE FUNCTION, BUT WITH INCREASED BRAKE PEDAL EFFORT. REDUCED VEHICLE BRAKING COULD LEAD TO A CRASH.
Remedy: DEALERS WILL REPLACE A RUBBER HOSE ON THE BRAKE BOOSTER VACUUM SUPPLY TUBE ASSEMBLY. THE RECALL BEGAN ON JUNE 27, 2008. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
06V033000 · Interior Lighting
Feb 6, 2006
CERTAIN PICKUP TRUCKS FAIL TO COMPLY WITH EITHER THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD (FMVSS) NO. 105, 'HYDRAULIC AND ELECTRIC BRAKE SYSTEMS' OR FMVSS NO. 135, 'PASSENGER CAR BRAKE SYSTEMS.' THESE VEHICLES WERE BUILT WITH A SOFTWARE ERROR IN THE INSTRUMENT CLUSTER.
Consequence & remedy
Consequence: THIS ERROR COULD PREVENT THE ANTILOCK BRAKE SYSTEM (ABS) WARNING LIGHT FROM ILLUMINATING IF THE ABS MODULE EVER BECAME INOPERATIVE.
Remedy: DEALERS WILL RECALIBRATE THE INSTRUMENT CLUSTER IN THESE VEHICLES. THE RECALL BEGAN ON FEBRUARY 27, 2006. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
05V520000 · Visibility:windshield Wiper/washer:motor
Nov 9, 2005
ON CERTAIN TRUCKS, PASSENGER CARS AND SPORT UTILITY VEHICLES, THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN PRODUCED WITHOUT GREASE BEING APPLIED TO THE OUTPUT SHAFT GEAR.
Consequence & remedy
Consequence: AFTER A PERIOD OF CONTINUOUS USE ON THE HIGH SPEED SETTING, LACK OF GREASE ON THE OUTPUT SHAFT GEAR MAY CAUSE THE GEAR TO DISTORT OR FRACTURE DURING OPERATION RESULTING IN A LOSS OF WIPER FUNCTION. INOPERATIVE WIPERS UNDER INCLEMENT WEATHER CONDITIONS COULD CAUSE A CRASH DUE TO IMPAIRED VISIBILITY.
Remedy: DEALERS WILL INSPECT THE WIPER MOTOR FOR THE PRESENCE OF GREASE AND GREASE THE WIPER MOTOR GEARS IF NECESSARY. THE RECALL BEGAN ON NOVEMBER 22, 2005. OWNERS MAY CONTACT FORD AT 1-800-392-3673 OR LINCOLN/MERCURY AT 1-800-521-4140.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA10001 · Inadvertent Airbag Deployment
Opened Jan 13, 2010 · Closed Apr 25, 2011
Status: closed (inferred from source dates) · Air Bags; Air Bags:frontal; Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:sensor/control MODULE-INACTIVE
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Additional source detail variants (4)
Air Bags
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal:driver Side:inflator Module
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
Air Bags:frontal:sensor/control MODULE-INACTIVE
ODI opened this investigation based on reports of inadvertent airbag deployment.Data provided by Ford indicated that the airbag clockspring jumper wire, which is situated inside the steering wheel assembly, was installed in a manner that would allow it to rub (abrade) against a sharp metal edge on the nearby horn plate.Because the horn plate is electrically grounded the abrasion of an airbag wire on the sharp edge could cause a short circuit condition.As a result the airbag light may illuminate and/or the airbag may inadvertently deploy.Inadvertent deployments are most likely to occur during the airbag system's self-diagnostic test that initiates when the ignition switch is turned on.Ford modified the vehicle design in late January 2006 adding a protective tape over the sharp metal edge of the horn plate.Ford made additional design changes on MY 2007 vehicles to the horn plate, the clockspring jumper, and the connector layouts to further address this issue.ODI identified 318 deployment incidents with 121 alleged injury reports from subject vehicles.All but one of the incident and injury reports occurred in vehicles built before the January 2006 modification.In addition, there was one incident and alleged injury reported in the MY 2006 Mark LT vehicles that share the same design. In letters dated February 21 and April 11, 2011, Ford announced a recall of all of the approximately 1.3 million MY 2004-2006 F-150 vehicles built prior to January 24, 2006, the date the initial vehicle modification was made.In addition, approximately 14,000 MY 2006 Mark LT vehicles built prior to January 24, 2006 will also be recalled.Vehicles built after that date, which contain the modification, are not within the recall scope.Accordingly the investigation is closed.
PE08001 · Loss Of Brake POWER-ASSIST
Opened Jan 8, 2008 · Closed May 9, 2008
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:power Assist; Service Brakes, Hydraulic:power Assist:vacuum; Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Additional source detail variants (3)
Service Brakes, Hydraulic:power Assist
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Service Brakes, Hydraulic:power Assist:vacuum
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
BY LETTER DATED MAY 5, 2008, FORD MOTOR COMPANY (FORD) NOTIFIED THE AGENCY THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-208) TO ADDRESS A MANUFACTURING DEFECT IN APPROXIMATELY 605,684 MODEL YEAR (MY) 2005 AND 2006 FORD F-150 AND LINCOLN MARK LT VEHICLES ORIGINALLY EQUIPPED WITH THE 5.4L DISPLACEMENT, 3-VALVE PER CYLINDER, V-8 ENGINE.THE RECALLED VEHICLES WERE BUILT FROM JULY 18, 2004 THROUGH MAY 31, 2006 AT THE DEARBORN TRUCK PLANT; FROM MAY 4, 2004 THROUGH MAY 31, 2006 AT THE KANSAS CITY ASSEMBLY PLANT; AND FROM APRIL 19, 2004 THROUGH MAY 31, 2006 AT THE NORFOLK TRUCK PLANT.THE VEHICLES WERE MANUFACTURED WITH THE SAME DEFECTIVE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY UNIQUE TO THE 5.4L V-8 ENGINE.FORD F-150 VEHICLES EQUIPPED WITH OPTIONALLY AVAILABLE 4.2L V6 AND 4.6L V-8 ENGINES ARE NOT INCLUDED IN THIS RECALL ACTION BECAUSE THEY UTILIZE A DIFFERENT, ONE-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT DOES NOT EXHIBIT AN APPARENT DEFECT TREND. THE RECALLED VEHICLES UTILIZE A TWO-PIECE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY COMPRISED OF A STANDPIPE ASSEMBLY AND VACUUM HOSE.THE STANDPIPE ASSEMBLY ATTACHES TO A FITTING ON THE ENGINE AIR INTAKE MANIFOLD UTILIZING A FLEXIBLE RUBBER HOSE AND PLASTIC ELBOW.THE VACUUM HOSE ATTACHES TO THE OPPOSITE END OF THE STANDPIPE ASSEMBLY AND CONNECTS TO A CHECK VALVE FITTING AT THE BRAKE BOOSTER ASSEMBLY.ACCORDING TO FORD, THE PORTION OF THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY ATTACHED TO THE INTAKE MANIFOLD MAY SWELL OVER TIME AND LOSE RETENTION FORCE, WHICH MAY ALLOW THE HOSE TO BECOME DETACHED FROM THE INTAKE MANIFOLD.SHOULD THE BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY BE DISRUPTED, APPLICATION OF THE BRAKE PEDAL MAY DEPLETE THE VACUUM RESERVE AND CONSEQUENTLY RESULT IN LOSS OF BRAKE POWER-ASSIST. TO CORRECT THE SAFETY DEFECT, FORD WILL INSTALL AN IMPROVED DESIGN BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY THAT UTILIZES A HOSE CLAMP AT THE INTAKE MANIFOLD ATTACHMENT. THIS REMEDY WILL BE PROVIDED FREE OF CHARGE FOR ALL RECALLED VEHICLES.LATER PRODUCTION FORD F-150 AND LINCOLN MARK LT VEHICLES BUILT AFTER MAY 2006 WERE MANUFACTURED WITH A HOSE CLAMP AT THE BRAKE BOOSTER VACUUM SUPPLY HOSE/INTAKE MANIFOLD ATTACHMENT AND ARE NOT AFFECTED. TO DATE, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 324 NON-DUPLICATIVE COMPLAINTS AND 14 NON-INJURY CRASHES RELATED TO THE ALLEGED DEFECT IN THE SUBJECT VEHICLES.IN ADDITION, ODI IS AWARE OF 4,465 SUBJECT VEHICLES THAT EXPERIENCED ONE OR MORE WARRANTY CLAIMS TO REPAIR OR REPLACE THE SUBJECT BRAKE BOOSTER VACUUM SUPPLY HOSE ASSEMBLY. THE ACTION TAKEN BY FORD IS SUFFICIENT TO RESOLVE THE ISSUES RAISED BY THIS INVESTIGATION.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.