NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
1,316 reportsMileage unknown · Aug 6, 2015
Air BagsCrashInjury
I INVESTIGATED A TRAFFIC COLLISION INVOLVING A 2011 FORD ESCAPE THAT SUSTAINED SIGNIFICANT FRONT END DAMAGE DURING THE EVENT. THE AIRBAGS FAILED TO DEPLOY DURING THE COLLISION AFTER THE VEHICLE SUSTAINED DAMAGE TO THE ENTIRE FRONT BUMPER AREA TO INCLUDE THE BUCKLING OF THE HOOD AREA. I HAVE PHOTOGRAPHS OF THE VEHICLE DAMAGE I CA…
Read full complaint
I INVESTIGATED A TRAFFIC COLLISION INVOLVING A 2011 FORD ESCAPE THAT SUSTAINED SIGNIFICANT FRONT END DAMAGE DURING THE EVENT. THE AIRBAGS FAILED TO DEPLOY DURING THE COLLISION AFTER THE VEHICLE SUSTAINED DAMAGE TO THE ENTIRE FRONT BUMPER AREA TO INCLUDE THE BUCKLING OF THE HOOD AREA. I HAVE PHOTOGRAPHS OF THE VEHICLE DAMAGE I CAN E-MAIL SHOWING THE VEHICLE AND DAMAGE SUSTAINED. INJURIES WERE INCURRED FROM PARTIES IN BOTH VEHICLES (2 CAR COLLISION). PLEASE CONTACT ME AT THE MADERA POLICE DEPARTMENT FOR FURTHER INFORMATION REGARDING THIS INCIDENT AND MY CONCERN FOR THE AIRBAGS FAILING TO DEPLOY...UPDATED 10/15/15 *BF *CN
NHTSA ODI #10746877
119,453 miles · Aug 3, 2015
StructureUnknown Or OtherVisibility/wiper
SUN ROOF SHATTERED WHILE IN HOT SUN,LATER BLEW OUT ONTO THE HIGHWAY
NHTSA ODI #10745873
100,650 miles · Jul 30, 2015
Unknown Or Other
FIRST DATE OF OCCURRENCE: 7/22/15 I WAS DRIVING ABOUT 40 MPH AND IT SEEMED AS THOUGH EVEN THOUGH I HAD FUEL IN MY GAS TANK, THAT THE CAR WAS RUNNING OUT OF GAS. I PUT IT IN PARK, TURNED IT OFF AND TURNED IT BACK ON AGAIN AND IT RAN FINE. (VEHICLE BEGAN KIND OF SPUTTERING AND WHEN I PRESSED ON THE GAS PETAL, IT WAS LIKE IT DIDN…
Read full complaint
FIRST DATE OF OCCURRENCE: 7/22/15 I WAS DRIVING ABOUT 40 MPH AND IT SEEMED AS THOUGH EVEN THOUGH I HAD FUEL IN MY GAS TANK, THAT THE CAR WAS RUNNING OUT OF GAS. I PUT IT IN PARK, TURNED IT OFF AND TURNED IT BACK ON AGAIN AND IT RAN FINE. (VEHICLE BEGAN KIND OF SPUTTERING AND WHEN I PRESSED ON THE GAS PETAL, IT WAS LIKE IT DIDN'T WORK AT ALL.) WAS DRIVING A DISTANCE OF APPROXIMATELY 25 MILES WHEN THIS HAPPENED. SECOND DATE OF OCCURRENCE: 7/24/15 I WAS DRIVING ABOUT 50 MPH AND THE SAME ISSUE MENTIONED ABOVE HAPPENED. WHEN I TURNED THE VEHICLE BACK ON, IT TOOK IT A FEW SECONDS TO TURN BACK ON. THIRD DATE OF OCCURRENCE: 7/25/15 I WAS DRIVING ABOUT 50 MPH AND THE SAME ISSUE MENTIONED ABOVE HAPPENED. TOOK VEHICLE TO A SHOP ON 7/27/15 AND THEY SAID THEY COULD NOT FIND ANYTHING WRONG WITH IT. FOURTH DATE OF OCCURRENCE: 7/29/15 I WAS DRIVING ABOUT 40 MPH AND THE SAME ISSUE MENTIONED ABOVE HAPPENED. DROVE APPROXIMATELY 2 MILES WHEN THIS OCCURRED. FIFTH DATE OF OCCURRENCE: 7/30/15 I WAS DRIVING 40-50 MPH AND DROVE APPROXIMATELY 7 MILES WHEN THIS OCCURRED. HAD A DIAGNOSTICS MACHINE HOOKED UP TO VEHICLE AND IT READ ERROR CODE P2111 THROTTLE ACTUATOR STUCK OPEN.
NHTSA ODI #10744920
70,000 miles · Jul 27, 2015
Electrical SystemEngineUnknown Or Other
MY CAR WILL BE IDLING AND SUDDENLY POWER DOWN. RECENTLY WHILE I HAVE BEEN SLOWING DOWN AT A TRAFFIC LIGHT, STOP LIGHT, OR BRAKING FOR TRAFFIC IT WILL POWER DOWN. AFTER RESEARCHING ONLINE I HAVE FOUND THAT HUNDREDS OF OTHER FORD ESCAPE OWNERS HAVE HAD THE SAME ISSUE, SOME HAVE HAD IT HAPPEN WHILE DRIVING AT HIGH RATES OF SPEED. I…
Read full complaint
MY CAR WILL BE IDLING AND SUDDENLY POWER DOWN. RECENTLY WHILE I HAVE BEEN SLOWING DOWN AT A TRAFFIC LIGHT, STOP LIGHT, OR BRAKING FOR TRAFFIC IT WILL POWER DOWN. AFTER RESEARCHING ONLINE I HAVE FOUND THAT HUNDREDS OF OTHER FORD ESCAPE OWNERS HAVE HAD THE SAME ISSUE, SOME HAVE HAD IT HAPPEN WHILE DRIVING AT HIGH RATES OF SPEED. I HAVE TAKEN IT TO 4 DIFFERENT MECHANICS, 2 OF WHICH ARE FORD DEALERSHIPS AND THEY WORK ON IT CHARGE ME A LOT OF MONEY AND IT CONTINUES TO HAPPEN. ALMOST A YEAR NOW! I'M FED UP.
NHTSA ODI #10744044
20,000 miles · Jul 21, 2015
Electrical System
DRIVERS SIDE DOOR LATCH SWITCH SAYS IT IS NOT LATCHED, BUT IT IS. THIS CAUSES THE INTERIOR DOME LIGHTS TO REMAIN ON WHILE DRIVING. HARD TO DRIVE AT NIGHT WITH LIGHTS ON. DANGEROUS. DOORS DO NOT LOCK PROPERLY BECAUSE IT THINKS THE DOOR IS AJAR. I UNDERSTAND THOUSANDS OF COMPLAINTS ON THIS EXACT ISSUE.
NHTSA ODI #10735397
51,751 miles · Jul 16, 2015
Engine
TRAVELING HOME ON ROUTE 1 NORTH, MASSACHUSETTS IN TRAFFIC ABOUT 20MPH CAR BEGAN TO STALL AND SPUTTER AND WRENCH LIGHT CAME ON. BROUGHT CAR TO AUTO PARTS STORE FOR FREE DIAGNOSTIC IMMEDIATELY AND INSPECTION SHOWED "POWER TRAIN ISSUE" (ARE YOU KIDDING ME? JUST PURCHASED THIS USED CAR 3 MONTHS AGO!) NEXT DAY, SAME THING HAPPENED TW…
Read full complaint
TRAVELING HOME ON ROUTE 1 NORTH, MASSACHUSETTS IN TRAFFIC ABOUT 20MPH CAR BEGAN TO STALL AND SPUTTER AND WRENCH LIGHT CAME ON. BROUGHT CAR TO AUTO PARTS STORE FOR FREE DIAGNOSTIC IMMEDIATELY AND INSPECTION SHOWED "POWER TRAIN ISSUE" (ARE YOU KIDDING ME? JUST PURCHASED THIS USED CAR 3 MONTHS AGO!) NEXT DAY, SAME THING HAPPENED TWICE. CALLED THE DEALER WHO SOLD THE CAR TO ME CANNOT INSPECT THE CAR FOR TWO WEEKS. THIS IS UNACCEPTABLE. FORD ADMITS THERE IS AN ISSUE WITH THE ELECTRONIC THROTTLE BODY (ETB) BUT HAS NOT RECALLED THE VEHICLES.
NHTSA ODI #10734588
101,400 miles · Jul 9, 2015
EngineVehicle Speed Control
WAS DRIVING THROUGH TOWN, VEHICLE REVVED UP AND THEN STALLED. STOPPED VEHICLE, TURNED OFF, AND RESTARTED. STARTED UP WITHOUT AN ISSUE. 3 DAYS LATER, WHILE DRIVING TO WORK, VEHICLES WRENCH INDICATOR LIGHT CAME ON AND VEHICLE LOST POWER. RESTARTED OKAY. AS THE WEEK PROGRESSED, VEHICLE STARTED LOSING POWER SEVERAL TIMES DURING MY 2…
Read full complaint
WAS DRIVING THROUGH TOWN, VEHICLE REVVED UP AND THEN STALLED. STOPPED VEHICLE, TURNED OFF, AND RESTARTED. STARTED UP WITHOUT AN ISSUE. 3 DAYS LATER, WHILE DRIVING TO WORK, VEHICLES WRENCH INDICATOR LIGHT CAME ON AND VEHICLE LOST POWER. RESTARTED OKAY. AS THE WEEK PROGRESSED, VEHICLE STARTED LOSING POWER SEVERAL TIMES DURING MY 20 MILE TRIP TO WORK AND BACK, 40 MILES ROUND TRIP. THEN ON 7/7/15, VEHICLE LOST POWER 4 TIMES ON MY WAY HOME, THE SECOND TIME IT LOST POWER THE ENGINE INDICATOR LIGHT CAME ON AND STAYED ON. IT ALSO TOOK LONGER TO RESTART THE VEHICLE. CHECKED COMPUTER FOR CODE. CODE STATES P 2112, TAC SYSTEM STUCK SHUT. LOOKED UP THIS CODE AND INFO, AND IT SEEMS TO BE RELATED TO THE THROTTLE BODY. I FOUND SOMETHING THAT STATES THERE WAS A RECALL ON THIS PART, BUT I WAS NEVER NOTIFIED OF THIS. I WOULD LIKE TO GET THIS PROBLEM FIXED SO I CAN DRIVE MY VEHICLE. I'M NERVOUS ABOUT DRIVING IT AS I HAVE POOR SIGNAL ON MY CELL PHONE BETWEEN HOME AND WORK AND DONT WANT TO BE STRANDED. PLEASE HELP ME IN ANYWAY YOU CAN.
NHTSA ODI #10733069
50,000 miles · Jul 6, 2015
EngineVehicle Speed Control
AS I WAS DRIVING AT 50-55 MILES AN HOUR MY VEHICLE BUCKED AND LOST POWER AND WHEN ACCELERATING IT FEELS AS IF THE CAR IS GOING TO STALL. WHEN STARTING UP FROM A COMPLETE STOP THE CAR WILL HESITATE WHEN TRYING TO ACCELERATE AND BUCKS.
NHTSA ODI #10732150
71,240 miles · Jun 29, 2015
Electrical SystemEngineVehicle Speed Control
GOING SOUTH ON I81 TO WATERTOWN, NY. VEHICLE QUIT AND I COASTED TO THE SIDE OF THE HIGHWAY. TRACTOR-TRAILER BEHIND ME SWERVED TO MISS ME. ALMOST HIT A CAR COMING OFF THE EXIT RAMP, HAD NO POWER TO EXCELERATE TO GET BY HIM. COULD HAVE BEEN A WOPPER OF AN ACCIDENT.
NHTSA ODI #10730874
20,000 miles · Jun 26, 2015
Unknown Or Other
I WAS AT A TRAFFIC LIGHT AND TURNING LEFT TO MAKE THE TURN AND GO UP THE HILL. THE CAR LOST POWER AND I ACTUALLY THOUGHT IT HAD STALLED. THE CAR HAS DONE THIS FOR ME NUMEROUS TIMES AND I AM AFRAID IT WILL CAUSE AN ACCIDENT WHERE SOMEONE WILL HIT ME IN THE REAR WHEN MY CAR DOES NOT ACCELERATE
NHTSA ODI #10730625
Official recalls
2Oct 26, 2016
Ford Motor Company (Ford) is recalling certain model year 2010-2012 Ford Escape vehicles manufactured February 26, 2009, to April 29, 2012, and 2010-2011 Mercury Mariner vehicles manufactured February 25, 2009, to December 12, 2010. On vehicles with a 3.0L engine, the Fuel Delivery Module (FDM) may crack, causing a fuel leak.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source increases the risk of a fire.
Remedy: Ford will notify owners, and dealers will replace the FDM flange with one that has a redesigned fuel supply port, free of charge. Remedy parts are currently unavailable. Interim notices were mailed to owners on December 13, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S41.
May 29, 2014
Ford Motor Company (Ford) is recalling certain model year 2008-2011 Ford Escape and Mercury Mariner vehicles manufactured August 18, 2006, through September 11, 2010. The affected vehicles have a steering torque sensor that may not be able to properly detect driver steering input. As a result, the system could remove the Electric Power Steering (EPS) assist.
Consequence & remedy
Consequence: If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will update the software for the power steering control module (PSCM) and the instrument cluster module, free of charge. If a vehicle shows a history of a loss of the torque sensor signal or fault codes relating to the PSCM when the vehicle is brought in for the recall remedy, the affected components will be replaced, free of charge. The recall began on July 18, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S05.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4DP15001 · Loss Of Power Steering While Driving
Opened Apr 1, 2015 · Closed Jun 14, 2018
Status: closed (inferred from source dates) · Steering:electric Power Assist System
On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric power assisted steering (NHTSA 14V-284, Ford 14S05). Ford's DIR described the defect condition as a poor signal to noise ratio [SNR] in the torque sensor within the Electric Power Assisted Steering (EPAS) system [which] does not allow the PSCM to determine the driver's steering input. When the system detects this fault condition, it transitions the EPAS system to the fail-safe/manual steering mode.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Ford's remedy instructs dealers to check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTCs) to determine the proper repair procedure. If no DTCs are present, dealers are to update the PSCM and instrument cluster module software. The updated PSCM software changes the torque sensor fault strategy so that the SNR condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If DTCs indicating faults in the torque sensor, PSCM or Power Steering Motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (DTC B2278); or 2) replaces the steering column for faults related to the PSCM (DTC B1342) or motor (DTC B2277).Continued in attachment pages
PE13003 · Electronic Throttle Body Malfunction
Opened Feb 21, 2013 · Closed Feb 28, 2014
Status: closed (inferred from source dates) · Engine
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
DP12006 · Electronic Throttle Body Malfunction
Opened Oct 2, 2012 · Closed Feb 21, 2013
Status: closed (inferred from source dates) · Engine
In a letter dated August 30, 2012, The North Carolina Consumers Council (NCCC) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged electronic throttle body failures resulting in engine stall or surge while driving in model year (MY) 2005 through 2012 Ford Escape vehicles. On October 2, 2012 the Office of Defects Investigation (ODI) opened a Defect Petition DP12-006 to evaluate whether to grant or deny the petition. The petition is hereby granted on certain model years. The NCCC letter cites two complaints of stall while driving in MY 2009 Ford Escape vehicles that were diagnosed as failed throttle bodies with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed. The petitioner indicates that the owners of both vehicles reported experiencing repeated incidents of stalling and engine surging. According to Ford, Escape non-hybrid vehicles are equipped with Electronic Throttle Body (ETB) assemblies beginning with MY 2009. Vehicles manufactured between June 22, 2009 and October 15, 2009 may contain contaminated printed circuit boards (PCB) with plating variations. Plating variations could lead to a lack of continuity in the throttle position sensor circuit where P2111 and/or other DTCs would be generated and stored. Ford and its electronic throttle body supplier, Delphi, modified the PCB manufacturing process and issued a technical service bulletin (TSB) 09-23-5. Vehicles produced after October 15, 2009 incorporated ETBs manufactured with a PCB process that resolved this condition. ODI's analysis identified a total of 123 unique reports indicating allegations of reduced motive power or vehicle stall. Depending on the condition of throttle control system malfunction, a driver may experience varying levels of reduced engine performance associated with three limp home modes. In two limp modes, reduced engine performance may maintain vehicle speeds above 20mph while the third is a limited limp home mode with engine speeds limited to approximately 900 RPM. Allegations of stall appear to be related to the limited limp home mode. Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability. Allegations of vehicle surge appear to be related to limp home mode operation. Complaints alleging surge are most likely related to engine RPM fluctuations at low vehicle speeds or idle as the control system engages to prevent engine stall. In limited limp mode, rough-idle conditions may exist while the control system attempts to modulate engine RPMs once the vehicle reaches a reduced speed to maintain approximately 900 RPM. Separately, ODI received 59 complaints alleging incidents of engine stall while driving in model year (MY) 2010-2011 Ford Fusion vehicles. Approximately 60 percent (36) of the incidents occurred at speeds of 40 miles per hour or more. Eighty percent of complaints (47) were received beginning March 2012 and 14 complaints reported that the throttle body was replaced or DTCs associated with limp home modes. Additionally, Ford issued TSB 10-21-6 addressing DTCs associated with idle speed drops and limited limp home mode. The petition is granted on certain model years.Preliminary Evaluation PE13-003 has been opened to assess the scope, frequency and potential safety consequences associated with the alleged defect.See full copy of the closing resume for this defect petition for list of the VOQs associated with the defect petition analysis.
PE11016 · Rear Liftgate Window Glass Breakage
Opened Apr 27, 2011 · Closed Aug 18, 2011
Status: closed (inferred from source dates) · Structure:body:hatchback/liftgate; Structure:body:hatchback/liftgate:hinge And Attachments; Structure:body:hatchback/liftgate:support Device/strut; Visibility; Visibility:glass, Side/rear
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Additional source detail variants (5)
Structure:body:hatchback/liftgate
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure:body:hatchback/liftgate:hinge And Attachments
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure:body:hatchback/liftgate:support Device/strut
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Visibility
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Visibility:glass, Side/rear
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Illustration