NHTSA owner reports · September 18, 2026 snapshot.
Vehicle Speed Control complaints
245 reportsClear category filter20,650 miles · Jun 12, 2013
Fuel/propulsion SystemVehicle Speed Control
I WAS TRAVELING APPROXIMATELY 70 MPH ON THE INTERSTATE. MY CAR SHIFTED QUICKLY INTO A LOW GEAR AND THE WRENCH LIGHT CAME ON THE DASHBOARD INDICATING A POWERTRAIN FAILURE. I WAS ABLE TO MANEUVER OFF THE FREEWAY AND SHUT THE CAR DOWN. IT WOULD START UP AGAIN, AND WE LIMPED INTO THE FORD DEALERSHIP WHICH WAS ABOUT 1/4 MILE AWAY.…
Read full complaint
I WAS TRAVELING APPROXIMATELY 70 MPH ON THE INTERSTATE. MY CAR SHIFTED QUICKLY INTO A LOW GEAR AND THE WRENCH LIGHT CAME ON THE DASHBOARD INDICATING A POWERTRAIN FAILURE. I WAS ABLE TO MANEUVER OFF THE FREEWAY AND SHUT THE CAR DOWN. IT WOULD START UP AGAIN, AND WE LIMPED INTO THE FORD DEALERSHIP WHICH WAS ABOUT 1/4 MILE AWAY. THE DEALERSHIP REPLACED THE "THROTTLE BODY" AND INDICATED I WAS THE "THIRD ONE THIS WEEK". *TR
NHTSA ODI #10519499
49,000 miles · Jun 10, 2013
EngineFuel/propulsion SystemVehicle Speed Control
DRIVING THE CAR WE START TO EXCEL AND THE CAR SHUTS DOWN DUE TO THE THROTTLE BODY NOT FUNCTIONING RIGHT. *TR
NHTSA ODI #10515968
52,130 miles · Jun 9, 2013
Fuel/propulsion SystemVehicle Speed Control
WHILE DRIVING CAR STARTED TO SHIMMY, THEN WOULD NO LONGER ACCELERATE. TURNED OFF. RESTARTED AND WAS ABLE TO DRIVE HOME. ON THE WAY TO THE REPAIR SHOP ON JUNE 3, 2013, WHILE DRIVING THE CAR STARTED TO SHIMMY THEN WOULD NO LONGER ACCELERATE. TURNED OFF. RESTARTED AND WAS ABLE TO DRIVE TO THE REPAIR SHOP. *TR
NHTSA ODI #10515882
39,000 miles · Jun 7, 2013
Vehicle Speed Control
THIS VEHICLE IS DRIVEN BY MY SON WHILE HE IS AT COLLEGE. THE VEHICLE HAS HAD APPROXIMATELY 8 INSTANCES IN THE PAST 6-9 MONTHS (7 OF THOSE IN THE PAST MONTH DURING A ONE WEEK TIME PERIOD) IN WHICH THE VEHICLE HAS LOST A SIGNIFICANT AMOUNT OF POWER AND SPEED WHICH HAS REQUIRED HIM TO PULL OFF THE HIGHWAY FOR HIS SAFETY. ONCE OFF…
Read full complaint
THIS VEHICLE IS DRIVEN BY MY SON WHILE HE IS AT COLLEGE. THE VEHICLE HAS HAD APPROXIMATELY 8 INSTANCES IN THE PAST 6-9 MONTHS (7 OF THOSE IN THE PAST MONTH DURING A ONE WEEK TIME PERIOD) IN WHICH THE VEHICLE HAS LOST A SIGNIFICANT AMOUNT OF POWER AND SPEED WHICH HAS REQUIRED HIM TO PULL OFF THE HIGHWAY FOR HIS SAFETY. ONCE OFF THE HIGHWAY, HE TURNED THE VEHICLE OFF AND THEN TURNED THE VEHICLE BACK ON WHICH CLEARED THE PROBLEM. AT THE TIME OF THESE ISSUES, THE VEHICLE HAD APPROXIMATELY 38,000 MILES AND WAS 2 1/4 YEARS OLD. HE SUBSEQUENTLY TOOK THE VEHICLE IN FOR SERVICE, SEVERAL DAYS AFTER THE WEEK IN WHICH HE HAD 7 SEPARATE INCIDENTS, AND THE FORD DEALER REPLACED THE THROTTLE BODY. THERE APPEARS TO BE A SIGNIFICANT BODY OF KNOWLEDGE THAT INDICATES FORD HAS A PROBLEM WITH THE THROTTLE BODY ON LATE-MODEL ESCAPES. FORD SHOULD, AT A MINIMUM, ACKNOWLEDGE THIS SAFETY CONCERN, AND ALSO MAKE REPAIRS AT NO COST TO THE CONSUMER, TO MITIGATE THIS PROBLEM. *TR
NHTSA ODI #10515587
26,500 miles · Jun 6, 2013
Vehicle Speed Control
THE CAR CAME TO A SUDDEN STOP WITHOUT WARNING, IT SEEMS TO HAVE A FAULTY THROTTLE BODY. *TR
NHTSA ODI #10515531
40,000 miles · Jun 6, 2013
Electrical SystemEngineVehicle Speed Control
I WAS DRIVING UP A HILL WHEN MY ENGINE SHUT OFF AND CAR STARTED LURCHING FORWARD. THE BRAKES SLOWED THE CAR DOWN BUT LURCHING CONTINUED. THE CAR RESTARTED OKAY BUT STALLED SEVERAL MORE TIMES AS I WAS DRIVING IT TO THE DEALER. THERE WERE NO WARNING LIGHTS ON AND I HAVE ALWAYS TAKEN GREAT CARE OF THE CAR. THERE WERE NO ODD NOISES …
Read full complaint
I WAS DRIVING UP A HILL WHEN MY ENGINE SHUT OFF AND CAR STARTED LURCHING FORWARD. THE BRAKES SLOWED THE CAR DOWN BUT LURCHING CONTINUED. THE CAR RESTARTED OKAY BUT STALLED SEVERAL MORE TIMES AS I WAS DRIVING IT TO THE DEALER. THERE WERE NO WARNING LIGHTS ON AND I HAVE ALWAYS TAKEN GREAT CARE OF THE CAR. THERE WERE NO ODD NOISES OR SIGNS THAT SOMETHING WAS WRONG UNTIL THE CAR STOPPED. I AM THANKFUL THAT I WAS ON A NEIGHBORHOOD ROAD AND NOT A BUSY STREET OR HIGHWAY. DEALER SAYS THE ISSUE IS THE ELECTRONIC THROTTLE BODY WHICH IS ON NATIONAL BACKORDER AND MAY TAKE 6-8 WEEKS TO REPAIR. IF SOMETHING IS ON NATIONAL BACKORDER, DOES THAT MEAN THIS IS HAPPENING TO OTHERS AS WELL? PLEASE INVESTIGATE. *TR
NHTSA ODI #10515458
40,000 miles · Jun 6, 2013
Engine And Engine CoolingVehicle Speed Control
ENGINE STALLS UPON ACCELERATION, HAVE TO PULL OVER AND TURN THE ENGINE OFF AND THEN DO A RESTART. IT IS NOW AT THE DEALERSHIP WITH A DEFECTIVE THROTTLE BODY WAITING ON THE PART. I NOW UNDERSTAND IT IS BEING RE-DESIGNED WITH NO ETA ON MANUFACTURE OR DELIVERY TO MY DEALER. *TR
NHTSA ODI #10515457
37,500 miles · Jun 5, 2013
EngineFuel/propulsion SystemVehicle Speed Control
VEHICLE WAS ACCELERATED TO CROSS AN INTERSECTION AND ENGINE DECELLED TO AN IDLE CONDITION - THIS HAPPENED AT SPEED ALSO - VERY DANGEROUS LOSS OF POWER WITHOUT NOTICE - ALMOST CAUSED AN ACCIDENT. WAS VERY INTERMITTENT TO BEGIN WITH - DEALER ATTEMPTED TSHOOT AND REPAIR BUT NO CODES FOUND - NEXT DAY AFTER DEALER ATTEMPT PROBLEM HAP…
Read full complaint
VEHICLE WAS ACCELERATED TO CROSS AN INTERSECTION AND ENGINE DECELLED TO AN IDLE CONDITION - THIS HAPPENED AT SPEED ALSO - VERY DANGEROUS LOSS OF POWER WITHOUT NOTICE - ALMOST CAUSED AN ACCIDENT. WAS VERY INTERMITTENT TO BEGIN WITH - DEALER ATTEMPTED TSHOOT AND REPAIR BUT NO CODES FOUND - NEXT DAY AFTER DEALER ATTEMPT PROBLEM HAPPENED NUMEROUS TIMES AND THE DEALER DETERMINED A BAD THROTTLE BODY. *TR
NHTSA ODI #10515357
26,000 miles · Jun 4, 2013
Fuel System, GasolineVehicle Speed Control
ENGINE WILL START HEAD DOWN THE ROAD AND ALL THE SUDDEN WILL LOSE PICK UP ,PUSH ON THE GAS AND NOTHING HAPPENS THEN ALL THE SUDDEN IT WILL SPEED UP ,INCLUDING THIS ONE THAT I HAVE ESTIMATED THE DATE AND MILEAGE FORD REPLACED THE THROTTLE BODY UNDER WARRANTY.....THE SECOND TIME THIS HAPPENED WAS ON 02SEP12 MILEAGE WAS 39619 IT …
Read full complaint
ENGINE WILL START HEAD DOWN THE ROAD AND ALL THE SUDDEN WILL LOSE PICK UP ,PUSH ON THE GAS AND NOTHING HAPPENS THEN ALL THE SUDDEN IT WILL SPEED UP ,INCLUDING THIS ONE THAT I HAVE ESTIMATED THE DATE AND MILEAGE FORD REPLACED THE THROTTLE BODY UNDER WARRANTY.....THE SECOND TIME THIS HAPPENED WAS ON 02SEP12 MILEAGE WAS 39619 IT DID THE SAME THING BUT LEFT ME ON THE SIDE OF THE ROAD AND HAD TO BE TOWED(90$) TO REPAIR ,FORD FOUND THE THROTTLE BODY UNABLE TO MAINTAIN IDLE COST ME ALMOST 400$ TO REPAIR ,THAT LEADS US UP TO TODAY WHERE I WAS GOING DOWN THE HIGHWAY AT ABOUT 60 MILES AN HOUR AND ALL THE SUDDEN IT CUT OUT AND HAD TO COST OUT OF HEAVY TRAFFIC AFTER ABOUT 2-3 MIN THE TRUCK PICKED UP AND RAN FINE TILL I GOT HOME AND CALLED FORD AND ASKED THEM WHAT I NEED TO DO CAUSE ITS DOING THE SAME THING IT HAD THE PREVIOUS TIMES.WAS INSTRUCTED TO GET IT TO A SERVICE DEPT TO HAVE IT CHECKED,ON THE WAY TO FORD DURING HEAVY TRAFFIC THE CAR STALLED IN AN INTERSECTION AND THANKFULLY THE OTHER DRIVER WAS PAYING ATTENTION HE WAS ABLE TO STOP THEIR COULD HAVE DEF BEEN A FATAL INJURY IF NOT BUT AS I WAS TOLD BY FORD THAT I WOULD ALSO HAVE TO PAY FOR THIS THROTTLE BODY BECAUSE IT WAS OUT OF WARRANTY DUE TO MILEAGE 04JUN13 58053 MILES. *TR
NHTSA ODI #10515087
35,000 miles · Jun 4, 2013
Vehicle Speed Control
VEHICLE WOULD NO LONGER ACCELERATE AND HAD TO CRUISE INTO A PARKING LOT. VEHICLE WAS THEN TOWED TO DEALER. WAS TOLD IT WAS A THROTTLE ASSEMBLY PROBLEM. THE PART IS ON NATIONAL BACKORDER AND IT HAS BEEN THREE WEEKS WITH NO FIX. IF THE EVENT HAD HAPPENED WHILE PULLING INTO TRAFFIC, INSTEAD OF IN THE FLOW, IT WOULD HAVE BEEN MU…
Read full complaint
VEHICLE WOULD NO LONGER ACCELERATE AND HAD TO CRUISE INTO A PARKING LOT. VEHICLE WAS THEN TOWED TO DEALER. WAS TOLD IT WAS A THROTTLE ASSEMBLY PROBLEM. THE PART IS ON NATIONAL BACKORDER AND IT HAS BEEN THREE WEEKS WITH NO FIX. IF THE EVENT HAD HAPPENED WHILE PULLING INTO TRAFFIC, INSTEAD OF IN THE FLOW, IT WOULD HAVE BEEN MUCH WORSE. LOOKING ONLINE I SEE THIS IS AN EXTREMELY COMMON PROBLEM. *TR
NHTSA ODI #10514977
Official recalls
2Oct 26, 2016
Ford Motor Company (Ford) is recalling certain model year 2010-2012 Ford Escape vehicles manufactured February 26, 2009, to April 29, 2012, and 2010-2011 Mercury Mariner vehicles manufactured February 25, 2009, to December 12, 2010. On vehicles with a 3.0L engine, the Fuel Delivery Module (FDM) may crack, causing a fuel leak.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source increases the risk of a fire.
Remedy: Ford will notify owners, and dealers will replace the FDM flange with one that has a redesigned fuel supply port, free of charge. Remedy parts are currently unavailable. Interim notices were mailed to owners on December 13, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S41.
May 29, 2014
Ford Motor Company (Ford) is recalling certain model year 2008-2011 Ford Escape and Mercury Mariner vehicles manufactured August 18, 2006, through September 11, 2010. The affected vehicles have a steering torque sensor that may not be able to properly detect driver steering input. As a result, the system could remove the Electric Power Steering (EPS) assist.
Consequence & remedy
Consequence: If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will update the software for the power steering control module (PSCM) and the instrument cluster module, free of charge. If a vehicle shows a history of a loss of the torque sensor signal or fault codes relating to the PSCM when the vehicle is brought in for the recall remedy, the affected components will be replaced, free of charge. The recall began on July 18, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S05.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4DP15001 · Loss Of Power Steering While Driving
Opened Apr 1, 2015 · Closed Jun 14, 2018
Status: closed (inferred from source dates) · Steering:electric Power Assist System
On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric power assisted steering (NHTSA 14V-284, Ford 14S05). Ford's DIR described the defect condition as a poor signal to noise ratio [SNR] in the torque sensor within the Electric Power Assisted Steering (EPAS) system [which] does not allow the PSCM to determine the driver's steering input. When the system detects this fault condition, it transitions the EPAS system to the fail-safe/manual steering mode.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Ford's remedy instructs dealers to check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTCs) to determine the proper repair procedure. If no DTCs are present, dealers are to update the PSCM and instrument cluster module software. The updated PSCM software changes the torque sensor fault strategy so that the SNR condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If DTCs indicating faults in the torque sensor, PSCM or Power Steering Motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (DTC B2278); or 2) replaces the steering column for faults related to the PSCM (DTC B1342) or motor (DTC B2277).Continued in attachment pages
PE13003 · Electronic Throttle Body Malfunction
Opened Feb 21, 2013 · Closed Feb 28, 2014
Status: closed (inferred from source dates) · Engine
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
DP12006 · Electronic Throttle Body Malfunction
Opened Oct 2, 2012 · Closed Feb 21, 2013
Status: closed (inferred from source dates) · Engine
In a letter dated August 30, 2012, The North Carolina Consumers Council (NCCC) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged electronic throttle body failures resulting in engine stall or surge while driving in model year (MY) 2005 through 2012 Ford Escape vehicles. On October 2, 2012 the Office of Defects Investigation (ODI) opened a Defect Petition DP12-006 to evaluate whether to grant or deny the petition. The petition is hereby granted on certain model years. The NCCC letter cites two complaints of stall while driving in MY 2009 Ford Escape vehicles that were diagnosed as failed throttle bodies with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed. The petitioner indicates that the owners of both vehicles reported experiencing repeated incidents of stalling and engine surging. According to Ford, Escape non-hybrid vehicles are equipped with Electronic Throttle Body (ETB) assemblies beginning with MY 2009. Vehicles manufactured between June 22, 2009 and October 15, 2009 may contain contaminated printed circuit boards (PCB) with plating variations. Plating variations could lead to a lack of continuity in the throttle position sensor circuit where P2111 and/or other DTCs would be generated and stored. Ford and its electronic throttle body supplier, Delphi, modified the PCB manufacturing process and issued a technical service bulletin (TSB) 09-23-5. Vehicles produced after October 15, 2009 incorporated ETBs manufactured with a PCB process that resolved this condition. ODI's analysis identified a total of 123 unique reports indicating allegations of reduced motive power or vehicle stall. Depending on the condition of throttle control system malfunction, a driver may experience varying levels of reduced engine performance associated with three limp home modes. In two limp modes, reduced engine performance may maintain vehicle speeds above 20mph while the third is a limited limp home mode with engine speeds limited to approximately 900 RPM. Allegations of stall appear to be related to the limited limp home mode. Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability. Allegations of vehicle surge appear to be related to limp home mode operation. Complaints alleging surge are most likely related to engine RPM fluctuations at low vehicle speeds or idle as the control system engages to prevent engine stall. In limited limp mode, rough-idle conditions may exist while the control system attempts to modulate engine RPMs once the vehicle reaches a reduced speed to maintain approximately 900 RPM. Separately, ODI received 59 complaints alleging incidents of engine stall while driving in model year (MY) 2010-2011 Ford Fusion vehicles. Approximately 60 percent (36) of the incidents occurred at speeds of 40 miles per hour or more. Eighty percent of complaints (47) were received beginning March 2012 and 14 complaints reported that the throttle body was replaced or DTCs associated with limp home modes. Additionally, Ford issued TSB 10-21-6 addressing DTCs associated with idle speed drops and limited limp home mode. The petition is granted on certain model years.Preliminary Evaluation PE13-003 has been opened to assess the scope, frequency and potential safety consequences associated with the alleged defect.See full copy of the closing resume for this defect petition for list of the VOQs associated with the defect petition analysis.
PE11016 · Rear Liftgate Window Glass Breakage
Opened Apr 27, 2011 · Closed Aug 18, 2011
Status: closed (inferred from source dates) · Structure:body:hatchback/liftgate; Structure:body:hatchback/liftgate:hinge And Attachments; Structure:body:hatchback/liftgate:support Device/strut; Visibility; Visibility:glass, Side/rear
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Additional source detail variants (5)
Structure:body:hatchback/liftgate
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure:body:hatchback/liftgate:hinge And Attachments
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure:body:hatchback/liftgate:support Device/strut
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Visibility
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Visibility:glass, Side/rear
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Illustration