NHTSA owner reports · September 18, 2026 snapshot.
Steering complaints
409 reportsClear category filter112,000 miles · Feb 17, 2022
Steering
The contact owns a 2011 Ford Escape. The contact stated while driving at various speeds, the steering wheel became difficult to turn. The contact stated no warning light was illuminated. The vehicle was not taken to be diagnosed or repaired. The manufacturer was informed of the failure. The contact was awaiting a response. The f…
Read full complaint
The contact owns a 2011 Ford Escape. The contact stated while driving at various speeds, the steering wheel became difficult to turn. The contact stated no warning light was illuminated. The vehicle was not taken to be diagnosed or repaired. The manufacturer was informed of the failure. The contact was awaiting a response. The failure mileage was approximately 112,000. THE CONSUMER STATED THE TORQUE SENSOR FAILED AND WAS NOT COVERED BY THE RECALL 14S05, WHICH WAS EXPIRED.
NHTSA ODI #11452578
Mileage unknown · Feb 9, 2022
Steering
Hello I am contacting you about my 2011 Ford Escape. Approximately January 14, 2022 I was driving on the freeway when my steering started to feel slightly rigid. I got off the freeway and pulled into a parking lot Where I attempted to maneuver into a space when my power steering went completely out .It appeared to be manual stee…
Read full complaint
Hello I am contacting you about my 2011 Ford Escape. Approximately January 14, 2022 I was driving on the freeway when my steering started to feel slightly rigid. I got off the freeway and pulled into a parking lot Where I attempted to maneuver into a space when my power steering went completely out .It appeared to be manual steering only. I had to slam on my brakes to keep from hitting the vehicle next to the space I was trying to park in. There was no warning prior to this event. I contacted Ford who opened a case. I explained I had found on the Internet this had been recalled however my VIN number was not in the recalled numbers. The dealer told me they charged $140 an hour to diagnose plus if it was not covered that is additional .The Ford representative advised me to take it to the dealer to be inspected. The dealer confirmed there is a power steering failure and it DID need to be replaced however it was going to be at my cost as it was not covered under the recall. This amount is close to 800.00 The dealer has had my vehicle since January 21st almost 3 weeks now. They have not provided or offered a vehicle while I wait. They advise me they are waiting on parts and they would call me when they have completed the repairs after my second call for an update. I also have a recall I was contacted about which they are going to take care of at the same time. The case number Ford assigned me is as follows CAS34964338 I am very fortunate I was able to get off of the freeway before losing complete steering ability. My vehicle is at Germain Ford in Beavercreek Ohio. Safety Recall 14S05 for my exact circumstances doesn't include my VIN # but includes exact problem in the recall. My vehicle was made at the Kansas plant. Mr Michael Berardi from Ford wrote an article which I found on internet which instructs dealers to fix the defect free of charge even if they didn't receive a recall letter 800-325-5621. They refused to speak with me and said they only talk with dealers.
NHTSA ODI #11451157
Mileage unknown · Feb 7, 2022
Steering
In the last month, the car has gone into manual steering mode by itself. It looses power steering. The risk of accident is significantly higher when this happens. The car has not been inspected by a dealer yet. I have an appointment on Thursday, Feb 10, 2022. The is a open recall, 14S05, however, when I spoke to the dealer they…
Read full complaint
In the last month, the car has gone into manual steering mode by itself. It looses power steering. The risk of accident is significantly higher when this happens. The car has not been inspected by a dealer yet. I have an appointment on Thursday, Feb 10, 2022. The is a open recall, 14S05, however, when I spoke to the dealer they were not aware of it. I also called Ford Customer Service and the rep there didn't know about it either. My car 2011 Ford Escape was built at the Kansas City Plant. There is no warning when this happens.
NHTSA ODI #11450800
182,479 miles · Feb 7, 2022
Steering
The contact owns a 2011 Ford Escape. The contact stated that while driving at an undisclosed speed, the power steering assist failed and the steering wheel locked up. The contact restarted the vehicle to correct the failure. The dealer was made aware of the failure; however, the vehicle was not diagnosed nor repaired. The manufa…
Read full complaint
The contact owns a 2011 Ford Escape. The contact stated that while driving at an undisclosed speed, the power steering assist failed and the steering wheel locked up. The contact restarted the vehicle to correct the failure. The dealer was made aware of the failure; however, the vehicle was not diagnosed nor repaired. The manufacturer was made aware of the failure and referred the contact to file a complaint with the NHTSA. The failure mileage was 182,479.
NHTSA ODI #11450799
Mileage unknown · Feb 4, 2022
Steering
2011 Ford Escape XLT power steering column assembly internal failure. Power steering lost. The steering wheel locks up while the car is in motion causing no control of the vehicle. Same as the ones recalled. My VIN number falls short TWO days after the Ford recall window #14S05. NHTSA Recall # 14V284000
NHTSA ODI #11450429
111,982 miles · Feb 4, 2022
Steering
The contact's son owns a 2011 Ford Escape. The contact stated after the vehicle was serviced for front brakes at an independent mechanic; while driving 35 MPH, the steering wheel became difficult to turn. The contact stated that the traction control warning light was illuminated. The contact parked on the side of the road and re…
Read full complaint
The contact's son owns a 2011 Ford Escape. The contact stated after the vehicle was serviced for front brakes at an independent mechanic; while driving 35 MPH, the steering wheel became difficult to turn. The contact stated that the traction control warning light was illuminated. The contact parked on the side of the road and restarted the vehicle. The contact stated she depressed the traction control button and was able to regain control of the steering wheel. The contact took the vehicle to an independent mechanic and associated the failure with NHTSA Campaign Number: 14V284000 (Steering) however, the VIN was not included. The contact called the local dealer and made them aware of the failure. The vehicle was not repaired but was pending repairs. The manufacturer had been informed of the failure. The failure mileage was 111,982.
NHTSA ODI #11450352
93,000 miles · Feb 3, 2022
Steering
The contact owns a 2011 Ford Escape. The contact stated while driving on three separate occasions, the steering wheel locked up without warning. The vehicle was taken to the local dealer where it was diagnosed that the power steering control module needed to be replaced. The contact was provided an estimate however, the vehicle…
Read full complaint
The contact owns a 2011 Ford Escape. The contact stated while driving on three separate occasions, the steering wheel locked up without warning. The vehicle was taken to the local dealer where it was diagnosed that the power steering control module needed to be replaced. The contact was provided an estimate however, the vehicle was not repaired. The contact stated the failure was related to NHTSA Campaign Number 14V284000 (Steering). The manufacturer was notified however, no further assistance was provided. The failure mileage was approximately 93,000.
NHTSA ODI #11450138
160,000 miles · Jan 25, 2022
Steering
The contact owns a 2011 Ford Escape. The contact stated while starting the vehicle, the power steering assist fault warning light was illuminated, and the steering wheel became difficult to turn. The contact was able to drive to her residence at slow speeds. The vehicle was not diagnosed or repaired. A dealer was not contacted. …
Read full complaint
The contact owns a 2011 Ford Escape. The contact stated while starting the vehicle, the power steering assist fault warning light was illuminated, and the steering wheel became difficult to turn. The contact was able to drive to her residence at slow speeds. The vehicle was not diagnosed or repaired. A dealer was not contacted. Upon investigation, the contact associated the failure with NHTSA Campaign Number: 14V284000 (Steering) however, the VIN was not included. The manufacturer had not been informed of the failure. The failure mileage was approximately 160,000.
NHTSA ODI #11448777
Mileage unknown · Jan 24, 2022
Steering
From what I have read online, the power steering system on these cars has been recalled due to it randomly cutting off and accident risk growing. Ford Recall #14S05. My car is experiencing all of the same issues but it falls 5 months outside of the window of the recall. Mine was manufactured feburary 2011 and the cut off is Sept…
Read full complaint
From what I have read online, the power steering system on these cars has been recalled due to it randomly cutting off and accident risk growing. Ford Recall #14S05. My car is experiencing all of the same issues but it falls 5 months outside of the window of the recall. Mine was manufactured feburary 2011 and the cut off is September 2010. Is there anything I can due about this?
NHTSA ODI #11448711
Mileage unknown · Jan 19, 2022
Steering
The contact owns a 2011 Ford Escape. The contact stated that while making a right turn at 10 MPH, the power steering failed with two unknown warning lights illuminated. The contact had to use excessive force to complete the turn. The contact stated that the failure initially began intermittently; however, the failure had become …
Read full complaint
The contact owns a 2011 Ford Escape. The contact stated that while making a right turn at 10 MPH, the power steering failed with two unknown warning lights illuminated. The contact had to use excessive force to complete the turn. The contact stated that the failure initially began intermittently; however, the failure had become more frequent over the years. The contact had taken the vehicle to a dealer where he was informed that his vehicle was not included in NHTSA Campaign Number: 14V284000 (Steering). The manufacturer was also notified of the failure and referred him to NHTSA for assistance. The vehicle had yet to be repaired. The failure mileage was unknown.
NHTSA ODI #11448017
Official recalls
2Oct 26, 2016
Ford Motor Company (Ford) is recalling certain model year 2010-2012 Ford Escape vehicles manufactured February 26, 2009, to April 29, 2012, and 2010-2011 Mercury Mariner vehicles manufactured February 25, 2009, to December 12, 2010. On vehicles with a 3.0L engine, the Fuel Delivery Module (FDM) may crack, causing a fuel leak.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source increases the risk of a fire.
Remedy: Ford will notify owners, and dealers will replace the FDM flange with one that has a redesigned fuel supply port, free of charge. Remedy parts are currently unavailable. Interim notices were mailed to owners on December 13, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S41.
May 29, 2014
Ford Motor Company (Ford) is recalling certain model year 2008-2011 Ford Escape and Mercury Mariner vehicles manufactured August 18, 2006, through September 11, 2010. The affected vehicles have a steering torque sensor that may not be able to properly detect driver steering input. As a result, the system could remove the Electric Power Steering (EPS) assist.
Consequence & remedy
Consequence: If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will update the software for the power steering control module (PSCM) and the instrument cluster module, free of charge. If a vehicle shows a history of a loss of the torque sensor signal or fault codes relating to the PSCM when the vehicle is brought in for the recall remedy, the affected components will be replaced, free of charge. The recall began on July 18, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S05.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4DP15001 · Loss Of Power Steering While Driving
Opened Apr 1, 2015 · Closed Jun 14, 2018
Status: closed (inferred from source dates) · Steering:electric Power Assist System
On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric power assisted steering (NHTSA 14V-284, Ford 14S05). Ford's DIR described the defect condition as a poor signal to noise ratio [SNR] in the torque sensor within the Electric Power Assisted Steering (EPAS) system [which] does not allow the PSCM to determine the driver's steering input. When the system detects this fault condition, it transitions the EPAS system to the fail-safe/manual steering mode.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Ford's remedy instructs dealers to check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTCs) to determine the proper repair procedure. If no DTCs are present, dealers are to update the PSCM and instrument cluster module software. The updated PSCM software changes the torque sensor fault strategy so that the SNR condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If DTCs indicating faults in the torque sensor, PSCM or Power Steering Motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (DTC B2278); or 2) replaces the steering column for faults related to the PSCM (DTC B1342) or motor (DTC B2277).Continued in attachment pages
PE13003 · Electronic Throttle Body Malfunction
Opened Feb 21, 2013 · Closed Feb 28, 2014
Status: closed (inferred from source dates) · Engine
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
DP12006 · Electronic Throttle Body Malfunction
Opened Oct 2, 2012 · Closed Feb 21, 2013
Status: closed (inferred from source dates) · Engine
In a letter dated August 30, 2012, The North Carolina Consumers Council (NCCC) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged electronic throttle body failures resulting in engine stall or surge while driving in model year (MY) 2005 through 2012 Ford Escape vehicles. On October 2, 2012 the Office of Defects Investigation (ODI) opened a Defect Petition DP12-006 to evaluate whether to grant or deny the petition. The petition is hereby granted on certain model years. The NCCC letter cites two complaints of stall while driving in MY 2009 Ford Escape vehicles that were diagnosed as failed throttle bodies with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed. The petitioner indicates that the owners of both vehicles reported experiencing repeated incidents of stalling and engine surging. According to Ford, Escape non-hybrid vehicles are equipped with Electronic Throttle Body (ETB) assemblies beginning with MY 2009. Vehicles manufactured between June 22, 2009 and October 15, 2009 may contain contaminated printed circuit boards (PCB) with plating variations. Plating variations could lead to a lack of continuity in the throttle position sensor circuit where P2111 and/or other DTCs would be generated and stored. Ford and its electronic throttle body supplier, Delphi, modified the PCB manufacturing process and issued a technical service bulletin (TSB) 09-23-5. Vehicles produced after October 15, 2009 incorporated ETBs manufactured with a PCB process that resolved this condition. ODI's analysis identified a total of 123 unique reports indicating allegations of reduced motive power or vehicle stall. Depending on the condition of throttle control system malfunction, a driver may experience varying levels of reduced engine performance associated with three limp home modes. In two limp modes, reduced engine performance may maintain vehicle speeds above 20mph while the third is a limited limp home mode with engine speeds limited to approximately 900 RPM. Allegations of stall appear to be related to the limited limp home mode. Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability. Allegations of vehicle surge appear to be related to limp home mode operation. Complaints alleging surge are most likely related to engine RPM fluctuations at low vehicle speeds or idle as the control system engages to prevent engine stall. In limited limp mode, rough-idle conditions may exist while the control system attempts to modulate engine RPMs once the vehicle reaches a reduced speed to maintain approximately 900 RPM. Separately, ODI received 59 complaints alleging incidents of engine stall while driving in model year (MY) 2010-2011 Ford Fusion vehicles. Approximately 60 percent (36) of the incidents occurred at speeds of 40 miles per hour or more. Eighty percent of complaints (47) were received beginning March 2012 and 14 complaints reported that the throttle body was replaced or DTCs associated with limp home modes. Additionally, Ford issued TSB 10-21-6 addressing DTCs associated with idle speed drops and limited limp home mode. The petition is granted on certain model years.Preliminary Evaluation PE13-003 has been opened to assess the scope, frequency and potential safety consequences associated with the alleged defect.See full copy of the closing resume for this defect petition for list of the VOQs associated with the defect petition analysis.
PE11016 · Rear Liftgate Window Glass Breakage
Opened Apr 27, 2011 · Closed Aug 18, 2011
Status: closed (inferred from source dates) · Structure:body:hatchback/liftgate; Structure:body:hatchback/liftgate:hinge And Attachments; Structure:body:hatchback/liftgate:support Device/strut; Visibility; Visibility:glass, Side/rear
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Additional source detail variants (5)
Structure:body:hatchback/liftgate
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure:body:hatchback/liftgate:hinge And Attachments
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure:body:hatchback/liftgate:support Device/strut
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Visibility
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Visibility:glass, Side/rear
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Illustration