The contact owns a 2009 Ford Escape. The contact stated that upon his wife starting the vehicle, the "Power Steering Assist Fault" message was displayed on the instrument panel and the steering wheel failed to operate as needed. The contact was called to the scene of the failure and inspected the vehicle. The contact discovered …
Read full complaint
The contact owns a 2009 Ford Escape. The contact stated that upon his wife starting the vehicle, the "Power Steering Assist Fault" message was displayed on the instrument panel and the steering wheel failed to operate as needed. The contact was called to the scene of the failure and inspected the vehicle. The contact discovered that there was no mechanical failure with the vehicle. Due to the failure, the vehicle was towed to a dealer where it was diagnosed with a defective steering column. Upon investigation, the contact discovered NHTSA Campaign Number: 14V284000 (Steering). The contact notified the manufacturer of the failure and was informed that the VIN was not included in the recall. The contact was then referred to the NHTSA Hotline to report the failure. The vehicle was not repaired. The failure mileage was 77,000.
NHTSA ODI #11629191
223,000 miles · Nov 18, 2024
Steering
The contact owns a 2009 Ford Escape. The contact stated while starting the vehicle, the steering wheel seized with the check engine warning light illuminated. The contact stated that the steering wheel was stiff while attempting to start the vehicle. The vehicle was taken to the dealer where it was diagnosed and determined that…
Read full complaint
The contact owns a 2009 Ford Escape. The contact stated while starting the vehicle, the steering wheel seized with the check engine warning light illuminated. The contact stated that the steering wheel was stiff while attempting to start the vehicle. The vehicle was taken to the dealer where it was diagnosed and determined that the vehicle had lost power steering functionality and needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 223,000.
NHTSA ODI #11625969
249,000 miles · Nov 18, 2024
Steering
The contact owns a 2009 Ford Escape. The contact stated that while driving approximately 10 MPH, the steering wheel was seized, and the "Power Steering Assist Fault" message was displayed. The check engine and air bag warning lights were also illuminated. The vehicle was driven to an independent mechanic to be diagnosed. The con…
Read full complaint
The contact owns a 2009 Ford Escape. The contact stated that while driving approximately 10 MPH, the steering wheel was seized, and the "Power Steering Assist Fault" message was displayed. The check engine and air bag warning lights were also illuminated. The vehicle was driven to an independent mechanic to be diagnosed. The contact was made aware of DTC code: B-1936 and NHTSA Campaign Number: 14V284000 (Steering). The vehicle was repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 249,000.
NHTSA ODI #11625894
62,000 miles · Oct 29, 2024
Steering
The contact owns a 2009 Ford Escape. The contact stated that while his son was operating the vehicle, the power steering malfunctioned, and the steering wheel became difficult to turn in either direction. The cause of the failure was not yet determined. The manufacturer and local dealer were notified of the failure, but no assis…
Read full complaint
The contact owns a 2009 Ford Escape. The contact stated that while his son was operating the vehicle, the power steering malfunctioned, and the steering wheel became difficult to turn in either direction. The cause of the failure was not yet determined. The manufacturer and local dealer were notified of the failure, but no assistance was offered. The contact was informed that the VIN was not included in NHTSA Campaign Number: 14V284000 (STEERING). The contact stated that the vehicle had experienced the failure listed in the recall. The failure mileage was 62,000.
NHTSA ODI #11622504
120,000 miles · Oct 15, 2024
Steering
The contact owns a 2009 Ford Escape. The contact stated that while driving at an undisclosed speed, the steering wheel seized with no warning light illuminated. The contact stated that the steering wheel became difficult to turn. The vehicle was taken to an independent mechanic where it was diagnosed that the power steering fai…
Read full complaint
The contact owns a 2009 Ford Escape. The contact stated that while driving at an undisclosed speed, the steering wheel seized with no warning light illuminated. The contact stated that the steering wheel became difficult to turn. The vehicle was taken to an independent mechanic where it was diagnosed that the power steering failed and needed to be replaced. The vehicle was not repaired. The dealer was contacted. The manufacturer was made aware of the issue and referred the contact to the NHSTA Hotline for assistance. The approximate failure mileage was 120,000.
NHTSA ODI #11619902
Mileage unknown · Oct 14, 2024
Steering
Yesterday, [XXX], the power steering first temporarily went out on a curve and came back on and I was able to continue driving with power steering. After I stopped the vehicle for roughly 1.5 hours (planned stop), it no longer worked. I was a short distance from home and returned home and parked the vehicle. I was not going a…
Read full complaint
Yesterday, [XXX], the power steering first temporarily went out on a curve and came back on and I was able to continue driving with power steering. After I stopped the vehicle for roughly 1.5 hours (planned stop), it no longer worked. I was a short distance from home and returned home and parked the vehicle. I was not going a high rate of speed when the temporary loss occurred; however, there is a great accident risk for this issue, especially in a heavy traffic and/or higher speed area. I started it twice today to see if it worked and it is not working. The system message says “power steering assist fault” on the dash. This was displaying yesterday and is also today. My vehicle was manufactured in Kansas City, MO and I am requesting the VIN be reviewed and included as part of the recall, 14S05A. Please assist as soon as possible so this can be resolved. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ODI #11619639
Mileage unknown · Oct 2, 2024
Steering
no powersteering went out while driving they reprogramed steering module nowit went out totally its bs on fords part
NHTSA ODI #11617758
Mileage unknown · Aug 24, 2024
SteeringUnknown Or Other
I was driving down the road then all the sudden halfway through making a turn the power steering went completely out almost causing me to wreck. I looked up the issue and it is on the recall list but for some reason this individual vehicle doesn't have the recall. It falls into all there peramiters for being recalled. The Ford d…
Read full complaint
I was driving down the road then all the sudden halfway through making a turn the power steering went completely out almost causing me to wreck. I looked up the issue and it is on the recall list but for some reason this individual vehicle doesn't have the recall. It falls into all there peramiters for being recalled. The Ford dealership gave me the same runaround. So now it is sitting with the power steering still not working. There were absolutely no warnings that this was going to happen. Not a light or anything.
NHTSA ODI #11610630
Mileage unknown · Aug 8, 2024
Steering
The contact owns a 2009 Ford Escape. The contact stated while driving at an undisclosed speed, the contact became aware that the electronic power steering was not functioning properly, requiring increased effort to maneuver the vehicle. The vehicle returned to normal functionality, but the failure became a regular occurrence. No…
Read full complaint
The contact owns a 2009 Ford Escape. The contact stated while driving at an undisclosed speed, the contact became aware that the electronic power steering was not functioning properly, requiring increased effort to maneuver the vehicle. The vehicle returned to normal functionality, but the failure became a regular occurrence. No warning lights were illuminated. The vehicle was taken to an independent mechanic, who diagnosed a failure with the electronic power steering control module. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 14V284000 (Steering); but the VIN was not included. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was unknown.
NHTSA ODI #11607324
Mileage unknown · May 28, 2024
Steering
Complete power steering assist loss with no warning. should have been fixed by dealer before we purchased the vehicle used with less the 4,000 miles on it. reference recall 14S05. While driving at 45 mph to turn onto the highway experienced complete power steering assist loss.
Ford Motor Company (Ford) is recalling certain model year 2008-2011 Ford Escape and Mercury Mariner vehicles manufactured August 18, 2006, through September 11, 2010. The affected vehicles have a steering torque sensor that may not be able to properly detect driver steering input. As a result, the system could remove the Electric Power Steering (EPS) assist.
Consequence & remedy
Consequence: If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will update the software for the power steering control module (PSCM) and the instrument cluster module, free of charge. If a vehicle shows a history of a loss of the torque sensor signal or fault codes relating to the PSCM when the vehicle is brought in for the recall remedy, the affected components will be replaced, free of charge. The recall began on July 18, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S05.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3
DP15001 · Loss Of Power Steering While Driving
Opened Apr 1, 2015 · Closed Jun 14, 2018
Status: closed (inferred from source dates) · Steering:electric Power Assist System
On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric power assisted steering (NHTSA 14V-284, Ford 14S05). Ford's DIR described the defect condition as a poor signal to noise ratio [SNR] in the torque sensor within the Electric Power Assisted Steering (EPAS) system [which] does not allow the PSCM to determine the driver's steering input. When the system detects this fault condition, it transitions the EPAS system to the fail-safe/manual steering mode.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Ford's remedy instructs dealers to check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTCs) to determine the proper repair procedure. If no DTCs are present, dealers are to update the PSCM and instrument cluster module software. The updated PSCM software changes the torque sensor fault strategy so that the SNR condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If DTCs indicating faults in the torque sensor, PSCM or Power Steering Motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (DTC B2278); or 2) replaces the steering column for faults related to the PSCM (DTC B1342) or motor (DTC B2277).Continued in attachment pages
PE13003 · Electronic Throttle Body Malfunction
Opened Feb 21, 2013 · Closed Feb 28, 2014
Status: closed (inferred from source dates) · Engine
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
DP12006 · Electronic Throttle Body Malfunction
Opened Oct 2, 2012 · Closed Feb 21, 2013
Status: closed (inferred from source dates) · Engine
In a letter dated August 30, 2012, The North Carolina Consumers Council (NCCC) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged electronic throttle body failures resulting in engine stall or surge while driving in model year (MY) 2005 through 2012 Ford Escape vehicles. On October 2, 2012 the Office of Defects Investigation (ODI) opened a Defect Petition DP12-006 to evaluate whether to grant or deny the petition. The petition is hereby granted on certain model years. The NCCC letter cites two complaints of stall while driving in MY 2009 Ford Escape vehicles that were diagnosed as failed throttle bodies with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed. The petitioner indicates that the owners of both vehicles reported experiencing repeated incidents of stalling and engine surging. According to Ford, Escape non-hybrid vehicles are equipped with Electronic Throttle Body (ETB) assemblies beginning with MY 2009. Vehicles manufactured between June 22, 2009 and October 15, 2009 may contain contaminated printed circuit boards (PCB) with plating variations. Plating variations could lead to a lack of continuity in the throttle position sensor circuit where P2111 and/or other DTCs would be generated and stored. Ford and its electronic throttle body supplier, Delphi, modified the PCB manufacturing process and issued a technical service bulletin (TSB) 09-23-5. Vehicles produced after October 15, 2009 incorporated ETBs manufactured with a PCB process that resolved this condition. ODI's analysis identified a total of 123 unique reports indicating allegations of reduced motive power or vehicle stall. Depending on the condition of throttle control system malfunction, a driver may experience varying levels of reduced engine performance associated with three limp home modes. In two limp modes, reduced engine performance may maintain vehicle speeds above 20mph while the third is a limited limp home mode with engine speeds limited to approximately 900 RPM. Allegations of stall appear to be related to the limited limp home mode. Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability. Allegations of vehicle surge appear to be related to limp home mode operation. Complaints alleging surge are most likely related to engine RPM fluctuations at low vehicle speeds or idle as the control system engages to prevent engine stall. In limited limp mode, rough-idle conditions may exist while the control system attempts to modulate engine RPMs once the vehicle reaches a reduced speed to maintain approximately 900 RPM. Separately, ODI received 59 complaints alleging incidents of engine stall while driving in model year (MY) 2010-2011 Ford Fusion vehicles. Approximately 60 percent (36) of the incidents occurred at speeds of 40 miles per hour or more. Eighty percent of complaints (47) were received beginning March 2012 and 14 complaints reported that the throttle body was replaced or DTCs associated with limp home modes. Additionally, Ford issued TSB 10-21-6 addressing DTCs associated with idle speed drops and limited limp home mode. The petition is granted on certain model years.Preliminary Evaluation PE13-003 has been opened to assess the scope, frequency and potential safety consequences associated with the alleged defect.See full copy of the closing resume for this defect petition for list of the VOQs associated with the defect petition analysis.
Illustration