NHTSA owner reports · September 18, 2026 snapshot.
Service Brakes, Hydraulic complaints
12 reportsClear category filter160,000 miles · Oct 23, 2024
Service Brakes, Hydraulic
The contact owns a 2009 Ford Escape. The contact stated while driving 45-55 MPH and depressing the brake pedal, the brake pedal traveled down to the floorboard and the vehicle failed to respond. The contact depressed the brake pedal harder, and the vehicle came to a complete stop. The contact drove to the residence, where the AB…
Read full complaint
The contact owns a 2009 Ford Escape. The contact stated while driving 45-55 MPH and depressing the brake pedal, the brake pedal traveled down to the floorboard and the vehicle failed to respond. The contact depressed the brake pedal harder, and the vehicle came to a complete stop. The contact drove to the residence, where the ABS warning light was illuminated. The vehicle was taken to an independent mechanic, who referred the contact to the dealer for assistance. The vehicle was taken to the dealer, where it was diagnosed that the ABS module had failed and needed to be replaced; however, the part was on backorder. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 160,000. The VIN was not available.
NHTSA ODI #11621600
130,000 miles · Feb 13, 2023
Service Brakes, Hydraulic
The contact owns a 2009 Ford Escape. The contact stated while driving at various speeds, the brake pedal was depressed but the vehicle was slow to respond. The contact stated that the brake pedal depressed to the floorboard. There were no warning lights illuminated. The local dealer was not contacted. The vehicle was not diagnos…
Read full complaint
The contact owns a 2009 Ford Escape. The contact stated while driving at various speeds, the brake pedal was depressed but the vehicle was slow to respond. The contact stated that the brake pedal depressed to the floorboard. There were no warning lights illuminated. The local dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was contacted and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 130,000.
NHTSA ODI #11506956
Mileage unknown · Jul 29, 2022
Service Brakes, Hydraulic
The contact owns a 2009 Ford Escape. The contact stated while driving at an undisclosed speed, a burning odor was detected with the check engine warning light illuminated. The contact pulled over and had the vehicle towed to the dealer, where it was diagnosed with ABS module failure. The dealer informed the contact that the ABS …
Read full complaint
The contact owns a 2009 Ford Escape. The contact stated while driving at an undisclosed speed, a burning odor was detected with the check engine warning light illuminated. The contact pulled over and had the vehicle towed to the dealer, where it was diagnosed with ABS module failure. The dealer informed the contact that the ABS module needed to be replaced; however, parts were on backorder. The vehicle was not repaired. The manufacturer was made aware of the failure and advised the contact to file a complaint with the NHTSA. The failure mileage was unknown.
NHTSA ODI #11476511
112,000 miles · Dec 16, 2021
Service Brakes, Hydraulic
The contact owns a 2009 Ford Escape. The contact stated while driving 50 MPH, the brake pedal was depressed to the floor before the vehicle started to slow down. The contact veered to the side of the road and waited for a few minutes to restart the vehicle; however, the failure persisted. There was no warning light illuminated. …
Read full complaint
The contact owns a 2009 Ford Escape. The contact stated while driving 50 MPH, the brake pedal was depressed to the floor before the vehicle started to slow down. The contact veered to the side of the road and waited for a few minutes to restart the vehicle; however, the failure persisted. There was no warning light illuminated. The contact drove the vehicle to the local dealer to be diagnosed. The contact was informed that the ABS system was corroded and needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 112,000.
NHTSA ODI #11444034
Mileage unknown · Dec 13, 2021
Service Brakes, Hydraulic
See NHTSA Recall No. 19V-904 for additional details. This recall should be amended to include the Ford Escape model line. The valve on the Anti-lock Braking System Module sticks open and causes reduced braking ability. The module is the same component as in the vehicles noted in the above referenced NHTSA recall.
NHTSA ODI #11443637
49,900 miles · Dec 9, 2021
Service Brakes, Hydraulic
The contact owns a 2009 Ford Escape. The contact stated that while her husband was driving at an undisclosed speed, the brake pedal went to the floorboard while depressed. The vehicle was taken to an independent mechanic and initially diagnosed with brake master cylinder failure. The brake master cylinder was replaced; however, …
Read full complaint
The contact owns a 2009 Ford Escape. The contact stated that while her husband was driving at an undisclosed speed, the brake pedal went to the floorboard while depressed. The vehicle was taken to an independent mechanic and initially diagnosed with brake master cylinder failure. The brake master cylinder was replaced; however, the failure recurred. The mechanic then diagnosed the vehicle with Anti-Lock Brake System (ABS) and hydraulic failure. The Antilock Brake System (ABS) and hydraulic needed to be replaced however, parts were not available. The vehicle was not repaired and remained with the independent mechanic. The manufacturer was made aware of the failure and informed the contact to take the vehicle to a dealer. The contact related the failure to NHTSA Campaign Number: 16V733000 (Service Brakes, Hydraulic, Electronic Stability Control) however, neither the VIN nor the type of vehicle was included in the recall. The failure mileage was 49,900.
NHTSA ODI #11443265
200,000 miles · Oct 4, 2021
Service Brakes, Hydraulic
The contact owns a 2009 Ford Escape. The contact stated that while depressing the brake pedal to stop the vehicle, the pedal extended to the floor and the vehicle did not immediately stop. The vehicle was taken to an independent mechanic who replaced the brake master cylinder however, the failure recurred. The local dealer was n…
Read full complaint
The contact owns a 2009 Ford Escape. The contact stated that while depressing the brake pedal to stop the vehicle, the pedal extended to the floor and the vehicle did not immediately stop. The vehicle was taken to an independent mechanic who replaced the brake master cylinder however, the failure recurred. The local dealer was notified of the failure and the contact was informed that the failure was due to a faulty ABS module however, the part was on backorder. The vehicle was not repaired. The manufacturer was not yet contacted. The failure mileage was 200,000.
NHTSA ODI #11435358
180,000 miles · Sep 28, 2021
Service Brakes, Hydraulic
The contact owns a 2009 Ford Escape. The contact stated that while driving at 35-45 MPH, the brake pedal would go to the floorboard when depressed. The failure occurred intermittently. The vehicle was taken to an independent mechanic and diagnosed with hydraulic brake control failure. The mechanic informed the contact that it wa…
Read full complaint
The contact owns a 2009 Ford Escape. The contact stated that while driving at 35-45 MPH, the brake pedal would go to the floorboard when depressed. The failure occurred intermittently. The vehicle was taken to an independent mechanic and diagnosed with hydraulic brake control failure. The mechanic informed the contact that it was a recurring issue. The vehicle was not repaired. The manufacturer was made aware of the failure but informed the contact that there was no recall associated with the VIN. The failure mileage was approximately 180,000. The VIN was unavailable.
NHTSA ODI #11434748
90,000 miles · Sep 3, 2021
Service Brakes, Hydraulic
The contact owns a 2009 Ford Escape. The contact stated while driving at various speeds, the brake pedal would depress the floorboard without warning. The contact had taken the vehicle to an independent mechanic who performed various brake tests and found no faults with the braking system. Neither the dealer nor the manufacturer…
Read full complaint
The contact owns a 2009 Ford Escape. The contact stated while driving at various speeds, the brake pedal would depress the floorboard without warning. The contact had taken the vehicle to an independent mechanic who performed various brake tests and found no faults with the braking system. Neither the dealer nor the manufacturer was notified of the failure. The vehicle was not repaired. The failure mileage was approximately 90,000.
NHTSA ODI #11431666
Mileage unknown · Feb 10, 2014
Power TrainService Brakes, Hydraulic
2009 FORD ESCAPE. CONSUMER WRITES IN REGARDS TO TRANSMISSION PROBLEMS. *SMD THE CONSUMER STATED WHEN HE TOOK THE VEHICLE TO THE DEALER, FOR A REGULARLY SCHEDULED OIL CHANGE, HE WAS SHOCKED TO HEAR HE NEEDED BRAKE PADS AND ROTORS. A WEEK LATER, THE VEHICLE HAD TO BE TOWED TO THE REPAIR, TO HAVE THE TRANSMISSION REPLACED AT A C…
Read full complaint
2009 FORD ESCAPE. CONSUMER WRITES IN REGARDS TO TRANSMISSION PROBLEMS. *SMD THE CONSUMER STATED WHEN HE TOOK THE VEHICLE TO THE DEALER, FOR A REGULARLY SCHEDULED OIL CHANGE, HE WAS SHOCKED TO HEAR HE NEEDED BRAKE PADS AND ROTORS. A WEEK LATER, THE VEHICLE HAD TO BE TOWED TO THE REPAIR, TO HAVE THE TRANSMISSION REPLACED AT A COST OF $3,400.
NHTSA ODI #10564082
NHTSA investigations
3DP15001 · Loss Of Power Steering While Driving
Opened Apr 1, 2015 · Closed Jun 14, 2018
Status: closed (inferred from source dates) · Steering:electric Power Assist System
On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric power assisted steering (NHTSA 14V-284, Ford 14S05). Ford's DIR described the defect condition as a poor signal to noise ratio [SNR] in the torque sensor within the Electric Power Assisted Steering (EPAS) system [which] does not allow the PSCM to determine the driver's steering input. When the system detects this fault condition, it transitions the EPAS system to the fail-safe/manual steering mode.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Ford's remedy instructs dealers to check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTCs) to determine the proper repair procedure. If no DTCs are present, dealers are to update the PSCM and instrument cluster module software. The updated PSCM software changes the torque sensor fault strategy so that the SNR condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If DTCs indicating faults in the torque sensor, PSCM or Power Steering Motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (DTC B2278); or 2) replaces the steering column for faults related to the PSCM (DTC B1342) or motor (DTC B2277).Continued in attachment pages
PE13003 · Electronic Throttle Body Malfunction
Opened Feb 21, 2013 · Closed Feb 28, 2014
Status: closed (inferred from source dates) · Engine
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
DP12006 · Electronic Throttle Body Malfunction
Opened Oct 2, 2012 · Closed Feb 21, 2013
Status: closed (inferred from source dates) · Engine
In a letter dated August 30, 2012, The North Carolina Consumers Council (NCCC) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged electronic throttle body failures resulting in engine stall or surge while driving in model year (MY) 2005 through 2012 Ford Escape vehicles. On October 2, 2012 the Office of Defects Investigation (ODI) opened a Defect Petition DP12-006 to evaluate whether to grant or deny the petition. The petition is hereby granted on certain model years. The NCCC letter cites two complaints of stall while driving in MY 2009 Ford Escape vehicles that were diagnosed as failed throttle bodies with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed. The petitioner indicates that the owners of both vehicles reported experiencing repeated incidents of stalling and engine surging. According to Ford, Escape non-hybrid vehicles are equipped with Electronic Throttle Body (ETB) assemblies beginning with MY 2009. Vehicles manufactured between June 22, 2009 and October 15, 2009 may contain contaminated printed circuit boards (PCB) with plating variations. Plating variations could lead to a lack of continuity in the throttle position sensor circuit where P2111 and/or other DTCs would be generated and stored. Ford and its electronic throttle body supplier, Delphi, modified the PCB manufacturing process and issued a technical service bulletin (TSB) 09-23-5. Vehicles produced after October 15, 2009 incorporated ETBs manufactured with a PCB process that resolved this condition. ODI's analysis identified a total of 123 unique reports indicating allegations of reduced motive power or vehicle stall. Depending on the condition of throttle control system malfunction, a driver may experience varying levels of reduced engine performance associated with three limp home modes. In two limp modes, reduced engine performance may maintain vehicle speeds above 20mph while the third is a limited limp home mode with engine speeds limited to approximately 900 RPM. Allegations of stall appear to be related to the limited limp home mode. Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability. Allegations of vehicle surge appear to be related to limp home mode operation. Complaints alleging surge are most likely related to engine RPM fluctuations at low vehicle speeds or idle as the control system engages to prevent engine stall. In limited limp mode, rough-idle conditions may exist while the control system attempts to modulate engine RPMs once the vehicle reaches a reduced speed to maintain approximately 900 RPM. Separately, ODI received 59 complaints alleging incidents of engine stall while driving in model year (MY) 2010-2011 Ford Fusion vehicles. Approximately 60 percent (36) of the incidents occurred at speeds of 40 miles per hour or more. Eighty percent of complaints (47) were received beginning March 2012 and 14 complaints reported that the throttle body was replaced or DTCs associated with limp home modes. Additionally, Ford issued TSB 10-21-6 addressing DTCs associated with idle speed drops and limited limp home mode. The petition is granted on certain model years.Preliminary Evaluation PE13-003 has been opened to assess the scope, frequency and potential safety consequences associated with the alleged defect.See full copy of the closing resume for this defect petition for list of the VOQs associated with the defect petition analysis.
Illustration