Steering. Review the 1,127 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Power Train. Review the 329 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Vehicle Speed Control. Review the 175 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

59 crash reports6 fire reports36 injury reports

What owners actually said

1,974 reports

Mileage unknown · Mar 10, 2023

Engine

The contact owns a 2008 Ford Escape. The contact stated that the oil cap had loosened. The vehicle was taken to an independent mechanic, where the oil cap and the valve cover were replaced; however, the failure recurred. The manufacturer was made aware of the failure and referred the contact to file a complaint with the NHTSA Ho…

Read full complaint

NHTSA ODI #11511245

Mileage unknown · Mar 1, 2023

Steering

Power steering went out and the steering wheel is very hard to turn. Yes the vehicle is available for inspection upon request. While driving my steering wheel became hard to turn so I almost got into an accident. I have taken the car to a service dealer and they stated that the power steering column needed to be replaced codes t…

Read full complaint

NHTSA ODI #11509737

Mileage unknown · Feb 23, 2023

Steering

Read full complaint

While driving in a city at about 30mph, my power steering froze and I could not easily make a turn. As a result, I had to stop on the side of the road and inspect what went on. A 'wrench' and a warning control light came on stating 'power steering assist failure'. I was able to drive slowly to my mechanic, with a very limited steering, to diagnose the issue. The error code that appeared on the diagnostic interface was B2278 - Steering Shaft Torque Sensor Malfunction. I was very lucky to drive on a slow road because driving it on a freeway could have been disastrous, maybe fatal in a worst case for myself and others on a freeway. There were no prior signs to the failure. I loved driving the car because it was very reliable. I drive my kids to and from school in this car. I contacted the manufacturer and a few dealerships about this. It turns out that there was a safety recall for 2008 - 2011 Ford Escape and Mercury Mariner vehicles (14S05). However, my car, for some reason, was never on a recall list. My car's power steering torque sensor failure clearly satisfies the safety recall requirements. Is there a way that I could take this back to a FORD dealership and get it fixed under the safety recall? I am currently residing and driving this car in Poland.

NHTSA ODI #11508660

169,000 miles · Feb 21, 2023

Steering

Read full complaint

The contact's niece owns a 2008 Ford Escape. The contact stated that while stopped, the steering wheel started shaking. The vehicle was taken to the dealer to be diagnosed. The mechanic retrieved code: B2278 (Steering Shaft Torque Sensor Malfunction). The vehicle was repaired. The contact related the failure to TSB: (Power Steering). The manufacturer was made aware of the failure and referred the contact to file a complaint with the NHTSA Hotline. The failure mileage was approximately 169,000.

NHTSA ODI #11508284

189,000 miles · Feb 16, 2023

Steering

Read full complaint

The contact owns a 2008 Ford Escape. The contact stated that while her father was driving approximately 45 MPH, the vehicle lost power steering functionality. The contact stated no warning light was illuminated. The contact had driven the vehicle, with no power steering, to an independent mechanic who diagnosed the vehicle and determined that the Electric Power Steering (EPS) assist had failed and needed to be replaced. The vehicle had not been repaired. The manufacturer had been informed of the failure. The contact and the independent mechanic researched online and determined that the failure was related to NHTSA Campaign Number: 14V284000 (Steering). The failure mileage was approximately 189,000.

NHTSA ODI #11507702

Mileage unknown · Feb 15, 2023

Service BrakesCrash

Read full complaint

ABS, parking break light and regen breaks disabled. My breaks will go all the way to the floor and have crashed into a vehicle because out of nowhere I was not able to break like normal. Is not safe to drive. Was diagnosed with a bad hydraulic control until like thousands of other people with this car. Ford posted a service bulletin about this issue and recommended replacing the flex hoses before eventually replacing the HCU BUT WONT PAY FOR IT. IT IS FAULTY AND THEY SHOULD BE HELD RESPONSIBLE AND RECALL THIS HCU ISSUE INSTEAD OF JUST ACKNOWLEDGING THERE IS SOMETHING WRONG WITH THOUSDANDS OF THESE VEHICLES.

NHTSA ODI #11507439

Mileage unknown · Feb 5, 2023

Steering

Read full complaint

On Tuesday a light came on that said “power steering assist fault” but it was still driving fine. Then the next morning when I was pull out of the parking spot I could barely turn the wheel. It was super hard to turn. I could hardly get back into the parking spot, it was super hard just to steer it back to the parking spot. If I would’ve been driving it would have definitely caused an accident. I had the car towed to a dealership, I was told that it was probably the power sterling pump but there is a recall on this car for that and my car (vin number) is not listed. But it’s the same problem. Maybe my vin number was miase? Please help.

NHTSA ODI #11505661

118,000 miles · Feb 3, 2023

Steering

Read full complaint

The contact owns a 2008 Ford Escape. The contact stated that while driving at an undisclosed speed, the vehicle experienced a loss of power steering assist with the power steering assist fault message displayed. The vehicle was taken to the dealer; however, the vehicle was not diagnosed or repaired. The dealer informed the contact that there was no recall associated with the VIN. The manufacturer was not made aware of the failure. The failure mileage was approximately 118,000.

NHTSA ODI #11505459

Mileage unknown · Feb 3, 2023

Steering

STEERING WHEEL TURNS AUTOMATICLLY TO THE RIGHT WHEN STARING VEHICLE. I TOOK THE VEHICLE TO HORNE FORD OF NOGALES THEY FOLLOWED SERVICE PROCEDURE AS PER WORKSHOP MANUAL FOUND AND DETERMINED ELECTRIC STEERING COLUMN (FAILED) THEY RECOMMENDED REPAIRS: ELECTRIC STEERING COLUMN ASSEMBLY. I HAVE A REPAIR ESTIMATE A COST OF 2,827.00

NHTSA ODI #11505418

207,000 miles · Jan 30, 2023

Steering

The contact's husband owns a 2008 Ford Escape. The contact stated that while starting the vehicle, the vehicle lost motive power and the power steering assist warning light illuminated. The vehicle was not diagnosed nor repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure and referred the…

Read full complaint

NHTSA ODI #11504415

Official recalls

15V606000 · Power Train:automatic Transmission:gear Position Indication (prndl); Power Train:automatic Transmission:lever And Linkage:floor Shift

Sep 29, 2015

Ford Motor Company (Ford) is recalling certain model year 2001-2008 Ford Escape and Mercury Mariner vehicles manufactured March 31, 2001, to September 1, 2009. The affected vehicles are equipped with either a 2.3L or 3.0L engine and have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.

Consequence & remedy

Consequence: If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "PARK" position, but the vehicle transmission may not actually be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.

Remedy: Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.

Additional source detail variants (2)

Power Train:automatic Transmission:lever And Linkage:floor Shift

Consequence: If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "PARK" position, but the vehicle transmission may not actually be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.

Remedy: Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.

Power Train:automatic Transmission:gear Position Indication (prndl)

14V526000 · Hybrid Propulsion System

Sep 3, 2014

Ford Motor Company (Ford) is recalling certain model year 2005-2008 Ford Escape hybrid electric vehicles manufactured October 13, 2003, to June 20, 2008, and 2006-2008 Mercury Mariner hybrid electric vehicles manufactured June 10, 2005, to June 20, 2008. The coolant pump for the hybrid system may fail resulting in the hybrid electronics overheating.

Consequence & remedy

Consequence: If the hybrid electronics system overheats, it may shut down the powertrain, resulting in a stall-like condition, increasing the risk of a crash.

Remedy: Ford will notify owners, and dealers will inspect and replace the original Motor Electronics Coolant (MEC) Pump with an improved brushless pump, free of charge. The recall is expected to begin on October 27, 2014. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 14S19.

14V284000 · Steering:electric Power Assist System

May 29, 2014

Ford Motor Company (Ford) is recalling certain model year 2008-2011 Ford Escape and Mercury Mariner vehicles manufactured August 18, 2006, through September 11, 2010. The affected vehicles have a steering torque sensor that may not be able to properly detect driver steering input. As a result, the system could remove the Electric Power Steering (EPS) assist.

Consequence & remedy

Consequence: If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash.

Remedy: Ford will notify owners, and dealers will update the software for the power steering control module (PSCM) and the instrument cluster module, free of charge. If a vehicle shows a history of a loss of the torque sensor signal or fault codes relating to the PSCM when the vehicle is brought in for the recall remedy, the affected components will be replaced, free of charge. The recall began on July 18, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S05.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

DP15001 · Loss Of Power Steering While Driving

Opened Apr 1, 2015 · Closed Jun 14, 2018

Status: closed (inferred from source dates) · Steering:electric Power Assist System

On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric power assisted steering (NHTSA 14V-284, Ford 14S05). Ford's DIR described the defect condition as a poor signal to noise ratio [SNR] in the torque sensor within the Electric Power Assisted Steering (EPAS) system [which] does not allow the PSCM to determine the driver's steering input. When the system detects this fault condition, it transitions the EPAS system to the fail-safe/manual steering mode.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Ford's remedy instructs dealers to check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTCs) to determine the proper repair procedure. If no DTCs are present, dealers are to update the PSCM and instrument cluster module software. The updated PSCM software changes the torque sensor fault strategy so that the SNR condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If DTCs indicating faults in the torque sensor, PSCM or Power Steering Motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (DTC B2278); or 2) replaces the steering column for faults related to the PSCM (DTC B1342) or motor (DTC B2277).Continued in attachment pages

DP12006 · Electronic Throttle Body Malfunction

Opened Oct 2, 2012 · Closed Feb 21, 2013

Status: closed (inferred from source dates) · Engine

In a letter dated August 30, 2012, The North Carolina Consumers Council (NCCC) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged electronic throttle body failures resulting in engine stall or surge while driving in model year (MY) 2005 through 2012 Ford Escape vehicles. On October 2, 2012 the Office of Defects Investigation (ODI) opened a Defect Petition DP12-006 to evaluate whether to grant or deny the petition. The petition is hereby granted on certain model years. The NCCC letter cites two complaints of stall while driving in MY 2009 Ford Escape vehicles that were diagnosed as failed throttle bodies with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed. The petitioner indicates that the owners of both vehicles reported experiencing repeated incidents of stalling and engine surging. According to Ford, Escape non-hybrid vehicles are equipped with Electronic Throttle Body (ETB) assemblies beginning with MY 2009. Vehicles manufactured between June 22, 2009 and October 15, 2009 may contain contaminated printed circuit boards (PCB) with plating variations. Plating variations could lead to a lack of continuity in the throttle position sensor circuit where P2111 and/or other DTCs would be generated and stored. Ford and its electronic throttle body supplier, Delphi, modified the PCB manufacturing process and issued a technical service bulletin (TSB) 09-23-5. Vehicles produced after October 15, 2009 incorporated ETBs manufactured with a PCB process that resolved this condition. ODI's analysis identified a total of 123 unique reports indicating allegations of reduced motive power or vehicle stall. Depending on the condition of throttle control system malfunction, a driver may experience varying levels of reduced engine performance associated with three limp home modes. In two limp modes, reduced engine performance may maintain vehicle speeds above 20mph while the third is a limited limp home mode with engine speeds limited to approximately 900 RPM. Allegations of stall appear to be related to the limited limp home mode. Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability. Allegations of vehicle surge appear to be related to limp home mode operation. Complaints alleging surge are most likely related to engine RPM fluctuations at low vehicle speeds or idle as the control system engages to prevent engine stall. In limited limp mode, rough-idle conditions may exist while the control system attempts to modulate engine RPMs once the vehicle reaches a reduced speed to maintain approximately 900 RPM. Separately, ODI received 59 complaints alleging incidents of engine stall while driving in model year (MY) 2010-2011 Ford Fusion vehicles. Approximately 60 percent (36) of the incidents occurred at speeds of 40 miles per hour or more. Eighty percent of complaints (47) were received beginning March 2012 and 14 complaints reported that the throttle body was replaced or DTCs associated with limp home modes. Additionally, Ford issued TSB 10-21-6 addressing DTCs associated with idle speed drops and limited limp home mode. The petition is granted on certain model years.Preliminary Evaluation PE13-003 has been opened to assess the scope, frequency and potential safety consequences associated with the alleged defect.See full copy of the closing resume for this defect petition for list of the VOQs associated with the defect petition analysis.

PE08060 · Tire Valve Cracking

Opened Oct 14, 2008 · Closed Apr 9, 2009

Status: closed (inferred from source dates) · Tires:valve

ON OCTOBER 14, 2008, ODI OPENED PE08-060 TO INVESTIGATE ALLEGATIONS OF CRACKED AND LEAKING SNAP-IN TIRE VALVES IN MODEL YEAR (MY) 2007 VEHICLES MANUFACTURED BY FORD MOTOR COMPANY.THE VALVES WERE SUPPLIED TO FORD BY TOPSEAL AUTO-PARTS, A SUBSIDIARY OF THE SHANGHAI BAOLONG AUTOMOTIVE CORPORATION IN CHINA.VALVES MADE BY TOPSEAL FOR AFTERMARKET SALE WERE THE SUBJECT OF TWO RECENT SAFETY RECALLS BY TECH INTERNATIONAL (08T-018) AND DILL AIR CONTROLS (08T-028), THE LATTER OF WHICH WAS INVESTIGATED BY ODI IN PE08-036 AND EA08-022.THE DEFECT CONDITIONS ADDRESSED BY THE AFTERMARKET TIRE VALVE RECALLS BOTH INVOLVED INADEQUATE RESISTANCE TO OZONE CRACKING DUE TO ISSUES WITH THE SUPPLY OF ANTI-OZONANT CHEMICALS TO TOPSEAL FOR A PERIOD FROM JULY TO MID-NOVEMBER 2006.THE AFTERMARKET VALVES WERE COMPOUNDED WITH A BLEND OF EPDM AND NATURAL RUBBER, USING A RELATIVELY LOW PERCENTAGE OF EPDM (EPDM PROVIDES INHERENT RESISTANCE TO OZONE CRACKING).HENCE, THE NEED FOR ANTI-OZONANT CHEMICALS AND THE PROBLEMS WITH CRACKING WHEN THOSE CHEMICALS WERE MISSING OR OUT OF SPECIFICATION IN SOME LOTS OF VALVES.BOTH RECALL CAMPAIGNS INVOLVED INSPECTION PROGRAMS TO IDENTIFY AND REPLACE VALVES WITH VISIBLE SURFACE CRACKING.ALTHOUGH THE TOPSEAL VALVES SUPPLIED TO FORD ALSO APPEAR TO HAVE BEEN AFFECTED BY THE ANTI-OZONANT SUPPLY ISSUES IN MID TO LATE-2006, FORD INDICATED THAT ITS VALVES WERE MADE AT A DIFFERENT TOPSEAL PRODUCTION LINE AND WERE COMPOUNDED WITH A HIGHER PERCENTAGE OF EPDM RUBBER TO MEET MORE STRINGENT SPECIFICATIONS FROM FORD.ODI'S ANALYSIS OF COMPLAINT AND WARRANTY DATA PROVIDED BY FORD SHOWED THAT PROBLEMS WITH CRACKED TIRE VALVES WERE SIGNIFICANTLY HIGHER FOR MY 2007 VEHICLES PRODUCED FROM DECEMBER 2006 THROUGH MARCH 2007.FORD RESPONDED BY IMPLEMENTING CHANGES IN ITS MATERIAL SPECIFICATIONS FOR SNAP-IN RUBBER TIRE VALVES AND ALSO INCREASING THE QUALITY AND ACCEPTANCE STANDARDS FOR VALVES IMPORTED FOR USE IN ITS VEHICLES.WHILE THE COMPLAINT AND WARRANTY CLAIM RATES ARE ELEVATED FOR SUBJECT VEHICLES PRODUCED FROM DECEMBER 2006 THROUGH MARCH 2007, THE RATES OF LEAKING VALVES ARE WELL BELOW ONE PERCENT OF PRODUCTION FOR EACH OF THE PEAK MONTHS FOR ALL OF THE AFFECTED MODELS.A SUBSTANTIAL MAJORITY OF THE SUBJECT VEHICLES ARE EQUIPPED WITH TIRE PRESSURE MONITORING SYSTEMS (TPMS) WHICH WARN THE DRIVER WHEN ANY TIRE PRESSURES DROPS BELOW 25 PERCENT OF RECOMMENDED INFLATION PRESSURE. AS OUTLINED IN A LETTER TO ODI DATED APRIL 6, 2009, FORD HAS AGREED TO SEND LETTERS TO OWNERS OF CERTAIN MY 2007 AND 2008 FORD, LINCOLN AND MERCURY VEHICLES TO PROVIDE INFORMATION ABOUT THE CRACKING CONCERN. LETTERS WILL BE SENT TO OWNERS OF VEHICLES BUILT FROM NOVEMBER 2006 THROUGH MAY 2007.OWNERS CAN OPT FOR A FREE DEALER INSPECTION.VALVES EXHIBITING SURFACE CRACKS OR AIR LEAKAGE RELATED TO OZONE ATTACK WILL BE REPLACED BY FORD UNDER ITS NORMAL WARRANTY TERMS.FORD EXPECTS TO SEND THE LETTER BY APPROXIMATELY MID-MAY 2009. BASED ON THE USE OF TPMS IN THE MAJORITY OF SUBJECT VEHICLES AND THE RELATIVELY LOW RATES OF REPAIRS ASSOCIATED WITH LEAKING VALVES AND RESULTANT TIRE DAMAGE, ODI BELIEVES THAT THE ACTIONS FORD HAS AGREED TO TAKE WILL PROVIDE EFFECTIVE AND EXPEDITIOUS RESOLUTION FOR VEHICLES THAT WERE BUILT DURING THE PERIOD WHEN VALVES WITH INADEQUATE RESISTANCE TO OZONE CRACKING WERE MOST LIKELY TO HAVE BEEN USED IN VEHICLE PRODUCTION.FURTHER INVESTIGATION OF THIS MATTER WOULD NOT BE AN EFFICIENT ALLOCATION OF AGENCY RESOURCES.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST.THE AGENCY WILL CONTINUE TO

Go deeper into Ford Escape problems

Ford Escape transmission problems →Ford Escape electrical problems →