IllustrationWhile I was driving my car my power steering stopped working.I took it to my service garage and he did some kind of a rebate on it.But he also said he dosen"the no how long it will work.
2008 Ford Escape
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2008 Ford Escape do not stand out strongly from the model-year median of 996.
About this comparison →How this year compares
Owner complaints by model year
Compare all Escape years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1140–25K
18725–50K
21950–75K
32675–100K
577100–150K
291150K+
1,714 reports with mileage · 260 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 1,127 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 329 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Vehicle Speed Control. Review the 175 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
59 crash reports6 fire reports36 injury reports
What owners actually said
1,974 reportsThe contact owns a 2008 Ford Escape. The contact stated that while starting the vehicle, the "Power Steering Assist Fault" warning message was displayed. The steering wheel was difficult to maneuver. The vehicle was towed to an independent mechanic. The mechanic reset the computer code B2278 (Power Steering Shaft Torque Sensor) …
Read full complaint
The contact owns a 2008 Ford Escape. The contact stated that while starting the vehicle, the "Power Steering Assist Fault" warning message was displayed. The steering wheel was difficult to maneuver. The vehicle was towed to an independent mechanic. The mechanic reset the computer code B2278 (Power Steering Shaft Torque Sensor) and performed steering angle torque sensor calibration; however, the failure recurred. The vehicle was not repaired. The manufacturer was made aware of the failure and referred the contact to file a complaint with NHTSA. The contact related the failure to NHTSA Campaign Number: 14V284000 (Steering) however, the VIN was not included in the recall. The failure mileage was 124,510.
I have a 2008 Ford Escape. I was driving with my 7 year old and 4 year old and my power steering out, out of nowhere and went into manual steering. Without me being aware of that I went to turn and my car would not turn, I almost wrecked (because I could not turn the wheel) into the person at the stop light while my kids were in…
Read full complaint
I have a 2008 Ford Escape. I was driving with my 7 year old and 4 year old and my power steering out, out of nowhere and went into manual steering. Without me being aware of that I went to turn and my car would not turn, I almost wrecked (because I could not turn the wheel) into the person at the stop light while my kids were in the car. Thankfully I hit my breaks and did not but it was a very scary moment for myself and my kids. I had my car towed to my mechanic who then told me the torque sensor went out. He looked online and it said there was a recall on the exact problem I am having for the exact model I have. I called Ford and one person told me that the software was cleared. I talked to another guy from a different ford who then told me that my car doesn’t and has never had a recall done and it doesn’t qualify. So I am frustrated trying to get this recall done that I’m getting misinformation on from multiple different people at ford. I can not drive my car because the steering is a safety hazard one and two I am not strong enough to turn the wheel if I wanted to. I need to get my children to and from school and myself to and from work and can’t because of this problem. I don’t understand how one person can tell me I had a recall done and the other tell me I did not and can’t. I’m having a hard time believing that I don’t have a recall on this problem when I have the exact problem and my car is a 2008 escape and the recall they have is for a ford escape models 2008-2011 for the torque sensor and software. I am a single mother who doesn’t have the extra money to have this problem fixed especially when there is a recall on my exact problem but no one at ford is being kind enough to help and they are all giving me different information. At this point I don’t know what to do because they are leaving me confused and with no options. I just want this safety hazard fixed as soon as possible.
The rear passenger door will not catch to release unlock or lock latch. It's like the door is forced closed will not open.
Vehicle lost electric steering assistance system while driving causing a crash in a street curve. This system problem is now intermittent. The Ford dealer told there is nothing they can do if I don't pay for the repair. I think this is a secury issue and Ford is responsible for it.
The contact owns a 2008 Ford Escape. The contact stated while driving at an unknown speed, the brake pedal was depressed; however, the pedal went straight to the floor before stopping. The contact veered to the side of the road and waited for a few minutes before restarting the vehicle before driving back to the residence. There…
Read full complaint
The contact owns a 2008 Ford Escape. The contact stated while driving at an unknown speed, the brake pedal was depressed; however, the pedal went straight to the floor before stopping. The contact veered to the side of the road and waited for a few minutes before restarting the vehicle before driving back to the residence. There was no warning light illuminated. The vehicle was taken to an independent mechanic who inspected the vehicle but could not duplicate the failure. The mechanic suspected that the ABS brake booster and brake master cylinder had caused of the failure. The failure recurred a few months later. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 104,550. Consumer had the master cylinder replaced (2/25/22) on the advice of the mechanic who originally suspected it might be a master cylinder issue.
Power steering assist fault is being displayed on the screen. My vehicle is hard to turn when slowing down.
Electric power steering intermittently has a failure while driving. Vehicle gets very hard to steer.
The contact owns a 2008 Ford Escape. The contact stated that while reversing out of her driveway, the power steering assist failed without warning. The contact called an independent mechanic to her home who informed her that there had been a recall placed on similar vehicles for the power steering, which he linked to the failure…
Read full complaint
The contact owns a 2008 Ford Escape. The contact stated that while reversing out of her driveway, the power steering assist failed without warning. The contact called an independent mechanic to her home who informed her that there had been a recall placed on similar vehicles for the power steering, which he linked to the failure. The manufacturer was then notified of the failure and informed her that the vehicle was not included in NHTSA Campaign Number: 14V284000 (Steering). The manufacturer then referred the contact to NHTSA for assistance. The vehicle had yet to be repaired. The failure mileage was approximately 100,000.
The contact owns a 2008 Ford Escape. The contact stated that while driving at 35 mph, the power steering failed while the contact was making a left turn. The failure caused the contact to crash into a parked vehicle. The air bags were deployed upon impact. The contact sustained injuries to her neck, back, left hand, and ringing …
Read full complaint
The contact owns a 2008 Ford Escape. The contact stated that while driving at 35 mph, the power steering failed while the contact was making a left turn. The failure caused the contact to crash into a parked vehicle. The air bags were deployed upon impact. The contact sustained injuries to her neck, back, left hand, and ringing noises were heard in her ears. However, no medical attention was received. No police report was filed. The vehicle was towed to a tow yard and was not yet deemed totaled by the insurance company. Prior to the failure, the steering rack and pinion and lower steering coupler shaft were replaced by the dealer. The manufacturer was not made aware of the failure. The failure mileage was approximately 144,000.
Official recalls
315V606000 · Power Train:automatic Transmission:gear Position Indication (prndl); Power Train:automatic Transmission:lever And Linkage:floor Shift
Sep 29, 2015
Ford Motor Company (Ford) is recalling certain model year 2001-2008 Ford Escape and Mercury Mariner vehicles manufactured March 31, 2001, to September 1, 2009. The affected vehicles are equipped with either a 2.3L or 3.0L engine and have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.
Consequence & remedy
Consequence: If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "PARK" position, but the vehicle transmission may not actually be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.
Additional source detail variants (2)
Power Train:automatic Transmission:lever And Linkage:floor Shift
Ford Motor Company (Ford) is recalling certain model year 2001-2008 Ford Escape and Mercury Mariner vehicles manufactured March 31, 2001, to September 1, 2009. The affected vehicles are equipped with either a 2.3L or 3.0L engine and have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.
Consequence: If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "PARK" position, but the vehicle transmission may not actually be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.
Power Train:automatic Transmission:gear Position Indication (prndl)
Ford Motor Company (Ford) is recalling certain model year 2001-2008 Ford Escape and Mercury Mariner vehicles manufactured March 31, 2001, to September 1, 2009. The affected vehicles are equipped with either a 2.3L or 3.0L engine and have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.
Consequence: If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "PARK" position, but the vehicle transmission may not actually be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.
14V526000 · Hybrid Propulsion System
Sep 3, 2014
Ford Motor Company (Ford) is recalling certain model year 2005-2008 Ford Escape hybrid electric vehicles manufactured October 13, 2003, to June 20, 2008, and 2006-2008 Mercury Mariner hybrid electric vehicles manufactured June 10, 2005, to June 20, 2008. The coolant pump for the hybrid system may fail resulting in the hybrid electronics overheating.
Consequence & remedy
Consequence: If the hybrid electronics system overheats, it may shut down the powertrain, resulting in a stall-like condition, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will inspect and replace the original Motor Electronics Coolant (MEC) Pump with an improved brushless pump, free of charge. The recall is expected to begin on October 27, 2014. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 14S19.
14V284000 · Steering:electric Power Assist System
May 29, 2014
Ford Motor Company (Ford) is recalling certain model year 2008-2011 Ford Escape and Mercury Mariner vehicles manufactured August 18, 2006, through September 11, 2010. The affected vehicles have a steering torque sensor that may not be able to properly detect driver steering input. As a result, the system could remove the Electric Power Steering (EPS) assist.
Consequence & remedy
Consequence: If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will update the software for the power steering control module (PSCM) and the instrument cluster module, free of charge. If a vehicle shows a history of a loss of the torque sensor signal or fault codes relating to the PSCM when the vehicle is brought in for the recall remedy, the affected components will be replaced, free of charge. The recall began on July 18, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S05.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3DP15001 · Loss Of Power Steering While Driving
Opened Apr 1, 2015 · Closed Jun 14, 2018
Status: closed (inferred from source dates) · Steering:electric Power Assist System
On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric power assisted steering (NHTSA 14V-284, Ford 14S05). Ford's DIR described the defect condition as a poor signal to noise ratio [SNR] in the torque sensor within the Electric Power Assisted Steering (EPAS) system [which] does not allow the PSCM to determine the driver's steering input. When the system detects this fault condition, it transitions the EPAS system to the fail-safe/manual steering mode.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Ford's remedy instructs dealers to check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTCs) to determine the proper repair procedure. If no DTCs are present, dealers are to update the PSCM and instrument cluster module software. The updated PSCM software changes the torque sensor fault strategy so that the SNR condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If DTCs indicating faults in the torque sensor, PSCM or Power Steering Motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (DTC B2278); or 2) replaces the steering column for faults related to the PSCM (DTC B1342) or motor (DTC B2277).Continued in attachment pages
DP12006 · Electronic Throttle Body Malfunction
Opened Oct 2, 2012 · Closed Feb 21, 2013
Status: closed (inferred from source dates) · Engine
In a letter dated August 30, 2012, The North Carolina Consumers Council (NCCC) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged electronic throttle body failures resulting in engine stall or surge while driving in model year (MY) 2005 through 2012 Ford Escape vehicles. On October 2, 2012 the Office of Defects Investigation (ODI) opened a Defect Petition DP12-006 to evaluate whether to grant or deny the petition. The petition is hereby granted on certain model years. The NCCC letter cites two complaints of stall while driving in MY 2009 Ford Escape vehicles that were diagnosed as failed throttle bodies with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed. The petitioner indicates that the owners of both vehicles reported experiencing repeated incidents of stalling and engine surging. According to Ford, Escape non-hybrid vehicles are equipped with Electronic Throttle Body (ETB) assemblies beginning with MY 2009. Vehicles manufactured between June 22, 2009 and October 15, 2009 may contain contaminated printed circuit boards (PCB) with plating variations. Plating variations could lead to a lack of continuity in the throttle position sensor circuit where P2111 and/or other DTCs would be generated and stored. Ford and its electronic throttle body supplier, Delphi, modified the PCB manufacturing process and issued a technical service bulletin (TSB) 09-23-5. Vehicles produced after October 15, 2009 incorporated ETBs manufactured with a PCB process that resolved this condition. ODI's analysis identified a total of 123 unique reports indicating allegations of reduced motive power or vehicle stall. Depending on the condition of throttle control system malfunction, a driver may experience varying levels of reduced engine performance associated with three limp home modes. In two limp modes, reduced engine performance may maintain vehicle speeds above 20mph while the third is a limited limp home mode with engine speeds limited to approximately 900 RPM. Allegations of stall appear to be related to the limited limp home mode. Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability. Allegations of vehicle surge appear to be related to limp home mode operation. Complaints alleging surge are most likely related to engine RPM fluctuations at low vehicle speeds or idle as the control system engages to prevent engine stall. In limited limp mode, rough-idle conditions may exist while the control system attempts to modulate engine RPMs once the vehicle reaches a reduced speed to maintain approximately 900 RPM. Separately, ODI received 59 complaints alleging incidents of engine stall while driving in model year (MY) 2010-2011 Ford Fusion vehicles. Approximately 60 percent (36) of the incidents occurred at speeds of 40 miles per hour or more. Eighty percent of complaints (47) were received beginning March 2012 and 14 complaints reported that the throttle body was replaced or DTCs associated with limp home modes. Additionally, Ford issued TSB 10-21-6 addressing DTCs associated with idle speed drops and limited limp home mode. The petition is granted on certain model years.Preliminary Evaluation PE13-003 has been opened to assess the scope, frequency and potential safety consequences associated with the alleged defect.See full copy of the closing resume for this defect petition for list of the VOQs associated with the defect petition analysis.
PE08060 · Tire Valve Cracking
Opened Oct 14, 2008 · Closed Apr 9, 2009
Status: closed (inferred from source dates) · Tires:valve
ON OCTOBER 14, 2008, ODI OPENED PE08-060 TO INVESTIGATE ALLEGATIONS OF CRACKED AND LEAKING SNAP-IN TIRE VALVES IN MODEL YEAR (MY) 2007 VEHICLES MANUFACTURED BY FORD MOTOR COMPANY.THE VALVES WERE SUPPLIED TO FORD BY TOPSEAL AUTO-PARTS, A SUBSIDIARY OF THE SHANGHAI BAOLONG AUTOMOTIVE CORPORATION IN CHINA.VALVES MADE BY TOPSEAL FOR AFTERMARKET SALE WERE THE SUBJECT OF TWO RECENT SAFETY RECALLS BY TECH INTERNATIONAL (08T-018) AND DILL AIR CONTROLS (08T-028), THE LATTER OF WHICH WAS INVESTIGATED BY ODI IN PE08-036 AND EA08-022.THE DEFECT CONDITIONS ADDRESSED BY THE AFTERMARKET TIRE VALVE RECALLS BOTH INVOLVED INADEQUATE RESISTANCE TO OZONE CRACKING DUE TO ISSUES WITH THE SUPPLY OF ANTI-OZONANT CHEMICALS TO TOPSEAL FOR A PERIOD FROM JULY TO MID-NOVEMBER 2006.THE AFTERMARKET VALVES WERE COMPOUNDED WITH A BLEND OF EPDM AND NATURAL RUBBER, USING A RELATIVELY LOW PERCENTAGE OF EPDM (EPDM PROVIDES INHERENT RESISTANCE TO OZONE CRACKING).HENCE, THE NEED FOR ANTI-OZONANT CHEMICALS AND THE PROBLEMS WITH CRACKING WHEN THOSE CHEMICALS WERE MISSING OR OUT OF SPECIFICATION IN SOME LOTS OF VALVES.BOTH RECALL CAMPAIGNS INVOLVED INSPECTION PROGRAMS TO IDENTIFY AND REPLACE VALVES WITH VISIBLE SURFACE CRACKING.ALTHOUGH THE TOPSEAL VALVES SUPPLIED TO FORD ALSO APPEAR TO HAVE BEEN AFFECTED BY THE ANTI-OZONANT SUPPLY ISSUES IN MID TO LATE-2006, FORD INDICATED THAT ITS VALVES WERE MADE AT A DIFFERENT TOPSEAL PRODUCTION LINE AND WERE COMPOUNDED WITH A HIGHER PERCENTAGE OF EPDM RUBBER TO MEET MORE STRINGENT SPECIFICATIONS FROM FORD.ODI'S ANALYSIS OF COMPLAINT AND WARRANTY DATA PROVIDED BY FORD SHOWED THAT PROBLEMS WITH CRACKED TIRE VALVES WERE SIGNIFICANTLY HIGHER FOR MY 2007 VEHICLES PRODUCED FROM DECEMBER 2006 THROUGH MARCH 2007.FORD RESPONDED BY IMPLEMENTING CHANGES IN ITS MATERIAL SPECIFICATIONS FOR SNAP-IN RUBBER TIRE VALVES AND ALSO INCREASING THE QUALITY AND ACCEPTANCE STANDARDS FOR VALVES IMPORTED FOR USE IN ITS VEHICLES.WHILE THE COMPLAINT AND WARRANTY CLAIM RATES ARE ELEVATED FOR SUBJECT VEHICLES PRODUCED FROM DECEMBER 2006 THROUGH MARCH 2007, THE RATES OF LEAKING VALVES ARE WELL BELOW ONE PERCENT OF PRODUCTION FOR EACH OF THE PEAK MONTHS FOR ALL OF THE AFFECTED MODELS.A SUBSTANTIAL MAJORITY OF THE SUBJECT VEHICLES ARE EQUIPPED WITH TIRE PRESSURE MONITORING SYSTEMS (TPMS) WHICH WARN THE DRIVER WHEN ANY TIRE PRESSURES DROPS BELOW 25 PERCENT OF RECOMMENDED INFLATION PRESSURE. AS OUTLINED IN A LETTER TO ODI DATED APRIL 6, 2009, FORD HAS AGREED TO SEND LETTERS TO OWNERS OF CERTAIN MY 2007 AND 2008 FORD, LINCOLN AND MERCURY VEHICLES TO PROVIDE INFORMATION ABOUT THE CRACKING CONCERN. LETTERS WILL BE SENT TO OWNERS OF VEHICLES BUILT FROM NOVEMBER 2006 THROUGH MAY 2007.OWNERS CAN OPT FOR A FREE DEALER INSPECTION.VALVES EXHIBITING SURFACE CRACKS OR AIR LEAKAGE RELATED TO OZONE ATTACK WILL BE REPLACED BY FORD UNDER ITS NORMAL WARRANTY TERMS.FORD EXPECTS TO SEND THE LETTER BY APPROXIMATELY MID-MAY 2009. BASED ON THE USE OF TPMS IN THE MAJORITY OF SUBJECT VEHICLES AND THE RELATIVELY LOW RATES OF REPAIRS ASSOCIATED WITH LEAKING VALVES AND RESULTANT TIRE DAMAGE, ODI BELIEVES THAT THE ACTIONS FORD HAS AGREED TO TAKE WILL PROVIDE EFFECTIVE AND EXPEDITIOUS RESOLUTION FOR VEHICLES THAT WERE BUILT DURING THE PERIOD WHEN VALVES WITH INADEQUATE RESISTANCE TO OZONE CRACKING WERE MOST LIKELY TO HAVE BEEN USED IN VEHICLE PRODUCTION.FURTHER INVESTIGATION OF THIS MATTER WOULD NOT BE AN EFFICIENT ALLOCATION OF AGENCY RESOURCES.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST.THE AGENCY WILL CONTINUE TO