NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
1,974 reports225,000 miles · Nov 4, 2022
Steering
The contact owns a 2008 Ford Escape. The contact stated while driving 25 MPH and coming to a complete stop, the steering wheel jerked and turned independently towards the left, almost causing the contact to lose control of the vehicle. There was no warning light illuminated. The contact stated that she steered the steering wheel…
Read full complaint
The contact owns a 2008 Ford Escape. The contact stated while driving 25 MPH and coming to a complete stop, the steering wheel jerked and turned independently towards the left, almost causing the contact to lose control of the vehicle. There was no warning light illuminated. The contact stated that she steered the steering wheel all the way to the right and then steered back to the center. The contact stated that the failure had been reoccurring while driving. The vehicle was taken to an independent mechanic where it was diagnosed that the steering shaft torque sensor kit and steering angle sensor calibration had failed and needed to be replaced. The independent mechanic informed the contact that the failure was associated with NHTSA Campaign Number: 14V284000 (Steering) and referred to the dealer for assistance. The vehicle was not repaired. The dealer and the manufacturer were notified of the failure and informed the contact that the vehicle could not be repaired under the recall as the VIN was not included. The failure mileage was approximately 225,000.
NHTSA ODI #11492295
144,000 miles · Nov 3, 2022
SteeringCrash
The contact owns a 2008 Ford Escape. The contact stated while driving 60 MPH, the steering wheel locked inadvertently and became significantly difficult to steer. A message indicating a power steering assist failure was displayed. The contact stated while attempting to veer to the side of the road, he lost control of the steerin…
Read full complaint
The contact owns a 2008 Ford Escape. The contact stated while driving 60 MPH, the steering wheel locked inadvertently and became significantly difficult to steer. A message indicating a power steering assist failure was displayed. The contact stated while attempting to veer to the side of the road, he lost control of the steering wheel and the vehicle struck a road construction barrier. The hood of the vehicle flew open and struck the windshield. The contact did not sustain an injury. The vehicle was towed to the residence. The contact stated that he was informed by the local Pep Boys that his vehicle had an electric power steering; therefore, he could not add power steering fluid. The dealer was notified of the failure and informed the contact that the failure was associated with NHTSA Campaign Number: 14V284000 (Steering). The manufacturer was notified of the failure and informed the contact that the vehicle could not be repaired under the recall as the VIN was not included. The failure mileage was approximately 144,000.
NHTSA ODI #11492083
Mileage unknown · Oct 19, 2022
Steering
Similar to the steering issues that others are experiencing, my Escape is pulling significantly to the right. I have had the suspension practically rebuilt, new tires put on and everything re-aligned, and the vehicle continues to pull to the right significantly. The mechanic checked with a local dealership who recognized that th…
Read full complaint
Similar to the steering issues that others are experiencing, my Escape is pulling significantly to the right. I have had the suspension practically rebuilt, new tires put on and everything re-aligned, and the vehicle continues to pull to the right significantly. The mechanic checked with a local dealership who recognized that there are steering recalls with this make and model year, however my VIN does not appear to be included in the recall. This is a very dangerous situation, because if a situation arose to where I had to correct my steering wheel to the right to avoid a collision or animal, I would likely easily lose control. There are no warning messages on my dash associated with this.
NHTSA ODI #11490018
Mileage unknown · Sep 17, 2022
Service Brakes
The brakes stopped working correctly and are very unsafe. The Regenerative brakes get disabled, and the ABS light is on, you lose the power brakes stopping power. I have to step on the brake pedal very hard for the vehicle to stop. It feels like the old school pre-power brakes. I took it to the Ford dealer, and they want to ch…
Read full complaint
The brakes stopped working correctly and are very unsafe. The Regenerative brakes get disabled, and the ABS light is on, you lose the power brakes stopping power. I have to step on the brake pedal very hard for the vehicle to stop. It feels like the old school pre-power brakes. I took it to the Ford dealer, and they want to charge 5000 + dollar to fix it, they also say parts are no longer available, they instructed me to call my insurance company and have it totaled. I read the escape hybrid forums and I see many people having this same problem
NHTSA ODI #11485000
Mileage unknown · Sep 9, 2022
Steering
I bought it 2 months ago it's happened to me three or four times now when I'm driving all of a sudden the power steering goes out and there's no power steering at all .I found out by turning it off and turning it back on it works the power steering but it's very dangerous all of a sudden it goes out. It's called the steering mod…
Read full complaint
I bought it 2 months ago it's happened to me three or four times now when I'm driving all of a sudden the power steering goes out and there's no power steering at all .I found out by turning it off and turning it back on it works the power steering but it's very dangerous all of a sudden it goes out. It's called the steering modular unit sensor. There's no warning or nothing it's loses all power steering. There was a recall on it when I first bought it I checked it out but now it's not there I don't know what happened to it. The car is available for inspection. I have not had it expected. I did have an appointment to get it looked at at the dealership but I canceled the appointment due to very hot temperatures that day. I wrote it down on a piece of paper what the recall said at that time and it said it was the steering modulator sensor something like that. If I can find it I will upload the paper.
NHTSA ODI #11483612
Mileage unknown · Sep 8, 2022
SuspensionWheels
Driving in the highway, the back shock absorber felt down crashing against the back right tire.
NHTSA ODI #11483446
145,000 miles · Sep 7, 2022
Steering
The contact owns a 2008 Ford Escape. The contact stated that while a friend was operating the vehicle, the power steering suddenly malfunctioned and the steering wheel became very difficult to turn in either direction. The vehicle was towed to the local dealer who diagnosed that the steering rack was faulty and needed to be repl…
Read full complaint
The contact owns a 2008 Ford Escape. The contact stated that while a friend was operating the vehicle, the power steering suddenly malfunctioned and the steering wheel became very difficult to turn in either direction. The vehicle was towed to the local dealer who diagnosed that the steering rack was faulty and needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure and advised that the VIN was not included in the NHTSA Campaign 14V284000 (Steering). The contact indicated that the vehicle had experienced the same failure listed in the recall. The failure mileage was 145,000.
NHTSA ODI #11483245
Mileage unknown · Aug 19, 2022
Electrical SystemUnknown Or Other
I HAVE BEEN HAVING PROBLEMS WITH THE IGNITION SWITCH FOR A FEW MONTHS . AT TIMES MY CAR WONT START. EVERYTHING COMES ON. iT FEELS VERY LOOSE AND HAVING TO PUSH IN THE KEY AND TURN IS VERY DIFFICULT AND HURTS MY HAND. PLUS THE ALARM BUTTON GETS PRESSED WHEN I TURN THE KEY.. i HAVE TO TURN KEY ON AND OFF WHILE PUSHING KEY INTO IGN…
Read full complaint
I HAVE BEEN HAVING PROBLEMS WITH THE IGNITION SWITCH FOR A FEW MONTHS . AT TIMES MY CAR WONT START. EVERYTHING COMES ON. iT FEELS VERY LOOSE AND HAVING TO PUSH IN THE KEY AND TURN IS VERY DIFFICULT AND HURTS MY HAND. PLUS THE ALARM BUTTON GETS PRESSED WHEN I TURN THE KEY.. i HAVE TO TURN KEY ON AND OFF WHILE PUSHING KEY INTO IGNITION SEVERAL TIMES AND PRAY THAT IT WILL CRANK. i HAVE HAD NO OTHER ISSUES OR REPAIRS THAT ARE NEEDED. i NOW HAVE MY CAR IN THE SHOP TO REPLACE THE IGNITION LOCK ASSEMBLY i HAVE AN ESTIMATE OF $400 FOR THIS REPAIR. i HAVE HEARD THIS IS A COMMON REPAIR FOR THIS PART ON THE VEHICLE I OWN.
NHTSA ODI #11480102
Mileage unknown · Aug 17, 2022
Forward Collision AvoidanceService Brakes
ABS light on, vehicle stalling, dragging while driving 40mph or over. Brake petal non functional. *c1313, c1480, c1481 Brake hoses restricted not allowing brake pressure in caliber *HCU damage *Sway bar links damage, excessive noise and play
NHTSA ODI #11479711
126,000 miles · Aug 9, 2022
Steering
The contact owns a 2008 Ford Escape. The contact stated that while driving at an undisclosed speed, the vehicle lost power steering functionality. The contact stated that the steering wheel was uncontrollable. There were no warning lights illuminated. The vehicle was taken to the local dealer to be diagnosed. The contact was inf…
Read full complaint
The contact owns a 2008 Ford Escape. The contact stated that while driving at an undisclosed speed, the vehicle lost power steering functionality. The contact stated that the steering wheel was uncontrollable. There were no warning lights illuminated. The vehicle was taken to the local dealer to be diagnosed. The contact was informed that the ignition module switch needed to be replaced. The contact was informed that parts were on backorder. The vehicle was not repaired. The contact stated that the failure was related to NHTSA Campaign Number: 14V284000 (Steering). The manufacturer was not contacted. The approximate failure mileage was 126,000.
NHTSA ODI #11478372
Official recalls
3Sep 29, 2015
Ford Motor Company (Ford) is recalling certain model year 2001-2008 Ford Escape and Mercury Mariner vehicles manufactured March 31, 2001, to September 1, 2009. The affected vehicles are equipped with either a 2.3L or 3.0L engine and have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.
Consequence & remedy
Consequence: If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "PARK" position, but the vehicle transmission may not actually be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.
Additional source detail variants (2)
Power Train:automatic Transmission:lever And Linkage:floor Shift
Ford Motor Company (Ford) is recalling certain model year 2001-2008 Ford Escape and Mercury Mariner vehicles manufactured March 31, 2001, to September 1, 2009. The affected vehicles are equipped with either a 2.3L or 3.0L engine and have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.
Consequence: If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "PARK" position, but the vehicle transmission may not actually be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.
Power Train:automatic Transmission:gear Position Indication (prndl)
Ford Motor Company (Ford) is recalling certain model year 2001-2008 Ford Escape and Mercury Mariner vehicles manufactured March 31, 2001, to September 1, 2009. The affected vehicles are equipped with either a 2.3L or 3.0L engine and have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.
Consequence: If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "PARK" position, but the vehicle transmission may not actually be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.
Sep 3, 2014
Ford Motor Company (Ford) is recalling certain model year 2005-2008 Ford Escape hybrid electric vehicles manufactured October 13, 2003, to June 20, 2008, and 2006-2008 Mercury Mariner hybrid electric vehicles manufactured June 10, 2005, to June 20, 2008. The coolant pump for the hybrid system may fail resulting in the hybrid electronics overheating.
Consequence & remedy
Consequence: If the hybrid electronics system overheats, it may shut down the powertrain, resulting in a stall-like condition, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will inspect and replace the original Motor Electronics Coolant (MEC) Pump with an improved brushless pump, free of charge. The recall is expected to begin on October 27, 2014. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 14S19.
May 29, 2014
Ford Motor Company (Ford) is recalling certain model year 2008-2011 Ford Escape and Mercury Mariner vehicles manufactured August 18, 2006, through September 11, 2010. The affected vehicles have a steering torque sensor that may not be able to properly detect driver steering input. As a result, the system could remove the Electric Power Steering (EPS) assist.
Consequence & remedy
Consequence: If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will update the software for the power steering control module (PSCM) and the instrument cluster module, free of charge. If a vehicle shows a history of a loss of the torque sensor signal or fault codes relating to the PSCM when the vehicle is brought in for the recall remedy, the affected components will be replaced, free of charge. The recall began on July 18, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S05.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3DP15001 · Loss Of Power Steering While Driving
Opened Apr 1, 2015 · Closed Jun 14, 2018
Status: closed (inferred from source dates) · Steering:electric Power Assist System
On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric power assisted steering (NHTSA 14V-284, Ford 14S05). Ford's DIR described the defect condition as a poor signal to noise ratio [SNR] in the torque sensor within the Electric Power Assisted Steering (EPAS) system [which] does not allow the PSCM to determine the driver's steering input. When the system detects this fault condition, it transitions the EPAS system to the fail-safe/manual steering mode.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Ford's remedy instructs dealers to check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTCs) to determine the proper repair procedure. If no DTCs are present, dealers are to update the PSCM and instrument cluster module software. The updated PSCM software changes the torque sensor fault strategy so that the SNR condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If DTCs indicating faults in the torque sensor, PSCM or Power Steering Motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (DTC B2278); or 2) replaces the steering column for faults related to the PSCM (DTC B1342) or motor (DTC B2277).Continued in attachment pages
DP12006 · Electronic Throttle Body Malfunction
Opened Oct 2, 2012 · Closed Feb 21, 2013
Status: closed (inferred from source dates) · Engine
In a letter dated August 30, 2012, The North Carolina Consumers Council (NCCC) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged electronic throttle body failures resulting in engine stall or surge while driving in model year (MY) 2005 through 2012 Ford Escape vehicles. On October 2, 2012 the Office of Defects Investigation (ODI) opened a Defect Petition DP12-006 to evaluate whether to grant or deny the petition. The petition is hereby granted on certain model years. The NCCC letter cites two complaints of stall while driving in MY 2009 Ford Escape vehicles that were diagnosed as failed throttle bodies with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed. The petitioner indicates that the owners of both vehicles reported experiencing repeated incidents of stalling and engine surging. According to Ford, Escape non-hybrid vehicles are equipped with Electronic Throttle Body (ETB) assemblies beginning with MY 2009. Vehicles manufactured between June 22, 2009 and October 15, 2009 may contain contaminated printed circuit boards (PCB) with plating variations. Plating variations could lead to a lack of continuity in the throttle position sensor circuit where P2111 and/or other DTCs would be generated and stored. Ford and its electronic throttle body supplier, Delphi, modified the PCB manufacturing process and issued a technical service bulletin (TSB) 09-23-5. Vehicles produced after October 15, 2009 incorporated ETBs manufactured with a PCB process that resolved this condition. ODI's analysis identified a total of 123 unique reports indicating allegations of reduced motive power or vehicle stall. Depending on the condition of throttle control system malfunction, a driver may experience varying levels of reduced engine performance associated with three limp home modes. In two limp modes, reduced engine performance may maintain vehicle speeds above 20mph while the third is a limited limp home mode with engine speeds limited to approximately 900 RPM. Allegations of stall appear to be related to the limited limp home mode. Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability. Allegations of vehicle surge appear to be related to limp home mode operation. Complaints alleging surge are most likely related to engine RPM fluctuations at low vehicle speeds or idle as the control system engages to prevent engine stall. In limited limp mode, rough-idle conditions may exist while the control system attempts to modulate engine RPMs once the vehicle reaches a reduced speed to maintain approximately 900 RPM. Separately, ODI received 59 complaints alleging incidents of engine stall while driving in model year (MY) 2010-2011 Ford Fusion vehicles. Approximately 60 percent (36) of the incidents occurred at speeds of 40 miles per hour or more. Eighty percent of complaints (47) were received beginning March 2012 and 14 complaints reported that the throttle body was replaced or DTCs associated with limp home modes. Additionally, Ford issued TSB 10-21-6 addressing DTCs associated with idle speed drops and limited limp home mode. The petition is granted on certain model years.Preliminary Evaluation PE13-003 has been opened to assess the scope, frequency and potential safety consequences associated with the alleged defect.See full copy of the closing resume for this defect petition for list of the VOQs associated with the defect petition analysis.
PE08060 · Tire Valve Cracking
Opened Oct 14, 2008 · Closed Apr 9, 2009
Status: closed (inferred from source dates) · Tires:valve
ON OCTOBER 14, 2008, ODI OPENED PE08-060 TO INVESTIGATE ALLEGATIONS OF CRACKED AND LEAKING SNAP-IN TIRE VALVES IN MODEL YEAR (MY) 2007 VEHICLES MANUFACTURED BY FORD MOTOR COMPANY.THE VALVES WERE SUPPLIED TO FORD BY TOPSEAL AUTO-PARTS, A SUBSIDIARY OF THE SHANGHAI BAOLONG AUTOMOTIVE CORPORATION IN CHINA.VALVES MADE BY TOPSEAL FOR AFTERMARKET SALE WERE THE SUBJECT OF TWO RECENT SAFETY RECALLS BY TECH INTERNATIONAL (08T-018) AND DILL AIR CONTROLS (08T-028), THE LATTER OF WHICH WAS INVESTIGATED BY ODI IN PE08-036 AND EA08-022.THE DEFECT CONDITIONS ADDRESSED BY THE AFTERMARKET TIRE VALVE RECALLS BOTH INVOLVED INADEQUATE RESISTANCE TO OZONE CRACKING DUE TO ISSUES WITH THE SUPPLY OF ANTI-OZONANT CHEMICALS TO TOPSEAL FOR A PERIOD FROM JULY TO MID-NOVEMBER 2006.THE AFTERMARKET VALVES WERE COMPOUNDED WITH A BLEND OF EPDM AND NATURAL RUBBER, USING A RELATIVELY LOW PERCENTAGE OF EPDM (EPDM PROVIDES INHERENT RESISTANCE TO OZONE CRACKING).HENCE, THE NEED FOR ANTI-OZONANT CHEMICALS AND THE PROBLEMS WITH CRACKING WHEN THOSE CHEMICALS WERE MISSING OR OUT OF SPECIFICATION IN SOME LOTS OF VALVES.BOTH RECALL CAMPAIGNS INVOLVED INSPECTION PROGRAMS TO IDENTIFY AND REPLACE VALVES WITH VISIBLE SURFACE CRACKING.ALTHOUGH THE TOPSEAL VALVES SUPPLIED TO FORD ALSO APPEAR TO HAVE BEEN AFFECTED BY THE ANTI-OZONANT SUPPLY ISSUES IN MID TO LATE-2006, FORD INDICATED THAT ITS VALVES WERE MADE AT A DIFFERENT TOPSEAL PRODUCTION LINE AND WERE COMPOUNDED WITH A HIGHER PERCENTAGE OF EPDM RUBBER TO MEET MORE STRINGENT SPECIFICATIONS FROM FORD.ODI'S ANALYSIS OF COMPLAINT AND WARRANTY DATA PROVIDED BY FORD SHOWED THAT PROBLEMS WITH CRACKED TIRE VALVES WERE SIGNIFICANTLY HIGHER FOR MY 2007 VEHICLES PRODUCED FROM DECEMBER 2006 THROUGH MARCH 2007.FORD RESPONDED BY IMPLEMENTING CHANGES IN ITS MATERIAL SPECIFICATIONS FOR SNAP-IN RUBBER TIRE VALVES AND ALSO INCREASING THE QUALITY AND ACCEPTANCE STANDARDS FOR VALVES IMPORTED FOR USE IN ITS VEHICLES.WHILE THE COMPLAINT AND WARRANTY CLAIM RATES ARE ELEVATED FOR SUBJECT VEHICLES PRODUCED FROM DECEMBER 2006 THROUGH MARCH 2007, THE RATES OF LEAKING VALVES ARE WELL BELOW ONE PERCENT OF PRODUCTION FOR EACH OF THE PEAK MONTHS FOR ALL OF THE AFFECTED MODELS.A SUBSTANTIAL MAJORITY OF THE SUBJECT VEHICLES ARE EQUIPPED WITH TIRE PRESSURE MONITORING SYSTEMS (TPMS) WHICH WARN THE DRIVER WHEN ANY TIRE PRESSURES DROPS BELOW 25 PERCENT OF RECOMMENDED INFLATION PRESSURE. AS OUTLINED IN A LETTER TO ODI DATED APRIL 6, 2009, FORD HAS AGREED TO SEND LETTERS TO OWNERS OF CERTAIN MY 2007 AND 2008 FORD, LINCOLN AND MERCURY VEHICLES TO PROVIDE INFORMATION ABOUT THE CRACKING CONCERN. LETTERS WILL BE SENT TO OWNERS OF VEHICLES BUILT FROM NOVEMBER 2006 THROUGH MAY 2007.OWNERS CAN OPT FOR A FREE DEALER INSPECTION.VALVES EXHIBITING SURFACE CRACKS OR AIR LEAKAGE RELATED TO OZONE ATTACK WILL BE REPLACED BY FORD UNDER ITS NORMAL WARRANTY TERMS.FORD EXPECTS TO SEND THE LETTER BY APPROXIMATELY MID-MAY 2009. BASED ON THE USE OF TPMS IN THE MAJORITY OF SUBJECT VEHICLES AND THE RELATIVELY LOW RATES OF REPAIRS ASSOCIATED WITH LEAKING VALVES AND RESULTANT TIRE DAMAGE, ODI BELIEVES THAT THE ACTIONS FORD HAS AGREED TO TAKE WILL PROVIDE EFFECTIVE AND EXPEDITIOUS RESOLUTION FOR VEHICLES THAT WERE BUILT DURING THE PERIOD WHEN VALVES WITH INADEQUATE RESISTANCE TO OZONE CRACKING WERE MOST LIKELY TO HAVE BEEN USED IN VEHICLE PRODUCTION.FURTHER INVESTIGATION OF THIS MATTER WOULD NOT BE AN EFFICIENT ALLOCATION OF AGENCY RESOURCES.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST.THE AGENCY WILL CONTINUE TO
Illustration