The power steering torque sensor failed while driving today. As a result the vehicle lost all power steering and became difficult to steer and posed a serious risk to my safety while driving a distance over an hour from home on back country roads in Kentucky which were winding and made making curves and staying on the road very …
Read full complaint
The power steering torque sensor failed while driving today. As a result the vehicle lost all power steering and became difficult to steer and posed a serious risk to my safety while driving a distance over an hour from home on back country roads in Kentucky which were winding and made making curves and staying on the road very difficult to manage. There was no warning, no engine check light to come on. About 5 minutes before the power steering failed to function, the steering wheel began to have a very slight movement while at a stop light. This was not a sufficient warning to give me enough time to determine that my vehicle was about to become unsafe and there was no noise coming from the car or affected components. As a result of the malfunction/ equipment failure, I had to make wide turns that made the vehicle leave the roadway slightly at times with the tires going off the side of the road before the wide turn was completed. Steering became very difficult and the vehicle did not respond to my steering attempts. I could not make sharp turns and had a long distance to suffer through the hazard this caused. When I finally arrived home I had to drive through my yard to park because I could not get the vehicle to turn sharp enough to make it into the driveway. While driving there wasn't any shake or noticeable issue with the steering wheel itself other than the loss of power steering that felt as if the entire steering column was locked up. I have contacted the nearest Ford dealership to inquire about getting the recall repair completed tomorrow. I will have it inspected at that time. As of now, the failed component is available for inspection upon request. I am sure the problem will be reproduced as it has not regained steering function hours later and is in need of repair. I never received any notice prior to the equipment failure that there in fact was a safety recall on my vehicle. I would like to know how I was missed on being notified.
NHTSA ODI #11498329
Mileage unknown · Dec 19, 2022
Electrical SystemSteering
Electric power steering system not working causing the vehicle to default to manual steering which makes the vehicle extremely hard to drive. My safety is at risk because I do not have sufficient control of the steering of the vehicle. The car has been inspected by the dealership. There were no signs or lamps prior to the proble…
Read full complaint
Electric power steering system not working causing the vehicle to default to manual steering which makes the vehicle extremely hard to drive. My safety is at risk because I do not have sufficient control of the steering of the vehicle. The car has been inspected by the dealership. There were no signs or lamps prior to the problem starting.
NHTSA ODI #11498001
160,000 miles · Nov 29, 2022
Steering
The contact owns a 2008 Ford Escape. The contact stated while driving 45-50 MPH, the power steering assist failed temporarily. There was no warning light illuminated. The contact stated that the failure reoccurred increasingly while driving. The contact stated that the vehicle was not drivable. The message "Power Steering Assist…
Read full complaint
The contact owns a 2008 Ford Escape. The contact stated while driving 45-50 MPH, the power steering assist failed temporarily. There was no warning light illuminated. The contact stated that the failure reoccurred increasingly while driving. The contact stated that the vehicle was not drivable. The message "Power Steering Assist Failure" was displayed. An unknown dealer was notified of the failure and informed the contact that the VIN was not under recall. The vehicle was not diagnosed or repaired. The contact associated the failure with NHTSA Campaign Number: 14V284000 (Steering). The manufacturer was notified of the failure but provided no assistance. The manufacturer referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 160,000.
NHTSA ODI #11495343
Mileage unknown · Nov 18, 2022
Seat BeltsSteering
The seatbelt shoulder strap will lock and will not unlock unless you release the buckle. We came out one morning and had no power steering it is equipped with electronic power assist The dealer said that there were no recalls for this particular condition. I found out from a shop that I used to work for that there were. My wife …
Read full complaint
The seatbelt shoulder strap will lock and will not unlock unless you release the buckle. We came out one morning and had no power steering it is equipped with electronic power assist The dealer said that there were no recalls for this particular condition. I found out from a shop that I used to work for that there were. My wife cannot drive the vehicle in this condition via surgurey. Thanks for listenig.
NHTSA ODI #11494191
100,054 miles · Nov 15, 2022
Steering
The contact owns a 2008 Ford Edge. The contact stated that while driving at an undisclosed speed, the steering wheel locked up and became difficult to turn. After restarting the vehicle, the steering operated as designed. There were no warning lights illuminated. The vehicle was taken to the local dealer however, the mechanic wa…
Read full complaint
The contact owns a 2008 Ford Edge. The contact stated that while driving at an undisclosed speed, the steering wheel locked up and became difficult to turn. After restarting the vehicle, the steering operated as designed. There were no warning lights illuminated. The vehicle was taken to the local dealer however, the mechanic was unable to determine the cause of the failure and referred her to another dealer. The vehicle was not repaired. The contact stated that the failure was related to NHTSA Campaign Number: 14V284000 (Steering). The manufacturer was notified of the failure but provided no additional assistance. The failure mileage was approximately 100,054.
NHTSA ODI #11493701
225,000 miles · Nov 4, 2022
Steering
The contact owns a 2008 Ford Escape. The contact stated while driving 25 MPH and coming to a complete stop, the steering wheel jerked and turned independently towards the left, almost causing the contact to lose control of the vehicle. There was no warning light illuminated. The contact stated that she steered the steering wheel…
Read full complaint
The contact owns a 2008 Ford Escape. The contact stated while driving 25 MPH and coming to a complete stop, the steering wheel jerked and turned independently towards the left, almost causing the contact to lose control of the vehicle. There was no warning light illuminated. The contact stated that she steered the steering wheel all the way to the right and then steered back to the center. The contact stated that the failure had been reoccurring while driving. The vehicle was taken to an independent mechanic where it was diagnosed that the steering shaft torque sensor kit and steering angle sensor calibration had failed and needed to be replaced. The independent mechanic informed the contact that the failure was associated with NHTSA Campaign Number: 14V284000 (Steering) and referred to the dealer for assistance. The vehicle was not repaired. The dealer and the manufacturer were notified of the failure and informed the contact that the vehicle could not be repaired under the recall as the VIN was not included. The failure mileage was approximately 225,000.
NHTSA ODI #11492295
144,000 miles · Nov 3, 2022
SteeringCrash
The contact owns a 2008 Ford Escape. The contact stated while driving 60 MPH, the steering wheel locked inadvertently and became significantly difficult to steer. A message indicating a power steering assist failure was displayed. The contact stated while attempting to veer to the side of the road, he lost control of the steerin…
Read full complaint
The contact owns a 2008 Ford Escape. The contact stated while driving 60 MPH, the steering wheel locked inadvertently and became significantly difficult to steer. A message indicating a power steering assist failure was displayed. The contact stated while attempting to veer to the side of the road, he lost control of the steering wheel and the vehicle struck a road construction barrier. The hood of the vehicle flew open and struck the windshield. The contact did not sustain an injury. The vehicle was towed to the residence. The contact stated that he was informed by the local Pep Boys that his vehicle had an electric power steering; therefore, he could not add power steering fluid. The dealer was notified of the failure and informed the contact that the failure was associated with NHTSA Campaign Number: 14V284000 (Steering). The manufacturer was notified of the failure and informed the contact that the vehicle could not be repaired under the recall as the VIN was not included. The failure mileage was approximately 144,000.
NHTSA ODI #11492083
Mileage unknown · Oct 19, 2022
Steering
Similar to the steering issues that others are experiencing, my Escape is pulling significantly to the right. I have had the suspension practically rebuilt, new tires put on and everything re-aligned, and the vehicle continues to pull to the right significantly. The mechanic checked with a local dealership who recognized that th…
Read full complaint
Similar to the steering issues that others are experiencing, my Escape is pulling significantly to the right. I have had the suspension practically rebuilt, new tires put on and everything re-aligned, and the vehicle continues to pull to the right significantly. The mechanic checked with a local dealership who recognized that there are steering recalls with this make and model year, however my VIN does not appear to be included in the recall. This is a very dangerous situation, because if a situation arose to where I had to correct my steering wheel to the right to avoid a collision or animal, I would likely easily lose control. There are no warning messages on my dash associated with this.
NHTSA ODI #11490018
Mileage unknown · Sep 9, 2022
Steering
I bought it 2 months ago it's happened to me three or four times now when I'm driving all of a sudden the power steering goes out and there's no power steering at all .I found out by turning it off and turning it back on it works the power steering but it's very dangerous all of a sudden it goes out. It's called the steering mod…
Read full complaint
I bought it 2 months ago it's happened to me three or four times now when I'm driving all of a sudden the power steering goes out and there's no power steering at all .I found out by turning it off and turning it back on it works the power steering but it's very dangerous all of a sudden it goes out. It's called the steering modular unit sensor. There's no warning or nothing it's loses all power steering. There was a recall on it when I first bought it I checked it out but now it's not there I don't know what happened to it. The car is available for inspection. I have not had it expected. I did have an appointment to get it looked at at the dealership but I canceled the appointment due to very hot temperatures that day. I wrote it down on a piece of paper what the recall said at that time and it said it was the steering modulator sensor something like that. If I can find it I will upload the paper.
NHTSA ODI #11483612
145,000 miles · Sep 7, 2022
Steering
The contact owns a 2008 Ford Escape. The contact stated that while a friend was operating the vehicle, the power steering suddenly malfunctioned and the steering wheel became very difficult to turn in either direction. The vehicle was towed to the local dealer who diagnosed that the steering rack was faulty and needed to be repl…
Read full complaint
The contact owns a 2008 Ford Escape. The contact stated that while a friend was operating the vehicle, the power steering suddenly malfunctioned and the steering wheel became very difficult to turn in either direction. The vehicle was towed to the local dealer who diagnosed that the steering rack was faulty and needed to be replaced. The vehicle was not yet repaired. The manufacturer was notified of the failure and advised that the VIN was not included in the NHTSA Campaign 14V284000 (Steering). The contact indicated that the vehicle had experienced the same failure listed in the recall. The failure mileage was 145,000.
Ford Motor Company (Ford) is recalling certain model year 2001-2008 Ford Escape and Mercury Mariner vehicles manufactured March 31, 2001, to September 1, 2009. The affected vehicles are equipped with either a 2.3L or 3.0L engine and have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.
Consequence & remedy
Consequence: If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "PARK" position, but the vehicle transmission may not actually be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.
Additional source detail variants (2)
Power Train:automatic Transmission:lever And Linkage:floor Shift
Ford Motor Company (Ford) is recalling certain model year 2001-2008 Ford Escape and Mercury Mariner vehicles manufactured March 31, 2001, to September 1, 2009. The affected vehicles are equipped with either a 2.3L or 3.0L engine and have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.
Consequence: If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "PARK" position, but the vehicle transmission may not actually be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.
Power Train:automatic Transmission:gear Position Indication (prndl)
Ford Motor Company (Ford) is recalling certain model year 2001-2008 Ford Escape and Mercury Mariner vehicles manufactured March 31, 2001, to September 1, 2009. The affected vehicles are equipped with either a 2.3L or 3.0L engine and have had their CD4E transmission replaced with remanufactured one that was rebuilt between June 11, 2015 through July 15, 2015. These service repair part transmissions have a shift lever bolt that may not be properly tightened. As a result, the shift control lever could disengage from the transmission without warning.
Consequence: If the shift lever disengages from the transmission, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the gear selection indicator may show that the transmission is in the "PARK" position, but the vehicle transmission may not actually be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the transmissions and either tighten the manual shift lever bolt or replace the manual shift lever assembly. These repairs will be performed free of charge. The recall began on October 23, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S28.
Ford Motor Company (Ford) is recalling certain model year 2005-2008 Ford Escape hybrid electric vehicles manufactured October 13, 2003, to June 20, 2008, and 2006-2008 Mercury Mariner hybrid electric vehicles manufactured June 10, 2005, to June 20, 2008. The coolant pump for the hybrid system may fail resulting in the hybrid electronics overheating.
Consequence & remedy
Consequence: If the hybrid electronics system overheats, it may shut down the powertrain, resulting in a stall-like condition, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will inspect and replace the original Motor Electronics Coolant (MEC) Pump with an improved brushless pump, free of charge. The recall is expected to begin on October 27, 2014. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 14S19.
Ford Motor Company (Ford) is recalling certain model year 2008-2011 Ford Escape and Mercury Mariner vehicles manufactured August 18, 2006, through September 11, 2010. The affected vehicles have a steering torque sensor that may not be able to properly detect driver steering input. As a result, the system could remove the Electric Power Steering (EPS) assist.
Consequence & remedy
Consequence: If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will update the software for the power steering control module (PSCM) and the instrument cluster module, free of charge. If a vehicle shows a history of a loss of the torque sensor signal or fault codes relating to the PSCM when the vehicle is brought in for the recall remedy, the affected components will be replaced, free of charge. The recall began on July 18, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S05.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3
DP15001 · Loss Of Power Steering While Driving
Opened Apr 1, 2015 · Closed Jun 14, 2018
Status: closed (inferred from source dates) · Steering:electric Power Assist System
On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric power assisted steering (NHTSA 14V-284, Ford 14S05). Ford's DIR described the defect condition as a poor signal to noise ratio [SNR] in the torque sensor within the Electric Power Assisted Steering (EPAS) system [which] does not allow the PSCM to determine the driver's steering input. When the system detects this fault condition, it transitions the EPAS system to the fail-safe/manual steering mode.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Ford's remedy instructs dealers to check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTCs) to determine the proper repair procedure. If no DTCs are present, dealers are to update the PSCM and instrument cluster module software. The updated PSCM software changes the torque sensor fault strategy so that the SNR condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If DTCs indicating faults in the torque sensor, PSCM or Power Steering Motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (DTC B2278); or 2) replaces the steering column for faults related to the PSCM (DTC B1342) or motor (DTC B2277).Continued in attachment pages
DP12006 · Electronic Throttle Body Malfunction
Opened Oct 2, 2012 · Closed Feb 21, 2013
Status: closed (inferred from source dates) · Engine
In a letter dated August 30, 2012, The North Carolina Consumers Council (NCCC) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged electronic throttle body failures resulting in engine stall or surge while driving in model year (MY) 2005 through 2012 Ford Escape vehicles. On October 2, 2012 the Office of Defects Investigation (ODI) opened a Defect Petition DP12-006 to evaluate whether to grant or deny the petition. The petition is hereby granted on certain model years. The NCCC letter cites two complaints of stall while driving in MY 2009 Ford Escape vehicles that were diagnosed as failed throttle bodies with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed. The petitioner indicates that the owners of both vehicles reported experiencing repeated incidents of stalling and engine surging. According to Ford, Escape non-hybrid vehicles are equipped with Electronic Throttle Body (ETB) assemblies beginning with MY 2009. Vehicles manufactured between June 22, 2009 and October 15, 2009 may contain contaminated printed circuit boards (PCB) with plating variations. Plating variations could lead to a lack of continuity in the throttle position sensor circuit where P2111 and/or other DTCs would be generated and stored. Ford and its electronic throttle body supplier, Delphi, modified the PCB manufacturing process and issued a technical service bulletin (TSB) 09-23-5. Vehicles produced after October 15, 2009 incorporated ETBs manufactured with a PCB process that resolved this condition. ODI's analysis identified a total of 123 unique reports indicating allegations of reduced motive power or vehicle stall. Depending on the condition of throttle control system malfunction, a driver may experience varying levels of reduced engine performance associated with three limp home modes. In two limp modes, reduced engine performance may maintain vehicle speeds above 20mph while the third is a limited limp home mode with engine speeds limited to approximately 900 RPM. Allegations of stall appear to be related to the limited limp home mode. Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability. Allegations of vehicle surge appear to be related to limp home mode operation. Complaints alleging surge are most likely related to engine RPM fluctuations at low vehicle speeds or idle as the control system engages to prevent engine stall. In limited limp mode, rough-idle conditions may exist while the control system attempts to modulate engine RPMs once the vehicle reaches a reduced speed to maintain approximately 900 RPM. Separately, ODI received 59 complaints alleging incidents of engine stall while driving in model year (MY) 2010-2011 Ford Fusion vehicles. Approximately 60 percent (36) of the incidents occurred at speeds of 40 miles per hour or more. Eighty percent of complaints (47) were received beginning March 2012 and 14 complaints reported that the throttle body was replaced or DTCs associated with limp home modes. Additionally, Ford issued TSB 10-21-6 addressing DTCs associated with idle speed drops and limited limp home mode. The petition is granted on certain model years.Preliminary Evaluation PE13-003 has been opened to assess the scope, frequency and potential safety consequences associated with the alleged defect.See full copy of the closing resume for this defect petition for list of the VOQs associated with the defect petition analysis.
PE08060 · Tire Valve Cracking
Opened Oct 14, 2008 · Closed Apr 9, 2009
Status: closed (inferred from source dates) · Tires:valve
ON OCTOBER 14, 2008, ODI OPENED PE08-060 TO INVESTIGATE ALLEGATIONS OF CRACKED AND LEAKING SNAP-IN TIRE VALVES IN MODEL YEAR (MY) 2007 VEHICLES MANUFACTURED BY FORD MOTOR COMPANY.THE VALVES WERE SUPPLIED TO FORD BY TOPSEAL AUTO-PARTS, A SUBSIDIARY OF THE SHANGHAI BAOLONG AUTOMOTIVE CORPORATION IN CHINA.VALVES MADE BY TOPSEAL FOR AFTERMARKET SALE WERE THE SUBJECT OF TWO RECENT SAFETY RECALLS BY TECH INTERNATIONAL (08T-018) AND DILL AIR CONTROLS (08T-028), THE LATTER OF WHICH WAS INVESTIGATED BY ODI IN PE08-036 AND EA08-022.THE DEFECT CONDITIONS ADDRESSED BY THE AFTERMARKET TIRE VALVE RECALLS BOTH INVOLVED INADEQUATE RESISTANCE TO OZONE CRACKING DUE TO ISSUES WITH THE SUPPLY OF ANTI-OZONANT CHEMICALS TO TOPSEAL FOR A PERIOD FROM JULY TO MID-NOVEMBER 2006.THE AFTERMARKET VALVES WERE COMPOUNDED WITH A BLEND OF EPDM AND NATURAL RUBBER, USING A RELATIVELY LOW PERCENTAGE OF EPDM (EPDM PROVIDES INHERENT RESISTANCE TO OZONE CRACKING).HENCE, THE NEED FOR ANTI-OZONANT CHEMICALS AND THE PROBLEMS WITH CRACKING WHEN THOSE CHEMICALS WERE MISSING OR OUT OF SPECIFICATION IN SOME LOTS OF VALVES.BOTH RECALL CAMPAIGNS INVOLVED INSPECTION PROGRAMS TO IDENTIFY AND REPLACE VALVES WITH VISIBLE SURFACE CRACKING.ALTHOUGH THE TOPSEAL VALVES SUPPLIED TO FORD ALSO APPEAR TO HAVE BEEN AFFECTED BY THE ANTI-OZONANT SUPPLY ISSUES IN MID TO LATE-2006, FORD INDICATED THAT ITS VALVES WERE MADE AT A DIFFERENT TOPSEAL PRODUCTION LINE AND WERE COMPOUNDED WITH A HIGHER PERCENTAGE OF EPDM RUBBER TO MEET MORE STRINGENT SPECIFICATIONS FROM FORD.ODI'S ANALYSIS OF COMPLAINT AND WARRANTY DATA PROVIDED BY FORD SHOWED THAT PROBLEMS WITH CRACKED TIRE VALVES WERE SIGNIFICANTLY HIGHER FOR MY 2007 VEHICLES PRODUCED FROM DECEMBER 2006 THROUGH MARCH 2007.FORD RESPONDED BY IMPLEMENTING CHANGES IN ITS MATERIAL SPECIFICATIONS FOR SNAP-IN RUBBER TIRE VALVES AND ALSO INCREASING THE QUALITY AND ACCEPTANCE STANDARDS FOR VALVES IMPORTED FOR USE IN ITS VEHICLES.WHILE THE COMPLAINT AND WARRANTY CLAIM RATES ARE ELEVATED FOR SUBJECT VEHICLES PRODUCED FROM DECEMBER 2006 THROUGH MARCH 2007, THE RATES OF LEAKING VALVES ARE WELL BELOW ONE PERCENT OF PRODUCTION FOR EACH OF THE PEAK MONTHS FOR ALL OF THE AFFECTED MODELS.A SUBSTANTIAL MAJORITY OF THE SUBJECT VEHICLES ARE EQUIPPED WITH TIRE PRESSURE MONITORING SYSTEMS (TPMS) WHICH WARN THE DRIVER WHEN ANY TIRE PRESSURES DROPS BELOW 25 PERCENT OF RECOMMENDED INFLATION PRESSURE. AS OUTLINED IN A LETTER TO ODI DATED APRIL 6, 2009, FORD HAS AGREED TO SEND LETTERS TO OWNERS OF CERTAIN MY 2007 AND 2008 FORD, LINCOLN AND MERCURY VEHICLES TO PROVIDE INFORMATION ABOUT THE CRACKING CONCERN. LETTERS WILL BE SENT TO OWNERS OF VEHICLES BUILT FROM NOVEMBER 2006 THROUGH MAY 2007.OWNERS CAN OPT FOR A FREE DEALER INSPECTION.VALVES EXHIBITING SURFACE CRACKS OR AIR LEAKAGE RELATED TO OZONE ATTACK WILL BE REPLACED BY FORD UNDER ITS NORMAL WARRANTY TERMS.FORD EXPECTS TO SEND THE LETTER BY APPROXIMATELY MID-MAY 2009. BASED ON THE USE OF TPMS IN THE MAJORITY OF SUBJECT VEHICLES AND THE RELATIVELY LOW RATES OF REPAIRS ASSOCIATED WITH LEAKING VALVES AND RESULTANT TIRE DAMAGE, ODI BELIEVES THAT THE ACTIONS FORD HAS AGREED TO TAKE WILL PROVIDE EFFECTIVE AND EXPEDITIOUS RESOLUTION FOR VEHICLES THAT WERE BUILT DURING THE PERIOD WHEN VALVES WITH INADEQUATE RESISTANCE TO OZONE CRACKING WERE MOST LIKELY TO HAVE BEEN USED IN VEHICLE PRODUCTION.FURTHER INVESTIGATION OF THIS MATTER WOULD NOT BE AN EFFICIENT ALLOCATION OF AGENCY RESOURCES.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT A SAFETY-RELATED DEFECT DOES NOT EXIST.THE AGENCY WILL CONTINUE TO
Illustration