IllustrationDash is saying rearview camera is unavailable please contact the dealership
2013 Ford Edge
Owner reports · Recalls · Investigations
More warning signs than most Edge years
Owner complaints for the 2013 Ford Edge are substantially higher than the model-year median of 724.
About this comparison →How this year compares
Owner complaints by model year
Compare all Edge years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1470–25K
63025–50K
50950–75K
24575–100K
206100–150K
56150K+
1,793 reports with mileage · 651 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 854 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 529 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 300 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
33 crash reports7 fire reports24 injury reports
What owners actually said
2,444 reportsThe driver side passenger "door ajar" sensor stays on constantly and is unsafe because we aren't sure if the door is truly open or not? We are scared to have passengers sit on that side of the vehicle for fear of the door flying open and causing injury by falling out or other injury because the sensor does not tell us accuratel…
Read full complaint
The driver side passenger "door ajar" sensor stays on constantly and is unsafe because we aren't sure if the door is truly open or not? We are scared to have passengers sit on that side of the vehicle for fear of the door flying open and causing injury by falling out or other injury because the sensor does not tell us accurately as to whether the door is truly closed all the way or not. It also drains the battery over time due to constantly being on. This problem has been going on for 2 years. We had it looked at by a mechanic. We were told they can replace the sensor, but it would likely go out again because this is a manufacturer defect, and a well known problem for Ford Edges as well as other Ford models, but they refuse to issue a recall. This is EXTREMELY UNSAFE. The other safety concern I have is the need for a recall on our VIN SPECIFIC rear view camera. The screen went blank and then, when it came back on, the image is flipped upside down and has vertical lines across the screen making it extremely difficult to see. This is a crucial component to safety. This happened approximately 1 year ago. This is EXTREMELY UNSAFE as we can back over and KILL someone if we don't go super slow and intensely observe the camera while in reverse. This is even more dangerous in poorly lit places. There were no warnings or sensors indicating a problem with the camera. It just went blank and then PERMANENTLY flipped the image upside down.
The backup camera is sometimes upside down, flashes, or won't come on at all. Various things other than functioning properly. I've completed the Sync update and that didn't resolve the issue. This started happening around the same time newer Ford models were showing the exact same issues.
The rear back up camera image is inverted. I see that the 2015-2018s were recalled but this is also happening with the 2013s
Was going 70 mph (speed limit) and hit a deer, car was totaled. Upon impact my seatbelt locked up and I smelled smoke, but the airbags didn't actually deploy. No warning signs or prior issues known.
The 2013 Ford Edge began giving trouble after sitting at an intersection or pulling out of the driveway to enter major traffic. The vehicle would hesitate to accelerate as though it is running out of gas but it isn't out of gas. When you continue pressing on the accelerator it would jerk then accelerate. We barely escaped being …
Read full complaint
The 2013 Ford Edge began giving trouble after sitting at an intersection or pulling out of the driveway to enter major traffic. The vehicle would hesitate to accelerate as though it is running out of gas but it isn't out of gas. When you continue pressing on the accelerator it would jerk then accelerate. We barely escaped being hit from the rear because the vehicle died while pulling out onto the feeder, whereupon I struggled to pull into a nearby gas station. The brake pedal is generally stiff but can be depressed, however, in other instances, when braking the brake pedal sometimes becomes hard to depress but becomes easier after the car is driving for a long stretch, such as the freeway. When you start the car the panel is normal but as you begin driving the Check Brake System failure light begins to appear in Red and the ABS light and the oil light. Similar incidents as the previously mentioned situations have happened on numerous occasions.
The contact owns a 2013 Ford Edge. The contact stated that while driving at a slow speed and taking a right turn, while attempting to depress the brake pedal, the brake pedal felt mushy. The contact stated that excessive force was required to depress the brake pedal. The contact stated that the brake pedal had lost pressure for …
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while driving at a slow speed and taking a right turn, while attempting to depress the brake pedal, the brake pedal felt mushy. The contact stated that excessive force was required to depress the brake pedal. The contact stated that the brake pedal had lost pressure for a moment. There was no warning light illuminated. The local dealer was contacted; however, the vehicle was not diagnosed because the VIN was not under an open recall. The vehicle was not repaired. The contact referenced Customer Satisfaction Program: 13N02, as a possible cause for the failure. The manufacturer was notified of the failure. The approximate failure mileage was 135,000.
The rearview camera does not function properly. Most of the time, it shows a blank screen or nothing at all. Sometimes it tells me to contact the dealership. Other times, it shows the camera view but upside down. It puts myself and others at risk because I can't see clearly when I am backing up. The problem is covered by a known…
Read full complaint
The rearview camera does not function properly. Most of the time, it shows a blank screen or nothing at all. Sometimes it tells me to contact the dealership. Other times, it shows the camera view but upside down. It puts myself and others at risk because I can't see clearly when I am backing up. The problem is covered by a known recall. However, my vehicle is not covered by the recall.
A few years ago, I brought my Edge into a dealership in Shawnee Mission, KS (Shawnee Mission Ford) for the rearview camera malfunctioning. What occurs is, once I put the car in reverse, the camera will, sometimes come on, once I begin backing out, the camera will shut off and a message will appear. On some occasions, the camera …
Read full complaint
A few years ago, I brought my Edge into a dealership in Shawnee Mission, KS (Shawnee Mission Ford) for the rearview camera malfunctioning. What occurs is, once I put the car in reverse, the camera will, sometimes come on, once I begin backing out, the camera will shut off and a message will appear. On some occasions, the camera will operate, but 9 times out of 10 it will always go black with a pop up message. I want my vehicle to be included in the recall if the backup camera is the issue please.
The contact owns a 2013 Ford Edge. The contact stated that while attempting to start the vehicle, the contact became aware that the rearview camera displayed a blank screen or an upside-down image. An independent mechanic was contacted. The vehicle was not taken to a dealer or an independent mechanic to be diagnosed. The vehicle…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while attempting to start the vehicle, the contact became aware that the rearview camera displayed a blank screen or an upside-down image. An independent mechanic was contacted. The vehicle was not taken to a dealer or an independent mechanic to be diagnosed. The vehicle was not repaired. The contact related the failure to NHTSA Campaign Number: 25V270000 (BACK OVER PREVENTION); however, the VIN or the model year was not included in the recall. The manufacturer was not notified of the failure. The failure mileage was approximately 193,000.
Official recalls
214V393000 · Power Train:axle Assembly:axle Shaft
Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
14V002000 · Fuel System, Gasoline
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.