IllustrationThe rear backup camera is distorted and the image has flipped upside down
2013 Ford Edge
Owner reports · Recalls · Investigations
More warning signs than most Edge years
Owner complaints for the 2013 Ford Edge are substantially higher than the model-year median of 724.
About this comparison →How this year compares
Owner complaints by model year
Compare all Edge years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1470–25K
63025–50K
50950–75K
24575–100K
206100–150K
56150K+
1,793 reports with mileage · 651 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 854 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 529 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 300 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
33 crash reports7 fire reports24 injury reports
What owners actually said
2,444 reportsThe backup camera glitches repeatedly. Have to put in park then reverse and repeat until it displays. When it is producing the error, the alerts are not received to assist with alerting the driver of any potential hazards and you are unable to see due to camera not working. Also, happened in our 2014 Ford Escape. Although I pa…
Read full complaint
The backup camera glitches repeatedly. Have to put in park then reverse and repeat until it displays. When it is producing the error, the alerts are not received to assist with alerting the driver of any potential hazards and you are unable to see due to camera not working. Also, happened in our 2014 Ford Escape. Although I paid the dealership $600+ to replace it. Now receiving a notice for my 2017 Ford Edge regarding the malfunctioning camera and wondering why either of the other vehicles were not included in this recall.
245/50R-20 pirelli scorpion weather active xl. Unknown cause. 5/22/2026 found bulge in passenger side front tire outer sidewall. Tire can be kept for inspection
I have replaced all brake components except abs motor. After researching online this vehicle has same issues as stated with other models . Brake pedal goes to floor after spending $3500!
I am reporting a safety issue involving a 2013 Ford Edge Sport AWD related to progressive brake failure. The affected components include the brake booster and master cylinder. The vehicle remains available for inspection upon request. In mid-2025, the vehicle developed a gradual loss of braking capability. The brake pedal requi…
Read full complaint
I am reporting a safety issue involving a 2013 Ford Edge Sport AWD related to progressive brake failure. The affected components include the brake booster and master cylinder. The vehicle remains available for inspection upon request. In mid-2025, the vehicle developed a gradual loss of braking capability. The brake pedal required increasing force over time to bring the vehicle to a stop. Because the failure developed progressively rather than suddenly, the severity of the issue was not immediately apparent. At the time, the vehicle was primarily driven by my teenage son, a new driver, who continued operating the vehicle by pressing the brake pedal harder to compensate. This created a significant safety risk, as the vehicle did not reliably stop under normal braking conditions, increasing the risk of collision. The issue was confirmed by an independent mechanic, and repairs required replacement of the brake booster, master cylinder, and related components. The vehicle was later discussed with a Ford dealership; however, no warning of coverage or recall applicability was identified at that time. There were no clear warning lights or dashboard messages indicating brake system failure prior to the issue. The primary symptom was a progressive increase in required pedal force. After the repair, I learned that brake booster failure is a known issue for this vehicle platform and has been the subject of prior manufacturer service campaigns. I am concerned that this type of gradual brake degradation may not be recognized by drivers, particularly inexperienced drivers, and could result in unsafe operating conditions. The vehicle has also experienced repeated rear differential failures. Replacement parts are no longer manufactured by Ford, requiring use of used components with unknown condition and lifespan, further affecting vehicle reliability and safe operation. I have attached a receipt for the second time purchasing and replacing the rear differential.
The contact owns a 2013 Ford Edge. The contact stated that while driving at an undisclosed speed, after being cut off by another driver, the contact attempted to make an emergency stop; however, while the brake pedal was depressed, the brake pedal went to the floorboard, extending the braking distance. The vehicle failed to stop…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while driving at an undisclosed speed, after being cut off by another driver, the contact attempted to make an emergency stop; however, while the brake pedal was depressed, the brake pedal went to the floorboard, extending the braking distance. The vehicle failed to stop as intended, increasing the risk of a crash. The dealer was notified of the failure, but the vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 125,000.
On Dec 11, 2025, the driver’s heated seat in my 2013 Ford Edge overheated within minutes of activation, causing first- and second-degree burns to the occupant. The vehicle was inspected on March 18, 2026 and escalated for management review, but the manufacturer failed to provide the promised follow-up by March 26, 2026, and the …
Read full complaint
On Dec 11, 2025, the driver’s heated seat in my 2013 Ford Edge overheated within minutes of activation, causing first- and second-degree burns to the occupant. The vehicle was inspected on March 18, 2026 and escalated for management review, but the manufacturer failed to provide the promised follow-up by March 26, 2026, and the defect remains unresolved, posing an ongoing risk of injury. No problems prior to ever using the heated seats.
The panoramic sun roof exploded while going down the highway sending glass flying in the air. The sunroof shade was not open so the driver and 2 infants in the back seat were not injured. I contacted Ford Motor Company and was given a case number CZH-03059174. They directed me to turn it in to my insurance company which I did n…
Read full complaint
The panoramic sun roof exploded while going down the highway sending glass flying in the air. The sunroof shade was not open so the driver and 2 infants in the back seat were not injured. I contacted Ford Motor Company and was given a case number CZH-03059174. They directed me to turn it in to my insurance company which I did not do. I took the vehicle to the body shop, they found a replacement and installed it for less than my insurance deductible.
Back up Camera goes in and out, it's flips upside down and do wired things , it also say call dealership, the picture sometimes be in reverse , and brake light stays on have to pump brake in order for it to go off.
1. My safety system/camera system is no longer working properly. The screen displays either a black/blank screen, an inverted (upside down) image, or an image that appears to be zoomed in to a very small viewing area. The alerts (beeping) does not function consistently when backing up. The horn does not always work. At times the…
Read full complaint
1. My safety system/camera system is no longer working properly. The screen displays either a black/blank screen, an inverted (upside down) image, or an image that appears to be zoomed in to a very small viewing area. The alerts (beeping) does not function consistently when backing up. The horn does not always work. At times the entire electrical display including the sound system will reset without prompting. The back door hatch will actively close even when there is something in the opening. 2. Safety is at risk because the video system is in place as a secondary alert system to prevent accident or injury. The horn is a necessary item. If the electrical system should reset during operation this could cause an accident. The rear hatch could cause injury if it does close. 3. These issues have been witnessed by other people, but not in a dealership or service center because these places charge outrageous fees. 4. No inspection done by manufacturer/police/insurance. At time of state regulated inspection all aspects pertinent to that were functional 5. These issues began over a year ago with camera malfunction, the other issues have become present throughout that time.
Official recalls
214V393000 · Power Train:axle Assembly:axle Shaft
Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
14V002000 · Fuel System, Gasoline
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.