Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1470–25K
63025–50K
50950–75K
24575–100K
206100–150K
56150K+
1,793 reports with mileage · 651 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
Electrical System. Review the 854 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Service Brakes. Review the 529 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Structure. Review the 300 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
33 crash reports7 fire reports24 injury reports
What owners actually said
2,444 reports
Mileage unknown · Jun 2, 2024
Fuel/propulsion SystemService BrakesUnknown Or Other
My brakes are hard to press sometimes hard to stop. Jerky and then hard then soft. I read brake booster master cylinder or hcu All Ford's mistakes. Still no recall. I'm outside of the extended warranty because I just bought this 3 months ago and it's over 10 years old only 115000 miles on it. If I die I'm having my family sue f…
Read full complaint
My brakes are hard to press sometimes hard to stop. Jerky and then hard then soft. I read brake booster master cylinder or hcu All Ford's mistakes. Still no recall. I'm outside of the extended warranty because I just bought this 3 months ago and it's over 10 years old only 115000 miles on it. If I die I'm having my family sue ford. Codes p2 195 and p2 197 are now showing after a week and a half of this problem. Taking it to ford Tuesday. Calling customer service Monday. Shame on ford
NHTSA ODI #11591976
Mileage unknown · May 21, 2024
Service Brakes
There is a known issue with the Brake Booster on my vehicle that is covered by a warranty porgram. WHy hasnt the NHTSA required a recall on a key critical safety device that has been clearly identitifed?
NHTSA ODI #11589915
Mileage unknown · May 15, 2024
Back Over Prevention
Driving home, I entered my neighborhood and stopped to check my mail; i put my vehicle in park retrieved my mail and began to reverse out of the parking space, doing so the monitor screen flickered then a message came on the screen saying contact manufacturer camera unavailable. I then proceeded to put the car in drive and the m…
Read full complaint
Driving home, I entered my neighborhood and stopped to check my mail; i put my vehicle in park retrieved my mail and began to reverse out of the parking space, doing so the monitor screen flickered then a message came on the screen saying contact manufacturer camera unavailable. I then proceeded to put the car in drive and the message disappeared and the camera came back online. As i entered my driveway i put my car in park then reverse again and things were normal. This morning as i was backing out of my driveway the camera went black as well as no warning alarm or notification that i was approaching an individual and a few kids walking somewhat directly behind me, nearly hitting them. The last incident of the back up camera not working was this morning when i was nearly hit by oncoming traffic in the parking garage as i was trying to pull into a parking space and correct my position. These recent incidents have definitely put both my safety and that of my family in considerable risk as well as children in the neighborhood and at school. System failure: the back up camera Risk: children and adults could have been seriously injured Replacement: no the dealer has not been contacted as of yet 5/15/2024 Vehicle Inspection: none since purchase in 2019 Warnings or messages: Contact your Manufacturer Camera Not Available: 5/12/2024
NHTSA ODI #11588850
Mileage unknown · May 13, 2024
Service BrakesVehicle Speed Control
About a week ago my brakes on my 2013 Ford Edge Limited became for hard to press. The pedal became stiff. I almost was unable to stop even though I was going extremely slow approaching an intersection that was very busy. I have looked up recalls on this issue with the same description and realize Ford had issued a recall on 2013…
Read full complaint
About a week ago my brakes on my 2013 Ford Edge Limited became for hard to press. The pedal became stiff. I almost was unable to stop even though I was going extremely slow approaching an intersection that was very busy. I have looked up recalls on this issue with the same description and realize Ford had issued a recall on 2013 Ford Edges however only certain Vin numbers. However, surfing through multiple posts and forums I am finding 100's so far of people that are angry because Ford refused to own up to the fact the all these 2013 Ford Edges are having issues with the Brake Booster which is a major safety issue and should have no cut off period due to the importance of this defective part! I finally wad able to bring my car to the dealer due to the other mechanic's I brought it to are all getting an invalid read when they do the diagnostic test on the car. Now Ford Dealership Jarret Ford in Dade City said it will be $1389. 00 to fix my brake booster. This is highway robbery.
NHTSA ODI #11588587
158,000 miles · May 10, 2024
Interior LightingLatches/locks/linkages
The contact owns a 2013 Ford Edge. The contact stated while driving 35 MPH, the door ajar warning light illuminated while none of the doors were opened. The contact stated that the failure persisted, causing the interior lights to remain illuminated while the vehicle was parked and turned off. The contact stated that the interio…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated while driving 35 MPH, the door ajar warning light illuminated while none of the doors were opened. The contact stated that the failure persisted, causing the interior lights to remain illuminated while the vehicle was parked and turned off. The contact stated that the interior lights turned off after the battery was disconnected. The vehicle was taken to an independent mechanic, but the vehicle could not be diagnosed. The vehicle was not repaired. The dealer was notified of the failure and informed the contact that the vehicle was not covered under an unknown recall. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 158,000.
NHTSA ODI #11588008
Mileage unknown · May 5, 2024
Unknown Or Other
THE DRIVER DOOR LATCH ASSEMBLY WON'T ENGAGE WHEN YOU SHUT THE DOOR THE DOORV AJAR LIGHT STAYS ON AND YOU HAVE TO OPEN AND SHUT THE DOOR SEVERAL TIMES SLAMMING IT REAL HARD TO GET IT TO GO OUT YOU HAVE TO SPRAY WD-40 IN THE LATCH AND WORK IT TO GET THE DOOR TO LATCH.
NHTSA ODI #11587019
Mileage unknown · May 3, 2024
Engine
coolant leak from water pump
NHTSA ODI #11586772
114,000 miles · Apr 23, 2024
Power Train
The contact owns a 2013 Ford Edge. The contact stated while driving 45 MPH, upon acceleration, the vehicle began to shake and shudder. The check engine warning light was illuminated. The vehicle was taken to the local dealer, where it was diagnosed that the torque converter, hoses, and transmission needed to be replaced. The veh…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated while driving 45 MPH, upon acceleration, the vehicle began to shake and shudder. The check engine warning light was illuminated. The vehicle was taken to the local dealer, where it was diagnosed that the torque converter, hoses, and transmission needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 114,000.
NHTSA ODI #11584760
Mileage unknown · Apr 22, 2024
Service Brakes
I have experienced what feels like brakes going out numerous times. I will go to stop and it feels like I have no brakes. The pedal goes clear to the floor but i can end up stopping. This has not been diagnosed due to it does it occasionally then the brakes start working good again.
NHTSA ODI #11584568
150,000 miles · Apr 1, 2024
Service Brakes, Hydraulic
The contact owns a 2013 Ford Edge. The contact stated that while his wife was driving at various speeds and depressing the brake pedal, the brake pedal was rigid, and the vehicle failed to respond as needed. There was no warning light illuminated. The contact stated that the failure had been recurring intermittently while drivin…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while his wife was driving at various speeds and depressing the brake pedal, the brake pedal was rigid, and the vehicle failed to respond as needed. There was no warning light illuminated. The contact stated that the failure had been recurring intermittently while driving. The vehicle was taken to the dealer however, the failure could not be duplicated. The vehicle was then taken to an independent mechanic, where it was diagnosed that the brake booster had failed and needed to be replaced. The vehicle was not repaired. The contact related the failure to Ford Campaign Number: 13N02. The manufacturer was notified of the failure and informed the contact that the vehicle was not covered because the campaign had expired. A case was opened. The failure mileage was approximately 150,000.
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
2013 Ford Edge Problems, Complaints & Recalls | Skip That Year
Illustration