NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
2,444 reportsMileage unknown · Sep 7, 2024
Service Brakes
The brake booster has failed. When I depress the brake pedal it pushes almost to the floor before any braking occurs. The car is still able to brake, but this slight delay can pose a risk to safety if the car needs to be slowed quickly. The problem occurs constantly during driving. I have brought the care to the dealership…
Read full complaint
The brake booster has failed. When I depress the brake pedal it pushes almost to the floor before any braking occurs. The car is still able to brake, but this slight delay can pose a risk to safety if the car needs to be slowed quickly. The problem occurs constantly during driving. I have brought the care to the dealership to see if it was covered under the 13N02 customer satisfaction program, but they said my VIN indicated it was not. This problem is described exactly the same in the 13N02 recall and I believe my vehicle should be covered. There have been no warning lamps or signals for this issue.
NHTSA ODI #11613221
91,000 miles · Sep 6, 2024
Service BrakesService Brakes, Hydraulic
The contact owns a 2013 Ford Edge. The contact stated that while depressing the brake pedal, the brake pedal was spongy and depressed nearer to the floorboard. There were no warning lights illuminated. The vehicle was taken to the dealer where it was diagnosed and determined that the brake booster, front brake pads, and brake ma…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while depressing the brake pedal, the brake pedal was spongy and depressed nearer to the floorboard. There were no warning lights illuminated. The vehicle was taken to the dealer where it was diagnosed and determined that the brake booster, front brake pads, and brake master cylinder had failed and needed to be replaced. The brake booster, front brake pads, brake master cylinder, and approximately six other parts had been replaced. The brake pedal had become loose, causing the brake pedal to depress lower than before. The vehicle had been taken to an independent mechanic where it was diagnosed that the rear brake shoes had failed and needed to be replaced. The vehicle had been repaired. The brake pedal had gradually become more loose almost going to the floor. The vehicle had been returned to the independent mechanic where it was diagnosed that the ABS module had failed and needed to be replaced. The vehicle had not been repaired. The manufacturer was made aware of the failure and confirmed that the VIN was not under recall. The manufacturer referred the contact to the NHTSA Hotline to report the failure. The failure mileage was 91,000.
NHTSA ODI #11613031
114,000 miles · Sep 4, 2024
EngineEngine And Engine Cooling
The contact owns a 2013 Ford Edge. The contact stated that after arriving at her destination, the check engine warning light illuminated. The contact stated upon further inspection, she noticed a leak coming from the engine compartment. The vehicle was taken to a local independent mechanic who advised the contact to take the veh…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that after arriving at her destination, the check engine warning light illuminated. The contact stated upon further inspection, she noticed a leak coming from the engine compartment. The vehicle was taken to a local independent mechanic who advised the contact to take the vehicle to a local dealer for assistance. The vehicle was taken to a local dealer where it was diagnosed and determined that the water pump had failed, and that the front of the engine and the timing belt needed to be removed to reach the parts needed to be replaced. Additionally, the bearing behind the water pump needed to be replaced. The vehicle was not repaired due to the costs. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 114,000.
NHTSA ODI #11612584
Mileage unknown · Sep 3, 2024
Service BrakesUnknown Or Other
Tire Pressure Sensor Fault (TPS) Hissing sound when applying brakes. Brake pedal is hard and very difficult to bring the vehicle to a complete stop. When parked or at a traffic light you constantly hear air being released and vehicle will boggle for a few seconds then stall on me. When I bring the vehicle to a stop I have to put…
Read full complaint
Tire Pressure Sensor Fault (TPS) Hissing sound when applying brakes. Brake pedal is hard and very difficult to bring the vehicle to a complete stop. When parked or at a traffic light you constantly hear air being released and vehicle will boggle for a few seconds then stall on me. When I bring the vehicle to a stop I have to put it in park, and pump my brakes to stop the air from leaking to prevent it from stalling on me. Over all the vehicle is a huge safety concern and a hazard to have on the road.
NHTSA ODI #11612251
56,000 miles · Aug 29, 2024
Latches/locks/linkages
The contact owns a 2013 Ford Edge. The contact stated that upon entering the vehicle, the door-ajar warning light illuminated, after which the message, "Please Shift to Park" was displayed. The contact also stated that the interior lights remained illuminated continuously, greatly reducing nighttime visibility due to interior li…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that upon entering the vehicle, the door-ajar warning light illuminated, after which the message, "Please Shift to Park" was displayed. The contact also stated that the interior lights remained illuminated continuously, greatly reducing nighttime visibility due to interior light reflections. The vehicle was taken to the dealer, who diagnosed a failure with the door switch. The vehicle was not repaired. After investigating the failure, the contact related the failure to Customer Satisfaction Program: 19N09. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 56,000.
NHTSA ODI #11611683
115,000 miles · Aug 28, 2024
Service Brakes
The contact owns a 2013 Ford Edge. The contact stated while driving at an undisclosed speed, the brake pedal was depressed; however, the vehicle failed to stop as intended. The contact stated that the brake pedal needed to be depressed to the floorboard to stop the vehicle. The contact stated that the failure became persistent. …
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated while driving at an undisclosed speed, the brake pedal was depressed; however, the vehicle failed to stop as intended. The contact stated that the brake pedal needed to be depressed to the floorboard to stop the vehicle. The contact stated that the failure became persistent. The contact stated that the check engine warning light illuminated but then deactivated independently. The vehicle was taken to the independent mechanic and the dealer where it was diagnosed with brake booster failure. The contact was informed that the brake booster needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure but provided no assistance. The failure mileage was approximately 115,500.
NHTSA ODI #11611347
140,000 miles · Aug 27, 2024
Service Brakes, Hydraulic
The contact owns a 2013 Ford Edge. The contact stated that when the brake pedal was depressed, there was an abnormal whistling sound coming from the vehicle. There were no warning lights illuminated. The vehicle was taken to the local dealer, who informed the contact that the vehicle was not covered under a recall. The vehicle w…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that when the brake pedal was depressed, there was an abnormal whistling sound coming from the vehicle. There were no warning lights illuminated. The vehicle was taken to the local dealer, who informed the contact that the vehicle was not covered under a recall. The vehicle was not diagnosed or repaired. The vehicle was taken to an independent mechanic, who informed the contact that the failure was due to the brake booster. The contact was informed that the failure was linked to Customer Satisfaction Program: 13N02, Extended Warranty Coverage on Brake Booster. The manufacturer was contacted and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 140,000.
NHTSA ODI #11611232
Mileage unknown · Aug 23, 2024
Service Brakes
Vehicles Break booster and Master cylinder has an issue and the breaks are stiff with a whistle blowing sound when pressed. And causing a low engine oil sign to pop up and stall out when stopped. This happened while pulling out of a parking lot. The problem was confirmed by a Pep Boys Auto Repair Shop in Federal Way, Washington …
Read full complaint
Vehicles Break booster and Master cylinder has an issue and the breaks are stiff with a whistle blowing sound when pressed. And causing a low engine oil sign to pop up and stall out when stopped. This happened while pulling out of a parking lot. The problem was confirmed by a Pep Boys Auto Repair Shop in Federal Way, Washington State. No, insurance has not looked over it, and no I haven't taken it to be inspected by a Ford dealership/manufacturer
NHTSA ODI #11610541
157,000 miles · Aug 22, 2024
Service Brakes, Hydraulic
The contact owns a 2013 Ford Edge. The contact stated while driving at an undisclosed speed, the brake pedal was depressed; however, the vehicle failed to stop as intended. Additionally, the contact heard a loud sound coming from the vehicle. The contact stated that an unknown warning light illuminated but disappeared shortly a…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated while driving at an undisclosed speed, the brake pedal was depressed; however, the vehicle failed to stop as intended. Additionally, the contact heard a loud sound coming from the vehicle. The contact stated that an unknown warning light illuminated but disappeared shortly afterward. The contact drifted the vehicle to a nearby independent mechanic, where the failure was diagnosed as brake booster failure. The contact was informed that the brake booster needed to be replaced. The vehicle was repaired. The manufacturer was made aware of the failure and a case was filed. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 157,000.
NHTSA ODI #11610307
Mileage unknown · Aug 20, 2024
Fuel/propulsion System
The fuel tank has a crack in the top causing fuel leaking when the tank is full. This has been confirmed by an independent service center. cost to replace the tank is approximately 3000$
NHTSA ODI #11609832
Official recalls
2Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Illustration