NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
2,444 reportsMileage unknown · Apr 22, 2025
Service Brakes
Brake booster needs to be replaced because it has failed, making the car unable to stop. This has caused the car to shut off if the brake pedal is pressed to long, like stopping at a stop light. The vehicle is in a Ford authorized service shop and has been confirmed as brake booster failure. The issue started with stalling, car …
Read full complaint
Brake booster needs to be replaced because it has failed, making the car unable to stop. This has caused the car to shut off if the brake pedal is pressed to long, like stopping at a stop light. The vehicle is in a Ford authorized service shop and has been confirmed as brake booster failure. The issue started with stalling, car throwing codes such as no oil, hissing in the brake lines, spongy brake pedal, leading to zero ability to stop. Issues started slowly around October and by January, the car is completely unable to stop.
NHTSA ODI #11656067
Mileage unknown · Apr 16, 2025
Electrical SystemExterior Lighting
Interior lights stay on much too long after turning vehicle off, even several hours. Dash and bell indicators indicates doors are open when they are not. Door locks operate open while driving.
NHTSA ODI #11654925
Mileage unknown · Apr 13, 2025
Service Brakes
Brake Boost issue with my 2013 Ford Edge Sport. When attempting to brake, there is very little stopping resistance. Even at slow speeds, it takes a dangerous amount of time and distance to bring the vehicle to a stop. While braking, a hissing noise can be heard from the brake pedal area, and the brake pedal presses easily to the…
Read full complaint
Brake Boost issue with my 2013 Ford Edge Sport. When attempting to brake, there is very little stopping resistance. Even at slow speeds, it takes a dangerous amount of time and distance to bring the vehicle to a stop. While braking, a hissing noise can be heard from the brake pedal area, and the brake pedal presses easily to the floor with minimal resistance. Upon researching the issue, I discovered that this is a very common problem with this vehicle. A certified mechanic diagnosed the issue and stated that this is a known problem and may be covered under Ford's Customer Satisfaction Program 13N02. While this is a known and common issue that is covered under warranty when the vehicle is under 10 years from warranty purchase date or under 150,000 miles, the Ford Dealership is fighting me on this and is refusing to assist in correcting this safety issue. If a vehicle has already exceeded the time or mileage limit and is part of the incremental launch population, this coverage will last through November 30, 2025. Coverage is automatically transferred to subsequent owners. Brakes began failing around July/August of 2024. Due to financial hardship, I cannot afford this repair on my own. Driving this vehicle in this condition is extremely dangerous for myself and other drivers on the road. I've had to veer off of the road or into other lanes in order to avoid a collision with vehicles in front of me because it takes an extremely unreasonable distance to stop the vehicle with a bad brake booster many times already; It's only a matter of time before I encounter an unavoidable collision due to bad brakes. Please advise on who I can talk to about getting this issue fixed under warranty, or at no/reduced cost.
NHTSA ODI #11654355
140,000 miles · Apr 10, 2025
Back Over Prevention
The contact owns a 2013 Ford Edge. The contact stated that upon attempting to reverse out of the driveway, the rear-view camera image displayed on the center console was upside down. There was no warning light illuminated. The local dealer was contacted; however, the vehicle was not diagnosed. The contact was informed that the V…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that upon attempting to reverse out of the driveway, the rear-view camera image displayed on the center console was upside down. There was no warning light illuminated. The local dealer was contacted; however, the vehicle was not diagnosed. The contact was informed that the VIN was not under recall. The vehicle was not repaired. The manufacturer was notified of the failure. The approximate failure mileage was 140,000.
NHTSA ODI #11653849
Mileage unknown · Apr 8, 2025
Service Brakes
My brake pedal was not functioning correct. It was at times very soft, hitting the floor, and at other times difficult to push. A local shop replaced booster and master cylinder in an attempt to fix. Now brakes are locking up at random. Happened while going 70 mph with family in car and wheel was shaking and very unsafe. My ye…
Read full complaint
My brake pedal was not functioning correct. It was at times very soft, hitting the floor, and at other times difficult to push. A local shop replaced booster and master cylinder in an attempt to fix. Now brakes are locking up at random. Happened while going 70 mph with family in car and wheel was shaking and very unsafe. My year model (2013) is not included in the extended warranty for the brake booster (13N02) anymore since it was made in March of 2013. Any edges made in April of 2013, just one month later, are covered until 2025 by the customer satisfaction program extended warranty.
NHTSA ODI #11653482
Mileage unknown · Mar 31, 2025
Service Brakes
Yes, the vehicle is available for inspection upon request. The vehicle is hard to brake and travels a further distance before stopping, the brake is hard to press and stop the vehicle. This has been confirmed by my private mechanic No, it has not been inspected by the manufacturer I heard a hissing noise and the car stalled out…
Read full complaint
Yes, the vehicle is available for inspection upon request. The vehicle is hard to brake and travels a further distance before stopping, the brake is hard to press and stop the vehicle. This has been confirmed by my private mechanic No, it has not been inspected by the manufacturer I heard a hissing noise and the car stalled out at a complete stop when the brakes were pressed down Reached out to Ford and they said there is no recall for my vehicle but I have information from when I had my emission done provided by NHTSA of a recall MRF#13N02. Which I've provided a copy of down below.
NHTSA ODI #11651903
Mileage unknown · Mar 24, 2025
Tires
I purchased these tires and they were installed on 1/19/25. I paid $426.20 including the installation fees. After installation we noticed the tires were extremely loud above 40 MPH. We returned and had the tires balanced again and the noise problem continued. It drowned out the cabin and made it difficult to hear anything ou…
Read full complaint
I purchased these tires and they were installed on 1/19/25. I paid $426.20 including the installation fees. After installation we noticed the tires were extremely loud above 40 MPH. We returned and had the tires balanced again and the noise problem continued. It drowned out the cabin and made it difficult to hear anything outside of the vehicle. The poor customer service department made me complete a warranty request which was denied within hours because the warranty doesn’t cover noise. They refused to take any responsibility for this hazardous issue that was previously reported. They claim their tires are quiet on various sites, but this is false. There have been many reports to Arroyo and they are not willing to address the unsafe issue. Various reviews on the internet express the same concerns about excessive noise. I replaced the scary tires with another set and they are very quiet and don’t produce the excess noise like the Arroyo tires. 245/50ZR20 102W
NHTSA ODI #11650146
122,000 miles · Mar 21, 2025
Fuel System, GasolinePower Train
The contact owns a 2013 Ford Edge. The contact stated that while driving 50 MPH, the accelerator pedal was depressed, and the vehicle failed to respond. The check engine and ABS warning lights were illuminated. The contact stated that after refueling, the vehicle started to jerk while driving. The contact stated that once the ve…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while driving 50 MPH, the accelerator pedal was depressed, and the vehicle failed to respond. The check engine and ABS warning lights were illuminated. The contact stated that after refueling, the vehicle started to jerk while driving. The contact stated that once the vehicle while driving at speed, there was an abnormal thumping sound coming from the vehicle. The check engine and ABS warning lights were intermittently illuminated. The vehicle was not taken to an independent mechanic or a dealer to be diagnosed; however, the contact self-diagnosed the vehicle with fuel pump and power train failure. The dealer was not made aware of the failure. The manufacturer was not made aware of the failure. The failure mileage was approximately 122,000.
NHTSA ODI #11649827
Mileage unknown · Mar 20, 2025
Service Brakes
The brake booster on my 2013 Ford Edge Sport has failed, leading to significantly reduced braking performance. This creates a dangerous condition requiring excessive force to stop the vehicle. Over the past few months, I have narrowly avoided multiple accidents due to the inability to stop safely at stoplights. On several occasi…
Read full complaint
The brake booster on my 2013 Ford Edge Sport has failed, leading to significantly reduced braking performance. This creates a dangerous condition requiring excessive force to stop the vehicle. Over the past few months, I have narrowly avoided multiple accidents due to the inability to stop safely at stoplights. On several occasions, I was forced to swerve off the road to avoid collisions. This issue was diagnosed by a certified mechanic, who informed me that brake booster failures are a known problem in this vehicle model. Although I was made aware of Ford's Customer Satisfaction Program 13N02, Ford's customer service indicated that the warranty had expired, and the dealership refused to repair the issue at no cost. As I cannot afford the repair myself, I am forced to continue driving the vehicle in its unsafe condition, putting my safety and the safety of others at risk.
NHTSA ODI #11649622
85,000 miles · Mar 12, 2025
Service Brakes, Hydraulic
The contact owns a 2013 Ford Edge. The contact stated while driving out of a parking lot from a complete stop and depressing the brake pedal, the brake pedal went down to the floorboard, and the vehicle failed to respond as needed. There was no warning light illuminated. The contact pumped the brake pedal several times and the v…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated while driving out of a parking lot from a complete stop and depressing the brake pedal, the brake pedal went down to the floorboard, and the vehicle failed to respond as needed. There was no warning light illuminated. The contact pumped the brake pedal several times and the vehicle responded as needed; however, the failure recurred while driving to the dealer. The vehicle was taken to the dealer, where diagnostic trouble code U041-68 was retrieved, and the dealer diagnosed that the HCU and ABS modules had failed and needed to be replaced; however, the part was on backorder. The vehicle was not repaired. The manufacturer was notified of the failure and informed the contact that the process of shipping the part to the dealer would be expedited. The manufacturer referred the contact to the NHTSA Hotline for assistance. The contact stated that the vehicle could be repaired by an independent mechanic due to the cost. The vehicle was not repaired. The failure mileage was approximately 85,000.
NHTSA ODI #11647830
Official recalls
2Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Illustration