NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
2,444 reports34,000 miles · Jun 6, 2025
Service Brakes, Hydraulic
The contact owns a 2013 Ford Edge. The contact stated while the vehicle was parked, the gear shifter was shifted into reverse; however, with the contact’s foot on the brake pedal, the vehicle rolled backwards. The contact depressed the brake pedal to the floorboard; however, the vehicle failed to stop. The contact activated the…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated while the vehicle was parked, the gear shifter was shifted into reverse; however, with the contact’s foot on the brake pedal, the vehicle rolled backwards. The contact depressed the brake pedal to the floorboard; however, the vehicle failed to stop. The contact activated the parking brake to stop the vehicle. The vehicle was inspected by several independent mechanics who confirmed a failure with the electronic braking system and brake master cylinder failure. The contact was informed that the electronic braking system and the brake master cylinder needed to be replaced. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 34,000.
NHTSA ODI #11665386
100,000 miles · Jun 5, 2025
Back Over Prevention
The contact owns a 2013 Ford Edge. The contact stated that while reversing, the back over prevention camera failed to function as intended. The contact stated that the back over prevention camera image was delayed and then became frozen. The vehicle was taken to an independent mechanic, where it was diagnosed with a software fai…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while reversing, the back over prevention camera failed to function as intended. The contact stated that the back over prevention camera image was delayed and then became frozen. The vehicle was taken to an independent mechanic, where it was diagnosed with a software failure. The contact was advised to take the vehicle to the dealer for assistance. The dealer was made aware of the failure. The manufacturer was made aware of the failure. The contact was informed that the repair was not covered under recall or warranty. The contact was advised to contact the NHTSA Hotline to report the failure. The failure mileage was approximately 100,000.
NHTSA ODI #11665165
Mileage unknown · Jun 3, 2025
Electrical System
Last week my back up camera said there was a system error and only works sometimes now. I almost hit somebody because it started showing it was working and then it went black and then wouldn’t work again. I also have a video where it starts to show me backing up and then cuts out to being black and seeing contact your dealership…
Read full complaint
Last week my back up camera said there was a system error and only works sometimes now. I almost hit somebody because it started showing it was working and then it went black and then wouldn’t work again. I also have a video where it starts to show me backing up and then cuts out to being black and seeing contact your dealership. I did contact the dealership and they said there is not a recall in regards to my car specifically.
NHTSA ODI #11664516
170,000 miles · Jun 2, 2025
Engine And Engine CoolingFuel System, Gasoline
The contact owns a 2013 Ford Edge. The contact stated that while his wife was driving 80 MPH, the vehicle lost motive power while the RPMs exceeded 5,000 RPM. The contact stated that the check engine warning light was flashing. The driver was able to pull over to the side of the road. The contact stated that his wife turned off …
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while his wife was driving 80 MPH, the vehicle lost motive power while the RPMs exceeded 5,000 RPM. The contact stated that the check engine warning light was flashing. The driver was able to pull over to the side of the road. The contact stated that his wife turned off and restarted the vehicle, and the vehicle was on LIMP Mode. The contact's wife was able to drive to the residence. A mobile mechanic diagnosed the vehicle at the residence and informed the contact that there was a misfire in cylinder #2. The mechanic advised the contact that the failure could be related to the coil packs, the fuel injectors, or the fuel lines. The vehicle was not repaired. The dealer was not notified of the failure. The manufacturer was notified of the failure and a case was filed. The contact was referred to the NHTSA Hotline for assistance. The failure mileage was approximately 170,000.
NHTSA ODI #11664318
Mileage unknown · May 31, 2025
Service Brakes
ABS hydraulic module went out Brakes go to the floor, however ford has not recall for the part even with the known issue of the part. yes- confirmed by a master tech no warning present, only the symptoms of brakes going all the way to the floor and acting like there is air in the lines
NHTSA ODI #11664144
Mileage unknown · May 29, 2025
Service Brakes
Brake failure - should be a recall for my VIN under the attached program. Ford is denying and told me to reach out to NHTSA.
NHTSA ODI #11663657
Mileage unknown · May 28, 2025
Service Brakes
My brakes are failing intermittently. I have been driving and pressed the brake pedal and it goes all the way to the floor but the car only gradually stops. Thankfully it has not caused an accident, yet. Once I am able to stop I pump the pedal to get things back to somewhat normal. But the pedal still feels spongy. I looked up a…
Read full complaint
My brakes are failing intermittently. I have been driving and pressed the brake pedal and it goes all the way to the floor but the car only gradually stops. Thankfully it has not caused an accident, yet. Once I am able to stop I pump the pedal to get things back to somewhat normal. But the pedal still feels spongy. I looked up a customer service program ford has (13N02) but my VIN isn’t under it. But my car does fit the assembly plant and dates of this known issue. I’m afraid I’m going to get in an accident over a known issue.
NHTSA ODI #11663509
Mileage unknown · May 28, 2025
Electrical SystemUnknown Or OtherVisibility/wiper
Rear view (back up) camera works only on and off. The screen goes black and a warning to contact the dealer shows up. It is getting more and more frequent lately. I am having a very hard time in crowded parking lots. Now it has stopped completely.
NHTSA ODI #11663319
68,014 miles · May 27, 2025
Power Train
The contact owns a 2013 Ford Edge. The contact stated that while driving at 10 MPH, the vehicle stalled with no warning light illuminated. The vehicle was towed to an independent mechanic, where it was diagnosed that the power transfer unit had failed and needed to be replaced. The vehicle was repaired. The dealer was not contac…
Read full complaint
The contact owns a 2013 Ford Edge. The contact stated that while driving at 10 MPH, the vehicle stalled with no warning light illuminated. The vehicle was towed to an independent mechanic, where it was diagnosed that the power transfer unit had failed and needed to be replaced. The vehicle was repaired. The dealer was not contacted. The vehicle was not diagnosed or repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 68,014.
NHTSA ODI #11663094
Mileage unknown · May 22, 2025
Unknown Or Other
The sun roof failed to close when it was wide open. I manually pushed it close most of the way, but could not get it to completely close. A google search has shown that other Ford Edges have had this problem. I have garbage bags taped around the opening to help prevent water getting in, but water still has gotten in which can ca…
Read full complaint
The sun roof failed to close when it was wide open. I manually pushed it close most of the way, but could not get it to completely close. A google search has shown that other Ford Edges have had this problem. I have garbage bags taped around the opening to help prevent water getting in, but water still has gotten in which can cause damage.
NHTSA ODI #11662571
Official recalls
2Jul 2, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2014 Ford Edge and Lincoln MKX vehicles manufactured September 2, 2010, to November 30, 2013; 2013-2014 Ford Taurus and Lincoln MKS vehicles manufactured August 25, 2011, to November 30, 2013; and 2013-2014 Ford Flex and Lincoln MKT vehicles manufactured September 12, 2011, to November 30, 2013. In the affected vehicles, the halfshaft retention circlip may not have been properly installed, and as a result, the halfshaft may move outward and disengage from the linkshaft while driving and without prior warning.
Consequence & remedy
Consequence: If the halfshaft and linkshaft become disengaged while driving, power will no longer be transmitted to the wheels, increasing the risk of a vehicle crash. Additionally, if the parking brake is not applied before exiting the vehicle, the vehicle may roll away despite the transmission being placed in 'Park', increasing the risk of injury to exiting occupants and bystanders.
Remedy: Ford will notify owners, and dealers will inspect the vehicles to make sure that the halfshaft is properly retained. If it is not, dealers will replace the linkshaft and also replace the halfshaft if it shows evidence of spline damage, free of charge. The recall began on August 4, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S10.
Jan 6, 2014
Ford Motor Company (Ford) is recalling certain model year 2012-2013 Edge vehicles manufactured from September 2, 2010, through April 25, 2013, and equipped with 2.0L engines. The fuel line pulse damper metal housing may crack as a result of an improper manufacturing process. A cracked fuel line pulse damper housing may result in a combination of fuel odor, weepage, or a continuous leak while the fuel system is pressurized.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source may result in a fire.
Remedy: Ford will notify owners, and dealers will replace the fuel line with one that does not have a damper, free of charge. The safety recall began on February 25, 2014. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 13S13. IMPORTANT: This recall supersedes recall 12V-438. All vehicles that have been remedied under the previous recall need to have the current remedy applied.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE16012 · Door Ajar Warning Light Always On
Opened Sep 28, 2016 · Closed Mar 20, 2017
Status: closed (inferred from source dates) · Interior Lighting; Latches/locks/linkages; Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Additional source detail variants (3)
Interior Lighting
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages:doors:latch
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Latches/locks/linkages
The Office of Defects Investigation (ODI) opened this investigation on September 28, 2016 based on allegations that the door ajar light located on the instrument cluster stays on all of the time even when all doors are closed and fully latched on 2011-2013 model year Ford Edge vehicles.When the light is illuminated continuously, vehicle occupants cannot be certain if any of the doors are properly latched.Reported safety consequences as a result of this issue include doors opening while driving (because doors were initially not latched properly), doors cannot be locked while driving, and the interior dome lights staying on continuously. Ford data received from the Information Request letter corresponding to this investigation indicates the failures were caused by contamination of the electrical contacts on the switch located within each door latch that tells the vehicle if the door is open or closed.All four doors contain the same latch design and switch.According to Ford, the Body Control Module (BCM) monitors the position of the switch and continuously samples it to detect a state of change.After a closed door state is detected, a continuous wetting current designed to keep the electrical contacts clean is sent from the BCM to the switches as long as the BCM is active.Beginning with the 2011 model year Edge vehicles, a change in BCM strategy resulted in a reduction of the wetting current sent out to clean the switch contacts by more than 75%.Over time, this low level of current is not sufficient to keep the switch contacts clean and contamination build up causes them to fail as described above.During the course of this investigation, ODI has identified a total of 1,983 complaints related to the door ajar light.Of these complaints, 14 indicated that a door opened while driving.Twelve of the 14 door opening events were situations where an occupant of the vehicle (often a child) opened a passenger door because the doors were not locked.The remaining two complaints involved a door opening on its own because the driver was unaware that the door was unlatched.There were no accidents but one complainant reported that a shoulder injury was caused by the driver having to repeatedly slam the door in an effort to get the door ajar light to turn off.After reviewing all available data, an unreasonable risk to motor vehicle safety has not been identified.The door latches themselves continue to function properly, remaining securely latched until acted upon by a driver or passenger.Child safety locks on the rear doors continue to function properly and can be used to prevent the rear doors from opening via the inside door handles.Vehicle crashworthiness is not affected by the lock condition of the doors and all active safety systems continue to function normally even if the vehicle BCM believes one or more doors is open.In addition, no accidents or accident related injuries have been reported.A safety-related defect trend has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, the investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor the issue and reserves the right to take future action if warranted by the circumstances.ODI numbers for the reports cited above are shown in the attached document.
Illustration